123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <https://www.gnu.org/licenses/>.
- *
- */
- #pragma once
-
- /**
- * Arduino Due with RAMPS-SMART pin assignments
- *
- * Applies to the following boards:
- *
- * RAMPS_SMART_EFB (Hotend, Fan, Bed)
- * RAMPS_SMART_EEB (Hotend0, Hotend1, Bed)
- * RAMPS_SMART_EFF (Hotend, Fan0, Fan1)
- * RAMPS_SMART_EEF (Hotend0, Hotend1, Fan)
- * RAMPS_SMART_SF (Spindle, Controller Fan)
- *
- * Differences between
- * RAMPS_14 | RAMPS-SMART
- * NONE | D16 (Additional AUX-3 pin(AUX3_2PIN), shares the same pin with AUX4_18PIN)
- * NONE | D17 (Additional AUX-3 pin(AUX3_1PIN), shares the same pin with AUX4_17PIN)
- * D0 | NONE
- * D1 | NONE
- * A3/D57 | NONE
- * A4/D58 | NONE
- * A5/D59 | A3/D57
- * A9/D63 | A4/D58
- * A10/D64 | A5/D59
- * A11/D65 | D66
- * A12/D66 | D67
- * A13 | A9
- * A14 | A10
- * A15 | A11
- *
- *
- * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER works fine connected to AUX-4 with
- * Smart Adapter, but requires removing the AUX3 pin header on the adapter to fit.
- * To use the SD card reader, wire its pins to AUX-3 (and use Software SPI).
- *
- * To use Hardware SPI for SD, the SDSS pin must be set to 52 instead of 53.
- * Hardware SPI also requires additional wiring because the board doesn't pass
- * the 6-pin SPI header from the DUE board.
- * (Search the web for "Arduino DUE Board Pinout" to see the correct header.)
- */
-
- #define BOARD_INFO_NAME "RAMPS-SMART"
-
- // I2C EEPROM with 4K of space
- #define I2C_EEPROM
- #define MARLIN_EEPROM_SIZE 0x1000 // 4K
-
- // See EEPROM device datasheet for the following values. These are for 24xx256
- #define EEPROM_DEVICE_ADDRESS 0x50 // 7 bit i2c address (without R/W bit)
- #define EEPROM_WRITE_DELAY 7 // page write time in milliseconds (docs say 5ms but that is too short)
- //#define EEPROM_PAGE_SIZE 64 // page write buffer size
- //#define TWI_CLOCK_FREQ 400000
- //#define EEPROM_ADDRSZ_BYTES TWI_MMR_IADRSZ_2_BYTE // TWI_MMR_IADRSZ_1_BYTE for 1 byte, or TWI_MMR_IADRSZ_2_BYTE for 2 byte
- //#define EEPROM_AVAILABLE EEPROM_I2C
-
- //
- // Temperature Sensors
- //
- #define TEMP_0_PIN 9 // Analog Input
- #define TEMP_1_PIN 10 // Analog Input
- #define TEMP_BED_PIN 11 // Analog Input
-
- // SPI for MAX Thermocouple
- #if DISABLED(SDSUPPORT)
- #define TEMP_0_CS_PIN 67 // Don't use 53 if using Display/SD card
- #else
- #define TEMP_0_CS_PIN 67 // Don't use 49 (SD_DETECT_PIN)
- #endif
-
- #define SDA_PIN 20
- #define SCL_PIN 21
- #define RESET_PIN 42 // Resets the board if the jumper is attached
-
- //
- // LCD / Controller
- //
- #if ENABLED(AZSMZ_12864)
-
- // Support for AZSMZ 12864 LCD with SD Card 3D printer smart controller control panel
- #define BEEPER_PIN 66 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 65
- #define DOGLCD_A0 59
- #define DOGLCD_CS 44
- #define BTN_EN1 58
- #define BTN_EN2 40
- #define BTN_ENC 67 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 66
- #define SD_DETECT_PIN 49 // Pin 49 for display sd interface, 72 for easy adapter board
- #define KILL_PIN 42
-
- #else
-
- /** ------ ------
- * 37 | 1 2 | 35 (MISO) 50 | 1 2 | 52 (SCK)
- * 31 | 3 4 | 41 29 | 3 4 | 53
- * 33 5 6 | 23 25 5 6 | 51 (MOSI)
- * 42 | 7 8 | 44 49 | 7 8 | 27
- * GND | 9 10 | 5V GND | 9 10 | --
- * ------ ------
- * EXP1 EXP2
- */
- #define EXP1_01_PIN 37
- #define EXP1_02_PIN 35
- #define EXP1_03_PIN 31
- #define EXP1_04_PIN 41
- #define EXP1_05_PIN 33
- #define EXP1_06_PIN 23
- #define EXP1_07_PIN 42
- #define EXP1_08_PIN 44
-
- #define EXP2_01_PIN 50
- #define EXP2_02_PIN 52
- #define EXP2_03_PIN 29
- #define EXP2_04_PIN 53
- #define EXP2_05_PIN 25
- #define EXP2_06_PIN 51
- #define EXP2_07_PIN 49
- #define EXP2_08_PIN 27
-
- #endif
-
- #define ALLOW_SAM3X8E
- #include "../ramps/pins_RAMPS.h"
|