123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- *
- */
- #pragma once
-
- #ifdef SKR_HAS_LPC1769
- #ifndef MCU_LPC1769
- #error "Oops! Make sure you have the LPC1769 environment selected in your IDE."
- #endif
- #elif !defined(MCU_LPC1768)
- #error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
- #endif
-
- // Ignore temp readings during development.
- //#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
-
- #if DISABLED(SDCARD_EEPROM_EMULATION)
- #define FLASH_EEPROM_EMULATION
- #endif
-
- //
- // Steppers
- //
- #ifndef E1_STEP_PIN
- #define E1_STEP_PIN P0_01
- #endif
- #ifndef E1_DIR_PIN
- #define E1_DIR_PIN P0_00
- #endif
- #ifndef E1_ENABLE_PIN
- #define E1_ENABLE_PIN P0_10
- #endif
-
- //
- // Temperature Sensors
- // 3.3V max when defined as an analog input
- //
- #ifndef TEMP_0_PIN
- #define TEMP_0_PIN P0_24_A1 // A1 (T1) - (68) - TEMP_0_PIN
- #endif
- #ifndef TEMP_1_PIN
- #define TEMP_1_PIN P0_25_A2 // A2 (T2) - (69) - TEMP_1_PIN
- #endif
- #ifndef TEMP_BED_PIN
- #define TEMP_BED_PIN P0_23_A0 // A0 (T0) - (67) - TEMP_BED_PIN
- #endif
-
- #if HOTENDS == 1 && TEMP_SENSOR_PROBE
- #define TEMP_PROBE_PIN TEMP_1_PIN
- #endif
-
- //
- // Heaters / Fans
- //
- #ifndef HEATER_0_PIN
- #define HEATER_0_PIN P2_07
- #endif
- #if HOTENDS == 1
- #ifndef FAN1_PIN
- #define FAN1_PIN P2_04
- #endif
- #else
- #ifndef HEATER_1_PIN
- #define HEATER_1_PIN P2_04
- #endif
- #endif
- #ifndef FAN_PIN
- #define FAN_PIN P2_03
- #endif
- #ifndef HEATER_BED_PIN
- #define HEATER_BED_PIN P2_05
- #endif
-
- //
- // LCD / Controller
- //
- #if HAS_SPI_LCD
- #define BEEPER_PIN P1_30 // (37) not 5V tolerant
- #endif
-
- //
- // SD Support
- //
- #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card
-
- #if SD_CONNECTION_IS(LCD)
- #define SCK_PIN P0_15
- #define MISO_PIN P0_17
- #define MOSI_PIN P0_18
- #elif SD_CONNECTION_IS(ONBOARD)
- #undef SD_DETECT_PIN
- #define SD_DETECT_PIN P0_27
- #define SCK_PIN P0_07
- #define MISO_PIN P0_08
- #define MOSI_PIN P0_09
- #define SS_PIN ONBOARD_SD_CS_PIN
- #elif SD_CONNECTION_IS(CUSTOM_CABLE)
- #error "No custom SD drive cable defined for this board."
- #endif
|