marlin/Marlin/Configuration.h

#ifndef __CONFIGURATION_H
#define __CONFIGURATION_H



// This determines the communication speed of the printer
#define BAUDRATE 250000
//#define BAUDRATE 115200
//#define BAUDRATE 230400

#define EXTRUDERS 1

// Frequency limit
// See nophead's blog for more info
// Not working O
//#define XY_FREQUENCY_LIMIT  15

// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
// of the buffer and all stops. This should not be much greater than zero and should only be changed
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
#define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec)

// BASIC SETTINGS: select your board type, thermistor type, axis scaling, and endstop configuration

//// The following define selects which electronics board you have. Please choose the one that matches your setup
// MEGA/RAMPS up to 1.2 = 3,
// RAMPS 1.3 = 33
// Gen6 = 5,
// Sanguinololu 1.2 and above = 62
// Ultimaker = 7,
// Teensylu = 8,
// Gen3+ =9
#define MOTHERBOARD 7

//===========================================================================
//=============================Thermal Settings  ============================
//===========================================================================

//// Thermistor settings:
// 1 is 100k thermistor
// 2 is 200k thermistor
// 3 is mendel-parts thermistor
// 4 is 10k thermistor
// 5 is ParCan supplied 104GT-2 100K
// 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01

//#define THERMISTORHEATER_0 3
//#define THERMISTORHEATER_1 1
//#define THERMISTORHEATER_2 1

//#define HEATER_0_USES_THERMISTOR
//#define HEATER_1_USES_THERMISTOR
//#define HEATER_2_USES_THERMISTOR
#define HEATER_0_USES_AD595
//#define HEATER_1_USES_AD595
//#define HEATER_2_USES_AD595
//#define HEATER_0_USES_MAX6675
 

// Select one of these only to define how the bed temp is read.
//#define THERMISTORBED 1
//#define BED_USES_THERMISTOR
//#define BED_LIMIT_SWITCHING
#ifdef BED_LIMIT_SWITCHING
  #define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
#endif
//#define BED_USES_AD595

#define BED_CHECK_INTERVAL 5000 //ms

//// Heating sanity check:
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero. 
// It can be reset with another M104/M109
//#define WATCHPERIOD 20000 //20 seconds

// Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 30  // (seconds)
#define TEMP_HYSTERESIS 3       // (C°) range of +/- temperatures considered "close" to the target one

//// The minimal temperature defines the temperature below which the heater will not be enabled
#define HEATER_0_MINTEMP 5
//#define HEATER_1_MINTEMP 5
//#define HEATER_2_MINTEMP 5
//#define BED_MINTEMP 5


// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275
//#define HEATER_1_MAXTEMP 275
//#define HEATER_2_MAXTEMP 275
//#define BED_MAXTEMP 150


// Wait for Cooldown
// This defines if the M109 call should not block if it is cooling down.
// example: From a current temp of 220, you set M109 S200. 
// if CooldownNoWait is defined M109 will not wait for the cooldown to finish
#define CooldownNoWait true

// Heating is finished if a temperature close to this degree shift is reached
#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree

// PID settings:
// Uncomment the following line to enable PID support.
#define PIDTEMP
#define PID_MAX 255 // limits current to nozzle; 255=full current
#ifdef PIDTEMP
  //#define PID_DEBUG // Sends debug data to the serial port. 
  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
  #define PID_INTEGRAL_DRIVE_MAX 255  //limit for the integral term
  #define K1 0.95 //smoothing factor withing the PID
  #define PID_dT 0.128 //sampling period of the PID

  //To develop some PID settings for your machine, you can initiall follow 
  // the Ziegler-Nichols method.
  // set Ki and Kd to zero. 
  // heat with a defined Kp and see if the temperature stabilizes
  // ideally you do this graphically with repg.
  // the PID_CRITIAL_GAIN should be the Kp at which temperature oscillatins are not dampned out/decreas in amplitutde
  // PID_SWING_AT_CRITIAL is the time for a full period of the oscillations at the critical Gain
  // usually further manual tunine is necessary.

  #define PID_CRITIAL_GAIN 50
  #define PID_SWING_AT_CRITIAL 47 //seconds
  
  //#define PID_PI    //no differentail term
  #define PID_PID //normal PID

  #ifdef PID_PID
    //PID according to Ziegler-Nichols method
//    #define  DEFAULT_Kp  (0.6*PID_CRITIAL_GAIN)
//    #define  DEFAULT_Ki (2*Kp/PID_SWING_AT_CRITIAL*PID_dT)  
//    #define  DEFAULT_Kd (PID_SWING_AT_CRITIAL/8./PID_dT)  

// Ultitmaker
    #define  DEFAULT_Kp  22.2
    #define  DEFAULT_Ki (1.25*PID_dT)  
    #define  DEFAULT_Kd (99/PID_dT)  

// Makergear
//    #define  DEFAULT_Kp 7.0
//    #define  DEFAULT_Ki 0.1  
//    #define  DEFAULT_Kd 12  

// Mendel Parts V9 on 12V    
//    #define  DEFAULT_Kp  63.0
//    #define  DEFAULT_Ki (2.25*PID_dT)  
//    #define  DEFAULT_Kd (440/PID_dT)  
  #endif
   
  #ifdef PID_PI
    //PI according to Ziegler-Nichols method
    #define  DEFAULT_Kp (PID_CRITIAL_GAIN/2.2) 
    #define  DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
    #define  DEFAULT_Kd (0)
  #endif
  
  // this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
  // if Kc is choosen well, the additional required power due to increased melting should be compensated.
  #define PID_ADD_EXTRUSION_RATE  
  #ifdef PID_ADD_EXTRUSION_RATE
    #define  DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
  #endif
#endif // PIDTEMP

//  extruder run-out prevention. 
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
//#define EXTRUDER_RUNOUT_PREVENT  
#define EXTRUDER_RUNOUT_MINTEMP 190  
#define EXTRUDER_RUNOUT_SECONDS 30.
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
#define EXTRUDER_RUNOUT_SPEED 1500.  //extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100


//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================


// Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors

// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false

#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing

// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruders

// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruders
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.

// Inverting axis direction
//#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
//#define INVERT_Y_DIR true   // for Mendel set to true, for Orca set to false
//#define INVERT_Z_DIR false    // for Mendel set to false, for Orca set to true
//#define INVERT_E*_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders

#define INVERT_X_DIR true    // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false    // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false

//// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1

#define min_software_endstops true //If true, axis won't move to coordinates less than zero.
#define max_software_endstops true  //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 205
#define Y_MAX_LENGTH 205
#define Z_MAX_LENGTH 200

//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0}  // set the homing speeds (mm/min)

//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
#define X_HOME_RETRACT_MM 5 
#define Y_HOME_RETRACT_MM 5 
#define Z_HOME_RETRACT_MM 1 
#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.

#define AXIS_RELATIVE_MODES {false, false, false, false}

#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)

// default settings 

#define DEFAULT_AXIS_STEPS_PER_UNIT   {78.7402,78.7402,200*8/3,760*1.1}                    // default steps per unit for ultimaker 
//#define DEFAULT_AXIS_STEPS_PER_UNIT   {40, 40, 3333.92, 360} //sells mendel with v9 extruder
//#define DEFAULT_AXIS_STEPS_PER_UNIT   {80.3232, 80.8900, 2284.7651, 757.2218} // SAE Prusa w/ Wade extruder
#define DEFAULT_MAX_FEEDRATE          {500, 500, 5, 45}    // (mm/sec)    
#define DEFAULT_MAX_ACCELERATION      {9000,9000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves 
#define DEFAULT_RETRACT_ACCELERATION  3000   // X, Y, Z and E max acceleration in mm/s^2 for r retracts

#define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
#define DEFAULT_MINTRAVELFEEDRATE     0.0

// minimum time in microseconds that a movement needs to take if the buffer is emptied.   Increase this number if you see blobs while printing high speed & high detail.  It will slowdown on the detailed stuff.
#define DEFAULT_MINSEGMENTTIME        20000   // Obsolete delete this
#define DEFAULT_XYJERK                20.0    // (mm/sec)
#define DEFAULT_ZJERK                 0.4     // (mm/sec)

// If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN

//default stepper release if idle
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E"  //z stays  powered


//===========================================================================
//=============================Additional Features===========================
//===========================================================================

// EEPROM
// the microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).  
// M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support
#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can.
#define EEPROM_CHITCHAT


// The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However:
// the Watchdog is not working well, so please only enable this for testing
// this enables the watchdog interrupt.
//#define USE_WATCHDOG
//#ifdef USE_WATCHDOG
  // you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
//#define RESET_MANUAL
//#define WATCHDOG_TIMEOUT 4  //seconds
//#endif

// extruder advance constant (s2/mm3)
//
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
//
// hooke's law says:		force = k * distance
// bernoulli's priniciple says:	v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE

#ifdef ADVANCE
  #define EXTRUDER_ADVANCE_K .0

  #define D_FILAMENT 2.85
  #define STEPS_MM_E 836
  #define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
  #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)

#endif // ADVANCE


//LCD and SD support
//#define ULTRA_LCD  //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
#define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.

//#define ULTIPANEL
#ifdef ULTIPANEL
  //#define NEWPANEL  //enable this if you have a click-encoder panel
  #define SDSUPPORT
  #define ULTRA_LCD
  #define LCD_WIDTH 20
  #define LCD_HEIGHT 4
#else //no panel but just lcd 
  #ifdef ULTRA_LCD
    #define LCD_WIDTH 16
    #define LCD_HEIGHT 2
  #endif
#endif

// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
//#define DEBUG_STEPS


// Arc interpretation settings:
#define MM_PER_ARC_SEGMENT 1
#define N_ARC_CORRECTION 25


//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
//The maximum buffered steps/sec of the extruder motor are called "se".
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
// you exit the value by any M109 without F*
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
// on an ultimaker, some initial testing worked with M109 S215 T260 F0.1 in the start.gcode
//#define AUTOTEMP
#ifdef AUTOTEMP
  #define AUTOTEMP_OLDWEIGHT 0.98
#endif

//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
#define PREVENT_DANGEROUS_EXTRUDE
#define EXTRUDE_MINTEMP 190
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.

const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement


// M240  Triggers a camera by emulating a Canon RC-1 Remote
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN     23

//===========================================================================
//=============================Buffers           ============================
//===========================================================================



// The number of linear motions that can be in the plan at any give time.  
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
#if defined SDSUPPORT
  #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
  #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif


//The ASCII buffer for recieving from the serial:
#define MAX_CMD_SIZE 96
#define BUFSIZE 4


#include "thermistortables.h"

#endif //__CONFIGURATION_H