My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 53KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. /**
  40. *
  41. * ***********************************
  42. * ** ATTENTION TO ALL DEVELOPERS **
  43. * ***********************************
  44. *
  45. * You must increment this version number for every significant change such as,
  46. * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
  47. *
  48. * Note: Update also Version.h !
  49. */
  50. #define CONFIGURATION_H_VERSION 010100
  51. //===========================================================================
  52. //============================= Getting Started =============================
  53. //===========================================================================
  54. /**
  55. * Here are some standard links for getting your machine calibrated:
  56. *
  57. * http://reprap.org/wiki/Calibration
  58. * http://youtu.be/wAL9d7FgInk
  59. * http://calculator.josefprusa.cz
  60. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  61. * http://www.thingiverse.com/thing:5573
  62. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  63. * http://www.thingiverse.com/thing:298812
  64. */
  65. //===========================================================================
  66. //============================= DELTA Printer ===============================
  67. //===========================================================================
  68. // For a Delta printer replace the configuration files with the files in the
  69. // example_configurations/delta directory.
  70. //
  71. //===========================================================================
  72. //============================= SCARA Printer ===============================
  73. //===========================================================================
  74. // For a Scara printer replace the configuration files with the files in the
  75. // example_configurations/SCARA directory.
  76. //
  77. // @section info
  78. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  79. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  80. // build by the user have been successfully uploaded into firmware.
  81. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  82. #define SHOW_BOOTSCREEN
  83. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  84. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  85. //
  86. // *** VENDORS PLEASE READ *****************************************************
  87. //
  88. // Marlin now allow you to have a vendor boot image to be displayed on machine
  89. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  90. // custom boot image and them the default Marlin boot image is shown.
  91. //
  92. // We suggest for you to take advantage of this new feature and keep the Marlin
  93. // boot image unmodified. For an example have a look at the bq Hephestos 2
  94. // example configuration folder.
  95. //
  96. //#define SHOW_CUSTOM_BOOTSCREEN
  97. // @section machine
  98. /**
  99. * Select which serial port on the board will be used for communication with the host.
  100. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  101. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  102. *
  103. * :[0,1,2,3,4,5,6,7]
  104. */
  105. #define SERIAL_PORT 0
  106. #define BAUDRATE 250000
  107. /**
  108. * This setting determines the communication speed of the printer.
  109. *
  110. * 250000 works in most cases, but you might try a lower speed if
  111. * you commonly experience drop-outs during host printing.
  112. *
  113. * :[2400,9600,19200,38400,57600,115200,250000]
  114. */
  115. // Enable the Bluetooth serial interface on AT90USB devices
  116. //#define BLUETOOTH
  117. // The following define selects which electronics board you have.
  118. // Please choose the name from boards.h that matches your setup
  119. #ifndef MOTHERBOARD
  120. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  121. #endif
  122. // Optional custom name for your RepStrap or other custom machine
  123. // Displayed in the LCD "Ready" message
  124. //#define CUSTOM_MACHINE_NAME "3D Printer"
  125. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  126. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  127. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  128. // This defines the number of extruders
  129. // :[1,2,3,4]
  130. #define EXTRUDERS 1
  131. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  132. //#define SINGLENOZZLE
  133. // A dual extruder that uses a single stepper motor
  134. // Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z
  135. //#define SWITCHING_EXTRUDER
  136. #if ENABLED(SWITCHING_EXTRUDER)
  137. #define SWITCHING_EXTRUDER_SERVO_NR 0
  138. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  139. //#define HOTEND_OFFSET_Z {0.0, 0.0}
  140. #endif
  141. /**
  142. * "Mixing Extruder"
  143. * - Adds a new code, M165, to set the current mix factors.
  144. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  145. * - Optional support for Repetier Host M163, M164, and virtual extruder.
  146. * - This implementation supports only a single extruder.
  147. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  148. */
  149. //#define MIXING_EXTRUDER
  150. #if ENABLED(MIXING_EXTRUDER)
  151. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  152. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  153. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  154. #endif
  155. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  156. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  157. // For the other hotends it is their distance from the extruder 0 hotend.
  158. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  159. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  160. /**
  161. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  162. *
  163. * 0 = No Power Switch
  164. * 1 = ATX
  165. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  166. *
  167. * :{0:'No power switch',1:'ATX',2:'X-Box 360'}
  168. */
  169. #define POWER_SUPPLY 0
  170. #if POWER_SUPPLY > 0
  171. // Enable this option to leave the PSU off at startup.
  172. // Power to steppers and heaters will need to be turned on with M80.
  173. //#define PS_DEFAULT_OFF
  174. #endif
  175. // @section temperature
  176. //===========================================================================
  177. //============================= Thermal Settings ============================
  178. //===========================================================================
  179. //
  180. //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  181. //
  182. //// Temperature sensor settings:
  183. // -3 is thermocouple with MAX31855 (only for sensor 0)
  184. // -2 is thermocouple with MAX6675 (only for sensor 0)
  185. // -1 is thermocouple with AD595
  186. // 0 is not used
  187. // 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  188. // 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  189. // 3 is Mendel-parts thermistor (4.7k pullup)
  190. // 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  191. // 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  192. // 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  193. // 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  194. // 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  195. // 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  196. // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  197. // 10 is 100k RS thermistor 198-961 (4.7k pullup)
  198. // 11 is 100k beta 3950 1% thermistor (4.7k pullup)
  199. // 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  200. // 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  201. // 20 is the PT100 circuit found in the Ultimainboard V2.x
  202. // 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  203. // 66 is 4.7M High Temperature thermistor from Dyze Design
  204. // 70 is the 100K thermistor found in the bq Hephestos 2
  205. //
  206. // 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
  207. // (but gives greater accuracy and more stable PID)
  208. // 51 is 100k thermistor - EPCOS (1k pullup)
  209. // 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  210. // 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  211. //
  212. // 1047 is Pt1000 with 4k7 pullup
  213. // 1010 is Pt1000 with 1k pullup (non standard)
  214. // 147 is Pt100 with 4k7 pullup
  215. // 110 is Pt100 with 1k pullup (non standard)
  216. // 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
  217. // Use it for Testing or Development purposes. NEVER for production machine.
  218. //#define DUMMY_THERMISTOR_998_VALUE 25
  219. //#define DUMMY_THERMISTOR_999_VALUE 100
  220. // :{ '0': "Not used",'1':"100k / 4.7k - EPCOS",'2':"200k / 4.7k - ATC Semitec 204GT-2",'3':"Mendel-parts / 4.7k",'4':"10k !! do not use for a hotend. Bad resolution at high temp. !!",'5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)",'6':"100k / 4.7k EPCOS - Not as accurate as Table 1",'7':"100k / 4.7k Honeywell 135-104LAG-J01",'8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT",'9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1",'10':"100k / 4.7k RS 198-961",'11':"100k / 4.7k beta 3950 1%",'12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)",'13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'",'20':"PT100 (Ultimainboard V2.x)",'51':"100k / 1k - EPCOS",'52':"200k / 1k - ATC Semitec 204GT-2",'55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)",'60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950",'66':"Dyze Design 4.7M High Temperature thermistor",'70':"the 100K thermistor found in the bq Hephestos 2",'71':"100k / 4.7k Honeywell 135-104LAF-J01",'147':"Pt100 / 4.7k",'1047':"Pt1000 / 4.7k",'110':"Pt100 / 1k (non-standard)",'1010':"Pt1000 / 1k (non standard)",'-3':"Thermocouple + MAX31855 (only for sensor 0)",'-2':"Thermocouple + MAX6675 (only for sensor 0)",'-1':"Thermocouple + AD595",'998':"Dummy 1",'999':"Dummy 2" }
  221. #define TEMP_SENSOR_0 1
  222. #define TEMP_SENSOR_1 0
  223. #define TEMP_SENSOR_2 0
  224. #define TEMP_SENSOR_3 0
  225. #define TEMP_SENSOR_BED 0
  226. // This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
  227. //#define TEMP_SENSOR_1_AS_REDUNDANT
  228. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  229. // Extruder temperature must be close to target for this long before M109 returns success
  230. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  231. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  232. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  233. // Bed temperature must be close to target for this long before M190 returns success
  234. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  235. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  236. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  237. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  238. // to check that the wiring to the thermistor is not broken.
  239. // Otherwise this would lead to the heater being powered on all the time.
  240. #define HEATER_0_MINTEMP 5
  241. #define HEATER_1_MINTEMP 5
  242. #define HEATER_2_MINTEMP 5
  243. #define HEATER_3_MINTEMP 5
  244. #define BED_MINTEMP 5
  245. // When temperature exceeds max temp, your heater will be switched off.
  246. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  247. // You should use MINTEMP for thermistor short/failure protection.
  248. #define HEATER_0_MAXTEMP 275
  249. #define HEATER_1_MAXTEMP 275
  250. #define HEATER_2_MAXTEMP 275
  251. #define HEATER_3_MAXTEMP 275
  252. #define BED_MAXTEMP 150
  253. //===========================================================================
  254. //============================= PID Settings ================================
  255. //===========================================================================
  256. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  257. // Comment the following line to disable PID and enable bang-bang.
  258. #define PIDTEMP
  259. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  260. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  261. #if ENABLED(PIDTEMP)
  262. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  263. //#define PID_DEBUG // Sends debug data to the serial port.
  264. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  265. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  266. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  267. // Set/get with gcode: M301 E[extruder number, 0-2]
  268. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  269. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  270. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
  271. #define K1 0.95 //smoothing factor within the PID
  272. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  273. // Ultimaker
  274. #define DEFAULT_Kp 22.2
  275. #define DEFAULT_Ki 1.08
  276. #define DEFAULT_Kd 114
  277. // MakerGear
  278. //#define DEFAULT_Kp 7.0
  279. //#define DEFAULT_Ki 0.1
  280. //#define DEFAULT_Kd 12
  281. // Mendel Parts V9 on 12V
  282. //#define DEFAULT_Kp 63.0
  283. //#define DEFAULT_Ki 2.25
  284. //#define DEFAULT_Kd 440
  285. #endif // PIDTEMP
  286. //===========================================================================
  287. //============================= PID > Bed Temperature Control ===============
  288. //===========================================================================
  289. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  290. //
  291. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  292. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  293. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  294. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  295. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  296. // shouldn't use bed PID until someone else verifies your hardware works.
  297. // If this is enabled, find your own PID constants below.
  298. //#define PIDTEMPBED
  299. //#define BED_LIMIT_SWITCHING
  300. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  301. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  302. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  303. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  304. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  305. #if ENABLED(PIDTEMPBED)
  306. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  307. #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
  308. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  309. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  310. #define DEFAULT_bedKp 10.00
  311. #define DEFAULT_bedKi .023
  312. #define DEFAULT_bedKd 305.4
  313. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  314. //from pidautotune
  315. //#define DEFAULT_bedKp 97.1
  316. //#define DEFAULT_bedKi 1.41
  317. //#define DEFAULT_bedKd 1675.16
  318. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  319. #endif // PIDTEMPBED
  320. // @section extruder
  321. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  322. // It also enables the M302 command to set the minimum extrusion temperature
  323. // or to allow moving the extruder regardless of the hotend temperature.
  324. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  325. #define PREVENT_COLD_EXTRUSION
  326. #define EXTRUDE_MINTEMP 170
  327. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  328. // Note that for Bowden Extruders a too-small value here may prevent loading.
  329. #define PREVENT_LENGTHY_EXTRUDE
  330. #define EXTRUDE_MAXLENGTH 200
  331. //===========================================================================
  332. //======================== Thermal Runaway Protection =======================
  333. //===========================================================================
  334. /**
  335. * Thermal Protection protects your printer from damage and fire if a
  336. * thermistor falls out or temperature sensors fail in any way.
  337. *
  338. * The issue: If a thermistor falls out or a temperature sensor fails,
  339. * Marlin can no longer sense the actual temperature. Since a disconnected
  340. * thermistor reads as a low temperature, the firmware will keep the heater on.
  341. *
  342. * If you get "Thermal Runaway" or "Heating failed" errors the
  343. * details can be tuned in Configuration_adv.h
  344. */
  345. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  346. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  347. //===========================================================================
  348. //============================= Mechanical Settings =========================
  349. //===========================================================================
  350. // @section machine
  351. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  352. //#define COREXY
  353. //#define COREXZ
  354. //#define COREYZ
  355. // Enable this option for Toshiba steppers
  356. //#define CONFIG_STEPPERS_TOSHIBA
  357. //===========================================================================
  358. //============================== Endstop Settings ===========================
  359. //===========================================================================
  360. // @section homing
  361. // Specify here all the endstop connectors that are connected to any endstop or probe.
  362. // Almost all printers will be using one per axis. Probes will use one or more of the
  363. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  364. #define USE_XMIN_PLUG
  365. #define USE_YMIN_PLUG
  366. #define USE_ZMIN_PLUG
  367. //#define USE_XMAX_PLUG
  368. //#define USE_YMAX_PLUG
  369. //#define USE_ZMAX_PLUG
  370. // coarse Endstop Settings
  371. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  372. #if DISABLED(ENDSTOPPULLUPS)
  373. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  374. //#define ENDSTOPPULLUP_XMAX
  375. //#define ENDSTOPPULLUP_YMAX
  376. //#define ENDSTOPPULLUP_ZMAX
  377. //#define ENDSTOPPULLUP_XMIN
  378. //#define ENDSTOPPULLUP_YMIN
  379. //#define ENDSTOPPULLUP_ZMIN
  380. //#define ENDSTOPPULLUP_ZMIN_PROBE
  381. #endif
  382. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  383. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  384. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  385. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  386. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  387. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  388. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  389. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  390. //=============================================================================
  391. //============================== Movement Settings ============================
  392. //=============================================================================
  393. // @section motion
  394. /**
  395. * Default Settings
  396. *
  397. * These settings can be reset by M502
  398. *
  399. * Note that if EEPROM is enabled, saved values will override these.
  400. */
  401. /**
  402. * Default Axis Steps Per Unit (steps/mm)
  403. * Override with M92
  404. */
  405. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  406. /**
  407. * Default Max Feed Rate (mm/s)
  408. * Override with M203
  409. */
  410. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  411. /**
  412. * Default Max Acceleration (change/s) change = mm/s
  413. * Override with M201
  414. *
  415. * Maximum start speed for accelerated moves: { X, Y, Z, E }
  416. */
  417. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  418. /**
  419. * Default Acceleration (change/s) change = mm/s
  420. * Override with M204
  421. *
  422. * M204 P Acceleration
  423. * M204 R Retract Acceleration
  424. * M204 T Travel Acceleration
  425. */
  426. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  427. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  428. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  429. /**
  430. * Defult Jerk (mm/s)
  431. *
  432. * "Jerk" specifies the minimum speed change that requires acceleration.
  433. * When changing speed and direction, if the difference is less than the
  434. * value set here, it may happen instantaneously.
  435. */
  436. #define DEFAULT_XYJERK 20.0
  437. #define DEFAULT_ZJERK 0.4
  438. #define DEFAULT_EJERK 5.0
  439. //===========================================================================
  440. //============================= Z Probe Options =============================
  441. //===========================================================================
  442. // @section probes
  443. //
  444. // Probe Type
  445. // Probes are sensors/switches that are activated / deactivated before/after use.
  446. //
  447. // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  448. // You must activate one of these to use AUTO_BED_LEVELING_FEATURE below.
  449. //
  450. // Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
  451. //
  452. // A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  453. // For example an inductive probe, or a setup that uses the nozzle to probe.
  454. // An inductive probe must be deactivated to go below
  455. // its trigger-point if hardware endstops are active.
  456. //#define FIX_MOUNTED_PROBE
  457. // The BLTouch probe emulates a servo probe.
  458. // The default connector is SERVO 0. Set Z_ENDSTOP_SERVO_NR below to override.
  459. //#define BLTOUCH
  460. // Z Servo Probe, such as an endstop switch on a rotating arm.
  461. //#define Z_ENDSTOP_SERVO_NR 0
  462. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  463. // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
  464. //#define Z_PROBE_SLED
  465. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  466. // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  467. // X and Y offsets must be integers.
  468. //
  469. // In the following example the X and Y offsets are both positive:
  470. // #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  471. // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  472. //
  473. // +-- BACK ---+
  474. // | |
  475. // L | (+) P | R <-- probe (20,20)
  476. // E | | I
  477. // F | (-) N (+) | G <-- nozzle (10,10)
  478. // T | | H
  479. // | (-) | T
  480. // | |
  481. // O-- FRONT --+
  482. // (0,0)
  483. #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
  484. #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
  485. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
  486. // X and Y axis travel speed (mm/m) between probes
  487. #define XY_PROBE_SPEED 8000
  488. // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
  489. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  490. // Speed for the "accurate" probe of each point
  491. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  492. // Use double touch for probing
  493. //#define PROBE_DOUBLE_TOUCH
  494. //
  495. // Allen Key Probe is defined in the Delta example configurations.
  496. //
  497. // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
  498. //
  499. // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
  500. // Example: To park the head outside the bed area when homing with G28.
  501. //
  502. // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
  503. //
  504. // For a servo-based Z probe, you must set up servo support below, including
  505. // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
  506. //
  507. // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
  508. // - Use 5V for powered (usu. inductive) sensors.
  509. // - Otherwise connect:
  510. // - normally-closed switches to GND and D32.
  511. // - normally-open switches to 5V and D32.
  512. //
  513. // Normally-closed switches are advised and are the default.
  514. //
  515. //
  516. // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
  517. // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
  518. // default pin for all RAMPS-based boards. Most boards use the X_MAX_PIN by default.
  519. // To use a different pin you can override it here.
  520. //
  521. // WARNING:
  522. // Setting the wrong pin may have unexpected and potentially disastrous consequences.
  523. // Use with caution and do your homework.
  524. //
  525. //#define Z_MIN_PROBE_PIN X_MAX_PIN
  526. //
  527. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
  528. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
  529. //
  530. //#define Z_MIN_PROBE_ENDSTOP
  531. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
  532. // The Z_MIN_PIN will then be used for both Z-homing and probing.
  533. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  534. // To use a probe you must enable one of the two options above!
  535. // Enable Z Probe Repeatability test to see how accurate your probe is
  536. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  537. /**
  538. * Z probes require clearance when deploying, stowing, and moving between
  539. * probe points to avoid hitting the bed and other hardware.
  540. * Servo-mounted probes require extra space for the arm to rotate.
  541. * Inductive probes need space to keep from triggering early.
  542. *
  543. * Use these settings to specify the distance (mm) to raise the probe (or
  544. * lower the bed). The values set here apply over and above any (negative)
  545. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  546. * Only integer values >= 1 are valid here.
  547. *
  548. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  549. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  550. */
  551. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  552. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  553. //
  554. // For M851 give a range for adjusting the Z probe offset
  555. //
  556. #define Z_PROBE_OFFSET_RANGE_MIN -20
  557. #define Z_PROBE_OFFSET_RANGE_MAX 20
  558. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  559. // :{0:'Low',1:'High'}
  560. #define X_ENABLE_ON 0
  561. #define Y_ENABLE_ON 0
  562. #define Z_ENABLE_ON 0
  563. #define E_ENABLE_ON 0 // For all extruders
  564. // Disables axis stepper immediately when it's not being used.
  565. // WARNING: When motors turn off there is a chance of losing position accuracy!
  566. #define DISABLE_X false
  567. #define DISABLE_Y false
  568. #define DISABLE_Z false
  569. // Warn on display about possibly reduced accuracy
  570. //#define DISABLE_REDUCED_ACCURACY_WARNING
  571. // @section extruder
  572. #define DISABLE_E false // For all extruders
  573. #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
  574. // @section machine
  575. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  576. #define INVERT_X_DIR false
  577. #define INVERT_Y_DIR true
  578. #define INVERT_Z_DIR false
  579. // @section extruder
  580. // For direct drive extruder v9 set to true, for geared extruder set to false.
  581. #define INVERT_E0_DIR false
  582. #define INVERT_E1_DIR false
  583. #define INVERT_E2_DIR false
  584. #define INVERT_E3_DIR false
  585. // @section homing
  586. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  587. // Be sure you have this distance over your Z_MAX_POS in case.
  588. // ENDSTOP SETTINGS:
  589. // Sets direction of endstops when homing; 1=MAX, -1=MIN
  590. // :[-1,1]
  591. #define X_HOME_DIR -1
  592. #define Y_HOME_DIR -1
  593. #define Z_HOME_DIR -1
  594. #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
  595. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
  596. // @section machine
  597. // Travel limits after homing (units are in mm)
  598. #define X_MIN_POS 0
  599. #define Y_MIN_POS 0
  600. #define Z_MIN_POS 0
  601. #define X_MAX_POS 200
  602. #define Y_MAX_POS 200
  603. #define Z_MAX_POS 200
  604. //===========================================================================
  605. //========================= Filament Runout Sensor ==========================
  606. //===========================================================================
  607. //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
  608. // RAMPS-based boards use SERVO3_PIN. For other boards you may need to define FIL_RUNOUT_PIN.
  609. // It is assumed that when logic high = filament available
  610. // when logic low = filament ran out
  611. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  612. const bool FIL_RUNOUT_INVERTING = false; // set to true to invert the logic of the sensor.
  613. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  614. #define FILAMENT_RUNOUT_SCRIPT "M600"
  615. #endif
  616. //===========================================================================
  617. //============================ Mesh Bed Leveling ============================
  618. //===========================================================================
  619. //#define MESH_BED_LEVELING // Enable mesh bed leveling.
  620. #if ENABLED(MESH_BED_LEVELING)
  621. #define MESH_INSET 10 // Mesh inset margin on print area
  622. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
  623. #define MESH_NUM_Y_POINTS 3
  624. #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
  625. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
  626. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
  627. #if ENABLED(MANUAL_BED_LEVELING)
  628. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  629. #endif // MANUAL_BED_LEVELING
  630. #endif // MESH_BED_LEVELING
  631. //===========================================================================
  632. //============================ Bed Auto Leveling ============================
  633. //===========================================================================
  634. // @section bedlevel
  635. //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
  636. // Enable this feature to get detailed logging of G28, G29, M48, etc.
  637. // Logging is off by default. Enable this logging feature with 'M111 S32'.
  638. // NOTE: Requires a huge amount of PROGMEM.
  639. //#define DEBUG_LEVELING_FEATURE
  640. #if ENABLED(AUTO_BED_LEVELING_FEATURE)
  641. // There are 2 different ways to specify probing locations:
  642. //
  643. // - "grid" mode
  644. // Probe several points in a rectangular grid.
  645. // You specify the rectangle and the density of sample points.
  646. // This mode is preferred because there are more measurements.
  647. //
  648. // - "3-point" mode
  649. // Probe 3 arbitrary points on the bed (that aren't collinear)
  650. // You specify the XY coordinates of all 3 points.
  651. // Enable this to sample the bed in a grid (least squares solution).
  652. // Note: this feature generates 10KB extra code size.
  653. #define AUTO_BED_LEVELING_GRID
  654. #if ENABLED(AUTO_BED_LEVELING_GRID)
  655. #define LEFT_PROBE_BED_POSITION 15
  656. #define RIGHT_PROBE_BED_POSITION 170
  657. #define FRONT_PROBE_BED_POSITION 20
  658. #define BACK_PROBE_BED_POSITION 170
  659. #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
  660. // Set the number of grid points per dimension.
  661. // You probably don't need more than 3 (squared=9).
  662. #define ABL_GRID_POINTS_X 3
  663. #define ABL_GRID_POINTS_Y ABL_GRID_POINTS_X
  664. #else // !AUTO_BED_LEVELING_GRID
  665. // Arbitrary points to probe.
  666. // A simple cross-product is used to estimate the plane of the bed.
  667. #define ABL_PROBE_PT_1_X 15
  668. #define ABL_PROBE_PT_1_Y 180
  669. #define ABL_PROBE_PT_2_X 15
  670. #define ABL_PROBE_PT_2_Y 20
  671. #define ABL_PROBE_PT_3_X 170
  672. #define ABL_PROBE_PT_3_Y 20
  673. #endif // !AUTO_BED_LEVELING_GRID
  674. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
  675. // Useful to retract a deployable Z probe.
  676. // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
  677. // it is highly recommended you also enable Z_SAFE_HOMING below!
  678. #endif // AUTO_BED_LEVELING_FEATURE
  679. // @section homing
  680. // The center of the bed is at (X=0, Y=0)
  681. //#define BED_CENTER_AT_0_0
  682. // Manually set the home position. Leave these undefined for automatic settings.
  683. // For DELTA this is the top-center of the Cartesian print volume.
  684. //#define MANUAL_X_HOME_POS 0
  685. //#define MANUAL_Y_HOME_POS 0
  686. //#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
  687. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  688. //
  689. // With this feature enabled:
  690. //
  691. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  692. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  693. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  694. // - Prevent Z homing when the Z probe is outside bed area.
  695. //#define Z_SAFE_HOMING
  696. #if ENABLED(Z_SAFE_HOMING)
  697. #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
  698. #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
  699. #endif
  700. // Homing speeds (mm/m)
  701. #define HOMING_FEEDRATE_XY (50*60)
  702. #define HOMING_FEEDRATE_Z (4*60)
  703. //=============================================================================
  704. //============================= Additional Features ===========================
  705. //=============================================================================
  706. // @section extras
  707. //
  708. // EEPROM
  709. //
  710. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  711. // M500 - stores parameters in EEPROM
  712. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  713. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  714. //define this to enable EEPROM support
  715. //#define EEPROM_SETTINGS
  716. #if ENABLED(EEPROM_SETTINGS)
  717. // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
  718. #define EEPROM_CHITCHAT // Please keep turned on if you can.
  719. #endif
  720. //
  721. // Host Keepalive
  722. //
  723. // When enabled Marlin will send a busy status message to the host
  724. // every couple of seconds when it can't accept commands.
  725. //
  726. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  727. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  728. //
  729. // M100 Free Memory Watcher
  730. //
  731. //#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
  732. //
  733. // G20/G21 Inch mode support
  734. //
  735. //#define INCH_MODE_SUPPORT
  736. //
  737. // M149 Set temperature units support
  738. //
  739. //#define TEMPERATURE_UNITS_SUPPORT
  740. // @section temperature
  741. // Preheat Constants
  742. #define PREHEAT_1_TEMP_HOTEND 180
  743. #define PREHEAT_1_TEMP_BED 70
  744. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  745. #define PREHEAT_2_TEMP_HOTEND 240
  746. #define PREHEAT_2_TEMP_BED 110
  747. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  748. //
  749. // Nozzle Park -- EXPERIMENTAL
  750. //
  751. // When enabled allows the user to define a special XYZ position, inside the
  752. // machine's topology, to park the nozzle when idle or when receiving the G27
  753. // command.
  754. //
  755. // The "P" paramenter controls what is the action applied to the Z axis:
  756. // P0: (Default) If current Z-pos is lower than Z-park then the nozzle will
  757. // be raised to reach Z-park height.
  758. //
  759. // P1: No matter the current Z-pos, the nozzle will be raised/lowered to
  760. // reach Z-park height.
  761. //
  762. // P2: The nozzle height will be raised by Z-park amount but never going over
  763. // the machine's limit of Z_MAX_POS.
  764. //
  765. //#define NOZZLE_PARK_FEATURE
  766. #if ENABLED(NOZZLE_PARK_FEATURE)
  767. // Specify a park position as { X, Y, Z }
  768. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  769. #endif
  770. //
  771. // Clean Nozzle Feature -- EXPERIMENTAL
  772. //
  773. // When enabled allows the user to send G12 to start the nozzle cleaning
  774. // process, the G-Code accepts two parameters:
  775. // "P" for pattern selection
  776. // "S" for defining the number of strokes/repetitions
  777. //
  778. // Available list of patterns:
  779. // P0: This is the default pattern, this process requires a sponge type
  780. // material at a fixed bed location, the cleaning process is based on
  781. // "strokes" i.e. back-and-forth movements between the starting and end
  782. // points.
  783. //
  784. // P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T"
  785. // defines the number of zig-zag triangles to be done. "S" defines the
  786. // number of strokes aka one back-and-forth movement. As an example
  787. // sending "G12 P1 S1 T3" will execute:
  788. //
  789. // --
  790. // | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  791. // | | / \ / \ / \ |
  792. // A | | / \ / \ / \ |
  793. // | | / \ / \ / \ |
  794. // | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  795. // -- +--------------------------------+
  796. // |________|_________|_________|
  797. // T1 T2 T3
  798. //
  799. // Caveats: End point Z should use the same value as Start point Z.
  800. //
  801. // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
  802. // may change to add new functionality like different wipe patterns.
  803. //
  804. //#define NOZZLE_CLEAN_FEATURE
  805. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  806. // Number of pattern repetitions
  807. #define NOZZLE_CLEAN_STROKES 12
  808. // Specify positions as { X, Y, Z }
  809. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  810. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  811. // Moves the nozzle to the initial position
  812. #define NOZZLE_CLEAN_GOBACK
  813. #endif
  814. //
  815. // Print job timer
  816. //
  817. // Enable this option to automatically start and stop the
  818. // print job timer when M104/M109/M190 commands are received.
  819. // M104 (extruder without wait) - high temp = none, low temp = stop timer
  820. // M109 (extruder with wait) - high temp = start timer, low temp = stop timer
  821. // M190 (bed with wait) - high temp = start timer, low temp = none
  822. //
  823. // In all cases the timer can be started and stopped using
  824. // the following commands:
  825. //
  826. // - M75 - Start the print job timer
  827. // - M76 - Pause the print job timer
  828. // - M77 - Stop the print job timer
  829. #define PRINTJOB_TIMER_AUTOSTART
  830. //
  831. // Print Counter
  832. //
  833. // When enabled Marlin will keep track of some print statistical data such as:
  834. // - Total print jobs
  835. // - Total successful print jobs
  836. // - Total failed print jobs
  837. // - Total time printing
  838. //
  839. // This information can be viewed by the M78 command.
  840. //#define PRINTCOUNTER
  841. //=============================================================================
  842. //============================= LCD and SD support ============================
  843. //=============================================================================
  844. // @section lcd
  845. //
  846. // LCD LANGUAGE
  847. //
  848. // Here you may choose the language used by Marlin on the LCD menus, the following
  849. // list of languages are available:
  850. // en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
  851. // kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, test
  852. //
  853. // :{'en':'English','an':'Aragonese','bg':'Bulgarian','ca':'Catalan','cn':'Chinese','cz':'Czech','de':'German','el':'Greek','el-gr':'Greek (Greece)','es':'Spanish','eu':'Basque-Euskera','fi':'Finnish','fr':'French','gl':'Galician','hr':'Croatian','it':'Italian','kana':'Japanese','kana_utf8':'Japanese (UTF8)','nl':'Dutch','pl':'Polish','pt':'Portuguese','pt-br':'Portuguese (Brazilian)','pt-br_utf8':'Portuguese (Brazilian UTF8)','pt_utf8':'Portuguese (UTF8)','ru':'Russian','test':'TEST'}
  854. //
  855. #define LCD_LANGUAGE en
  856. //
  857. // LCD Character Set
  858. //
  859. // Note: This option is NOT applicable to Graphical Displays.
  860. //
  861. // All character-based LCD's provide ASCII plus one of these
  862. // language extensions:
  863. //
  864. // - JAPANESE ... the most common
  865. // - WESTERN ... with more accented characters
  866. // - CYRILLIC ... for the Russian language
  867. //
  868. // To determine the language extension installed on your controller:
  869. //
  870. // - Compile and upload with LCD_LANGUAGE set to 'test'
  871. // - Click the controller to view the LCD menu
  872. // - The LCD will display Japanese, Western, or Cyrillic text
  873. //
  874. // See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
  875. //
  876. // :['JAPANESE','WESTERN','CYRILLIC']
  877. //
  878. #define DISPLAY_CHARSET_HD44780 JAPANESE
  879. //
  880. // LCD TYPE
  881. //
  882. // You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
  883. // 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
  884. // (ST7565R family). (This option will be set automatically for certain displays.)
  885. //
  886. // IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
  887. // https://github.com/olikraus/U8glib_Arduino
  888. //
  889. //#define ULTRA_LCD // Character based
  890. //#define DOGLCD // Full graphics display
  891. //
  892. // SD CARD
  893. //
  894. // SD Card support is disabled by default. If your controller has an SD slot,
  895. // you must uncomment the following option or it won't work.
  896. //
  897. //#define SDSUPPORT
  898. //
  899. // SD CARD: SPI SPEED
  900. //
  901. // Uncomment ONE of the following items to use a slower SPI transfer
  902. // speed. This is usually required if you're getting volume init errors.
  903. //
  904. //#define SPI_SPEED SPI_HALF_SPEED
  905. //#define SPI_SPEED SPI_QUARTER_SPEED
  906. //#define SPI_SPEED SPI_EIGHTH_SPEED
  907. //
  908. // SD CARD: ENABLE CRC
  909. //
  910. // Use CRC checks and retries on the SD communication.
  911. //
  912. //#define SD_CHECK_AND_RETRY
  913. //
  914. // ENCODER SETTINGS
  915. //
  916. // This option overrides the default number of encoder pulses needed to
  917. // produce one step. Should be increased for high-resolution encoders.
  918. //
  919. //#define ENCODER_PULSES_PER_STEP 1
  920. //
  921. // Use this option to override the number of step signals required to
  922. // move between next/prev menu items.
  923. //
  924. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  925. /**
  926. * Encoder Direction Options
  927. *
  928. * Test your encoder's behavior first with both options disabled.
  929. *
  930. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  931. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  932. * Reversed Value Editing only? Enable BOTH options.
  933. */
  934. //
  935. // This option reverses the encoder direction everywhere
  936. //
  937. // Set this option if CLOCKWISE causes values to DECREASE
  938. //
  939. //#define REVERSE_ENCODER_DIRECTION
  940. //
  941. // This option reverses the encoder direction for navigating LCD menus.
  942. //
  943. // If CLOCKWISE normally moves DOWN this makes it go UP.
  944. // If CLOCKWISE normally moves UP this makes it go DOWN.
  945. //
  946. //#define REVERSE_MENU_DIRECTION
  947. //
  948. // Individual Axis Homing
  949. //
  950. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  951. //
  952. //#define INDIVIDUAL_AXIS_HOMING_MENU
  953. //
  954. // SPEAKER/BUZZER
  955. //
  956. // If you have a speaker that can produce tones, enable it here.
  957. // By default Marlin assumes you have a buzzer with a fixed frequency.
  958. //
  959. //#define SPEAKER
  960. //
  961. // The duration and frequency for the UI feedback sound.
  962. // Set these to 0 to disable audio feedback in the LCD menus.
  963. //
  964. // Note: Test audio output with the G-Code:
  965. // M300 S<frequency Hz> P<duration ms>
  966. //
  967. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  968. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  969. //
  970. // CONTROLLER TYPE: Standard
  971. //
  972. // Marlin supports a wide variety of controllers.
  973. // Enable one of the following options to specify your controller.
  974. //
  975. //
  976. // ULTIMAKER Controller.
  977. //
  978. //#define ULTIMAKERCONTROLLER
  979. //
  980. // ULTIPANEL as seen on Thingiverse.
  981. //
  982. //#define ULTIPANEL
  983. //
  984. // Cartesio UI
  985. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  986. //
  987. //#define CARTESIO_UI
  988. //
  989. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  990. // http://reprap.org/wiki/PanelOne
  991. //
  992. //#define PANEL_ONE
  993. //
  994. // MaKr3d Makr-Panel with graphic controller and SD support.
  995. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  996. //
  997. //#define MAKRPANEL
  998. //
  999. // ReprapWorld Graphical LCD
  1000. // https://reprapworld.com/?products_details&products_id/1218
  1001. //
  1002. //#define REPRAPWORLD_GRAPHICAL_LCD
  1003. //
  1004. // Activate one of these if you have a Panucatt Devices
  1005. // Viki 2.0 or mini Viki with Graphic LCD
  1006. // http://panucatt.com
  1007. //
  1008. //#define VIKI2
  1009. //#define miniVIKI
  1010. //
  1011. // Adafruit ST7565 Full Graphic Controller.
  1012. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1013. //
  1014. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1015. //
  1016. // RepRapDiscount Smart Controller.
  1017. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1018. //
  1019. // Note: Usually sold with a white PCB.
  1020. //
  1021. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1022. //
  1023. // GADGETS3D G3D LCD/SD Controller
  1024. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1025. //
  1026. // Note: Usually sold with a blue PCB.
  1027. //
  1028. //#define G3D_PANEL
  1029. //
  1030. // RepRapDiscount FULL GRAPHIC Smart Controller
  1031. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1032. //
  1033. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1034. //
  1035. // MakerLab Mini Panel with graphic
  1036. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1037. //
  1038. //#define MINIPANEL
  1039. //
  1040. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1041. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1042. //
  1043. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1044. // is pressed, a value of 10.0 means 10mm per click.
  1045. //
  1046. //#define REPRAPWORLD_KEYPAD
  1047. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1048. //
  1049. // RigidBot Panel V1.0
  1050. // http://www.inventapart.com/
  1051. //
  1052. //#define RIGIDBOT_PANEL
  1053. //
  1054. // BQ LCD Smart Controller shipped by
  1055. // default with the BQ Hephestos 2 and Witbox 2.
  1056. //
  1057. //#define BQ_LCD_SMART_CONTROLLER
  1058. //
  1059. // CONTROLLER TYPE: I2C
  1060. //
  1061. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1062. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1063. //
  1064. //
  1065. // Elefu RA Board Control Panel
  1066. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1067. //
  1068. //#define RA_CONTROL_PANEL
  1069. //
  1070. // Sainsmart YW Robot (LCM1602) LCD Display
  1071. //
  1072. //#define LCD_I2C_SAINSMART_YWROBOT
  1073. //
  1074. // Generic LCM1602 LCD adapter
  1075. //
  1076. //#define LCM1602
  1077. //
  1078. // PANELOLU2 LCD with status LEDs,
  1079. // separate encoder and click inputs.
  1080. //
  1081. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1082. // For more info: https://github.com/lincomatic/LiquidTWI2
  1083. //
  1084. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1085. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1086. //
  1087. //#define LCD_I2C_PANELOLU2
  1088. //
  1089. // Panucatt VIKI LCD with status LEDs,
  1090. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1091. //
  1092. //#define LCD_I2C_VIKI
  1093. //
  1094. // SSD1306 OLED full graphics generic display
  1095. //
  1096. //#define U8GLIB_SSD1306
  1097. //
  1098. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1099. //
  1100. //#define SAV_3DGLCD
  1101. #if ENABLED(SAV_3DGLCD)
  1102. //#define U8GLIB_SSD1306
  1103. #define U8GLIB_SH1106
  1104. #endif
  1105. //
  1106. // CONTROLLER TYPE: Shift register panels
  1107. //
  1108. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1109. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1110. //
  1111. //#define SAV_3DLCD
  1112. //=============================================================================
  1113. //=============================== Extra Features ==============================
  1114. //=============================================================================
  1115. // @section extras
  1116. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1117. //#define FAST_PWM_FAN
  1118. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1119. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1120. // is too low, you should also increment SOFT_PWM_SCALE.
  1121. //#define FAN_SOFT_PWM
  1122. // Incrementing this by 1 will double the software PWM frequency,
  1123. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1124. // However, control resolution will be halved for each increment;
  1125. // at zero value, there are 128 effective control positions.
  1126. #define SOFT_PWM_SCALE 0
  1127. // Temperature status LEDs that display the hotend and bed temperature.
  1128. // If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
  1129. // Otherwise the RED led is on. There is 1C hysteresis.
  1130. //#define TEMP_STAT_LEDS
  1131. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1132. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1133. //#define PHOTOGRAPH_PIN 23
  1134. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1135. //#define SF_ARC_FIX
  1136. // Support for the BariCUDA Paste Extruder.
  1137. //#define BARICUDA
  1138. //define BlinkM/CyzRgb Support
  1139. //#define BLINKM
  1140. /*********************************************************************\
  1141. * R/C SERVO support
  1142. * Sponsored by TrinityLabs, Reworked by codexmas
  1143. **********************************************************************/
  1144. // Number of servos
  1145. //
  1146. // If you select a configuration below, this will receive a default value and does not need to be set manually
  1147. // set it manually if you have more servos than extruders and wish to manually control some
  1148. // leaving it undefined or defining as 0 will disable the servo subsystem
  1149. // If unsure, leave commented / disabled
  1150. //
  1151. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1152. // Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
  1153. // 300ms is a good value but you can try less delay.
  1154. // If the servo can't reach the requested position, increase it.
  1155. #define SERVO_DELAY 300
  1156. // Servo deactivation
  1157. //
  1158. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1159. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1160. /**********************************************************************\
  1161. * Support for a filament diameter sensor
  1162. * Also allows adjustment of diameter at print time (vs at slicing)
  1163. * Single extruder only at this point (extruder 0)
  1164. *
  1165. * Motherboards
  1166. * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
  1167. * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
  1168. * 301 - Rambo - uses Analog input 3
  1169. * Note may require analog pins to be defined for different motherboards
  1170. **********************************************************************/
  1171. // Uncomment below to enable
  1172. //#define FILAMENT_WIDTH_SENSOR
  1173. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
  1174. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  1175. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
  1176. #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
  1177. #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
  1178. #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
  1179. #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
  1180. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
  1181. //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
  1182. //#define FILAMENT_LCD_DISPLAY
  1183. #endif
  1184. #endif // CONFIGURATION_H