My Marlin configs for Fabrikator Mini and CTC i3 Pro B
您最多选择25个主题 主题必须以字母或数字开头,可以包含连字符 (-),并且长度不得超过35个字符

Configuration.h 69KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. #define CONFIGURATION_H_VERSION 020000
  40. //===========================================================================
  41. //============================= Getting Started =============================
  42. //===========================================================================
  43. /**
  44. * Here are some standard links for getting your machine calibrated:
  45. *
  46. * http://reprap.org/wiki/Calibration
  47. * http://youtu.be/wAL9d7FgInk
  48. * http://calculator.josefprusa.cz
  49. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  50. * http://www.thingiverse.com/thing:5573
  51. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  52. * http://www.thingiverse.com/thing:298812
  53. */
  54. //===========================================================================
  55. //============================= DELTA Printer ===============================
  56. //===========================================================================
  57. // For a Delta printer start with one of the configuration files in the
  58. // config/examples/delta directory and customize for your machine.
  59. //
  60. //===========================================================================
  61. //============================= SCARA Printer ===============================
  62. //===========================================================================
  63. // For a SCARA printer start with the configuration files in
  64. // config/examples/SCARA and customize for your machine.
  65. //
  66. // @section info
  67. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  68. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  69. // build by the user have been successfully uploaded into firmware.
  70. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  71. #define SHOW_BOOTSCREEN
  72. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  73. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  74. /**
  75. * *** VENDORS PLEASE READ ***
  76. *
  77. * Marlin allows you to add a custom boot image for Graphical LCDs.
  78. * With this option Marlin will first show your custom screen followed
  79. * by the standard Marlin logo with version number and web URL.
  80. *
  81. * We encourage you to take advantage of this new feature and we also
  82. * respecfully request that you retain the unmodified Marlin boot screen.
  83. */
  84. // Enable to show the bitmap in Marlin/_Bootscreen.h on startup.
  85. //#define SHOW_CUSTOM_BOOTSCREEN
  86. // Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen.
  87. //#define CUSTOM_STATUS_SCREEN_IMAGE
  88. // @section machine
  89. /**
  90. * Select the serial port on the board to use for communication with the host.
  91. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  92. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  93. *
  94. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  95. */
  96. #define SERIAL_PORT 0
  97. /**
  98. * Select a secondary serial port on the board to use for communication with the host.
  99. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  100. * Serial port -1 is the USB emulated serial port, if available.
  101. *
  102. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  103. */
  104. #define SERIAL_PORT_2 -1
  105. /**
  106. * This setting determines the communication speed of the printer.
  107. *
  108. * 250000 works in most cases, but you might try a lower speed if
  109. * you commonly experience drop-outs during host printing.
  110. * You may try up to 1000000 to speed up SD file transfer.
  111. *
  112. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  113. */
  114. #define BAUDRATE 250000
  115. // Enable the Bluetooth serial interface on AT90USB devices
  116. //#define BLUETOOTH
  117. // The following define selects which electronics board you have.
  118. // Please choose the name from boards.h that matches your setup
  119. #ifndef MOTHERBOARD
  120. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  121. #endif
  122. // Optional custom name for your RepStrap or other custom machine
  123. // Displayed in the LCD "Ready" message
  124. //#define CUSTOM_MACHINE_NAME "3D Printer"
  125. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  126. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  127. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  128. // @section extruder
  129. // This defines the number of extruders
  130. // :[1, 2, 3, 4, 5]
  131. #define EXTRUDERS 1
  132. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  133. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
  134. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  135. //#define SINGLENOZZLE
  136. /**
  137. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  138. *
  139. * This device allows one stepper driver on a control board to drive
  140. * two to eight stepper motors, one at a time, in a manner suitable
  141. * for extruders.
  142. *
  143. * This option only allows the multiplexer to switch on tool-change.
  144. * Additional options to configure custom E moves are pending.
  145. */
  146. //#define MK2_MULTIPLEXER
  147. #if ENABLED(MK2_MULTIPLEXER)
  148. // Override the default DIO selector pins here, if needed.
  149. // Some pins files may provide defaults for these pins.
  150. //#define E_MUX0_PIN 40 // Always Required
  151. //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers
  152. //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers
  153. #endif
  154. // A dual extruder that uses a single stepper motor
  155. //#define SWITCHING_EXTRUDER
  156. #if ENABLED(SWITCHING_EXTRUDER)
  157. #define SWITCHING_EXTRUDER_SERVO_NR 0
  158. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  159. #if EXTRUDERS > 3
  160. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  161. #endif
  162. #endif
  163. // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
  164. //#define SWITCHING_NOZZLE
  165. #if ENABLED(SWITCHING_NOZZLE)
  166. #define SWITCHING_NOZZLE_SERVO_NR 0
  167. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  168. //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
  169. #endif
  170. /**
  171. * Two separate X-carriages with extruders that connect to a moving part
  172. * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  173. */
  174. //#define PARKING_EXTRUDER
  175. #if ENABLED(PARKING_EXTRUDER)
  176. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  177. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  178. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
  179. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  180. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
  181. #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking
  182. #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.
  183. #endif
  184. /**
  185. * "Mixing Extruder"
  186. * - Adds a new code, M165, to set the current mix factors.
  187. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  188. * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  189. * - This implementation supports only a single extruder.
  190. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  191. */
  192. //#define MIXING_EXTRUDER
  193. #if ENABLED(MIXING_EXTRUDER)
  194. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  195. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  196. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  197. #endif
  198. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  199. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  200. // For the other hotends it is their distance from the extruder 0 hotend.
  201. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  202. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  203. // @section machine
  204. /**
  205. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  206. *
  207. * 0 = No Power Switch
  208. * 1 = ATX
  209. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  210. *
  211. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  212. */
  213. #define POWER_SUPPLY 0
  214. #if POWER_SUPPLY > 0
  215. // Enable this option to leave the PSU off at startup.
  216. // Power to steppers and heaters will need to be turned on with M80.
  217. //#define PS_DEFAULT_OFF
  218. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  219. #if ENABLED(AUTO_POWER_CONTROL)
  220. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  221. #define AUTO_POWER_E_FANS
  222. #define AUTO_POWER_CONTROLLERFAN
  223. #define POWER_TIMEOUT 30
  224. #endif
  225. #endif
  226. // @section temperature
  227. //===========================================================================
  228. //============================= Thermal Settings ============================
  229. //===========================================================================
  230. /**
  231. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  232. *
  233. * Temperature sensors available:
  234. *
  235. * -4 : thermocouple with AD8495
  236. * -3 : thermocouple with MAX31855 (only for sensor 0)
  237. * -2 : thermocouple with MAX6675 (only for sensor 0)
  238. * -1 : thermocouple with AD595
  239. * 0 : not used
  240. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  241. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  242. * 3 : Mendel-parts thermistor (4.7k pullup)
  243. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  244. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  245. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  246. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  247. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  248. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  249. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  250. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  251. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  252. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  253. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  254. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  255. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  256. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  257. * 66 : 4.7M High Temperature thermistor from Dyze Design
  258. * 70 : the 100K thermistor found in the bq Hephestos 2
  259. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  260. *
  261. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  262. * (but gives greater accuracy and more stable PID)
  263. * 51 : 100k thermistor - EPCOS (1k pullup)
  264. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  265. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  266. *
  267. * 1047 : Pt1000 with 4k7 pullup
  268. * 1010 : Pt1000 with 1k pullup (non standard)
  269. * 147 : Pt100 with 4k7 pullup
  270. * 110 : Pt100 with 1k pullup (non standard)
  271. *
  272. * Use these for Testing or Development purposes. NEVER for production machine.
  273. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  274. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  275. *
  276. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  277. */
  278. #define TEMP_SENSOR_0 1
  279. #define TEMP_SENSOR_1 0
  280. #define TEMP_SENSOR_2 0
  281. #define TEMP_SENSOR_3 0
  282. #define TEMP_SENSOR_4 0
  283. #define TEMP_SENSOR_BED 0
  284. #define TEMP_SENSOR_CHAMBER 0
  285. // Dummy thermistor constant temperature readings, for use with 998 and 999
  286. #define DUMMY_THERMISTOR_998_VALUE 25
  287. #define DUMMY_THERMISTOR_999_VALUE 100
  288. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  289. // from the two sensors differ too much the print will be aborted.
  290. //#define TEMP_SENSOR_1_AS_REDUNDANT
  291. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  292. // Extruder temperature must be close to target for this long before M109 returns success
  293. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  294. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  295. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  296. // Bed temperature must be close to target for this long before M190 returns success
  297. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  298. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  299. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  300. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  301. // to check that the wiring to the thermistor is not broken.
  302. // Otherwise this would lead to the heater being powered on all the time.
  303. #define HEATER_0_MINTEMP 5
  304. #define HEATER_1_MINTEMP 5
  305. #define HEATER_2_MINTEMP 5
  306. #define HEATER_3_MINTEMP 5
  307. #define HEATER_4_MINTEMP 5
  308. #define BED_MINTEMP 5
  309. // When temperature exceeds max temp, your heater will be switched off.
  310. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  311. // You should use MINTEMP for thermistor short/failure protection.
  312. #define HEATER_0_MAXTEMP 275
  313. #define HEATER_1_MAXTEMP 275
  314. #define HEATER_2_MAXTEMP 275
  315. #define HEATER_3_MAXTEMP 275
  316. #define HEATER_4_MAXTEMP 275
  317. #define BED_MAXTEMP 150
  318. //===========================================================================
  319. //============================= PID Settings ================================
  320. //===========================================================================
  321. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  322. // Comment the following line to disable PID and enable bang-bang.
  323. #define PIDTEMP
  324. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  325. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  326. #define PID_K1 0.95 // Smoothing factor within any PID loop
  327. #if ENABLED(PIDTEMP)
  328. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  329. //#define PID_DEBUG // Sends debug data to the serial port.
  330. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  331. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  332. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  333. // Set/get with gcode: M301 E[extruder number, 0-2]
  334. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  335. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  336. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  337. // Ultimaker
  338. #define DEFAULT_Kp 22.2
  339. #define DEFAULT_Ki 1.08
  340. #define DEFAULT_Kd 114
  341. // MakerGear
  342. //#define DEFAULT_Kp 7.0
  343. //#define DEFAULT_Ki 0.1
  344. //#define DEFAULT_Kd 12
  345. // Mendel Parts V9 on 12V
  346. //#define DEFAULT_Kp 63.0
  347. //#define DEFAULT_Ki 2.25
  348. //#define DEFAULT_Kd 440
  349. #endif // PIDTEMP
  350. //===========================================================================
  351. //============================= PID > Bed Temperature Control ===============
  352. //===========================================================================
  353. /**
  354. * PID Bed Heating
  355. *
  356. * If this option is enabled set PID constants below.
  357. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  358. *
  359. * The PID frequency will be the same as the extruder PWM.
  360. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  361. * which is fine for driving a square wave into a resistive load and does not significantly
  362. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  363. * heater. If your configuration is significantly different than this and you don't understand
  364. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  365. */
  366. //#define PIDTEMPBED
  367. //#define BED_LIMIT_SWITCHING
  368. /**
  369. * Max Bed Power
  370. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  371. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  372. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  373. */
  374. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  375. #if ENABLED(PIDTEMPBED)
  376. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  377. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  378. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  379. #define DEFAULT_bedKp 10.00
  380. #define DEFAULT_bedKi .023
  381. #define DEFAULT_bedKd 305.4
  382. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  383. //from pidautotune
  384. //#define DEFAULT_bedKp 97.1
  385. //#define DEFAULT_bedKi 1.41
  386. //#define DEFAULT_bedKd 1675.16
  387. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  388. #endif // PIDTEMPBED
  389. // @section extruder
  390. /**
  391. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  392. * Add M302 to set the minimum extrusion temperature and/or turn
  393. * cold extrusion prevention on and off.
  394. *
  395. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  396. */
  397. #define PREVENT_COLD_EXTRUSION
  398. #define EXTRUDE_MINTEMP 170
  399. /**
  400. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  401. * Note: For Bowden Extruders make this large enough to allow load/unload.
  402. */
  403. #define PREVENT_LENGTHY_EXTRUDE
  404. #define EXTRUDE_MAXLENGTH 200
  405. //===========================================================================
  406. //======================== Thermal Runaway Protection =======================
  407. //===========================================================================
  408. /**
  409. * Thermal Protection provides additional protection to your printer from damage
  410. * and fire. Marlin always includes safe min and max temperature ranges which
  411. * protect against a broken or disconnected thermistor wire.
  412. *
  413. * The issue: If a thermistor falls out, it will report the much lower
  414. * temperature of the air in the room, and the the firmware will keep
  415. * the heater on.
  416. *
  417. * If you get "Thermal Runaway" or "Heating failed" errors the
  418. * details can be tuned in Configuration_adv.h
  419. */
  420. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  421. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  422. //===========================================================================
  423. //============================= Mechanical Settings =========================
  424. //===========================================================================
  425. // @section machine
  426. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  427. // either in the usual order or reversed
  428. //#define COREXY
  429. //#define COREXZ
  430. //#define COREYZ
  431. //#define COREYX
  432. //#define COREZX
  433. //#define COREZY
  434. //===========================================================================
  435. //============================== Endstop Settings ===========================
  436. //===========================================================================
  437. // @section homing
  438. // Specify here all the endstop connectors that are connected to any endstop or probe.
  439. // Almost all printers will be using one per axis. Probes will use one or more of the
  440. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  441. #define USE_XMIN_PLUG
  442. #define USE_YMIN_PLUG
  443. #define USE_ZMIN_PLUG
  444. //#define USE_XMAX_PLUG
  445. //#define USE_YMAX_PLUG
  446. //#define USE_ZMAX_PLUG
  447. // Enable pullup for all endstops to prevent a floating state
  448. #define ENDSTOPPULLUPS
  449. #if DISABLED(ENDSTOPPULLUPS)
  450. // Disable ENDSTOPPULLUPS to set pullups individually
  451. //#define ENDSTOPPULLUP_XMAX
  452. //#define ENDSTOPPULLUP_YMAX
  453. //#define ENDSTOPPULLUP_ZMAX
  454. //#define ENDSTOPPULLUP_XMIN
  455. //#define ENDSTOPPULLUP_YMIN
  456. //#define ENDSTOPPULLUP_ZMIN
  457. //#define ENDSTOPPULLUP_ZMIN_PROBE
  458. #endif
  459. // Enable pulldown for all endstops to prevent a floating state
  460. //#define ENDSTOPPULLDOWNS
  461. #if DISABLED(ENDSTOPPULLDOWNS)
  462. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  463. //#define ENDSTOPPULLDOWN_XMAX
  464. //#define ENDSTOPPULLDOWN_YMAX
  465. //#define ENDSTOPPULLDOWN_ZMAX
  466. //#define ENDSTOPPULLDOWN_XMIN
  467. //#define ENDSTOPPULLDOWN_YMIN
  468. //#define ENDSTOPPULLDOWN_ZMIN
  469. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  470. #endif
  471. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  472. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  473. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  474. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  475. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  476. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  477. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  478. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
  479. // Enable this feature if all enabled endstop pins are interrupt-capable.
  480. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  481. //#define ENDSTOP_INTERRUPTS_FEATURE
  482. //=============================================================================
  483. //============================== Movement Settings ============================
  484. //=============================================================================
  485. // @section motion
  486. /**
  487. * Default Settings
  488. *
  489. * These settings can be reset by M502
  490. *
  491. * Note that if EEPROM is enabled, saved values will override these.
  492. */
  493. /**
  494. * With this option each E stepper can have its own factors for the
  495. * following movement settings. If fewer factors are given than the
  496. * total number of extruders, the last value applies to the rest.
  497. */
  498. //#define DISTINCT_E_FACTORS
  499. /**
  500. * Default Axis Steps Per Unit (steps/mm)
  501. * Override with M92
  502. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  503. */
  504. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  505. /**
  506. * Default Max Feed Rate (mm/s)
  507. * Override with M203
  508. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  509. */
  510. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  511. /**
  512. * Default Max Acceleration (change/s) change = mm/s
  513. * (Maximum start speed for accelerated moves)
  514. * Override with M201
  515. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  516. */
  517. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  518. /**
  519. * Default Acceleration (change/s) change = mm/s
  520. * Override with M204
  521. *
  522. * M204 P Acceleration
  523. * M204 R Retract Acceleration
  524. * M204 T Travel Acceleration
  525. */
  526. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  527. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  528. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  529. /**
  530. * Default Jerk (mm/s)
  531. * Override with M205 X Y Z E
  532. *
  533. * "Jerk" specifies the minimum speed change that requires acceleration.
  534. * When changing speed and direction, if the difference is less than the
  535. * value set here, it may happen instantaneously.
  536. */
  537. #define DEFAULT_XJERK 10.0
  538. #define DEFAULT_YJERK 10.0
  539. #define DEFAULT_ZJERK 0.3
  540. #define DEFAULT_EJERK 5.0
  541. /**
  542. * Realtime Jerk Control
  543. *
  544. * This option eliminates vibration during printing by fitting a Bézier
  545. * curve to move acceleration, producing much smoother direction changes.
  546. * Because this is computationally-intensive, a 32-bit MCU is required.
  547. *
  548. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  549. */
  550. //#define BEZIER_JERK_CONTROL
  551. //===========================================================================
  552. //============================= Z Probe Options =============================
  553. //===========================================================================
  554. // @section probes
  555. //
  556. // See http://marlinfw.org/docs/configuration/probes.html
  557. //
  558. /**
  559. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  560. *
  561. * Enable this option for a probe connected to the Z Min endstop pin.
  562. */
  563. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  564. /**
  565. * Z_MIN_PROBE_ENDSTOP
  566. *
  567. * Enable this option for a probe connected to any pin except Z-Min.
  568. * (By default Marlin assumes the Z-Max endstop pin.)
  569. * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  570. *
  571. * - The simplest option is to use a free endstop connector.
  572. * - Use 5V for powered (usually inductive) sensors.
  573. *
  574. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  575. * - For simple switches connect...
  576. * - normally-closed switches to GND and D32.
  577. * - normally-open switches to 5V and D32.
  578. *
  579. * WARNING: Setting the wrong pin may have unexpected and potentially
  580. * disastrous consequences. Use with caution and do your homework.
  581. *
  582. */
  583. //#define Z_MIN_PROBE_ENDSTOP
  584. /**
  585. * Probe Type
  586. *
  587. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  588. * Activate one of these to use Auto Bed Leveling below.
  589. */
  590. /**
  591. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  592. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  593. * or (with LCD_BED_LEVELING) the LCD controller.
  594. */
  595. //#define PROBE_MANUALLY
  596. /**
  597. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  598. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  599. */
  600. //#define FIX_MOUNTED_PROBE
  601. /**
  602. * Z Servo Probe, such as an endstop switch on a rotating arm.
  603. */
  604. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  605. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  606. /**
  607. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  608. */
  609. //#define BLTOUCH
  610. #if ENABLED(BLTOUCH)
  611. //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
  612. #endif
  613. /**
  614. * Enable one or more of the following if probing seems unreliable.
  615. * Heaters and/or fans can be disabled during probing to minimize electrical
  616. * noise. A delay can also be added to allow noise and vibration to settle.
  617. * These options are most useful for the BLTouch probe, but may also improve
  618. * readings with inductive probes and piezo sensors.
  619. */
  620. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  621. #if ENABLED(PROBING_HEATERS_OFF)
  622. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  623. #endif
  624. //#define PROBING_FANS_OFF // Turn fans off when probing
  625. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  626. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  627. //#define SOLENOID_PROBE
  628. // A sled-mounted probe like those designed by Charles Bell.
  629. //#define Z_PROBE_SLED
  630. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  631. //
  632. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  633. //
  634. /**
  635. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  636. * X and Y offsets must be integers.
  637. *
  638. * In the following example the X and Y offsets are both positive:
  639. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  640. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  641. *
  642. * +-- BACK ---+
  643. * | |
  644. * L | (+) P | R <-- probe (20,20)
  645. * E | | I
  646. * F | (-) N (+) | G <-- nozzle (10,10)
  647. * T | | H
  648. * | (-) | T
  649. * | |
  650. * O-- FRONT --+
  651. * (0,0)
  652. */
  653. #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
  654. #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
  655. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
  656. // Certain types of probes need to stay away from edges
  657. #define MIN_PROBE_EDGE 10
  658. // X and Y axis travel speed (mm/m) between probes
  659. #define XY_PROBE_SPEED 8000
  660. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  661. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  662. // Feedrate (mm/m) for the "accurate" probe of each point
  663. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  664. // The number of probes to perform at each point.
  665. // Set to 2 for a fast/slow probe, using the second probe result.
  666. // Set to 3 or more for slow probes, averaging the results.
  667. //#define MULTIPLE_PROBING 2
  668. /**
  669. * Z probes require clearance when deploying, stowing, and moving between
  670. * probe points to avoid hitting the bed and other hardware.
  671. * Servo-mounted probes require extra space for the arm to rotate.
  672. * Inductive probes need space to keep from triggering early.
  673. *
  674. * Use these settings to specify the distance (mm) to raise the probe (or
  675. * lower the bed). The values set here apply over and above any (negative)
  676. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  677. * Only integer values >= 1 are valid here.
  678. *
  679. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  680. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  681. */
  682. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  683. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  684. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  685. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  686. // For M851 give a range for adjusting the Z probe offset
  687. #define Z_PROBE_OFFSET_RANGE_MIN -20
  688. #define Z_PROBE_OFFSET_RANGE_MAX 20
  689. // Enable the M48 repeatability test to test probe accuracy
  690. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  691. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  692. // :{ 0:'Low', 1:'High' }
  693. #define X_ENABLE_ON 0
  694. #define Y_ENABLE_ON 0
  695. #define Z_ENABLE_ON 0
  696. #define E_ENABLE_ON 0 // For all extruders
  697. // Disables axis stepper immediately when it's not being used.
  698. // WARNING: When motors turn off there is a chance of losing position accuracy!
  699. #define DISABLE_X false
  700. #define DISABLE_Y false
  701. #define DISABLE_Z false
  702. // Warn on display about possibly reduced accuracy
  703. //#define DISABLE_REDUCED_ACCURACY_WARNING
  704. // @section extruder
  705. #define DISABLE_E false // For all extruders
  706. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  707. // @section machine
  708. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  709. #define INVERT_X_DIR false
  710. #define INVERT_Y_DIR true
  711. #define INVERT_Z_DIR false
  712. // Enable this option for Toshiba stepper drivers
  713. //#define CONFIG_STEPPERS_TOSHIBA
  714. // @section extruder
  715. // For direct drive extruder v9 set to true, for geared extruder set to false.
  716. #define INVERT_E0_DIR false
  717. #define INVERT_E1_DIR false
  718. #define INVERT_E2_DIR false
  719. #define INVERT_E3_DIR false
  720. #define INVERT_E4_DIR false
  721. // @section homing
  722. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  723. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  724. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  725. // Be sure you have this distance over your Z_MAX_POS in case.
  726. // Direction of endstops when homing; 1=MAX, -1=MIN
  727. // :[-1,1]
  728. #define X_HOME_DIR -1
  729. #define Y_HOME_DIR -1
  730. #define Z_HOME_DIR -1
  731. // @section machine
  732. // The size of the print bed
  733. #define X_BED_SIZE 200
  734. #define Y_BED_SIZE 200
  735. // Travel limits (mm) after homing, corresponding to endstop positions.
  736. #define X_MIN_POS 0
  737. #define Y_MIN_POS 0
  738. #define Z_MIN_POS 0
  739. #define X_MAX_POS X_BED_SIZE
  740. #define Y_MAX_POS Y_BED_SIZE
  741. #define Z_MAX_POS 200
  742. /**
  743. * Software Endstops
  744. *
  745. * - Prevent moves outside the set machine bounds.
  746. * - Individual axes can be disabled, if desired.
  747. * - X and Y only apply to Cartesian robots.
  748. * - Use 'M211' to set software endstops on/off or report current state
  749. */
  750. // Min software endstops constrain movement within minimum coordinate bounds
  751. #define MIN_SOFTWARE_ENDSTOPS
  752. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  753. #define MIN_SOFTWARE_ENDSTOP_X
  754. #define MIN_SOFTWARE_ENDSTOP_Y
  755. #define MIN_SOFTWARE_ENDSTOP_Z
  756. #endif
  757. // Max software endstops constrain movement within maximum coordinate bounds
  758. #define MAX_SOFTWARE_ENDSTOPS
  759. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  760. #define MAX_SOFTWARE_ENDSTOP_X
  761. #define MAX_SOFTWARE_ENDSTOP_Y
  762. #define MAX_SOFTWARE_ENDSTOP_Z
  763. #endif
  764. #if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
  765. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  766. #endif
  767. /**
  768. * Filament Runout Sensors
  769. * Mechanical or opto endstops are used to check for the presence of filament.
  770. *
  771. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  772. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  773. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  774. */
  775. //#define FILAMENT_RUNOUT_SENSOR
  776. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  777. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  778. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  779. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  780. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  781. #define FILAMENT_RUNOUT_SCRIPT "M600"
  782. #endif
  783. //===========================================================================
  784. //=============================== Bed Leveling ==============================
  785. //===========================================================================
  786. // @section calibrate
  787. /**
  788. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  789. * and behavior of G29 will change depending on your selection.
  790. *
  791. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  792. *
  793. * - AUTO_BED_LEVELING_3POINT
  794. * Probe 3 arbitrary points on the bed (that aren't collinear)
  795. * You specify the XY coordinates of all 3 points.
  796. * The result is a single tilted plane. Best for a flat bed.
  797. *
  798. * - AUTO_BED_LEVELING_LINEAR
  799. * Probe several points in a grid.
  800. * You specify the rectangle and the density of sample points.
  801. * The result is a single tilted plane. Best for a flat bed.
  802. *
  803. * - AUTO_BED_LEVELING_BILINEAR
  804. * Probe several points in a grid.
  805. * You specify the rectangle and the density of sample points.
  806. * The result is a mesh, best for large or uneven beds.
  807. *
  808. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  809. * A comprehensive bed leveling system combining the features and benefits
  810. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  811. * Validation and Mesh Editing systems.
  812. *
  813. * - MESH_BED_LEVELING
  814. * Probe a grid manually
  815. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  816. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  817. * leveling in steps so you can manually adjust the Z height at each grid-point.
  818. * With an LCD controller the process is guided step-by-step.
  819. */
  820. //#define AUTO_BED_LEVELING_3POINT
  821. //#define AUTO_BED_LEVELING_LINEAR
  822. //#define AUTO_BED_LEVELING_BILINEAR
  823. //#define AUTO_BED_LEVELING_UBL
  824. //#define MESH_BED_LEVELING
  825. /**
  826. * Normally G28 leaves leveling disabled on completion. Enable
  827. * this option to have G28 restore the prior leveling state.
  828. */
  829. //#define RESTORE_LEVELING_AFTER_G28
  830. /**
  831. * Enable detailed logging of G28, G29, M48, etc.
  832. * Turn on with the command 'M111 S32'.
  833. * NOTE: Requires a lot of PROGMEM!
  834. */
  835. //#define DEBUG_LEVELING_FEATURE
  836. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  837. // Gradually reduce leveling correction until a set height is reached,
  838. // at which point movement will be level to the machine's XY plane.
  839. // The height can be set with M420 Z<height>
  840. #define ENABLE_LEVELING_FADE_HEIGHT
  841. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  842. // split up moves into short segments like a Delta. This follows the
  843. // contours of the bed more closely than edge-to-edge straight moves.
  844. #define SEGMENT_LEVELED_MOVES
  845. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  846. /**
  847. * Enable the G26 Mesh Validation Pattern tool.
  848. */
  849. //#define G26_MESH_VALIDATION
  850. #if ENABLED(G26_MESH_VALIDATION)
  851. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  852. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  853. #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  854. #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  855. #endif
  856. #endif
  857. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  858. // Set the number of grid points per dimension.
  859. #define GRID_MAX_POINTS_X 3
  860. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  861. // Set the boundaries for probing (where the probe can reach).
  862. //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
  863. //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE)
  864. //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
  865. //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE)
  866. // Probe along the Y axis, advancing X after each column
  867. //#define PROBE_Y_FIRST
  868. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  869. // Beyond the probed grid, continue the implied tilt?
  870. // Default is to maintain the height of the nearest edge.
  871. //#define EXTRAPOLATE_BEYOND_GRID
  872. //
  873. // Experimental Subdivision of the grid by Catmull-Rom method.
  874. // Synthesizes intermediate points to produce a more detailed mesh.
  875. //
  876. //#define ABL_BILINEAR_SUBDIVISION
  877. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  878. // Number of subdivisions between probe points
  879. #define BILINEAR_SUBDIVISIONS 3
  880. #endif
  881. #endif
  882. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  883. //===========================================================================
  884. //========================= Unified Bed Leveling ============================
  885. //===========================================================================
  886. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  887. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  888. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  889. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  890. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  891. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  892. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  893. // as the Z-Height correction value.
  894. #elif ENABLED(MESH_BED_LEVELING)
  895. //===========================================================================
  896. //=================================== Mesh ==================================
  897. //===========================================================================
  898. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  899. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  900. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  901. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  902. #endif // BED_LEVELING
  903. /**
  904. * Points to probe for all 3-point Leveling procedures.
  905. * Override if the automatically selected points are inadequate.
  906. */
  907. #if ENABLED(AUTO_BED_LEVELING_3POINT) || ENABLED(AUTO_BED_LEVELING_UBL)
  908. //#define PROBE_PT_1_X 15
  909. //#define PROBE_PT_1_Y 180
  910. //#define PROBE_PT_2_X 15
  911. //#define PROBE_PT_2_Y 20
  912. //#define PROBE_PT_3_X 170
  913. //#define PROBE_PT_3_Y 20
  914. #endif
  915. /**
  916. * Add a bed leveling sub-menu for ABL or MBL.
  917. * Include a guided procedure if manual probing is enabled.
  918. */
  919. //#define LCD_BED_LEVELING
  920. #if ENABLED(LCD_BED_LEVELING)
  921. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  922. #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  923. #endif
  924. // Add a menu item to move between bed corners for manual bed adjustment
  925. //#define LEVEL_BED_CORNERS
  926. #if ENABLED(LEVEL_BED_CORNERS)
  927. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  928. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  929. #endif
  930. /**
  931. * Commands to execute at the end of G29 probing.
  932. * Useful to retract or move the Z probe out of the way.
  933. */
  934. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  935. // @section homing
  936. // The center of the bed is at (X=0, Y=0)
  937. //#define BED_CENTER_AT_0_0
  938. // Manually set the home position. Leave these undefined for automatic settings.
  939. // For DELTA this is the top-center of the Cartesian print volume.
  940. //#define MANUAL_X_HOME_POS 0
  941. //#define MANUAL_Y_HOME_POS 0
  942. //#define MANUAL_Z_HOME_POS 0
  943. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  944. //
  945. // With this feature enabled:
  946. //
  947. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  948. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  949. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  950. // - Prevent Z homing when the Z probe is outside bed area.
  951. //
  952. //#define Z_SAFE_HOMING
  953. #if ENABLED(Z_SAFE_HOMING)
  954. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  955. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  956. #endif
  957. // Homing speeds (mm/m)
  958. #define HOMING_FEEDRATE_XY (50*60)
  959. #define HOMING_FEEDRATE_Z (4*60)
  960. // @section calibrate
  961. /**
  962. * Bed Skew Compensation
  963. *
  964. * This feature corrects for misalignment in the XYZ axes.
  965. *
  966. * Take the following steps to get the bed skew in the XY plane:
  967. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  968. * 2. For XY_DIAG_AC measure the diagonal A to C
  969. * 3. For XY_DIAG_BD measure the diagonal B to D
  970. * 4. For XY_SIDE_AD measure the edge A to D
  971. *
  972. * Marlin automatically computes skew factors from these measurements.
  973. * Skew factors may also be computed and set manually:
  974. *
  975. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  976. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  977. *
  978. * If desired, follow the same procedure for XZ and YZ.
  979. * Use these diagrams for reference:
  980. *
  981. * Y Z Z
  982. * ^ B-------C ^ B-------C ^ B-------C
  983. * | / / | / / | / /
  984. * | / / | / / | / /
  985. * | A-------D | A-------D | A-------D
  986. * +-------------->X +-------------->X +-------------->Y
  987. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  988. */
  989. //#define SKEW_CORRECTION
  990. #if ENABLED(SKEW_CORRECTION)
  991. // Input all length measurements here:
  992. #define XY_DIAG_AC 282.8427124746
  993. #define XY_DIAG_BD 282.8427124746
  994. #define XY_SIDE_AD 200
  995. // Or, set the default skew factors directly here
  996. // to override the above measurements:
  997. #define XY_SKEW_FACTOR 0.0
  998. //#define SKEW_CORRECTION_FOR_Z
  999. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1000. #define XZ_DIAG_AC 282.8427124746
  1001. #define XZ_DIAG_BD 282.8427124746
  1002. #define YZ_DIAG_AC 282.8427124746
  1003. #define YZ_DIAG_BD 282.8427124746
  1004. #define YZ_SIDE_AD 200
  1005. #define XZ_SKEW_FACTOR 0.0
  1006. #define YZ_SKEW_FACTOR 0.0
  1007. #endif
  1008. // Enable this option for M852 to set skew at runtime
  1009. //#define SKEW_CORRECTION_GCODE
  1010. #endif
  1011. //=============================================================================
  1012. //============================= Additional Features ===========================
  1013. //=============================================================================
  1014. // @section extras
  1015. //
  1016. // EEPROM
  1017. //
  1018. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  1019. // M500 - stores parameters in EEPROM
  1020. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  1021. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  1022. //
  1023. //#define EEPROM_SETTINGS // Enable for M500 and M501 commands
  1024. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1025. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1026. //
  1027. // Host Keepalive
  1028. //
  1029. // When enabled Marlin will send a busy status message to the host
  1030. // every couple of seconds when it can't accept commands.
  1031. //
  1032. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1033. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1034. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1035. //
  1036. // M100 Free Memory Watcher
  1037. //
  1038. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1039. //
  1040. // G20/G21 Inch mode support
  1041. //
  1042. //#define INCH_MODE_SUPPORT
  1043. //
  1044. // M149 Set temperature units support
  1045. //
  1046. //#define TEMPERATURE_UNITS_SUPPORT
  1047. // @section temperature
  1048. // Preheat Constants
  1049. #define PREHEAT_1_TEMP_HOTEND 180
  1050. #define PREHEAT_1_TEMP_BED 70
  1051. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1052. #define PREHEAT_2_TEMP_HOTEND 240
  1053. #define PREHEAT_2_TEMP_BED 110
  1054. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1055. /**
  1056. * Nozzle Park
  1057. *
  1058. * Park the nozzle at the given XYZ position on idle or G27.
  1059. *
  1060. * The "P" parameter controls the action applied to the Z axis:
  1061. *
  1062. * P0 (Default) If Z is below park Z raise the nozzle.
  1063. * P1 Raise the nozzle always to Z-park height.
  1064. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1065. */
  1066. //#define NOZZLE_PARK_FEATURE
  1067. #if ENABLED(NOZZLE_PARK_FEATURE)
  1068. // Specify a park position as { X, Y, Z }
  1069. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1070. #define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  1071. #define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
  1072. #endif
  1073. /**
  1074. * Clean Nozzle Feature -- EXPERIMENTAL
  1075. *
  1076. * Adds the G12 command to perform a nozzle cleaning process.
  1077. *
  1078. * Parameters:
  1079. * P Pattern
  1080. * S Strokes / Repetitions
  1081. * T Triangles (P1 only)
  1082. *
  1083. * Patterns:
  1084. * P0 Straight line (default). This process requires a sponge type material
  1085. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1086. * between the start / end points.
  1087. *
  1088. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1089. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1090. * Zig-zags are done in whichever is the narrower dimension.
  1091. * For example, "G12 P1 S1 T3" will execute:
  1092. *
  1093. * --
  1094. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1095. * | | / \ / \ / \ |
  1096. * A | | / \ / \ / \ |
  1097. * | | / \ / \ / \ |
  1098. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1099. * -- +--------------------------------+
  1100. * |________|_________|_________|
  1101. * T1 T2 T3
  1102. *
  1103. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1104. * "R" specifies the radius. "S" specifies the stroke count.
  1105. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1106. *
  1107. * Caveats: The ending Z should be the same as starting Z.
  1108. * Attention: EXPERIMENTAL. G-code arguments may change.
  1109. *
  1110. */
  1111. //#define NOZZLE_CLEAN_FEATURE
  1112. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1113. // Default number of pattern repetitions
  1114. #define NOZZLE_CLEAN_STROKES 12
  1115. // Default number of triangles
  1116. #define NOZZLE_CLEAN_TRIANGLES 3
  1117. // Specify positions as { X, Y, Z }
  1118. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  1119. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  1120. // Circular pattern radius
  1121. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1122. // Circular pattern circle fragments number
  1123. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1124. // Middle point of circle
  1125. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1126. // Moves the nozzle to the initial position
  1127. #define NOZZLE_CLEAN_GOBACK
  1128. #endif
  1129. /**
  1130. * Print Job Timer
  1131. *
  1132. * Automatically start and stop the print job timer on M104/M109/M190.
  1133. *
  1134. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1135. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1136. * M190 (bed, wait) - high temp = start timer, low temp = none
  1137. *
  1138. * The timer can also be controlled with the following commands:
  1139. *
  1140. * M75 - Start the print job timer
  1141. * M76 - Pause the print job timer
  1142. * M77 - Stop the print job timer
  1143. */
  1144. #define PRINTJOB_TIMER_AUTOSTART
  1145. /**
  1146. * Print Counter
  1147. *
  1148. * Track statistical data such as:
  1149. *
  1150. * - Total print jobs
  1151. * - Total successful print jobs
  1152. * - Total failed print jobs
  1153. * - Total time printing
  1154. *
  1155. * View the current statistics with M78.
  1156. */
  1157. //#define PRINTCOUNTER
  1158. //=============================================================================
  1159. //============================= LCD and SD support ============================
  1160. //=============================================================================
  1161. // @section lcd
  1162. /**
  1163. * LCD LANGUAGE
  1164. *
  1165. * Select the language to display on the LCD. These languages are available:
  1166. *
  1167. * en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr,
  1168. * gl, hr, it, jp-kana, nl, pl, pt, pt-br, ru, sk,
  1169. * tr, uk, zh_CN, zh_TW, test
  1170. *
  1171. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', test':'TEST' }
  1172. */
  1173. #define LCD_LANGUAGE en
  1174. /**
  1175. * LCD Character Set
  1176. *
  1177. * Note: This option is NOT applicable to Graphical Displays.
  1178. *
  1179. * All character-based LCDs provide ASCII plus one of these
  1180. * language extensions:
  1181. *
  1182. * - JAPANESE ... the most common
  1183. * - WESTERN ... with more accented characters
  1184. * - CYRILLIC ... for the Russian language
  1185. *
  1186. * To determine the language extension installed on your controller:
  1187. *
  1188. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1189. * - Click the controller to view the LCD menu
  1190. * - The LCD will display Japanese, Western, or Cyrillic text
  1191. *
  1192. * See http://marlinfw.org/docs/development/lcd_language.html
  1193. *
  1194. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1195. */
  1196. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1197. /**
  1198. * SD CARD
  1199. *
  1200. * SD Card support is disabled by default. If your controller has an SD slot,
  1201. * you must uncomment the following option or it won't work.
  1202. *
  1203. */
  1204. //#define SDSUPPORT
  1205. /**
  1206. * SD CARD: SPI SPEED
  1207. *
  1208. * Enable one of the following items for a slower SPI transfer speed.
  1209. * This may be required to resolve "volume init" errors.
  1210. */
  1211. //#define SPI_SPEED SPI_HALF_SPEED
  1212. //#define SPI_SPEED SPI_QUARTER_SPEED
  1213. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1214. /**
  1215. * SD CARD: ENABLE CRC
  1216. *
  1217. * Use CRC checks and retries on the SD communication.
  1218. */
  1219. //#define SD_CHECK_AND_RETRY
  1220. /**
  1221. * LCD Menu Items
  1222. *
  1223. * Disable all menus and only display the Status Screen, or
  1224. * just remove some extraneous menu items to recover space.
  1225. */
  1226. //#define NO_LCD_MENUS
  1227. //#define SLIM_LCD_MENUS
  1228. //
  1229. // ENCODER SETTINGS
  1230. //
  1231. // This option overrides the default number of encoder pulses needed to
  1232. // produce one step. Should be increased for high-resolution encoders.
  1233. //
  1234. //#define ENCODER_PULSES_PER_STEP 4
  1235. //
  1236. // Use this option to override the number of step signals required to
  1237. // move between next/prev menu items.
  1238. //
  1239. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1240. /**
  1241. * Encoder Direction Options
  1242. *
  1243. * Test your encoder's behavior first with both options disabled.
  1244. *
  1245. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1246. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1247. * Reversed Value Editing only? Enable BOTH options.
  1248. */
  1249. //
  1250. // This option reverses the encoder direction everywhere.
  1251. //
  1252. // Set this option if CLOCKWISE causes values to DECREASE
  1253. //
  1254. //#define REVERSE_ENCODER_DIRECTION
  1255. //
  1256. // This option reverses the encoder direction for navigating LCD menus.
  1257. //
  1258. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1259. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1260. //
  1261. //#define REVERSE_MENU_DIRECTION
  1262. //
  1263. // Individual Axis Homing
  1264. //
  1265. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1266. //
  1267. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1268. //
  1269. // SPEAKER/BUZZER
  1270. //
  1271. // If you have a speaker that can produce tones, enable it here.
  1272. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1273. //
  1274. //#define SPEAKER
  1275. //
  1276. // The duration and frequency for the UI feedback sound.
  1277. // Set these to 0 to disable audio feedback in the LCD menus.
  1278. //
  1279. // Note: Test audio output with the G-Code:
  1280. // M300 S<frequency Hz> P<duration ms>
  1281. //
  1282. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1283. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1284. //=============================================================================
  1285. //======================== LCD / Controller Selection =========================
  1286. //======================== (Character-based LCDs) =========================
  1287. //=============================================================================
  1288. //
  1289. // RepRapDiscount Smart Controller.
  1290. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1291. //
  1292. // Note: Usually sold with a white PCB.
  1293. //
  1294. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1295. //
  1296. // Original RADDS LCD Display+Encoder+SDCardReader
  1297. // http://doku.radds.org/dokumentation/lcd-display/
  1298. //
  1299. //#define RADDS_DISPLAY
  1300. //
  1301. // ULTIMAKER Controller.
  1302. //
  1303. //#define ULTIMAKERCONTROLLER
  1304. //
  1305. // ULTIPANEL as seen on Thingiverse.
  1306. //
  1307. //#define ULTIPANEL
  1308. //
  1309. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1310. // http://reprap.org/wiki/PanelOne
  1311. //
  1312. //#define PANEL_ONE
  1313. //
  1314. // GADGETS3D G3D LCD/SD Controller
  1315. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1316. //
  1317. // Note: Usually sold with a blue PCB.
  1318. //
  1319. //#define G3D_PANEL
  1320. //
  1321. // RigidBot Panel V1.0
  1322. // http://www.inventapart.com/
  1323. //
  1324. //#define RIGIDBOT_PANEL
  1325. //
  1326. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1327. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1328. //
  1329. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1330. //
  1331. // ANET and Tronxy 20x4 Controller
  1332. //
  1333. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1334. // This LCD is known to be susceptible to electrical interference
  1335. // which scrambles the display. Pressing any button clears it up.
  1336. // This is a LCD2004 display with 5 analog buttons.
  1337. //
  1338. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1339. //
  1340. //#define ULTRA_LCD
  1341. //=============================================================================
  1342. //======================== LCD / Controller Selection =========================
  1343. //===================== (I2C and Shift-Register LCDs) =====================
  1344. //=============================================================================
  1345. //
  1346. // CONTROLLER TYPE: I2C
  1347. //
  1348. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1349. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1350. //
  1351. //
  1352. // Elefu RA Board Control Panel
  1353. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1354. //
  1355. //#define RA_CONTROL_PANEL
  1356. //
  1357. // Sainsmart (YwRobot) LCD Displays
  1358. //
  1359. // These require F.Malpartida's LiquidCrystal_I2C library
  1360. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1361. //
  1362. //#define LCD_SAINSMART_I2C_1602
  1363. //#define LCD_SAINSMART_I2C_2004
  1364. //
  1365. // Generic LCM1602 LCD adapter
  1366. //
  1367. //#define LCM1602
  1368. //
  1369. // PANELOLU2 LCD with status LEDs,
  1370. // separate encoder and click inputs.
  1371. //
  1372. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1373. // For more info: https://github.com/lincomatic/LiquidTWI2
  1374. //
  1375. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1376. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1377. //
  1378. //#define LCD_I2C_PANELOLU2
  1379. //
  1380. // Panucatt VIKI LCD with status LEDs,
  1381. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1382. //
  1383. //#define LCD_I2C_VIKI
  1384. //
  1385. // CONTROLLER TYPE: Shift register panels
  1386. //
  1387. //
  1388. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1389. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1390. //
  1391. //#define SAV_3DLCD
  1392. //=============================================================================
  1393. //======================= LCD / Controller Selection =======================
  1394. //========================= (Graphical LCDs) ========================
  1395. //=============================================================================
  1396. //
  1397. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1398. //
  1399. // IMPORTANT: The U8glib library is required for Graphical Display!
  1400. // https://github.com/olikraus/U8glib_Arduino
  1401. //
  1402. //
  1403. // RepRapDiscount FULL GRAPHIC Smart Controller
  1404. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1405. //
  1406. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1407. //
  1408. // ReprapWorld Graphical LCD
  1409. // https://reprapworld.com/?products_details&products_id/1218
  1410. //
  1411. //#define REPRAPWORLD_GRAPHICAL_LCD
  1412. //
  1413. // Activate one of these if you have a Panucatt Devices
  1414. // Viki 2.0 or mini Viki with Graphic LCD
  1415. // http://panucatt.com
  1416. //
  1417. //#define VIKI2
  1418. //#define miniVIKI
  1419. //
  1420. // MakerLab Mini Panel with graphic
  1421. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1422. //
  1423. //#define MINIPANEL
  1424. //
  1425. // MaKr3d Makr-Panel with graphic controller and SD support.
  1426. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1427. //
  1428. //#define MAKRPANEL
  1429. //
  1430. // Adafruit ST7565 Full Graphic Controller.
  1431. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1432. //
  1433. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1434. //
  1435. // BQ LCD Smart Controller shipped by
  1436. // default with the BQ Hephestos 2 and Witbox 2.
  1437. //
  1438. //#define BQ_LCD_SMART_CONTROLLER
  1439. //
  1440. // Cartesio UI
  1441. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1442. //
  1443. //#define CARTESIO_UI
  1444. //
  1445. // LCD for Melzi Card with Graphical LCD
  1446. //
  1447. //#define LCD_FOR_MELZI
  1448. //
  1449. // SSD1306 OLED full graphics generic display
  1450. //
  1451. //#define U8GLIB_SSD1306
  1452. //
  1453. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1454. //
  1455. //#define SAV_3DGLCD
  1456. #if ENABLED(SAV_3DGLCD)
  1457. //#define U8GLIB_SSD1306
  1458. #define U8GLIB_SH1106
  1459. #endif
  1460. //
  1461. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1462. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1463. //
  1464. //#define ULTI_CONTROLLER
  1465. //
  1466. // TinyBoy2 128x64 OLED / Encoder Panel
  1467. //
  1468. //#define OLED_PANEL_TINYBOY2
  1469. //
  1470. // MKS MINI12864 with graphic controller and SD support
  1471. // http://reprap.org/wiki/MKS_MINI_12864
  1472. //
  1473. //#define MKS_MINI_12864
  1474. //
  1475. // Factory display for Creality CR-10
  1476. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1477. //
  1478. // This is RAMPS-compatible using a single 10-pin connector.
  1479. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1480. //
  1481. //#define CR10_STOCKDISPLAY
  1482. //
  1483. // ANET and Tronxy Graphical Controller
  1484. //
  1485. //#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1486. // A clone of the RepRapDiscount full graphics display but with
  1487. // different pins/wiring (see pins_ANET_10.h).
  1488. //
  1489. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1490. // http://reprap.org/wiki/MKS_12864OLED
  1491. //
  1492. // Tiny, but very sharp OLED display
  1493. //
  1494. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1495. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1496. //
  1497. // AZSMZ 12864 LCD with SD
  1498. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1499. //
  1500. //#define AZSMZ_12864
  1501. //
  1502. // Silvergate GLCD controller
  1503. // http://github.com/android444/Silvergate
  1504. //
  1505. //#define SILVER_GATE_GLCD_CONTROLLER
  1506. //=============================================================================
  1507. //============================ Other Controllers ============================
  1508. //=============================================================================
  1509. //
  1510. // CONTROLLER TYPE: Standalone / Serial
  1511. //
  1512. //
  1513. // LCD for Malyan M200 printers.
  1514. // This requires SDSUPPORT to be enabled
  1515. //
  1516. //#define MALYAN_LCD
  1517. //
  1518. // CONTROLLER TYPE: Keypad / Add-on
  1519. //
  1520. //
  1521. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1522. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1523. //
  1524. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1525. // is pressed, a value of 10.0 means 10mm per click.
  1526. //
  1527. //#define REPRAPWORLD_KEYPAD
  1528. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
  1529. //=============================================================================
  1530. //=============================== Extra Features ==============================
  1531. //=============================================================================
  1532. // @section extras
  1533. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1534. //#define FAST_PWM_FAN
  1535. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1536. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1537. // is too low, you should also increment SOFT_PWM_SCALE.
  1538. //#define FAN_SOFT_PWM
  1539. // Incrementing this by 1 will double the software PWM frequency,
  1540. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1541. // However, control resolution will be halved for each increment;
  1542. // at zero value, there are 128 effective control positions.
  1543. #define SOFT_PWM_SCALE 0
  1544. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1545. // be used to mitigate the associated resolution loss. If enabled,
  1546. // some of the PWM cycles are stretched so on average the desired
  1547. // duty cycle is attained.
  1548. //#define SOFT_PWM_DITHER
  1549. // Temperature status LEDs that display the hotend and bed temperature.
  1550. // If all hotends, bed temperature, and target temperature are under 54C
  1551. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1552. //#define TEMP_STAT_LEDS
  1553. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1554. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1555. //#define PHOTOGRAPH_PIN 23
  1556. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1557. //#define SF_ARC_FIX
  1558. // Support for the BariCUDA Paste Extruder
  1559. //#define BARICUDA
  1560. // Support for BlinkM/CyzRgb
  1561. //#define BLINKM
  1562. // Support for PCA9632 PWM LED driver
  1563. //#define PCA9632
  1564. /**
  1565. * RGB LED / LED Strip Control
  1566. *
  1567. * Enable support for an RGB LED connected to 5V digital pins, or
  1568. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1569. *
  1570. * Adds the M150 command to set the LED (or LED strip) color.
  1571. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1572. * luminance values can be set from 0 to 255.
  1573. * For Neopixel LED an overall brightness parameter is also available.
  1574. *
  1575. * *** CAUTION ***
  1576. * LED Strips require a MOFSET Chip between PWM lines and LEDs,
  1577. * as the Arduino cannot handle the current the LEDs will require.
  1578. * Failure to follow this precaution can destroy your Arduino!
  1579. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1580. * more current than the Arduino 5V linear regulator can produce.
  1581. * *** CAUTION ***
  1582. *
  1583. * LED Type. Enable only one of the following two options.
  1584. *
  1585. */
  1586. //#define RGB_LED
  1587. //#define RGBW_LED
  1588. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1589. #define RGB_LED_R_PIN 34
  1590. #define RGB_LED_G_PIN 43
  1591. #define RGB_LED_B_PIN 35
  1592. #define RGB_LED_W_PIN -1
  1593. #endif
  1594. // Support for Adafruit Neopixel LED driver
  1595. //#define NEOPIXEL_LED
  1596. #if ENABLED(NEOPIXEL_LED)
  1597. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1598. #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  1599. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
  1600. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1601. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1602. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1603. #endif
  1604. /**
  1605. * Printer Event LEDs
  1606. *
  1607. * During printing, the LEDs will reflect the printer status:
  1608. *
  1609. * - Gradually change from blue to violet as the heated bed gets to target temp
  1610. * - Gradually change from violet to red as the hotend gets to temperature
  1611. * - Change to white to illuminate work surface
  1612. * - Change to green once print has finished
  1613. * - Turn off after the print has finished and the user has pushed a button
  1614. */
  1615. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
  1616. #define PRINTER_EVENT_LEDS
  1617. #endif
  1618. /**
  1619. * R/C SERVO support
  1620. * Sponsored by TrinityLabs, Reworked by codexmas
  1621. */
  1622. /**
  1623. * Number of servos
  1624. *
  1625. * For some servo-related options NUM_SERVOS will be set automatically.
  1626. * Set this manually if there are extra servos needing manual control.
  1627. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1628. */
  1629. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1630. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1631. // 300ms is a good value but you can try less delay.
  1632. // If the servo can't reach the requested position, increase it.
  1633. #define SERVO_DELAY { 300 }
  1634. // Servo deactivation
  1635. //
  1636. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1637. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1638. #endif // CONFIGURATION_H