123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- *
- * Ported sys0724 & Vynt
- */
-
- /**
- * Arduino Mega? or Due with RuRAMPS4DUE pin assignments
- *
- * Applies to the following boards:
- * RURAMPS4DUE (Hotend0, Hotend1, Hotend2, Fan0, Fan1, Bed)
- *
- * Differences between
- * RADDS | RuRAMPS4DUE
- * |
- */
-
- #ifndef __SAM3X8E__
- #error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
- #endif
-
- #define BOARD_INFO_NAME "RuRAMPS4Due v1.1"
-
- //
- // Servos
- //
- #define SERVO0_PIN 5
- #define SERVO1_PIN 3
-
- //
- // Limit Switches
- //
- #define X_MIN_PIN 45
- #define X_MAX_PIN 39
- #define Y_MIN_PIN 46
- #define Y_MAX_PIN 41
- #define Z_MIN_PIN 47
- #define Z_MAX_PIN 43
-
- //
- // Z Probe (when not Z_MIN_PIN)
- //
- #ifndef Z_MIN_PROBE_PIN
- #define Z_MIN_PROBE_PIN 43
- #endif
-
- //
- // Steppers
- //
- #define X_STEP_PIN 37 // Support Extension Board
- #define X_DIR_PIN 36
- #define X_ENABLE_PIN 38
- #ifndef X_CS_PIN
- #define X_CS_PIN -1
- #endif
-
- #define Y_STEP_PIN 32 // Support Extension Board
- #define Y_DIR_PIN 35
- #define Y_ENABLE_PIN 34
- #ifndef Y_CS_PIN
- #define Y_CS_PIN -1
- #endif
-
- #define Z_STEP_PIN 30 // Support Extension Board
- #define Z_DIR_PIN 2
- #define Z_ENABLE_PIN 33
- #ifndef Z_CS_PIN
- #define Z_CS_PIN -1
- #endif
-
- #define E0_STEP_PIN 29
- #define E0_DIR_PIN 28
- #define E0_ENABLE_PIN 31
- #ifndef E0_CS_PIN
- #define E0_CS_PIN -1
- #endif
-
- #define E1_STEP_PIN 22
- #define E1_DIR_PIN 24
- #define E1_ENABLE_PIN 26
- #ifndef E1_CS_PIN
- #define E1_CS_PIN -1
- #endif
-
- #define E2_STEP_PIN 25
- #define E2_DIR_PIN 23
- #define E2_ENABLE_PIN 27
- #ifndef E2_CS_PIN
- #define E2_CS_PIN -1
- #endif
-
- #define E3_STEP_PIN 15 // Only For Extension Board
- #define E3_DIR_PIN 14
- #define E3_ENABLE_PIN 61
- #ifndef E3_CS_PIN
- #define E3_CS_PIN -1
- #endif
-
- // For Future: Microstepping pins - Mapping not from fastio.h (?)
- //#define E3_MS1_PIN ?
- //#define E3_MS2_PIN ?
- //#define E3_MS3_PIN ?
-
- #if HAS_CUSTOM_PROBE_PIN
- #define Z_MIN_PROBE_PIN 49
- #endif
-
- #if HAS_FILAMENT_SENSOR
- #ifndef FIL_RUNOUT_PIN
- #define FIL_RUNOUT_PIN Y_MIN_PIN
- #endif
- #endif
-
- //
- // Heaters / Fans
- //
- #define HEATER_0_PIN 13
- #define HEATER_1_PIN 12
- #define HEATER_2_PIN 11
- #define HEATER_BED_PIN 7 // BED H1
-
- #ifndef FAN_PIN
- #define FAN_PIN 9
- #endif
- #define FAN1_PIN 8
- #define CONTROLLER_FAN_PIN -1
-
- //
- // Temperature Sensors
- //
- #define TEMP_0_PIN 0 // ANALOG A0
- #define TEMP_1_PIN 1 // ANALOG A1
- #define TEMP_2_PIN 2 // ANALOG A2
- #define TEMP_3_PIN 3 // ANALOG A3
- #define TEMP_BED_PIN 4 // ANALOG A4
-
- // The thermocouple uses Analog pins
- #if ENABLED(VER_WITH_THERMOCOUPLE) // Defined in Configuration.h
- #define TEMP_4_PIN 5 // A5
- #define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support)
- #endif
-
- // SPI for Max6675 or Max31855 Thermocouple
- /*
- #if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
- #else
- #define MAX6675_SS_PIN 49
- #endif
- */
-
- //
- // Misc. Functions
- //
- #define SDSS 4 // 4,10,52 if using HW SPI.
- #define LED_PIN -1 // 13 - HEATER_0_PIN
- #define PS_ON_PIN -1 // 65
-
- // MKS TFT / Nextion Use internal USART-1
- #define TFT_LCD_MODULE_COM 1
- #define TFT_LCD_MODULE_BAUDRATE 115600
-
- // ESP WiFi Use internal USART-2
- #define ESP_WIFI_MODULE_COM 2
- #define ESP_WIFI_MODULE_BAUDRATE 115600
- #define ESP_WIFI_MODULE_RESET_PIN -1
- #define PIGGY_GPIO_PIN -1
-
- //
- // EEPROM
- //
- #define E2END 0x7FFF // 32Kb (24lc256)
- #define I2C_EEPROM // EEPROM on I2C-0
- //#define EEPROM_SD // EEPROM on SDCARD
- //#define SPI_EEPROM // EEPROM on SPI-0
- //#define SPI_CHAN_EEPROM1 ?
- //#define SPI_EEPROM1_CS ?
- // 2K EEPROM
- //#define SPI_EEPROM2_CS ?
- // 32Mb FLASH
- //#define SPI_FLASH_CS ?
-
- //
- // LCD / Controller
- //
- #if HAS_SPI_LCD
-
- #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
- #define BEEPER_PIN 62
- #define LCD_PINS_D4 48
- #define LCD_PINS_D5 50
- #define LCD_PINS_D6 52
- #define LCD_PINS_D7 53
- #define SD_DETECT_PIN 51
- #endif
-
- #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
-
- #define LCD_PINS_RS 63
- #define LCD_PINS_ENABLE 64
-
- #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
-
- #define LCD_PINS_RS 52
- #define LCD_PINS_ENABLE 53
-
- #elif HAS_SSD1306_OLED_I2C
-
- #define BEEPER_PIN 62
- #define LCD_SDSS 10
- #define SD_DETECT_PIN 51
-
- #elif ENABLED(FYSETC_MINI_12864)
-
- #define BEEPER_PIN 62
- #define DOGLCD_CS 64
- #define DOGLCD_A0 63
-
- //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
- // results in LCD soft SPI mode 3, SD soft SPI mode 0
-
- #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
-
- #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
- #ifndef RGB_LED_R_PIN
- #define RGB_LED_R_PIN 50 // D5
- #endif
- #ifndef RGB_LED_G_PIN
- #define RGB_LED_G_PIN 52 // D6
- #endif
- #ifndef RGB_LED_B_PIN
- #define RGB_LED_B_PIN 53 // D7
- #endif
- #elif ENABLED(FYSETC_MINI_12864_2_1)
- #define NEOPIXEL_PIN 50 // D5
- #endif
-
- #elif ENABLED(SPARK_FULL_GRAPHICS)
-
- //http://doku.radds.org/dokumentation/other-electronics/sparklcd/
- #error "Oops! SPARK_FULL_GRAPHICS not supported with RURAMPS4D."
- //#define LCD_PINS_D4 29 //?
- //#define LCD_PINS_ENABLE 27 //?
- //#define LCD_PINS_RS 25 //?
- //#define BTN_EN1 35 //?
- //#define BTN_EN2 33 //?
- //#define BTN_ENC 37 //?
-
- #endif // SPARK_FULL_GRAPHICS
-
- #if ENABLED(NEWPANEL)
- #define BTN_EN1 44
- #define BTN_EN2 42
- #define BTN_ENC 40
- #endif
-
- #endif // HAS_SPI_LCD
|