My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Ви не можете вибрати більше 25 тем Теми мають розпочинатися з літери або цифри, можуть містити дефіси (-) і не повинні перевищувати 35 символів.

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. /**
  40. *
  41. * ***********************************
  42. * ** ATTENTION TO ALL DEVELOPERS **
  43. * ***********************************
  44. *
  45. * You must increment this version number for every significant change such as,
  46. * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
  47. *
  48. * Note: Update also Version.h !
  49. */
  50. #define CONFIGURATION_H_VERSION 010100
  51. //===========================================================================
  52. //============================= Getting Started =============================
  53. //===========================================================================
  54. /**
  55. * Here are some standard links for getting your machine calibrated:
  56. *
  57. * http://reprap.org/wiki/Calibration
  58. * http://youtu.be/wAL9d7FgInk
  59. * http://calculator.josefprusa.cz
  60. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  61. * http://www.thingiverse.com/thing:5573
  62. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  63. * http://www.thingiverse.com/thing:298812
  64. */
  65. //===========================================================================
  66. //============================= DELTA Printer ===============================
  67. //===========================================================================
  68. // For a Delta printer replace the configuration files with the files in the
  69. // example_configurations/delta directory.
  70. //
  71. //===========================================================================
  72. //============================= SCARA Printer ===============================
  73. //===========================================================================
  74. // For a Scara printer replace the configuration files with the files in the
  75. // example_configurations/SCARA directory.
  76. //
  77. // @section info
  78. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  79. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  80. // build by the user have been successfully uploaded into firmware.
  81. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  82. #define SHOW_BOOTSCREEN
  83. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  84. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  85. //
  86. // *** VENDORS PLEASE READ *****************************************************
  87. //
  88. // Marlin now allow you to have a vendor boot image to be displayed on machine
  89. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  90. // custom boot image and them the default Marlin boot image is shown.
  91. //
  92. // We suggest for you to take advantage of this new feature and keep the Marlin
  93. // boot image unmodified. For an example have a look at the bq Hephestos 2
  94. // example configuration folder.
  95. //
  96. //#define SHOW_CUSTOM_BOOTSCREEN
  97. // @section machine
  98. /**
  99. * Select which serial port on the board will be used for communication with the host.
  100. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  101. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  102. *
  103. * :[0, 1, 2, 3, 4, 5, 6, 7]
  104. */
  105. #define SERIAL_PORT 0
  106. /**
  107. * This setting determines the communication speed of the printer.
  108. *
  109. * 250000 works in most cases, but you might try a lower speed if
  110. * you commonly experience drop-outs during host printing.
  111. *
  112. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
  113. */
  114. #define BAUDRATE 250000
  115. // Enable the Bluetooth serial interface on AT90USB devices
  116. //#define BLUETOOTH
  117. // The following define selects which electronics board you have.
  118. // Please choose the name from boards.h that matches your setup
  119. #ifndef MOTHERBOARD
  120. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  121. #endif
  122. // Optional custom name for your RepStrap or other custom machine
  123. // Displayed in the LCD "Ready" message
  124. //#define CUSTOM_MACHINE_NAME "3D Printer"
  125. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  126. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  127. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  128. // This defines the number of extruders
  129. // :[1, 2, 3, 4]
  130. #define EXTRUDERS 1
  131. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  132. //#define SINGLENOZZLE
  133. // A dual extruder that uses a single stepper motor
  134. // Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z
  135. //#define SWITCHING_EXTRUDER
  136. #if ENABLED(SWITCHING_EXTRUDER)
  137. #define SWITCHING_EXTRUDER_SERVO_NR 0
  138. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  139. //#define HOTEND_OFFSET_Z {0.0, 0.0}
  140. #endif
  141. /**
  142. * "Mixing Extruder"
  143. * - Adds a new code, M165, to set the current mix factors.
  144. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  145. * - Optional support for Repetier Host M163, M164, and virtual extruder.
  146. * - This implementation supports only a single extruder.
  147. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  148. */
  149. //#define MIXING_EXTRUDER
  150. #if ENABLED(MIXING_EXTRUDER)
  151. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  152. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  153. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  154. #endif
  155. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  156. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  157. // For the other hotends it is their distance from the extruder 0 hotend.
  158. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  159. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  160. /**
  161. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  162. *
  163. * 0 = No Power Switch
  164. * 1 = ATX
  165. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  166. *
  167. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  168. */
  169. #define POWER_SUPPLY 0
  170. #if POWER_SUPPLY > 0
  171. // Enable this option to leave the PSU off at startup.
  172. // Power to steppers and heaters will need to be turned on with M80.
  173. //#define PS_DEFAULT_OFF
  174. #endif
  175. // @section temperature
  176. //===========================================================================
  177. //============================= Thermal Settings ============================
  178. //===========================================================================
  179. /**
  180. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  181. *
  182. * Temperature sensors available:
  183. *
  184. * -3 : thermocouple with MAX31855 (only for sensor 0)
  185. * -2 : thermocouple with MAX6675 (only for sensor 0)
  186. * -1 : thermocouple with AD595
  187. * 0 : not used
  188. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  189. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  190. * 3 : Mendel-parts thermistor (4.7k pullup)
  191. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  192. * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  193. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  194. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  195. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  196. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  197. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  198. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  199. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  200. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  201. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  202. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  203. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  204. * 66 : 4.7M High Temperature thermistor from Dyze Design
  205. * 70 : the 100K thermistor found in the bq Hephestos 2
  206. *
  207. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  208. * (but gives greater accuracy and more stable PID)
  209. * 51 : 100k thermistor - EPCOS (1k pullup)
  210. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  211. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  212. *
  213. * 1047 : Pt1000 with 4k7 pullup
  214. * 1010 : Pt1000 with 1k pullup (non standard)
  215. * 147 : Pt100 with 4k7 pullup
  216. * 110 : Pt100 with 1k pullup (non standard)
  217. *
  218. * Use these for Testing or Development purposes. NEVER for production machine.
  219. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  220. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  221. *
  222. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  223. */
  224. #define TEMP_SENSOR_0 1
  225. #define TEMP_SENSOR_1 0
  226. #define TEMP_SENSOR_2 0
  227. #define TEMP_SENSOR_3 0
  228. #define TEMP_SENSOR_BED 0
  229. // Dummy thermistor constant temperature readings, for use with 998 and 999
  230. #define DUMMY_THERMISTOR_998_VALUE 25
  231. #define DUMMY_THERMISTOR_999_VALUE 100
  232. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  233. // from the two sensors differ too much the print will be aborted.
  234. //#define TEMP_SENSOR_1_AS_REDUNDANT
  235. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  236. // Extruder temperature must be close to target for this long before M109 returns success
  237. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  238. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  239. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  240. // Bed temperature must be close to target for this long before M190 returns success
  241. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  242. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  243. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  244. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  245. // to check that the wiring to the thermistor is not broken.
  246. // Otherwise this would lead to the heater being powered on all the time.
  247. #define HEATER_0_MINTEMP 5
  248. #define HEATER_1_MINTEMP 5
  249. #define HEATER_2_MINTEMP 5
  250. #define HEATER_3_MINTEMP 5
  251. #define BED_MINTEMP 5
  252. // When temperature exceeds max temp, your heater will be switched off.
  253. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  254. // You should use MINTEMP for thermistor short/failure protection.
  255. #define HEATER_0_MAXTEMP 275
  256. #define HEATER_1_MAXTEMP 275
  257. #define HEATER_2_MAXTEMP 275
  258. #define HEATER_3_MAXTEMP 275
  259. #define BED_MAXTEMP 150
  260. //===========================================================================
  261. //============================= PID Settings ================================
  262. //===========================================================================
  263. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  264. // Comment the following line to disable PID and enable bang-bang.
  265. #define PIDTEMP
  266. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  267. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  268. #if ENABLED(PIDTEMP)
  269. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  270. //#define PID_DEBUG // Sends debug data to the serial port.
  271. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  272. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  273. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  274. // Set/get with gcode: M301 E[extruder number, 0-2]
  275. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  276. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  277. #define K1 0.95 //smoothing factor within the PID
  278. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  279. // Ultimaker
  280. #define DEFAULT_Kp 22.2
  281. #define DEFAULT_Ki 1.08
  282. #define DEFAULT_Kd 114
  283. // MakerGear
  284. //#define DEFAULT_Kp 7.0
  285. //#define DEFAULT_Ki 0.1
  286. //#define DEFAULT_Kd 12
  287. // Mendel Parts V9 on 12V
  288. //#define DEFAULT_Kp 63.0
  289. //#define DEFAULT_Ki 2.25
  290. //#define DEFAULT_Kd 440
  291. #endif // PIDTEMP
  292. //===========================================================================
  293. //============================= PID > Bed Temperature Control ===============
  294. //===========================================================================
  295. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  296. //
  297. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  298. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  299. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  300. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  301. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  302. // shouldn't use bed PID until someone else verifies your hardware works.
  303. // If this is enabled, find your own PID constants below.
  304. //#define PIDTEMPBED
  305. //#define BED_LIMIT_SWITCHING
  306. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  307. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  308. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  309. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  310. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  311. #if ENABLED(PIDTEMPBED)
  312. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  313. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  314. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  315. #define DEFAULT_bedKp 10.00
  316. #define DEFAULT_bedKi .023
  317. #define DEFAULT_bedKd 305.4
  318. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  319. //from pidautotune
  320. //#define DEFAULT_bedKp 97.1
  321. //#define DEFAULT_bedKi 1.41
  322. //#define DEFAULT_bedKd 1675.16
  323. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  324. #endif // PIDTEMPBED
  325. // @section extruder
  326. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  327. // It also enables the M302 command to set the minimum extrusion temperature
  328. // or to allow moving the extruder regardless of the hotend temperature.
  329. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  330. #define PREVENT_COLD_EXTRUSION
  331. #define EXTRUDE_MINTEMP 170
  332. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  333. // Note that for Bowden Extruders a too-small value here may prevent loading.
  334. #define PREVENT_LENGTHY_EXTRUDE
  335. #define EXTRUDE_MAXLENGTH 200
  336. //===========================================================================
  337. //======================== Thermal Runaway Protection =======================
  338. //===========================================================================
  339. /**
  340. * Thermal Protection protects your printer from damage and fire if a
  341. * thermistor falls out or temperature sensors fail in any way.
  342. *
  343. * The issue: If a thermistor falls out or a temperature sensor fails,
  344. * Marlin can no longer sense the actual temperature. Since a disconnected
  345. * thermistor reads as a low temperature, the firmware will keep the heater on.
  346. *
  347. * If you get "Thermal Runaway" or "Heating failed" errors the
  348. * details can be tuned in Configuration_adv.h
  349. */
  350. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  351. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  352. //===========================================================================
  353. //============================= Mechanical Settings =========================
  354. //===========================================================================
  355. // @section machine
  356. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  357. // either in the usual order or reversed
  358. //#define COREXY
  359. //#define COREXZ
  360. //#define COREYZ
  361. //#define COREYX
  362. //#define COREZX
  363. //#define COREZY
  364. // Enable this option for Toshiba steppers
  365. //#define CONFIG_STEPPERS_TOSHIBA
  366. //===========================================================================
  367. //============================== Endstop Settings ===========================
  368. //===========================================================================
  369. // @section homing
  370. // Specify here all the endstop connectors that are connected to any endstop or probe.
  371. // Almost all printers will be using one per axis. Probes will use one or more of the
  372. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  373. #define USE_XMIN_PLUG
  374. #define USE_YMIN_PLUG
  375. #define USE_ZMIN_PLUG
  376. //#define USE_XMAX_PLUG
  377. //#define USE_YMAX_PLUG
  378. //#define USE_ZMAX_PLUG
  379. // coarse Endstop Settings
  380. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  381. #if DISABLED(ENDSTOPPULLUPS)
  382. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  383. //#define ENDSTOPPULLUP_XMAX
  384. //#define ENDSTOPPULLUP_YMAX
  385. //#define ENDSTOPPULLUP_ZMAX
  386. //#define ENDSTOPPULLUP_XMIN
  387. //#define ENDSTOPPULLUP_YMIN
  388. //#define ENDSTOPPULLUP_ZMIN
  389. //#define ENDSTOPPULLUP_ZMIN_PROBE
  390. #endif
  391. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  392. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  393. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  394. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  395. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  396. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  397. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  398. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  399. // Enable this feature if all enabled endstop pins are interrupt-capable.
  400. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  401. //#define ENDSTOP_INTERRUPTS_FEATURE
  402. //=============================================================================
  403. //============================== Movement Settings ============================
  404. //=============================================================================
  405. // @section motion
  406. /**
  407. * Default Settings
  408. *
  409. * These settings can be reset by M502
  410. *
  411. * Note that if EEPROM is enabled, saved values will override these.
  412. */
  413. /**
  414. * Default Axis Steps Per Unit (steps/mm)
  415. * Override with M92
  416. */
  417. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  418. /**
  419. * Default Max Feed Rate (mm/s)
  420. * Override with M203
  421. */
  422. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  423. /**
  424. * Default Max Acceleration (change/s) change = mm/s
  425. * Override with M201
  426. *
  427. * Maximum start speed for accelerated moves: { X, Y, Z, E }
  428. */
  429. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  430. /**
  431. * Default Acceleration (change/s) change = mm/s
  432. * Override with M204
  433. *
  434. * M204 P Acceleration
  435. * M204 R Retract Acceleration
  436. * M204 T Travel Acceleration
  437. */
  438. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  439. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  440. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  441. /**
  442. * Default Jerk (mm/s)
  443. *
  444. * "Jerk" specifies the minimum speed change that requires acceleration.
  445. * When changing speed and direction, if the difference is less than the
  446. * value set here, it may happen instantaneously.
  447. */
  448. #define DEFAULT_XJERK 20.0
  449. #define DEFAULT_YJERK 20.0
  450. #define DEFAULT_ZJERK 0.4
  451. #define DEFAULT_EJERK 5.0
  452. //===========================================================================
  453. //============================= Z Probe Options =============================
  454. //===========================================================================
  455. // @section probes
  456. //
  457. // Probe Type
  458. // Probes are sensors/switches that are activated / deactivated before/after use.
  459. //
  460. // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  461. // You must activate one of these to use Auto Bed Leveling below.
  462. //
  463. // Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
  464. //
  465. // A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  466. // For example an inductive probe, or a setup that uses the nozzle to probe.
  467. // An inductive probe must be deactivated to go below
  468. // its trigger-point if hardware endstops are active.
  469. //#define FIX_MOUNTED_PROBE
  470. // The BLTouch probe emulates a servo probe.
  471. // The default connector is SERVO 0. Set Z_ENDSTOP_SERVO_NR below to override.
  472. //#define BLTOUCH
  473. // Z Servo Probe, such as an endstop switch on a rotating arm.
  474. //#define Z_ENDSTOP_SERVO_NR 0
  475. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  476. // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
  477. //#define Z_PROBE_SLED
  478. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  479. // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  480. // X and Y offsets must be integers.
  481. //
  482. // In the following example the X and Y offsets are both positive:
  483. // #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  484. // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  485. //
  486. // +-- BACK ---+
  487. // | |
  488. // L | (+) P | R <-- probe (20,20)
  489. // E | | I
  490. // F | (-) N (+) | G <-- nozzle (10,10)
  491. // T | | H
  492. // | (-) | T
  493. // | |
  494. // O-- FRONT --+
  495. // (0,0)
  496. #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
  497. #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
  498. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
  499. // X and Y axis travel speed (mm/m) between probes
  500. #define XY_PROBE_SPEED 8000
  501. // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
  502. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  503. // Speed for the "accurate" probe of each point
  504. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  505. // Use double touch for probing
  506. //#define PROBE_DOUBLE_TOUCH
  507. //
  508. // Allen Key Probe is defined in the Delta example configurations.
  509. //
  510. // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
  511. //
  512. // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
  513. // Example: To park the head outside the bed area when homing with G28.
  514. //
  515. // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
  516. //
  517. // For a servo-based Z probe, you must set up servo support below, including
  518. // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
  519. //
  520. // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
  521. // - Use 5V for powered (usu. inductive) sensors.
  522. // - Otherwise connect:
  523. // - normally-closed switches to GND and D32.
  524. // - normally-open switches to 5V and D32.
  525. //
  526. // Normally-closed switches are advised and are the default.
  527. //
  528. //
  529. // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
  530. // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
  531. // default pin for all RAMPS-based boards. Most boards use the X_MAX_PIN by default.
  532. // To use a different pin you can override it here.
  533. //
  534. // WARNING:
  535. // Setting the wrong pin may have unexpected and potentially disastrous consequences.
  536. // Use with caution and do your homework.
  537. //
  538. //#define Z_MIN_PROBE_PIN X_MAX_PIN
  539. //
  540. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
  541. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
  542. //
  543. //#define Z_MIN_PROBE_ENDSTOP
  544. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
  545. // The Z_MIN_PIN will then be used for both Z-homing and probing.
  546. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  547. // To use a probe you must enable one of the two options above!
  548. // Enable Z Probe Repeatability test to see how accurate your probe is
  549. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  550. /**
  551. * Z probes require clearance when deploying, stowing, and moving between
  552. * probe points to avoid hitting the bed and other hardware.
  553. * Servo-mounted probes require extra space for the arm to rotate.
  554. * Inductive probes need space to keep from triggering early.
  555. *
  556. * Use these settings to specify the distance (mm) to raise the probe (or
  557. * lower the bed). The values set here apply over and above any (negative)
  558. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  559. * Only integer values >= 1 are valid here.
  560. *
  561. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  562. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  563. */
  564. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  565. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  566. //
  567. // For M851 give a range for adjusting the Z probe offset
  568. //
  569. #define Z_PROBE_OFFSET_RANGE_MIN -20
  570. #define Z_PROBE_OFFSET_RANGE_MAX 20
  571. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  572. // :{ 0:'Low', 1:'High' }
  573. #define X_ENABLE_ON 0
  574. #define Y_ENABLE_ON 0
  575. #define Z_ENABLE_ON 0
  576. #define E_ENABLE_ON 0 // For all extruders
  577. // Disables axis stepper immediately when it's not being used.
  578. // WARNING: When motors turn off there is a chance of losing position accuracy!
  579. #define DISABLE_X false
  580. #define DISABLE_Y false
  581. #define DISABLE_Z false
  582. // Warn on display about possibly reduced accuracy
  583. //#define DISABLE_REDUCED_ACCURACY_WARNING
  584. // @section extruder
  585. #define DISABLE_E false // For all extruders
  586. #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
  587. // @section machine
  588. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  589. #define INVERT_X_DIR false
  590. #define INVERT_Y_DIR true
  591. #define INVERT_Z_DIR false
  592. // @section extruder
  593. // For direct drive extruder v9 set to true, for geared extruder set to false.
  594. #define INVERT_E0_DIR false
  595. #define INVERT_E1_DIR false
  596. #define INVERT_E2_DIR false
  597. #define INVERT_E3_DIR false
  598. // @section homing
  599. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  600. // Be sure you have this distance over your Z_MAX_POS in case.
  601. // ENDSTOP SETTINGS:
  602. // Sets direction of endstops when homing; 1=MAX, -1=MIN
  603. // :[-1, 1]
  604. #define X_HOME_DIR -1
  605. #define Y_HOME_DIR -1
  606. #define Z_HOME_DIR -1
  607. #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
  608. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
  609. // @section machine
  610. // Travel limits after homing (units are in mm)
  611. #define X_MIN_POS 0
  612. #define Y_MIN_POS 0
  613. #define Z_MIN_POS 0
  614. #define X_MAX_POS 200
  615. #define Y_MAX_POS 200
  616. #define Z_MAX_POS 200
  617. //===========================================================================
  618. //========================= Filament Runout Sensor ==========================
  619. //===========================================================================
  620. //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
  621. // RAMPS-based boards use SERVO3_PIN. For other boards you may need to define FIL_RUNOUT_PIN.
  622. // It is assumed that when logic high = filament available
  623. // when logic low = filament ran out
  624. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  625. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  626. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  627. #define FILAMENT_RUNOUT_SCRIPT "M600"
  628. #endif
  629. //===========================================================================
  630. //============================ Mesh Bed Leveling ============================
  631. //===========================================================================
  632. //#define MESH_BED_LEVELING // Enable mesh bed leveling.
  633. #if ENABLED(MESH_BED_LEVELING)
  634. #define MESH_INSET 10 // Mesh inset margin on print area
  635. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
  636. #define MESH_NUM_Y_POINTS 3
  637. #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
  638. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
  639. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
  640. #if ENABLED(MANUAL_BED_LEVELING)
  641. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  642. #endif // MANUAL_BED_LEVELING
  643. // Gradually reduce leveling correction until a set height is reached,
  644. // at which point movement will be level to the machine's XY plane.
  645. // The height can be set with M420 Z<height>
  646. #define ENABLE_LEVELING_FADE_HEIGHT
  647. #endif // MESH_BED_LEVELING
  648. //===========================================================================
  649. //============================ Auto Bed Leveling ============================
  650. //===========================================================================
  651. // @section bedlevel
  652. /**
  653. * Select one form of Auto Bed Leveling below.
  654. *
  655. * If you're also using the Probe for Z Homing, it's
  656. * highly recommended to enable Z_SAFE_HOMING also!
  657. *
  658. * - 3POINT
  659. * Probe 3 arbitrary points on the bed (that aren't collinear)
  660. * You specify the XY coordinates of all 3 points.
  661. * The result is a single tilted plane. Best for a flat bed.
  662. *
  663. * - LINEAR
  664. * Probe several points in a grid.
  665. * You specify the rectangle and the density of sample points.
  666. * The result is a single tilted plane. Best for a flat bed.
  667. *
  668. * - BILINEAR
  669. * Probe several points in a grid.
  670. * You specify the rectangle and the density of sample points.
  671. * The result is a mesh, best for large or uneven beds.
  672. */
  673. //#define AUTO_BED_LEVELING_3POINT
  674. //#define AUTO_BED_LEVELING_LINEAR
  675. //#define AUTO_BED_LEVELING_BILINEAR
  676. /**
  677. * Enable detailed logging of G28, G29, M48, etc.
  678. * Turn on with the command 'M111 S32'.
  679. * NOTE: Requires a lot of PROGMEM!
  680. */
  681. //#define DEBUG_LEVELING_FEATURE
  682. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  683. // Set the number of grid points per dimension.
  684. #define ABL_GRID_POINTS_X 3
  685. #define ABL_GRID_POINTS_Y ABL_GRID_POINTS_X
  686. // Set the boundaries for probing (where the probe can reach).
  687. #define LEFT_PROBE_BED_POSITION 15
  688. #define RIGHT_PROBE_BED_POSITION 170
  689. #define FRONT_PROBE_BED_POSITION 20
  690. #define BACK_PROBE_BED_POSITION 170
  691. // The Z probe minimum outer margin (to validate G29 parameters).
  692. #define MIN_PROBE_EDGE 10
  693. // Probe along the Y axis, advancing X after each column
  694. //#define PROBE_Y_FIRST
  695. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  696. // Gradually reduce leveling correction until a set height is reached,
  697. // at which point movement will be level to the machine's XY plane.
  698. // The height can be set with M420 Z<height>
  699. #define ENABLE_LEVELING_FADE_HEIGHT
  700. #endif
  701. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  702. // 3 arbitrary points to probe.
  703. // A simple cross-product is used to estimate the plane of the bed.
  704. #define ABL_PROBE_PT_1_X 15
  705. #define ABL_PROBE_PT_1_Y 180
  706. #define ABL_PROBE_PT_2_X 15
  707. #define ABL_PROBE_PT_2_Y 20
  708. #define ABL_PROBE_PT_3_X 170
  709. #define ABL_PROBE_PT_3_Y 20
  710. #endif
  711. /**
  712. * Commands to execute at the end of G29 probing.
  713. * Useful to retract or move the Z probe out of the way.
  714. */
  715. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  716. // @section homing
  717. // The center of the bed is at (X=0, Y=0)
  718. //#define BED_CENTER_AT_0_0
  719. // Manually set the home position. Leave these undefined for automatic settings.
  720. // For DELTA this is the top-center of the Cartesian print volume.
  721. //#define MANUAL_X_HOME_POS 0
  722. //#define MANUAL_Y_HOME_POS 0
  723. //#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
  724. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  725. //
  726. // With this feature enabled:
  727. //
  728. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  729. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  730. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  731. // - Prevent Z homing when the Z probe is outside bed area.
  732. //#define Z_SAFE_HOMING
  733. #if ENABLED(Z_SAFE_HOMING)
  734. #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
  735. #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
  736. #endif
  737. // Homing speeds (mm/m)
  738. #define HOMING_FEEDRATE_XY (50*60)
  739. #define HOMING_FEEDRATE_Z (4*60)
  740. //=============================================================================
  741. //============================= Additional Features ===========================
  742. //=============================================================================
  743. // @section extras
  744. //
  745. // EEPROM
  746. //
  747. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  748. // M500 - stores parameters in EEPROM
  749. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  750. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  751. //define this to enable EEPROM support
  752. //#define EEPROM_SETTINGS
  753. #if ENABLED(EEPROM_SETTINGS)
  754. // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
  755. #define EEPROM_CHITCHAT // Please keep turned on if you can.
  756. #endif
  757. //
  758. // Host Keepalive
  759. //
  760. // When enabled Marlin will send a busy status message to the host
  761. // every couple of seconds when it can't accept commands.
  762. //
  763. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  764. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  765. //
  766. // M100 Free Memory Watcher
  767. //
  768. //#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
  769. //
  770. // G20/G21 Inch mode support
  771. //
  772. //#define INCH_MODE_SUPPORT
  773. //
  774. // M149 Set temperature units support
  775. //
  776. //#define TEMPERATURE_UNITS_SUPPORT
  777. // @section temperature
  778. // Preheat Constants
  779. #define PREHEAT_1_TEMP_HOTEND 180
  780. #define PREHEAT_1_TEMP_BED 70
  781. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  782. #define PREHEAT_2_TEMP_HOTEND 240
  783. #define PREHEAT_2_TEMP_BED 110
  784. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  785. //
  786. // Nozzle Park -- EXPERIMENTAL
  787. //
  788. // When enabled allows the user to define a special XYZ position, inside the
  789. // machine's topology, to park the nozzle when idle or when receiving the G27
  790. // command.
  791. //
  792. // The "P" paramenter controls what is the action applied to the Z axis:
  793. // P0: (Default) If current Z-pos is lower than Z-park then the nozzle will
  794. // be raised to reach Z-park height.
  795. //
  796. // P1: No matter the current Z-pos, the nozzle will be raised/lowered to
  797. // reach Z-park height.
  798. //
  799. // P2: The nozzle height will be raised by Z-park amount but never going over
  800. // the machine's limit of Z_MAX_POS.
  801. //
  802. //#define NOZZLE_PARK_FEATURE
  803. #if ENABLED(NOZZLE_PARK_FEATURE)
  804. // Specify a park position as { X, Y, Z }
  805. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  806. #endif
  807. //
  808. // Clean Nozzle Feature -- EXPERIMENTAL
  809. //
  810. // When enabled allows the user to send G12 to start the nozzle cleaning
  811. // process, the G-Code accepts two parameters:
  812. // "P" for pattern selection
  813. // "S" for defining the number of strokes/repetitions
  814. //
  815. // Available list of patterns:
  816. // P0: This is the default pattern, this process requires a sponge type
  817. // material at a fixed bed location, the cleaning process is based on
  818. // "strokes" i.e. back-and-forth movements between the starting and end
  819. // points.
  820. //
  821. // P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T"
  822. // defines the number of zig-zag triangles to be done. "S" defines the
  823. // number of strokes aka one back-and-forth movement. As an example
  824. // sending "G12 P1 S1 T3" will execute:
  825. //
  826. // --
  827. // | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  828. // | | / \ / \ / \ |
  829. // A | | / \ / \ / \ |
  830. // | | / \ / \ / \ |
  831. // | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  832. // -- +--------------------------------+
  833. // |________|_________|_________|
  834. // T1 T2 T3
  835. //
  836. // Caveats: End point Z should use the same value as Start point Z.
  837. //
  838. // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
  839. // may change to add new functionality like different wipe patterns.
  840. //
  841. //#define NOZZLE_CLEAN_FEATURE
  842. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  843. // Number of pattern repetitions
  844. #define NOZZLE_CLEAN_STROKES 12
  845. // Specify positions as { X, Y, Z }
  846. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  847. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  848. // Moves the nozzle to the initial position
  849. #define NOZZLE_CLEAN_GOBACK
  850. #endif
  851. //
  852. // Print job timer
  853. //
  854. // Enable this option to automatically start and stop the
  855. // print job timer when M104/M109/M190 commands are received.
  856. // M104 (extruder without wait) - high temp = none, low temp = stop timer
  857. // M109 (extruder with wait) - high temp = start timer, low temp = stop timer
  858. // M190 (bed with wait) - high temp = start timer, low temp = none
  859. //
  860. // In all cases the timer can be started and stopped using
  861. // the following commands:
  862. //
  863. // - M75 - Start the print job timer
  864. // - M76 - Pause the print job timer
  865. // - M77 - Stop the print job timer
  866. #define PRINTJOB_TIMER_AUTOSTART
  867. //
  868. // Print Counter
  869. //
  870. // When enabled Marlin will keep track of some print statistical data such as:
  871. // - Total print jobs
  872. // - Total successful print jobs
  873. // - Total failed print jobs
  874. // - Total time printing
  875. //
  876. // This information can be viewed by the M78 command.
  877. //#define PRINTCOUNTER
  878. //=============================================================================
  879. //============================= LCD and SD support ============================
  880. //=============================================================================
  881. // @section lcd
  882. //
  883. // LCD LANGUAGE
  884. //
  885. // Here you may choose the language used by Marlin on the LCD menus, the following
  886. // list of languages are available:
  887. // en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
  888. // kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, test
  889. //
  890. // :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'test':'TEST' }
  891. //
  892. #define LCD_LANGUAGE en
  893. //
  894. // LCD Character Set
  895. //
  896. // Note: This option is NOT applicable to Graphical Displays.
  897. //
  898. // All character-based LCD's provide ASCII plus one of these
  899. // language extensions:
  900. //
  901. // - JAPANESE ... the most common
  902. // - WESTERN ... with more accented characters
  903. // - CYRILLIC ... for the Russian language
  904. //
  905. // To determine the language extension installed on your controller:
  906. //
  907. // - Compile and upload with LCD_LANGUAGE set to 'test'
  908. // - Click the controller to view the LCD menu
  909. // - The LCD will display Japanese, Western, or Cyrillic text
  910. //
  911. // See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
  912. //
  913. // :['JAPANESE', 'WESTERN', 'CYRILLIC']
  914. //
  915. #define DISPLAY_CHARSET_HD44780 JAPANESE
  916. //
  917. // LCD TYPE
  918. //
  919. // You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
  920. // 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
  921. // (ST7565R family). (This option will be set automatically for certain displays.)
  922. //
  923. // IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
  924. // https://github.com/olikraus/U8glib_Arduino
  925. //
  926. //#define ULTRA_LCD // Character based
  927. //#define DOGLCD // Full graphics display
  928. //
  929. // SD CARD
  930. //
  931. // SD Card support is disabled by default. If your controller has an SD slot,
  932. // you must uncomment the following option or it won't work.
  933. //
  934. //#define SDSUPPORT
  935. //
  936. // SD CARD: SPI SPEED
  937. //
  938. // Uncomment ONE of the following items to use a slower SPI transfer
  939. // speed. This is usually required if you're getting volume init errors.
  940. //
  941. //#define SPI_SPEED SPI_HALF_SPEED
  942. //#define SPI_SPEED SPI_QUARTER_SPEED
  943. //#define SPI_SPEED SPI_EIGHTH_SPEED
  944. //
  945. // SD CARD: ENABLE CRC
  946. //
  947. // Use CRC checks and retries on the SD communication.
  948. //
  949. //#define SD_CHECK_AND_RETRY
  950. //
  951. // ENCODER SETTINGS
  952. //
  953. // This option overrides the default number of encoder pulses needed to
  954. // produce one step. Should be increased for high-resolution encoders.
  955. //
  956. //#define ENCODER_PULSES_PER_STEP 1
  957. //
  958. // Use this option to override the number of step signals required to
  959. // move between next/prev menu items.
  960. //
  961. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  962. /**
  963. * Encoder Direction Options
  964. *
  965. * Test your encoder's behavior first with both options disabled.
  966. *
  967. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  968. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  969. * Reversed Value Editing only? Enable BOTH options.
  970. */
  971. //
  972. // This option reverses the encoder direction everywhere
  973. //
  974. // Set this option if CLOCKWISE causes values to DECREASE
  975. //
  976. //#define REVERSE_ENCODER_DIRECTION
  977. //
  978. // This option reverses the encoder direction for navigating LCD menus.
  979. //
  980. // If CLOCKWISE normally moves DOWN this makes it go UP.
  981. // If CLOCKWISE normally moves UP this makes it go DOWN.
  982. //
  983. //#define REVERSE_MENU_DIRECTION
  984. //
  985. // Individual Axis Homing
  986. //
  987. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  988. //
  989. //#define INDIVIDUAL_AXIS_HOMING_MENU
  990. //
  991. // SPEAKER/BUZZER
  992. //
  993. // If you have a speaker that can produce tones, enable it here.
  994. // By default Marlin assumes you have a buzzer with a fixed frequency.
  995. //
  996. //#define SPEAKER
  997. //
  998. // The duration and frequency for the UI feedback sound.
  999. // Set these to 0 to disable audio feedback in the LCD menus.
  1000. //
  1001. // Note: Test audio output with the G-Code:
  1002. // M300 S<frequency Hz> P<duration ms>
  1003. //
  1004. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1005. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1006. //
  1007. // CONTROLLER TYPE: Standard
  1008. //
  1009. // Marlin supports a wide variety of controllers.
  1010. // Enable one of the following options to specify your controller.
  1011. //
  1012. //
  1013. // ULTIMAKER Controller.
  1014. //
  1015. //#define ULTIMAKERCONTROLLER
  1016. //
  1017. // ULTIPANEL as seen on Thingiverse.
  1018. //
  1019. //#define ULTIPANEL
  1020. //
  1021. // Cartesio UI
  1022. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1023. //
  1024. //#define CARTESIO_UI
  1025. //
  1026. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1027. // http://reprap.org/wiki/PanelOne
  1028. //
  1029. //#define PANEL_ONE
  1030. //
  1031. // MaKr3d Makr-Panel with graphic controller and SD support.
  1032. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1033. //
  1034. //#define MAKRPANEL
  1035. //
  1036. // ReprapWorld Graphical LCD
  1037. // https://reprapworld.com/?products_details&products_id/1218
  1038. //
  1039. //#define REPRAPWORLD_GRAPHICAL_LCD
  1040. //
  1041. // Activate one of these if you have a Panucatt Devices
  1042. // Viki 2.0 or mini Viki with Graphic LCD
  1043. // http://panucatt.com
  1044. //
  1045. //#define VIKI2
  1046. //#define miniVIKI
  1047. //
  1048. // Adafruit ST7565 Full Graphic Controller.
  1049. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1050. //
  1051. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1052. //
  1053. // RepRapDiscount Smart Controller.
  1054. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1055. //
  1056. // Note: Usually sold with a white PCB.
  1057. //
  1058. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1059. //
  1060. // GADGETS3D G3D LCD/SD Controller
  1061. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1062. //
  1063. // Note: Usually sold with a blue PCB.
  1064. //
  1065. //#define G3D_PANEL
  1066. //
  1067. // RepRapDiscount FULL GRAPHIC Smart Controller
  1068. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1069. //
  1070. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1071. //
  1072. // MakerLab Mini Panel with graphic
  1073. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1074. //
  1075. //#define MINIPANEL
  1076. //
  1077. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1078. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1079. //
  1080. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1081. // is pressed, a value of 10.0 means 10mm per click.
  1082. //
  1083. //#define REPRAPWORLD_KEYPAD
  1084. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1085. //
  1086. // RigidBot Panel V1.0
  1087. // http://www.inventapart.com/
  1088. //
  1089. //#define RIGIDBOT_PANEL
  1090. //
  1091. // BQ LCD Smart Controller shipped by
  1092. // default with the BQ Hephestos 2 and Witbox 2.
  1093. //
  1094. //#define BQ_LCD_SMART_CONTROLLER
  1095. //
  1096. // CONTROLLER TYPE: I2C
  1097. //
  1098. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1099. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1100. //
  1101. //
  1102. // Elefu RA Board Control Panel
  1103. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1104. //
  1105. //#define RA_CONTROL_PANEL
  1106. //
  1107. // Sainsmart YW Robot (LCM1602) LCD Display
  1108. //
  1109. //#define LCD_I2C_SAINSMART_YWROBOT
  1110. //
  1111. // Generic LCM1602 LCD adapter
  1112. //
  1113. //#define LCM1602
  1114. //
  1115. // PANELOLU2 LCD with status LEDs,
  1116. // separate encoder and click inputs.
  1117. //
  1118. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1119. // For more info: https://github.com/lincomatic/LiquidTWI2
  1120. //
  1121. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1122. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1123. //
  1124. //#define LCD_I2C_PANELOLU2
  1125. //
  1126. // Panucatt VIKI LCD with status LEDs,
  1127. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1128. //
  1129. //#define LCD_I2C_VIKI
  1130. //
  1131. // SSD1306 OLED full graphics generic display
  1132. //
  1133. //#define U8GLIB_SSD1306
  1134. //
  1135. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1136. //
  1137. //#define SAV_3DGLCD
  1138. #if ENABLED(SAV_3DGLCD)
  1139. //#define U8GLIB_SSD1306
  1140. #define U8GLIB_SH1106
  1141. #endif
  1142. //
  1143. // CONTROLLER TYPE: Shift register panels
  1144. //
  1145. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1146. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1147. //
  1148. //#define SAV_3DLCD
  1149. //=============================================================================
  1150. //=============================== Extra Features ==============================
  1151. //=============================================================================
  1152. // @section extras
  1153. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1154. //#define FAST_PWM_FAN
  1155. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1156. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1157. // is too low, you should also increment SOFT_PWM_SCALE.
  1158. //#define FAN_SOFT_PWM
  1159. // Incrementing this by 1 will double the software PWM frequency,
  1160. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1161. // However, control resolution will be halved for each increment;
  1162. // at zero value, there are 128 effective control positions.
  1163. #define SOFT_PWM_SCALE 0
  1164. // Temperature status LEDs that display the hotend and bed temperature.
  1165. // If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
  1166. // Otherwise the RED led is on. There is 1C hysteresis.
  1167. //#define TEMP_STAT_LEDS
  1168. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1169. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1170. //#define PHOTOGRAPH_PIN 23
  1171. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1172. //#define SF_ARC_FIX
  1173. // Support for the BariCUDA Paste Extruder.
  1174. //#define BARICUDA
  1175. //define BlinkM/CyzRgb Support
  1176. //#define BLINKM
  1177. /*********************************************************************\
  1178. * R/C SERVO support
  1179. * Sponsored by TrinityLabs, Reworked by codexmas
  1180. **********************************************************************/
  1181. // Number of servos
  1182. //
  1183. // If you select a configuration below, this will receive a default value and does not need to be set manually
  1184. // set it manually if you have more servos than extruders and wish to manually control some
  1185. // leaving it undefined or defining as 0 will disable the servo subsystem
  1186. // If unsure, leave commented / disabled
  1187. //
  1188. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1189. // Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
  1190. // 300ms is a good value but you can try less delay.
  1191. // If the servo can't reach the requested position, increase it.
  1192. #define SERVO_DELAY 300
  1193. // Servo deactivation
  1194. //
  1195. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1196. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1197. /**********************************************************************\
  1198. * Support for a filament diameter sensor
  1199. * Also allows adjustment of diameter at print time (vs at slicing)
  1200. * Single extruder only at this point (extruder 0)
  1201. *
  1202. * Motherboards
  1203. * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
  1204. * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
  1205. * 301 - Rambo - uses Analog input 3
  1206. * Note may require analog pins to be defined for different motherboards
  1207. **********************************************************************/
  1208. // Uncomment below to enable
  1209. //#define FILAMENT_WIDTH_SENSOR
  1210. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
  1211. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  1212. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
  1213. #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
  1214. #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
  1215. #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
  1216. #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
  1217. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
  1218. //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
  1219. //#define FILAMENT_LCD_DISPLAY
  1220. #endif
  1221. #endif // CONFIGURATION_H