123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <https://www.gnu.org/licenses/>.
- *
- */
- #pragma once
-
- /**
- * BIQU BQ111-A4
- *
- * Applies to the following boards:
- *
- * BOARD_BIQU_BQ111_A4 (Hotend, Fan, Bed)
- */
-
- #include "env_validate.h"
-
- #ifndef BOARD_INFO_NAME
- #define BOARD_INFO_NAME "BIQU Thunder B300 V1.0"
- #endif
-
- //
- // Limit Switches
- //
- #define X_MIN_PIN P1_24 // 10k pullup to 3.3V, 1K series
- #define X_MAX_PIN P1_25 // 10k pullup to 3.3V, 1K series
- #define Y_MIN_PIN P1_26 // 10k pullup to 3.3V, 1K series
- #define Y_MAX_PIN P1_27 // 10k pullup to 3.3V, 1K series
- #define Z_MIN_PIN P1_28 // 10k pullup to 3.3V, 1K series
- #define Z_MAX_PIN P1_29 // 10k pullup to 3.3V, 1K series
-
- //
- // Steppers
- //
- #define X_STEP_PIN P2_00
- #define X_DIR_PIN P0_05
- #define X_ENABLE_PIN P0_04
- #ifndef X_CS_PIN
- #define X_CS_PIN P1_15 // ETH
- #endif
-
- #define Y_STEP_PIN P2_01
- #define Y_DIR_PIN P0_11
- #define Y_ENABLE_PIN P0_10
- #ifndef Y_CS_PIN
- #define Y_CS_PIN P1_14 // ETH
- #endif
-
- #define Z_STEP_PIN P2_02
- #define Z_DIR_PIN P0_20
- #define Z_ENABLE_PIN P0_19
- #ifndef Z_CS_PIN
- #define Z_CS_PIN P1_16 // ETH
- #endif
-
- #define E0_STEP_PIN P2_03
- #define E0_DIR_PIN P0_22
- #define E0_ENABLE_PIN P0_21
- #ifndef E0_CS_PIN
- #define E0_CS_PIN P1_17 // ETH
- #endif
-
- //
- // Software SPI pins for TMC2130 stepper drivers
- //
- #if ENABLED(TMC_USE_SW_SPI)
- #ifndef TMC_SW_MOSI
- #define TMC_SW_MOSI P0_18 // ETH
- #endif
- #ifndef TMC_SW_MISO
- #define TMC_SW_MISO P0_17 // ETH
- #endif
- #ifndef TMC_SW_SCK
- #define TMC_SW_SCK P0_15 // ETH
- #endif
- #endif
-
- //
- // Temperature Sensors
- // 3.3V max when defined as an analog input
- //
- #define TEMP_0_PIN P0_24_A1 // A0 (T0)
- #define TEMP_BED_PIN P0_23_A0 // A1 (T1)
-
- //
- // Heaters / Fans
- //
- #define HEATER_0_PIN P2_07
- #define HEATER_BED_PIN P2_05
- #ifndef FAN_PIN
- #define FAN_PIN P2_04
- #endif
-
- //
- // Unused
- //
- //#define PIN_P2_10 P2_10 // IBOOT-1
- //#define PIN_P0_27 P0_27 // Onboard SD Detect
-
- /**
- * LCD / Controller
- *
- * REPRAP_DISCOUNT_SMART_CONTROLLER is not supported due to the lack of LCD_PINS_D5,
- * LCD_PINS_D6 or LCD_PINS_D7 in the EXP1 connector.
- *
- * A remote SD card is not supported as the pins routed to EXP2 are the same as used
- * for the onboard SD card, and a chip select signal is not provided for the remote
- * SD card.
- */
- #if HAS_WIRED_LCD
-
- #define BEEPER_PIN P1_31 // EXP1-1
-
- #define BTN_EN1 P3_26 // EXP2-3
- #define BTN_EN2 P3_25 // EXP2-5
- #define BTN_ENC P1_30 // EXP1-2
-
- #define SD_DETECT_PIN P0_27 // EXP2-7
- #define LCD_PINS_RS P0_16 // EXP1-4
- #define LCD_PINS_ENABLE P0_18 // (MOSI) EXP1-3
- #define LCD_PINS_D4 P0_15 // (SCK) EXP1-5
-
- #if BOTH(HAS_MARLINUI_HD44780, IS_RRD_SC)
- #error "REPRAP_DISCOUNT_SMART_CONTROLLER displays aren't supported by the BIQU B300 v1.0"
- #endif
-
- #if ENABLED(SDSUPPORT)
- #error "SDSUPPORT is not supported by the BIQU B300 v1.0 when an LCD controller is used"
- #endif
-
- #endif // HAS_WIRED_LCD
-
- /**
- * SD Card Reader
- *
- * Software SPI is used to interface with a stand-alone SD card reader connected to EXP1.
- * Hardware SPI can't be used because P0_17 (MISO) is not brought out on this board.
- */
- #if ENABLED(SDSUPPORT)
- #define SD_SCK_PIN P0_15 // EXP1-5
- #define SD_MISO_PIN P0_16 // EXP1-4
- #define SD_MOSI_PIN P0_18 // EXP1-3
- #define SD_SS_PIN P1_30 // EXP1-2
- #define SDSS SD_SS_PIN
- #endif
-
- /**
- * PWMS
- *
- * There are 6 PWMS. Each PWM can be assigned to one of two pins.
- *
- * PWM1.1 P0_18 LCD_PINS_ENABLE
- * PWM1.1 P2_0 X_STEP_PIN
- * PWM1.2 P1_20 <none>
- * PWM1.2 P2_1 Y_STEP_PIN
- * PWM1.3 P1_21 <none>
- * PWM1.3 P2_2 Z_STEP_PIN
- * PWM1.4 P1_23 <none>
- * PWM1.4 P2_3 E0_STEP_PIN
- * PWM1.5 P1_24 X_MIN_PIN
- * PWM1.5 P2_4 FAN_PIN
- * PWM1.6 P1_26 Y_MIN_PIN
- * PWM1.6 P2_5 HEATER_BED_PIN
- */
|