12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- *
- */
-
- /**
- * AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments
- */
-
- #ifndef __AVR_ATmega2560__
- #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
- #endif
-
- #if HOTENDS > 2 || E_STEPPERS > 2
- #error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
- #endif
-
- #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
- #define CASE_LIGHT_PIN 6 // Define before RAMPS pins include
- #endif
- #define BOARD_NAME "Azteeg X3"
-
- //
- // Servos
- //
- #define SERVO0_PIN 44 // SERVO1 port
- #define SERVO1_PIN 55 // SERVO2 port
-
- #include "pins_RAMPS_13.h"
-
- //
- // LCD / Controller
- //
- #undef STAT_LED_RED_PIN
- #undef STAT_LED_BLUE_PIN
-
- #if ANY(VIKI2, miniVIKI)
-
- #undef DOGLCD_A0
- #undef DOGLCD_CS
- #undef BTN_ENC
- #define DOGLCD_A0 31
- #define DOGLCD_CS 32
- #define BTN_ENC 12
-
- #define STAT_LED_RED_PIN 64
- #define STAT_LED_BLUE_PIN 63
-
- #else
-
- #define STAT_LED_RED_PIN 6
- #define STAT_LED_BLUE_PIN 11
-
- #endif
-
- //
- // Misc
- //
- #if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT, STAT_LED_RED) && STAT_LED_RED_PIN == CASE_LIGHT_PIN
- #undef STAT_LED_RED_PIN
- #endif
-
- //
- // M3/M4/M5 - Spindle/Laser Control
- //
- #undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
- #undef SPINDLE_LASER_ENA_PIN
- #undef SPINDLE_DIR_PIN
-
- #if HAS_CUTTER
- #undef SDA // use EXP3 header
- #undef SCL
- #if SERVO0_PIN == 7
- #undef SERVO0_PIN
- #define SERVO0_PIN 11
- #endif
- #define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM
- #define SPINDLE_LASER_ENA_PIN 20 // Pin should have a pullup!
- #define SPINDLE_DIR_PIN 21
- #endif
|