123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- *
- */
-
- /**
- * RAMPS-FD
- *
- * No EEPROM
- * Use 4k7 thermistor tables
- */
-
- #ifndef __SAM3X8E__
- #error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
- #endif
-
- #ifndef BOARD_NAME
- #define BOARD_NAME "RAMPS-FD v1"
- #endif
-
- #define INVERTED_HEATER_PINS
- #define INVERTED_BED_PINS
- #define INVERTED_FAN_PINS
-
- //
- // Servos
- //
- #define SERVO0_PIN 7
- #define SERVO1_PIN 6
- #define SERVO2_PIN 5
- #define SERVO3_PIN 3
-
- //
- // Limit Switches
- //
- #define X_MIN_PIN 22
- #define X_MAX_PIN 30
- #define Y_MIN_PIN 24
- #define Y_MAX_PIN 38
- #define Z_MIN_PIN 26
- #define Z_MAX_PIN 34
-
- //
- // Steppers
- //
- #define X_STEP_PIN 63
- #define X_DIR_PIN 62
- #define X_ENABLE_PIN 48
- #ifndef X_CS_PIN
- #define X_CS_PIN 68
- #endif
-
- #define Y_STEP_PIN 65
- #define Y_DIR_PIN 64
- #define Y_ENABLE_PIN 46
- #ifndef Y_CS_PIN
- #define Y_CS_PIN 60
- #endif
-
- #define Z_STEP_PIN 67
- #define Z_DIR_PIN 66
- #define Z_ENABLE_PIN 44
- #ifndef Z_CS_PIN
- #define Z_CS_PIN 58
- #endif
-
- #define E0_STEP_PIN 36
- #define E0_DIR_PIN 28
- #define E0_ENABLE_PIN 42
- #ifndef E0_CS_PIN
- #define E0_CS_PIN 67
- #endif
-
- #define E1_STEP_PIN 43
- #define E1_DIR_PIN 41
- #define E1_ENABLE_PIN 39
- #ifndef E1_CS_PIN
- #define E1_CS_PIN 61
- #endif
-
- #define E2_STEP_PIN 32
- #define E2_DIR_PIN 47
- #define E2_ENABLE_PIN 45
- #ifndef E2_CS_PIN
- #define E2_CS_PIN 59
- #endif
-
- //
- // Temperature Sensors
- //
- #define TEMP_0_PIN 1 // Analog Input
- #define TEMP_1_PIN 2 // Analog Input
- #define TEMP_2_PIN 3 // Analog Input
- #define TEMP_BED_PIN 0 // Analog Input
-
- // SPI for Max6675 or Max31855 Thermocouple
- #if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
- #else
- #define MAX6675_SS_PIN 49
- #endif
-
- //
- // Heaters / Fans
- //
- #define HEATER_0_PIN 9
- #define HEATER_1_PIN 10
- #define HEATER_2_PIN 11
- #define HEATER_BED_PIN 8
-
- #ifndef FAN_PIN
- #define FAN_PIN 12
- #endif
-
- //
- // Misc. Functions
- //
- #define SDSS 4
- #define LED_PIN 13
-
- //
- // LCD / Controller
- //
- #if HAS_SPI_LCD
- // ramps-fd lcd adaptor
-
- #define BEEPER_PIN 37
- #define BTN_EN1 33
- #define BTN_EN2 31
- #define BTN_ENC 35
- #define SD_DETECT_PIN 49
-
- #if ENABLED(NEWPANEL)
- #define LCD_PINS_RS 16
- #define LCD_PINS_ENABLE 17
- #endif
-
- #if ENABLED(FYSETC_MINI_12864)
- #define DOGLCD_CS LCD_PINS_ENABLE
- #define DOGLCD_A0 LCD_PINS_RS
- #define DOGLCD_SCK 76
- #define DOGLCD_MOSI 75
-
- //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
- // results in LCD soft SPI mode 3, SD soft SPI mode 0
-
- #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
-
- #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
- #ifndef RGB_LED_R_PIN
- #define RGB_LED_R_PIN 25
- #endif
- #ifndef RGB_LED_G_PIN
- #define RGB_LED_G_PIN 27
- #endif
- #ifndef RGB_LED_B_PIN
- #define RGB_LED_B_PIN 29
- #endif
- #elif ENABLED(FYSETC_MINI_12864_2_1)
- #define NEOPIXEL_PIN 25
- #endif
-
- #elif ENABLED(NEWPANEL)
-
- #define LCD_PINS_D4 23
- #define LCD_PINS_D5 25
- #define LCD_PINS_D6 27
- #define LCD_PINS_D7 29
-
- #if ENABLED(MINIPANEL)
- #define DOGLCD_CS 25
- #define DOGLCD_A0 27
- #endif
-
- #endif
-
- #if ANY(VIKI2, miniVIKI)
- #define DOGLCD_A0 16
- #define KILL_PIN 51
- #define STAT_LED_BLUE_PIN 29
- #define STAT_LED_RED_PIN 23
- #define DOGLCD_CS 17
- #define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI
- #define DOGLCD_MOSI 75 // MOSI_PIN
- #define DOGLCD_MISO 74 // MISO_PIN
- #endif
-
- #endif // HAS_SPI_LCD
-
- #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)
- /**
- * TMC2208/TMC2209 stepper drivers
- *
- * Hardware serial communication ports.
- * If undefined software serial is used according to the pins below
- */
- //#define X_HARDWARE_SERIAL Serial1
- //#define X2_HARDWARE_SERIAL Serial1
- //#define Y_HARDWARE_SERIAL Serial1
- //#define Y2_HARDWARE_SERIAL Serial1
- //#define Z_HARDWARE_SERIAL Serial1
- //#define Z2_HARDWARE_SERIAL Serial1
- //#define E0_HARDWARE_SERIAL Serial1
- //#define E1_HARDWARE_SERIAL Serial1
- //#define E2_HARDWARE_SERIAL Serial1
- //#define E3_HARDWARE_SERIAL Serial1
- //#define E4_HARDWARE_SERIAL Serial1
- #endif
-
- //
- // M3/M4/M5 - Spindle/Laser Control
- //
- #if HOTENDS < 3 && HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA)
- #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA
- #define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM
- #define SPINDLE_DIR_PIN 47 // Use E2 DIR
- #endif
|