My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 63KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497149814991500150115021503150415051506150715081509151015111512151315141515151615171518151915201521152215231524152515261527152815291530153115321533153415351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563156415651566156715681569157015711572157315741575157615771578157915801581158215831584158515861587158815891590159115921593159415951596159715981599160016011602160316041605160616071608160916101611161216131614161516161617161816191620162116221623162416251626162716281629163016311632163316341635163616371638163916401641164216431644164516461647164816491650165116521653165416551656165716581659166016611662166316641665166616671668166916701671167216731674167516761677167816791680168116821683168416851686168716881689169016911692169316941695169616971698169917001701170217031704170517061707170817091710171117121713171417151716171717181719172017211722172317241725172617271728
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. #define CONFIGURATION_H_VERSION 020000
  40. //===========================================================================
  41. //============================= Getting Started =============================
  42. //===========================================================================
  43. /**
  44. * Here are some standard links for getting your machine calibrated:
  45. *
  46. * http://reprap.org/wiki/Calibration
  47. * http://youtu.be/wAL9d7FgInk
  48. * http://calculator.josefprusa.cz
  49. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  50. * http://www.thingiverse.com/thing:5573
  51. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  52. * http://www.thingiverse.com/thing:298812
  53. */
  54. //===========================================================================
  55. //============================= DELTA Printer ===============================
  56. //===========================================================================
  57. // For a Delta printer start with one of the configuration files in the
  58. // config/examples/delta directory and customize for your machine.
  59. //
  60. //===========================================================================
  61. //============================= SCARA Printer ===============================
  62. //===========================================================================
  63. // For a SCARA printer start with the configuration files in
  64. // config/examples/SCARA and customize for your machine.
  65. //
  66. // @section info
  67. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  68. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  69. // build by the user have been successfully uploaded into firmware.
  70. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  71. #define SHOW_BOOTSCREEN
  72. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  73. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  74. //
  75. // *** VENDORS PLEASE READ *****************************************************
  76. //
  77. // Marlin now allow you to have a vendor boot image to be displayed on machine
  78. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  79. // custom boot image and then the default Marlin boot image is shown.
  80. //
  81. // We suggest for you to take advantage of this new feature and keep the Marlin
  82. // boot image unmodified. For an example have a look at the bq Hephestos 2
  83. // example configuration folder.
  84. //
  85. //#define SHOW_CUSTOM_BOOTSCREEN
  86. // @section machine
  87. /**
  88. * Select the serial port on the board to use for communication with the host.
  89. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  90. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  91. *
  92. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  93. */
  94. #define SERIAL_PORT 0
  95. /**
  96. * This setting determines the communication speed of the printer.
  97. *
  98. * 250000 works in most cases, but you might try a lower speed if
  99. * you commonly experience drop-outs during host printing.
  100. * You may try up to 1000000 to speed up SD file transfer.
  101. *
  102. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  103. */
  104. #define BAUDRATE 250000
  105. // Enable the Bluetooth serial interface on AT90USB devices
  106. //#define BLUETOOTH
  107. // The following define selects which electronics board you have.
  108. // Please choose the name from boards.h that matches your setup
  109. #ifndef MOTHERBOARD
  110. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  111. #endif
  112. // Optional custom name for your RepStrap or other custom machine
  113. // Displayed in the LCD "Ready" message
  114. //#define CUSTOM_MACHINE_NAME "3D Printer"
  115. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  116. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  117. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  118. // @section extruder
  119. // This defines the number of extruders
  120. // :[1, 2, 3, 4, 5]
  121. #define EXTRUDERS 1
  122. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  123. //#define SINGLENOZZLE
  124. /**
  125. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  126. *
  127. * This device allows one stepper driver on a control board to drive
  128. * two to eight stepper motors, one at a time, in a manner suitable
  129. * for extruders.
  130. *
  131. * This option only allows the multiplexer to switch on tool-change.
  132. * Additional options to configure custom E moves are pending.
  133. */
  134. //#define MK2_MULTIPLEXER
  135. #if ENABLED(MK2_MULTIPLEXER)
  136. // Override the default DIO selector pins here, if needed.
  137. // Some pins files may provide defaults for these pins.
  138. //#define E_MUX0_PIN 40 // Always Required
  139. //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers
  140. //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers
  141. #endif
  142. // A dual extruder that uses a single stepper motor
  143. //#define SWITCHING_EXTRUDER
  144. #if ENABLED(SWITCHING_EXTRUDER)
  145. #define SWITCHING_EXTRUDER_SERVO_NR 0
  146. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  147. #if EXTRUDERS > 3
  148. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  149. #endif
  150. #endif
  151. // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
  152. //#define SWITCHING_NOZZLE
  153. #if ENABLED(SWITCHING_NOZZLE)
  154. #define SWITCHING_NOZZLE_SERVO_NR 0
  155. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  156. //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
  157. #endif
  158. /**
  159. * Two separate X-carriages with extruders that connect to a moving part
  160. * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  161. */
  162. //#define PARKING_EXTRUDER
  163. #if ENABLED(PARKING_EXTRUDER)
  164. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  165. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  166. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
  167. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  168. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
  169. #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking
  170. #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.
  171. #endif
  172. /**
  173. * "Mixing Extruder"
  174. * - Adds a new code, M165, to set the current mix factors.
  175. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  176. * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  177. * - This implementation supports only a single extruder.
  178. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  179. */
  180. //#define MIXING_EXTRUDER
  181. #if ENABLED(MIXING_EXTRUDER)
  182. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  183. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  184. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  185. #endif
  186. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  187. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  188. // For the other hotends it is their distance from the extruder 0 hotend.
  189. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  190. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  191. // @section machine
  192. /**
  193. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  194. *
  195. * 0 = No Power Switch
  196. * 1 = ATX
  197. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  198. *
  199. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  200. */
  201. #define POWER_SUPPLY 0
  202. #if POWER_SUPPLY > 0
  203. // Enable this option to leave the PSU off at startup.
  204. // Power to steppers and heaters will need to be turned on with M80.
  205. //#define PS_DEFAULT_OFF
  206. #endif
  207. // @section temperature
  208. //===========================================================================
  209. //============================= Thermal Settings ============================
  210. //===========================================================================
  211. /**
  212. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  213. *
  214. * Temperature sensors available:
  215. *
  216. * -3 : thermocouple with MAX31855 (only for sensor 0)
  217. * -2 : thermocouple with MAX6675 (only for sensor 0)
  218. * -1 : thermocouple with AD595
  219. * 0 : not used
  220. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  221. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  222. * 3 : Mendel-parts thermistor (4.7k pullup)
  223. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  224. * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  225. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  226. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  227. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  228. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  229. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  230. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  231. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  232. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  233. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  234. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  235. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  236. * 66 : 4.7M High Temperature thermistor from Dyze Design
  237. * 70 : the 100K thermistor found in the bq Hephestos 2
  238. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  239. *
  240. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  241. * (but gives greater accuracy and more stable PID)
  242. * 51 : 100k thermistor - EPCOS (1k pullup)
  243. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  244. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  245. *
  246. * 1047 : Pt1000 with 4k7 pullup
  247. * 1010 : Pt1000 with 1k pullup (non standard)
  248. * 147 : Pt100 with 4k7 pullup
  249. * 110 : Pt100 with 1k pullup (non standard)
  250. *
  251. * Use these for Testing or Development purposes. NEVER for production machine.
  252. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  253. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  254. *
  255. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  256. */
  257. #define TEMP_SENSOR_0 1
  258. #define TEMP_SENSOR_1 0
  259. #define TEMP_SENSOR_2 0
  260. #define TEMP_SENSOR_3 0
  261. #define TEMP_SENSOR_4 0
  262. #define TEMP_SENSOR_BED 0
  263. // Dummy thermistor constant temperature readings, for use with 998 and 999
  264. #define DUMMY_THERMISTOR_998_VALUE 25
  265. #define DUMMY_THERMISTOR_999_VALUE 100
  266. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  267. // from the two sensors differ too much the print will be aborted.
  268. //#define TEMP_SENSOR_1_AS_REDUNDANT
  269. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  270. // Extruder temperature must be close to target for this long before M109 returns success
  271. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  272. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  273. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  274. // Bed temperature must be close to target for this long before M190 returns success
  275. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  276. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  277. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  278. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  279. // to check that the wiring to the thermistor is not broken.
  280. // Otherwise this would lead to the heater being powered on all the time.
  281. #define HEATER_0_MINTEMP 5
  282. #define HEATER_1_MINTEMP 5
  283. #define HEATER_2_MINTEMP 5
  284. #define HEATER_3_MINTEMP 5
  285. #define HEATER_4_MINTEMP 5
  286. #define BED_MINTEMP 5
  287. // When temperature exceeds max temp, your heater will be switched off.
  288. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  289. // You should use MINTEMP for thermistor short/failure protection.
  290. #define HEATER_0_MAXTEMP 275
  291. #define HEATER_1_MAXTEMP 275
  292. #define HEATER_2_MAXTEMP 275
  293. #define HEATER_3_MAXTEMP 275
  294. #define HEATER_4_MAXTEMP 275
  295. #define BED_MAXTEMP 150
  296. //===========================================================================
  297. //============================= PID Settings ================================
  298. //===========================================================================
  299. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  300. // Comment the following line to disable PID and enable bang-bang.
  301. #define PIDTEMP
  302. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  303. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  304. #if ENABLED(PIDTEMP)
  305. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  306. //#define PID_DEBUG // Sends debug data to the serial port.
  307. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  308. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  309. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  310. // Set/get with gcode: M301 E[extruder number, 0-2]
  311. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  312. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  313. #define K1 0.95 //smoothing factor within the PID
  314. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  315. // Ultimaker
  316. #define DEFAULT_Kp 22.2
  317. #define DEFAULT_Ki 1.08
  318. #define DEFAULT_Kd 114
  319. // MakerGear
  320. //#define DEFAULT_Kp 7.0
  321. //#define DEFAULT_Ki 0.1
  322. //#define DEFAULT_Kd 12
  323. // Mendel Parts V9 on 12V
  324. //#define DEFAULT_Kp 63.0
  325. //#define DEFAULT_Ki 2.25
  326. //#define DEFAULT_Kd 440
  327. #endif // PIDTEMP
  328. //===========================================================================
  329. //============================= PID > Bed Temperature Control ===============
  330. //===========================================================================
  331. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  332. //
  333. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  334. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  335. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  336. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  337. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  338. // shouldn't use bed PID until someone else verifies your hardware works.
  339. // If this is enabled, find your own PID constants below.
  340. //#define PIDTEMPBED
  341. //#define BED_LIMIT_SWITCHING
  342. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  343. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  344. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  345. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  346. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  347. #if ENABLED(PIDTEMPBED)
  348. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  349. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  350. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  351. #define DEFAULT_bedKp 10.00
  352. #define DEFAULT_bedKi .023
  353. #define DEFAULT_bedKd 305.4
  354. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  355. //from pidautotune
  356. //#define DEFAULT_bedKp 97.1
  357. //#define DEFAULT_bedKi 1.41
  358. //#define DEFAULT_bedKd 1675.16
  359. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  360. #endif // PIDTEMPBED
  361. // @section extruder
  362. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  363. // It also enables the M302 command to set the minimum extrusion temperature
  364. // or to allow moving the extruder regardless of the hotend temperature.
  365. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  366. #define PREVENT_COLD_EXTRUSION
  367. #define EXTRUDE_MINTEMP 170
  368. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  369. // Note that for Bowden Extruders a too-small value here may prevent loading.
  370. #define PREVENT_LENGTHY_EXTRUDE
  371. #define EXTRUDE_MAXLENGTH 200
  372. //===========================================================================
  373. //======================== Thermal Runaway Protection =======================
  374. //===========================================================================
  375. /**
  376. * Thermal Protection protects your printer from damage and fire if a
  377. * thermistor falls out or temperature sensors fail in any way.
  378. *
  379. * The issue: If a thermistor falls out or a temperature sensor fails,
  380. * Marlin can no longer sense the actual temperature. Since a disconnected
  381. * thermistor reads as a low temperature, the firmware will keep the heater on.
  382. *
  383. * If you get "Thermal Runaway" or "Heating failed" errors the
  384. * details can be tuned in Configuration_adv.h
  385. */
  386. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  387. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  388. //===========================================================================
  389. //============================= Mechanical Settings =========================
  390. //===========================================================================
  391. // @section machine
  392. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  393. // either in the usual order or reversed
  394. //#define COREXY
  395. //#define COREXZ
  396. //#define COREYZ
  397. //#define COREYX
  398. //#define COREZX
  399. //#define COREZY
  400. //===========================================================================
  401. //============================== Endstop Settings ===========================
  402. //===========================================================================
  403. // @section homing
  404. // Specify here all the endstop connectors that are connected to any endstop or probe.
  405. // Almost all printers will be using one per axis. Probes will use one or more of the
  406. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  407. #define USE_XMIN_PLUG
  408. #define USE_YMIN_PLUG
  409. #define USE_ZMIN_PLUG
  410. //#define USE_XMAX_PLUG
  411. //#define USE_YMAX_PLUG
  412. //#define USE_ZMAX_PLUG
  413. // coarse Endstop Settings
  414. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  415. #if DISABLED(ENDSTOPPULLUPS)
  416. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  417. //#define ENDSTOPPULLUP_XMAX
  418. //#define ENDSTOPPULLUP_YMAX
  419. //#define ENDSTOPPULLUP_ZMAX
  420. //#define ENDSTOPPULLUP_XMIN
  421. //#define ENDSTOPPULLUP_YMIN
  422. //#define ENDSTOPPULLUP_ZMIN
  423. //#define ENDSTOPPULLUP_ZMIN_PROBE
  424. #endif
  425. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  426. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  427. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  428. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  429. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  430. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  431. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  432. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
  433. // Enable this feature if all enabled endstop pins are interrupt-capable.
  434. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  435. //#define ENDSTOP_INTERRUPTS_FEATURE
  436. //=============================================================================
  437. //============================== Movement Settings ============================
  438. //=============================================================================
  439. // @section motion
  440. /**
  441. * Default Settings
  442. *
  443. * These settings can be reset by M502
  444. *
  445. * Note that if EEPROM is enabled, saved values will override these.
  446. */
  447. /**
  448. * With this option each E stepper can have its own factors for the
  449. * following movement settings. If fewer factors are given than the
  450. * total number of extruders, the last value applies to the rest.
  451. */
  452. //#define DISTINCT_E_FACTORS
  453. /**
  454. * Default Axis Steps Per Unit (steps/mm)
  455. * Override with M92
  456. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  457. */
  458. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  459. /**
  460. * Default Max Feed Rate (mm/s)
  461. * Override with M203
  462. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  463. */
  464. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  465. /**
  466. * Default Max Acceleration (change/s) change = mm/s
  467. * (Maximum start speed for accelerated moves)
  468. * Override with M201
  469. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  470. */
  471. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  472. /**
  473. * Default Acceleration (change/s) change = mm/s
  474. * Override with M204
  475. *
  476. * M204 P Acceleration
  477. * M204 R Retract Acceleration
  478. * M204 T Travel Acceleration
  479. */
  480. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  481. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  482. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  483. /**
  484. * Default Jerk (mm/s)
  485. * Override with M205 X Y Z E
  486. *
  487. * "Jerk" specifies the minimum speed change that requires acceleration.
  488. * When changing speed and direction, if the difference is less than the
  489. * value set here, it may happen instantaneously.
  490. */
  491. #define DEFAULT_XJERK 20.0
  492. #define DEFAULT_YJERK 20.0
  493. #define DEFAULT_ZJERK 0.4
  494. #define DEFAULT_EJERK 5.0
  495. //===========================================================================
  496. //============================= Z Probe Options =============================
  497. //===========================================================================
  498. // @section probes
  499. //
  500. // See http://marlinfw.org/docs/configuration/probes.html
  501. //
  502. /**
  503. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  504. *
  505. * Enable this option for a probe connected to the Z Min endstop pin.
  506. */
  507. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  508. /**
  509. * Z_MIN_PROBE_ENDSTOP
  510. *
  511. * Enable this option for a probe connected to any pin except Z-Min.
  512. * (By default Marlin assumes the Z-Max endstop pin.)
  513. * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  514. *
  515. * - The simplest option is to use a free endstop connector.
  516. * - Use 5V for powered (usually inductive) sensors.
  517. *
  518. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  519. * - For simple switches connect...
  520. * - normally-closed switches to GND and D32.
  521. * - normally-open switches to 5V and D32.
  522. *
  523. * WARNING: Setting the wrong pin may have unexpected and potentially
  524. * disastrous consequences. Use with caution and do your homework.
  525. *
  526. */
  527. //#define Z_MIN_PROBE_ENDSTOP
  528. /**
  529. * Probe Type
  530. *
  531. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  532. * Activate one of these to use Auto Bed Leveling below.
  533. */
  534. /**
  535. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  536. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  537. * or (with LCD_BED_LEVELING) the LCD controller.
  538. */
  539. //#define PROBE_MANUALLY
  540. /**
  541. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  542. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  543. */
  544. //#define FIX_MOUNTED_PROBE
  545. /**
  546. * Z Servo Probe, such as an endstop switch on a rotating arm.
  547. */
  548. //#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
  549. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  550. /**
  551. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  552. */
  553. //#define BLTOUCH
  554. #if ENABLED(BLTOUCH)
  555. //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
  556. #endif
  557. /**
  558. * Enable one or more of the following if probing seems unreliable.
  559. * Heaters and/or fans can be disabled during probing to minimize electrical
  560. * noise. A delay can also be added to allow noise and vibration to settle.
  561. * These options are most useful for the BLTouch probe, but may also improve
  562. * readings with inductive probes and piezo sensors.
  563. */
  564. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  565. //#define PROBING_FANS_OFF // Turn fans off when probing
  566. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  567. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  568. //#define SOLENOID_PROBE
  569. // A sled-mounted probe like those designed by Charles Bell.
  570. //#define Z_PROBE_SLED
  571. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  572. //
  573. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  574. //
  575. /**
  576. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  577. * X and Y offsets must be integers.
  578. *
  579. * In the following example the X and Y offsets are both positive:
  580. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  581. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  582. *
  583. * +-- BACK ---+
  584. * | |
  585. * L | (+) P | R <-- probe (20,20)
  586. * E | | I
  587. * F | (-) N (+) | G <-- nozzle (10,10)
  588. * T | | H
  589. * | (-) | T
  590. * | |
  591. * O-- FRONT --+
  592. * (0,0)
  593. */
  594. #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
  595. #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
  596. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
  597. // X and Y axis travel speed (mm/m) between probes
  598. #define XY_PROBE_SPEED 8000
  599. // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
  600. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  601. // Speed for the "accurate" probe of each point
  602. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  603. // Use double touch for probing
  604. //#define PROBE_DOUBLE_TOUCH
  605. /**
  606. * Z probes require clearance when deploying, stowing, and moving between
  607. * probe points to avoid hitting the bed and other hardware.
  608. * Servo-mounted probes require extra space for the arm to rotate.
  609. * Inductive probes need space to keep from triggering early.
  610. *
  611. * Use these settings to specify the distance (mm) to raise the probe (or
  612. * lower the bed). The values set here apply over and above any (negative)
  613. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  614. * Only integer values >= 1 are valid here.
  615. *
  616. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  617. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  618. */
  619. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  620. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  621. // For M851 give a range for adjusting the Z probe offset
  622. #define Z_PROBE_OFFSET_RANGE_MIN -20
  623. #define Z_PROBE_OFFSET_RANGE_MAX 20
  624. // Enable the M48 repeatability test to test probe accuracy
  625. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  626. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  627. // :{ 0:'Low', 1:'High' }
  628. #define X_ENABLE_ON 0
  629. #define Y_ENABLE_ON 0
  630. #define Z_ENABLE_ON 0
  631. #define E_ENABLE_ON 0 // For all extruders
  632. // Disables axis stepper immediately when it's not being used.
  633. // WARNING: When motors turn off there is a chance of losing position accuracy!
  634. #define DISABLE_X false
  635. #define DISABLE_Y false
  636. #define DISABLE_Z false
  637. // Warn on display about possibly reduced accuracy
  638. //#define DISABLE_REDUCED_ACCURACY_WARNING
  639. // @section extruder
  640. #define DISABLE_E false // For all extruders
  641. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  642. // @section machine
  643. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  644. #define INVERT_X_DIR false
  645. #define INVERT_Y_DIR true
  646. #define INVERT_Z_DIR false
  647. // Enable this option for Toshiba stepper drivers
  648. //#define CONFIG_STEPPERS_TOSHIBA
  649. // @section extruder
  650. // For direct drive extruder v9 set to true, for geared extruder set to false.
  651. #define INVERT_E0_DIR false
  652. #define INVERT_E1_DIR false
  653. #define INVERT_E2_DIR false
  654. #define INVERT_E3_DIR false
  655. #define INVERT_E4_DIR false
  656. // @section homing
  657. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  658. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  659. // Be sure you have this distance over your Z_MAX_POS in case.
  660. // Direction of endstops when homing; 1=MAX, -1=MIN
  661. // :[-1,1]
  662. #define X_HOME_DIR -1
  663. #define Y_HOME_DIR -1
  664. #define Z_HOME_DIR -1
  665. // @section machine
  666. // The size of the print bed
  667. #define X_BED_SIZE 200
  668. #define Y_BED_SIZE 200
  669. // Travel limits (mm) after homing, corresponding to endstop positions.
  670. #define X_MIN_POS 0
  671. #define Y_MIN_POS 0
  672. #define Z_MIN_POS 0
  673. #define X_MAX_POS X_BED_SIZE
  674. #define Y_MAX_POS Y_BED_SIZE
  675. #define Z_MAX_POS 200
  676. /**
  677. * Software Endstops
  678. *
  679. * - Prevent moves outside the set machine bounds.
  680. * - Individual axes can be disabled, if desired.
  681. * - X and Y only apply to Cartesian robots.
  682. * - Use 'M211' to set software endstops on/off or report current state
  683. */
  684. // Min software endstops constrain movement within minimum coordinate bounds
  685. #define MIN_SOFTWARE_ENDSTOPS
  686. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  687. #define MIN_SOFTWARE_ENDSTOP_X
  688. #define MIN_SOFTWARE_ENDSTOP_Y
  689. #define MIN_SOFTWARE_ENDSTOP_Z
  690. #endif
  691. // Max software endstops constrain movement within maximum coordinate bounds
  692. #define MAX_SOFTWARE_ENDSTOPS
  693. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  694. #define MAX_SOFTWARE_ENDSTOP_X
  695. #define MAX_SOFTWARE_ENDSTOP_Y
  696. #define MAX_SOFTWARE_ENDSTOP_Z
  697. #endif
  698. /**
  699. * Filament Runout Sensor
  700. * A mechanical or opto endstop is used to check for the presence of filament.
  701. *
  702. * RAMPS-based boards use SERVO3_PIN.
  703. * For other boards you may need to define FIL_RUNOUT_PIN.
  704. * By default the firmware assumes HIGH = has filament, LOW = ran out
  705. */
  706. //#define FILAMENT_RUNOUT_SENSOR
  707. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  708. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  709. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  710. #define FILAMENT_RUNOUT_SCRIPT "M600"
  711. #endif
  712. //===========================================================================
  713. //=============================== Bed Leveling ==============================
  714. //===========================================================================
  715. // @section bedlevel
  716. /**
  717. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  718. * and behavior of G29 will change depending on your selection.
  719. *
  720. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  721. *
  722. * - AUTO_BED_LEVELING_3POINT
  723. * Probe 3 arbitrary points on the bed (that aren't collinear)
  724. * You specify the XY coordinates of all 3 points.
  725. * The result is a single tilted plane. Best for a flat bed.
  726. *
  727. * - AUTO_BED_LEVELING_LINEAR
  728. * Probe several points in a grid.
  729. * You specify the rectangle and the density of sample points.
  730. * The result is a single tilted plane. Best for a flat bed.
  731. *
  732. * - AUTO_BED_LEVELING_BILINEAR
  733. * Probe several points in a grid.
  734. * You specify the rectangle and the density of sample points.
  735. * The result is a mesh, best for large or uneven beds.
  736. *
  737. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  738. * A comprehensive bed leveling system combining the features and benefits
  739. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  740. * Validation and Mesh Editing systems.
  741. *
  742. * - MESH_BED_LEVELING
  743. * Probe a grid manually
  744. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  745. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  746. * leveling in steps so you can manually adjust the Z height at each grid-point.
  747. * With an LCD controller the process is guided step-by-step.
  748. */
  749. //#define AUTO_BED_LEVELING_3POINT
  750. //#define AUTO_BED_LEVELING_LINEAR
  751. //#define AUTO_BED_LEVELING_BILINEAR
  752. //#define AUTO_BED_LEVELING_UBL
  753. //#define MESH_BED_LEVELING
  754. /**
  755. * Enable detailed logging of G28, G29, M48, etc.
  756. * Turn on with the command 'M111 S32'.
  757. * NOTE: Requires a lot of PROGMEM!
  758. */
  759. //#define DEBUG_LEVELING_FEATURE
  760. //#define ENABLE_MESH_EDIT_GFX_OVERLAY // enable a graphics overly while editing the mesh from auto-level
  761. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  762. // Gradually reduce leveling correction until a set height is reached,
  763. // at which point movement will be level to the machine's XY plane.
  764. // The height can be set with M420 Z<height>
  765. #define ENABLE_LEVELING_FADE_HEIGHT
  766. #endif
  767. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  768. // Set the number of grid points per dimension.
  769. #define GRID_MAX_POINTS_X 3
  770. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  771. // Set the boundaries for probing (where the probe can reach).
  772. #define LEFT_PROBE_BED_POSITION 15
  773. #define RIGHT_PROBE_BED_POSITION 170
  774. #define FRONT_PROBE_BED_POSITION 20
  775. #define BACK_PROBE_BED_POSITION 170
  776. // The Z probe minimum outer margin (to validate G29 parameters).
  777. #define MIN_PROBE_EDGE 10
  778. // Probe along the Y axis, advancing X after each column
  779. //#define PROBE_Y_FIRST
  780. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  781. // Beyond the probed grid, continue the implied tilt?
  782. // Default is to maintain the height of the nearest edge.
  783. //#define EXTRAPOLATE_BEYOND_GRID
  784. //
  785. // Experimental Subdivision of the grid by Catmull-Rom method.
  786. // Synthesizes intermediate points to produce a more detailed mesh.
  787. //
  788. //#define ABL_BILINEAR_SUBDIVISION
  789. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  790. // Number of subdivisions between probe points
  791. #define BILINEAR_SUBDIVISIONS 3
  792. #endif
  793. #endif
  794. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  795. // 3 arbitrary points to probe.
  796. // A simple cross-product is used to estimate the plane of the bed.
  797. #define ABL_PROBE_PT_1_X 15
  798. #define ABL_PROBE_PT_1_Y 180
  799. #define ABL_PROBE_PT_2_X 15
  800. #define ABL_PROBE_PT_2_Y 20
  801. #define ABL_PROBE_PT_3_X 170
  802. #define ABL_PROBE_PT_3_Y 20
  803. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  804. //===========================================================================
  805. //========================= Unified Bed Leveling ============================
  806. //===========================================================================
  807. #define MESH_INSET 1 // Mesh inset margin on print area
  808. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  809. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  810. #define UBL_PROBE_PT_1_X 39 // Probing points for 3-Point leveling of the mesh
  811. #define UBL_PROBE_PT_1_Y 180
  812. #define UBL_PROBE_PT_2_X 39
  813. #define UBL_PROBE_PT_2_Y 20
  814. #define UBL_PROBE_PT_3_X 180
  815. #define UBL_PROBE_PT_3_Y 20
  816. //#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
  817. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  818. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  819. #elif ENABLED(MESH_BED_LEVELING)
  820. //===========================================================================
  821. //=================================== Mesh ==================================
  822. //===========================================================================
  823. #define MESH_INSET 10 // Mesh inset margin on print area
  824. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  825. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  826. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  827. #endif // BED_LEVELING
  828. /**
  829. * Use the LCD controller for bed leveling
  830. * Requires MESH_BED_LEVELING or PROBE_MANUALLY
  831. */
  832. //#define LCD_BED_LEVELING
  833. #if ENABLED(LCD_BED_LEVELING)
  834. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  835. #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  836. #endif
  837. // Add a menu item to move between bed corners for manual bed adjustment
  838. //#define LEVEL_BED_CORNERS
  839. /**
  840. * Commands to execute at the end of G29 probing.
  841. * Useful to retract or move the Z probe out of the way.
  842. */
  843. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  844. // @section homing
  845. // The center of the bed is at (X=0, Y=0)
  846. //#define BED_CENTER_AT_0_0
  847. // Manually set the home position. Leave these undefined for automatic settings.
  848. // For DELTA this is the top-center of the Cartesian print volume.
  849. //#define MANUAL_X_HOME_POS 0
  850. //#define MANUAL_Y_HOME_POS 0
  851. //#define MANUAL_Z_HOME_POS 0
  852. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  853. //
  854. // With this feature enabled:
  855. //
  856. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  857. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  858. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  859. // - Prevent Z homing when the Z probe is outside bed area.
  860. //
  861. //#define Z_SAFE_HOMING
  862. #if ENABLED(Z_SAFE_HOMING)
  863. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  864. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  865. #endif
  866. // Homing speeds (mm/m)
  867. #define HOMING_FEEDRATE_XY (50*60)
  868. #define HOMING_FEEDRATE_Z (4*60)
  869. //=============================================================================
  870. //============================= Additional Features ===========================
  871. //=============================================================================
  872. // @section extras
  873. //
  874. // EEPROM
  875. //
  876. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  877. // M500 - stores parameters in EEPROM
  878. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  879. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  880. //
  881. //#define EEPROM_SETTINGS // Enable for M500 and M501 commands
  882. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  883. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  884. //
  885. // Host Keepalive
  886. //
  887. // When enabled Marlin will send a busy status message to the host
  888. // every couple of seconds when it can't accept commands.
  889. //
  890. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  891. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  892. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  893. //
  894. // M100 Free Memory Watcher
  895. //
  896. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  897. //
  898. // G20/G21 Inch mode support
  899. //
  900. //#define INCH_MODE_SUPPORT
  901. //
  902. // M149 Set temperature units support
  903. //
  904. //#define TEMPERATURE_UNITS_SUPPORT
  905. // @section temperature
  906. // Preheat Constants
  907. #define PREHEAT_1_TEMP_HOTEND 180
  908. #define PREHEAT_1_TEMP_BED 70
  909. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  910. #define PREHEAT_2_TEMP_HOTEND 240
  911. #define PREHEAT_2_TEMP_BED 110
  912. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  913. /**
  914. * Nozzle Park -- EXPERIMENTAL
  915. *
  916. * Park the nozzle at the given XYZ position on idle or G27.
  917. *
  918. * The "P" parameter controls the action applied to the Z axis:
  919. *
  920. * P0 (Default) If Z is below park Z raise the nozzle.
  921. * P1 Raise the nozzle always to Z-park height.
  922. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  923. */
  924. //#define NOZZLE_PARK_FEATURE
  925. #if ENABLED(NOZZLE_PARK_FEATURE)
  926. // Specify a park position as { X, Y, Z }
  927. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  928. #endif
  929. /**
  930. * Clean Nozzle Feature -- EXPERIMENTAL
  931. *
  932. * Adds the G12 command to perform a nozzle cleaning process.
  933. *
  934. * Parameters:
  935. * P Pattern
  936. * S Strokes / Repetitions
  937. * T Triangles (P1 only)
  938. *
  939. * Patterns:
  940. * P0 Straight line (default). This process requires a sponge type material
  941. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  942. * between the start / end points.
  943. *
  944. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  945. * number of zig-zag triangles to do. "S" defines the number of strokes.
  946. * Zig-zags are done in whichever is the narrower dimension.
  947. * For example, "G12 P1 S1 T3" will execute:
  948. *
  949. * --
  950. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  951. * | | / \ / \ / \ |
  952. * A | | / \ / \ / \ |
  953. * | | / \ / \ / \ |
  954. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  955. * -- +--------------------------------+
  956. * |________|_________|_________|
  957. * T1 T2 T3
  958. *
  959. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  960. * "R" specifies the radius. "S" specifies the stroke count.
  961. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  962. *
  963. * Caveats: The ending Z should be the same as starting Z.
  964. * Attention: EXPERIMENTAL. G-code arguments may change.
  965. *
  966. */
  967. //#define NOZZLE_CLEAN_FEATURE
  968. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  969. // Default number of pattern repetitions
  970. #define NOZZLE_CLEAN_STROKES 12
  971. // Default number of triangles
  972. #define NOZZLE_CLEAN_TRIANGLES 3
  973. // Specify positions as { X, Y, Z }
  974. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  975. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  976. // Circular pattern radius
  977. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  978. // Circular pattern circle fragments number
  979. #define NOZZLE_CLEAN_CIRCLE_FN 10
  980. // Middle point of circle
  981. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  982. // Moves the nozzle to the initial position
  983. #define NOZZLE_CLEAN_GOBACK
  984. #endif
  985. /**
  986. * Print Job Timer
  987. *
  988. * Automatically start and stop the print job timer on M104/M109/M190.
  989. *
  990. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  991. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  992. * M190 (bed, wait) - high temp = start timer, low temp = none
  993. *
  994. * The timer can also be controlled with the following commands:
  995. *
  996. * M75 - Start the print job timer
  997. * M76 - Pause the print job timer
  998. * M77 - Stop the print job timer
  999. */
  1000. #define PRINTJOB_TIMER_AUTOSTART
  1001. /**
  1002. * Print Counter
  1003. *
  1004. * Track statistical data such as:
  1005. *
  1006. * - Total print jobs
  1007. * - Total successful print jobs
  1008. * - Total failed print jobs
  1009. * - Total time printing
  1010. *
  1011. * View the current statistics with M78.
  1012. */
  1013. //#define PRINTCOUNTER
  1014. //=============================================================================
  1015. //============================= LCD and SD support ============================
  1016. //=============================================================================
  1017. // @section lcd
  1018. /**
  1019. * LCD LANGUAGE
  1020. *
  1021. * Select the language to display on the LCD. These languages are available:
  1022. *
  1023. * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
  1024. * hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
  1025. * tr, uk, zh_CN, zh_TW, test
  1026. *
  1027. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
  1028. */
  1029. #define LCD_LANGUAGE en
  1030. /**
  1031. * LCD Character Set
  1032. *
  1033. * Note: This option is NOT applicable to Graphical Displays.
  1034. *
  1035. * All character-based LCDs provide ASCII plus one of these
  1036. * language extensions:
  1037. *
  1038. * - JAPANESE ... the most common
  1039. * - WESTERN ... with more accented characters
  1040. * - CYRILLIC ... for the Russian language
  1041. *
  1042. * To determine the language extension installed on your controller:
  1043. *
  1044. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1045. * - Click the controller to view the LCD menu
  1046. * - The LCD will display Japanese, Western, or Cyrillic text
  1047. *
  1048. * See http://marlinfw.org/docs/development/lcd_language.html
  1049. *
  1050. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1051. */
  1052. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1053. /**
  1054. * LCD TYPE
  1055. *
  1056. * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1057. * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
  1058. * (These options will be enabled automatically for most displays.)
  1059. *
  1060. * IMPORTANT: The U8glib library is required for Full Graphic Display!
  1061. * https://github.com/olikraus/U8glib_Arduino
  1062. */
  1063. //#define ULTRA_LCD // Character based
  1064. //#define DOGLCD // Full graphics display
  1065. /**
  1066. * SD CARD
  1067. *
  1068. * SD Card support is disabled by default. If your controller has an SD slot,
  1069. * you must uncomment the following option or it won't work.
  1070. *
  1071. */
  1072. //#define SDSUPPORT
  1073. /**
  1074. * SD CARD: SPI SPEED
  1075. *
  1076. * Enable one of the following items for a slower SPI transfer speed.
  1077. * This may be required to resolve "volume init" errors.
  1078. */
  1079. //#define SPI_SPEED SPI_HALF_SPEED
  1080. //#define SPI_SPEED SPI_QUARTER_SPEED
  1081. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1082. /**
  1083. * SD CARD: ENABLE CRC
  1084. *
  1085. * Use CRC checks and retries on the SD communication.
  1086. */
  1087. //#define SD_CHECK_AND_RETRY
  1088. //
  1089. // ENCODER SETTINGS
  1090. //
  1091. // This option overrides the default number of encoder pulses needed to
  1092. // produce one step. Should be increased for high-resolution encoders.
  1093. //
  1094. //#define ENCODER_PULSES_PER_STEP 1
  1095. //
  1096. // Use this option to override the number of step signals required to
  1097. // move between next/prev menu items.
  1098. //
  1099. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  1100. /**
  1101. * Encoder Direction Options
  1102. *
  1103. * Test your encoder's behavior first with both options disabled.
  1104. *
  1105. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1106. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1107. * Reversed Value Editing only? Enable BOTH options.
  1108. */
  1109. //
  1110. // This option reverses the encoder direction everywhere.
  1111. //
  1112. // Set this option if CLOCKWISE causes values to DECREASE
  1113. //
  1114. //#define REVERSE_ENCODER_DIRECTION
  1115. //
  1116. // This option reverses the encoder direction for navigating LCD menus.
  1117. //
  1118. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1119. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1120. //
  1121. //#define REVERSE_MENU_DIRECTION
  1122. //
  1123. // Individual Axis Homing
  1124. //
  1125. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1126. //
  1127. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1128. //
  1129. // SPEAKER/BUZZER
  1130. //
  1131. // If you have a speaker that can produce tones, enable it here.
  1132. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1133. //
  1134. //#define SPEAKER
  1135. //
  1136. // The duration and frequency for the UI feedback sound.
  1137. // Set these to 0 to disable audio feedback in the LCD menus.
  1138. //
  1139. // Note: Test audio output with the G-Code:
  1140. // M300 S<frequency Hz> P<duration ms>
  1141. //
  1142. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1143. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1144. //
  1145. // CONTROLLER TYPE: Standard
  1146. //
  1147. // Marlin supports a wide variety of controllers.
  1148. // Enable one of the following options to specify your controller.
  1149. //
  1150. //
  1151. // ULTIMAKER Controller.
  1152. //
  1153. //#define ULTIMAKERCONTROLLER
  1154. //
  1155. // ULTIPANEL as seen on Thingiverse.
  1156. //
  1157. //#define ULTIPANEL
  1158. //
  1159. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1160. // http://reprap.org/wiki/PanelOne
  1161. //
  1162. //#define PANEL_ONE
  1163. //
  1164. // MaKr3d Makr-Panel with graphic controller and SD support.
  1165. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1166. //
  1167. //#define MAKRPANEL
  1168. //
  1169. // ReprapWorld Graphical LCD
  1170. // https://reprapworld.com/?products_details&products_id/1218
  1171. //
  1172. //#define REPRAPWORLD_GRAPHICAL_LCD
  1173. //
  1174. // Activate one of these if you have a Panucatt Devices
  1175. // Viki 2.0 or mini Viki with Graphic LCD
  1176. // http://panucatt.com
  1177. //
  1178. //#define VIKI2
  1179. //#define miniVIKI
  1180. //
  1181. // Adafruit ST7565 Full Graphic Controller.
  1182. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1183. //
  1184. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1185. //
  1186. // RepRapDiscount Smart Controller.
  1187. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1188. //
  1189. // Note: Usually sold with a white PCB.
  1190. //
  1191. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1192. //
  1193. // GADGETS3D G3D LCD/SD Controller
  1194. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1195. //
  1196. // Note: Usually sold with a blue PCB.
  1197. //
  1198. //#define G3D_PANEL
  1199. //
  1200. // RepRapDiscount FULL GRAPHIC Smart Controller
  1201. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1202. //
  1203. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1204. //
  1205. // MakerLab Mini Panel with graphic
  1206. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1207. //
  1208. //#define MINIPANEL
  1209. //
  1210. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1211. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1212. //
  1213. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1214. // is pressed, a value of 10.0 means 10mm per click.
  1215. //
  1216. //#define REPRAPWORLD_KEYPAD
  1217. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1218. //
  1219. // RigidBot Panel V1.0
  1220. // http://www.inventapart.com/
  1221. //
  1222. //#define RIGIDBOT_PANEL
  1223. //
  1224. // BQ LCD Smart Controller shipped by
  1225. // default with the BQ Hephestos 2 and Witbox 2.
  1226. //
  1227. //#define BQ_LCD_SMART_CONTROLLER
  1228. //
  1229. // Cartesio UI
  1230. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1231. //
  1232. //#define CARTESIO_UI
  1233. //
  1234. // ANET_10 Controller supported displays.
  1235. //
  1236. //#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1237. // This LCD is known to be susceptible to electrical interference
  1238. // which scrambles the display. Pressing any button clears it up.
  1239. //#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1240. // A clone of the RepRapDiscount full graphics display but with
  1241. // different pins/wiring (see pins_ANET_10.h).
  1242. //
  1243. // LCD for Melzi Card with Graphical LCD
  1244. //
  1245. //#define LCD_FOR_MELZI
  1246. //
  1247. // CONTROLLER TYPE: I2C
  1248. //
  1249. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1250. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1251. //
  1252. //
  1253. // Elefu RA Board Control Panel
  1254. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1255. //
  1256. //#define RA_CONTROL_PANEL
  1257. //
  1258. // Sainsmart YW Robot (LCM1602) LCD Display
  1259. //
  1260. // Note: This controller requires F.Malpartida's LiquidCrystal_I2C library
  1261. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1262. //
  1263. //#define LCD_I2C_SAINSMART_YWROBOT
  1264. //
  1265. // Generic LCM1602 LCD adapter
  1266. //
  1267. //#define LCM1602
  1268. //
  1269. // PANELOLU2 LCD with status LEDs,
  1270. // separate encoder and click inputs.
  1271. //
  1272. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1273. // For more info: https://github.com/lincomatic/LiquidTWI2
  1274. //
  1275. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1276. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1277. //
  1278. //#define LCD_I2C_PANELOLU2
  1279. //
  1280. // Panucatt VIKI LCD with status LEDs,
  1281. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1282. //
  1283. //#define LCD_I2C_VIKI
  1284. //
  1285. // SSD1306 OLED full graphics generic display
  1286. //
  1287. //#define U8GLIB_SSD1306
  1288. //
  1289. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1290. //
  1291. //#define SAV_3DGLCD
  1292. #if ENABLED(SAV_3DGLCD)
  1293. //#define U8GLIB_SSD1306
  1294. #define U8GLIB_SH1106
  1295. #endif
  1296. //
  1297. // CONTROLLER TYPE: Shift register panels
  1298. //
  1299. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1300. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1301. //
  1302. //#define SAV_3DLCD
  1303. //
  1304. // TinyBoy2 128x64 OLED / Encoder Panel
  1305. //
  1306. //#define OLED_PANEL_TINYBOY2
  1307. //
  1308. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1309. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1310. //
  1311. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1312. //
  1313. // MKS MINI12864 with graphic controller and SD support
  1314. // http://reprap.org/wiki/MKS_MINI_12864
  1315. //
  1316. //#define MKS_MINI_12864
  1317. //
  1318. // Factory display for Creality CR-10
  1319. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1320. //
  1321. // This is RAMPS-compatible using a single 10-pin connector.
  1322. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1323. //
  1324. //#define CR10_STOCKDISPLAY
  1325. //
  1326. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1327. // http://reprap.org/wiki/MKS_12864OLED
  1328. //
  1329. // Tiny, but very sharp OLED display
  1330. //
  1331. //#define MKS_12864OLED
  1332. //
  1333. // AZSMZ 12864 LCD with SD
  1334. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1335. //
  1336. //#define AZSMZ_12864
  1337. // Silvergate GLCD controller
  1338. // http://github.com/android444/Silvergate
  1339. //
  1340. //#define SILVER_GATE_GLCD_CONTROLLER
  1341. //=============================================================================
  1342. //=============================== Extra Features ==============================
  1343. //=============================================================================
  1344. // @section extras
  1345. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1346. //#define FAST_PWM_FAN
  1347. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1348. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1349. // is too low, you should also increment SOFT_PWM_SCALE.
  1350. //#define FAN_SOFT_PWM
  1351. // Incrementing this by 1 will double the software PWM frequency,
  1352. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1353. // However, control resolution will be halved for each increment;
  1354. // at zero value, there are 128 effective control positions.
  1355. #define SOFT_PWM_SCALE 0
  1356. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1357. // be used to mitigate the associated resolution loss. If enabled,
  1358. // some of the PWM cycles are stretched so on average the desired
  1359. // duty cycle is attained.
  1360. //#define SOFT_PWM_DITHER
  1361. // Temperature status LEDs that display the hotend and bed temperature.
  1362. // If all hotends, bed temperature, and target temperature are under 54C
  1363. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1364. //#define TEMP_STAT_LEDS
  1365. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1366. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1367. //#define PHOTOGRAPH_PIN 23
  1368. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1369. //#define SF_ARC_FIX
  1370. // Support for the BariCUDA Paste Extruder
  1371. //#define BARICUDA
  1372. // Support for BlinkM/CyzRgb
  1373. //#define BLINKM
  1374. // Support for PCA9632 PWM LED driver
  1375. //#define PCA9632
  1376. /**
  1377. * RGB LED / LED Strip Control
  1378. *
  1379. * Enable support for an RGB LED connected to 5V digital pins, or
  1380. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1381. *
  1382. * Adds the M150 command to set the LED (or LED strip) color.
  1383. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1384. * luminance values can be set from 0 to 255.
  1385. * For Neopixel LED an overall brightness parameter is also available.
  1386. *
  1387. * *** CAUTION ***
  1388. * LED Strips require a MOFSET Chip between PWM lines and LEDs,
  1389. * as the Arduino cannot handle the current the LEDs will require.
  1390. * Failure to follow this precaution can destroy your Arduino!
  1391. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1392. * more current than the Arduino 5V linear regulator can produce.
  1393. * *** CAUTION ***
  1394. *
  1395. * LED Type. Enable only one of the following two options.
  1396. *
  1397. */
  1398. //#define RGB_LED
  1399. //#define RGBW_LED
  1400. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1401. #define RGB_LED_R_PIN 34
  1402. #define RGB_LED_G_PIN 43
  1403. #define RGB_LED_B_PIN 35
  1404. #define RGB_LED_W_PIN -1
  1405. #endif
  1406. // Support for Adafruit Neopixel LED driver
  1407. //#define NEOPIXEL_LED
  1408. #if ENABLED(NEOPIXEL_LED)
  1409. #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1410. #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  1411. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
  1412. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1413. #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
  1414. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1415. #endif
  1416. /**
  1417. * Printer Event LEDs
  1418. *
  1419. * During printing, the LEDs will reflect the printer status:
  1420. *
  1421. * - Gradually change from blue to violet as the heated bed gets to target temp
  1422. * - Gradually change from violet to red as the hotend gets to temperature
  1423. * - Change to white to illuminate work surface
  1424. * - Change to green once print has finished
  1425. * - Turn off after the print has finished and the user has pushed a button
  1426. */
  1427. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
  1428. #define PRINTER_EVENT_LEDS
  1429. #endif
  1430. /**
  1431. * R/C SERVO support
  1432. * Sponsored by TrinityLabs, Reworked by codexmas
  1433. */
  1434. /**
  1435. * Number of servos
  1436. *
  1437. * For some servo-related options NUM_SERVOS will be set automatically.
  1438. * Set this manually if there are extra servos needing manual control.
  1439. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1440. */
  1441. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1442. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1443. // 300ms is a good value but you can try less delay.
  1444. // If the servo can't reach the requested position, increase it.
  1445. #define SERVO_DELAY { 300 }
  1446. // Servo deactivation
  1447. //
  1448. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1449. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1450. /**
  1451. * Filament Width Sensor
  1452. *
  1453. * Measures the filament width in real-time and adjusts
  1454. * flow rate to compensate for any irregularities.
  1455. *
  1456. * Also allows the measured filament diameter to set the
  1457. * extrusion rate, so the slicer only has to specify the
  1458. * volume.
  1459. *
  1460. * Only a single extruder is supported at this time.
  1461. *
  1462. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  1463. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  1464. * 301 RAMBO : Analog input 3
  1465. *
  1466. * Note: May require analog pins to be defined for other boards.
  1467. */
  1468. //#define FILAMENT_WIDTH_SENSOR
  1469. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
  1470. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  1471. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
  1472. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  1473. #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
  1474. #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
  1475. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  1476. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  1477. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  1478. //#define FILAMENT_LCD_DISPLAY
  1479. #endif
  1480. #endif // CONFIGURATION_H