My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Du kan inte välja fler än 25 ämnen Ämnen måste starta med en bokstav eller siffra, kan innehålla bindestreck ('-') och vara max 35 tecken långa.

Configuration.h 109KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497149814991500150115021503150415051506150715081509151015111512151315141515151615171518151915201521152215231524152515261527152815291530153115321533153415351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563156415651566156715681569157015711572157315741575157615771578157915801581158215831584158515861587158815891590159115921593159415951596159715981599160016011602160316041605160616071608160916101611161216131614161516161617161816191620162116221623162416251626162716281629163016311632163316341635163616371638163916401641164216431644164516461647164816491650165116521653165416551656165716581659166016611662166316641665166616671668166916701671167216731674167516761677167816791680168116821683168416851686168716881689169016911692169316941695169616971698169917001701170217031704170517061707170817091710171117121713171417151716171717181719172017211722172317241725172617271728172917301731173217331734173517361737173817391740174117421743174417451746174717481749175017511752175317541755175617571758175917601761176217631764176517661767176817691770177117721773177417751776177717781779178017811782178317841785178617871788178917901791179217931794179517961797179817991800180118021803180418051806180718081809181018111812181318141815181618171818181918201821182218231824182518261827182818291830183118321833183418351836183718381839184018411842184318441845184618471848184918501851185218531854185518561857185818591860186118621863186418651866186718681869187018711872187318741875187618771878187918801881188218831884188518861887188818891890189118921893189418951896189718981899190019011902190319041905190619071908190919101911191219131914191519161917191819191920192119221923192419251926192719281929193019311932193319341935193619371938193919401941194219431944194519461947194819491950195119521953195419551956195719581959196019611962196319641965196619671968196919701971197219731974197519761977197819791980198119821983198419851986198719881989199019911992199319941995199619971998199920002001200220032004200520062007200820092010201120122013201420152016201720182019202020212022202320242025202620272028202920302031203220332034203520362037203820392040204120422043204420452046204720482049205020512052205320542055205620572058205920602061206220632064206520662067206820692070207120722073207420752076207720782079208020812082208320842085208620872088208920902091209220932094209520962097209820992100210121022103210421052106210721082109211021112112211321142115211621172118211921202121212221232124212521262127212821292130213121322133213421352136213721382139214021412142214321442145214621472148214921502151215221532154215521562157215821592160216121622163216421652166216721682169217021712172217321742175217621772178217921802181218221832184218521862187218821892190219121922193219421952196219721982199220022012202220322042205220622072208220922102211221222132214221522162217221822192220222122222223222422252226222722282229223022312232223322342235223622372238223922402241224222432244224522462247224822492250225122522253225422552256225722582259226022612262226322642265226622672268226922702271227222732274227522762277227822792280228122822283228422852286228722882289229022912292229322942295229622972298229923002301230223032304230523062307230823092310231123122313231423152316231723182319232023212322232323242325232623272328232923302331233223332334233523362337233823392340234123422343234423452346234723482349235023512352235323542355235623572358235923602361236223632364236523662367236823692370237123722373237423752376237723782379238023812382238323842385238623872388238923902391239223932394239523962397239823992400240124022403240424052406240724082409241024112412241324142415241624172418241924202421242224232424242524262427242824292430243124322433243424352436243724382439244024412442244324442445244624472448244924502451245224532454245524562457245824592460246124622463246424652466246724682469247024712472247324742475247624772478247924802481248224832484248524862487248824892490249124922493249424952496249724982499250025012502250325042505250625072508250925102511251225132514251525162517251825192520252125222523252425252526252725282529253025312532253325342535253625372538253925402541254225432544254525462547254825492550255125522553255425552556255725582559256025612562256325642565256625672568256925702571257225732574257525762577257825792580258125822583258425852586258725882589259025912592259325942595259625972598259926002601260226032604260526062607260826092610261126122613261426152616261726182619262026212622262326242625262626272628262926302631263226332634263526362637263826392640264126422643264426452646264726482649265026512652265326542655265626572658265926602661266226632664266526662667266826692670267126722673267426752676267726782679268026812682268326842685268626872688268926902691269226932694269526962697269826992700270127022703270427052706270727082709271027112712271327142715271627172718271927202721272227232724272527262727272827292730273127322733273427352736273727382739274027412742274327442745274627472748274927502751275227532754275527562757275827592760276127622763276427652766276727682769277027712772277327742775277627772778277927802781278227832784278527862787278827892790279127922793279427952796279727982799280028012802280328042805280628072808280928102811281228132814281528162817281828192820282128222823282428252826282728282829283028312832283328342835283628372838283928402841284228432844284528462847284828492850285128522853285428552856285728582859286028612862286328642865286628672868286928702871287228732874287528762877287828792880288128822883288428852886288728882889289028912892289328942895289628972898289929002901290229032904290529062907290829092910291129122913291429152916291729182919292029212922292329242925292629272928292929302931293229332934293529362937293829392940294129422943294429452946294729482949295029512952295329542955295629572958295929602961296229632964296529662967296829692970297129722973297429752976297729782979298029812982298329842985298629872988298929902991
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. */
  37. #define CONFIGURATION_H_VERSION 02000903
  38. //===========================================================================
  39. //============================= Getting Started =============================
  40. //===========================================================================
  41. /**
  42. * Here are some useful links to help get your machine configured and calibrated:
  43. *
  44. * Example Configs: https://github.com/MarlinFirmware/Configurations/branches/all
  45. *
  46. * Průša Calculator: https://blog.prusaprinters.org/calculator_3416/
  47. *
  48. * Calibration Guides: https://reprap.org/wiki/Calibration
  49. * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * https://youtu.be/wAL9d7FgInk
  52. *
  53. * Calibration Objects: https://www.thingiverse.com/thing:5573
  54. * https://www.thingiverse.com/thing:1278865
  55. */
  56. //===========================================================================
  57. //========================== DELTA / SCARA / TPARA ==========================
  58. //===========================================================================
  59. //
  60. // Download configurations from the link above and customize for your machine.
  61. // Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
  62. //
  63. //===========================================================================
  64. // @section info
  65. // Author info of this build printed to the host during boot and M115
  66. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  67. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  68. /**
  69. * *** VENDORS PLEASE READ ***
  70. *
  71. * Marlin allows you to add a custom boot image for Graphical LCDs.
  72. * With this option Marlin will first show your custom screen followed
  73. * by the standard Marlin logo with version number and web URL.
  74. *
  75. * We encourage you to take advantage of this new feature and we also
  76. * respectfully request that you retain the unmodified Marlin boot screen.
  77. */
  78. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  79. #define SHOW_BOOTSCREEN
  80. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  81. //#define SHOW_CUSTOM_BOOTSCREEN
  82. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  83. //#define CUSTOM_STATUS_SCREEN_IMAGE
  84. // @section machine
  85. // Choose the name from boards.h that matches your setup
  86. #ifndef MOTHERBOARD
  87. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  88. #endif
  89. /**
  90. * Select the serial port on the board to use for communication with the host.
  91. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  92. * Serial port -1 is the USB emulated serial port, if available.
  93. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  94. *
  95. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  96. */
  97. #define SERIAL_PORT 0
  98. /**
  99. * Serial Port Baud Rate
  100. * This is the default communication speed for all serial ports.
  101. * Set the baud rate defaults for additional serial ports below.
  102. *
  103. * 250000 works in most cases, but you might try a lower speed if
  104. * you commonly experience drop-outs during host printing.
  105. * You may try up to 1000000 to speed up SD file transfer.
  106. *
  107. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  108. */
  109. #define BAUDRATE 250000
  110. //#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate
  111. /**
  112. * Select a secondary serial port on the board to use for communication with the host.
  113. * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  114. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  115. */
  116. //#define SERIAL_PORT_2 -1
  117. //#define BAUDRATE_2 250000 // Enable to override BAUDRATE
  118. /**
  119. * Select a third serial port on the board to use for communication with the host.
  120. * Currently only supported for AVR, DUE, LPC1768/9 and STM32/STM32F1
  121. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  122. */
  123. //#define SERIAL_PORT_3 1
  124. //#define BAUDRATE_3 250000 // Enable to override BAUDRATE
  125. // Enable the Bluetooth serial interface on AT90USB devices
  126. //#define BLUETOOTH
  127. // Name displayed in the LCD "Ready" message and Info menu
  128. //#define CUSTOM_MACHINE_NAME "3D Printer"
  129. // Printer's unique ID, used by some programs to differentiate between machines.
  130. // Choose your own or use a service like https://www.uuidgenerator.net/version4
  131. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  132. /**
  133. * Define the number of coordinated linear axes.
  134. * See https://github.com/DerAndere1/Marlin/wiki
  135. * Each linear axis gets its own stepper control and endstop:
  136. *
  137. * Steppers: *_STEP_PIN, *_ENABLE_PIN, *_DIR_PIN, *_ENABLE_ON
  138. * Endstops: *_STOP_PIN, USE_*MIN_PLUG, USE_*MAX_PLUG
  139. * Axes: *_MIN_POS, *_MAX_POS, INVERT_*_DIR
  140. * Planner: DEFAULT_AXIS_STEPS_PER_UNIT, DEFAULT_MAX_FEEDRATE
  141. * DEFAULT_MAX_ACCELERATION, AXIS_RELATIVE_MODES,
  142. * MICROSTEP_MODES, MANUAL_FEEDRATE
  143. *
  144. * :[3, 4, 5, 6]
  145. */
  146. //#define LINEAR_AXES 3
  147. /**
  148. * Axis codes for additional axes:
  149. * This defines the axis code that is used in G-code commands to
  150. * reference a specific axis.
  151. * 'A' for rotational axis parallel to X
  152. * 'B' for rotational axis parallel to Y
  153. * 'C' for rotational axis parallel to Z
  154. * 'U' for secondary linear axis parallel to X
  155. * 'V' for secondary linear axis parallel to Y
  156. * 'W' for secondary linear axis parallel to Z
  157. * Regardless of the settings, firmware-internal axis IDs are
  158. * I (AXIS4), J (AXIS5), K (AXIS6).
  159. */
  160. #if LINEAR_AXES >= 4
  161. #define AXIS4_NAME 'A' // :['A', 'B', 'C', 'U', 'V', 'W']
  162. #endif
  163. #if LINEAR_AXES >= 5
  164. #define AXIS5_NAME 'B' // :['A', 'B', 'C', 'U', 'V', 'W']
  165. #endif
  166. #if LINEAR_AXES >= 6
  167. #define AXIS6_NAME 'C' // :['A', 'B', 'C', 'U', 'V', 'W']
  168. #endif
  169. // @section extruder
  170. // This defines the number of extruders
  171. // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
  172. #define EXTRUDERS 1
  173. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  174. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  175. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  176. //#define SINGLENOZZLE
  177. // Save and restore temperature and fan speed on tool-change.
  178. // Set standby for the unselected tool with M104/106/109 T...
  179. #if ENABLED(SINGLENOZZLE)
  180. //#define SINGLENOZZLE_STANDBY_TEMP
  181. //#define SINGLENOZZLE_STANDBY_FAN
  182. #endif
  183. /**
  184. * Multi-Material Unit
  185. * Set to one of these predefined models:
  186. *
  187. * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version)
  188. * PRUSA_MMU2 : Průša MMU2
  189. * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
  190. * EXTENDABLE_EMU_MMU2 : MMU with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  191. * EXTENDABLE_EMU_MMU2S : MMUS with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  192. *
  193. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  194. * See additional options in Configuration_adv.h.
  195. */
  196. //#define MMU_MODEL PRUSA_MMU2
  197. // A dual extruder that uses a single stepper motor
  198. //#define SWITCHING_EXTRUDER
  199. #if ENABLED(SWITCHING_EXTRUDER)
  200. #define SWITCHING_EXTRUDER_SERVO_NR 0
  201. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  202. #if EXTRUDERS > 3
  203. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  204. #endif
  205. #endif
  206. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  207. //#define SWITCHING_NOZZLE
  208. #if ENABLED(SWITCHING_NOZZLE)
  209. #define SWITCHING_NOZZLE_SERVO_NR 0
  210. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  211. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  212. #endif
  213. /**
  214. * Two separate X-carriages with extruders that connect to a moving part
  215. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  216. */
  217. //#define PARKING_EXTRUDER
  218. /**
  219. * Two separate X-carriages with extruders that connect to a moving part
  220. * via a magnetic docking mechanism using movements and no solenoid
  221. *
  222. * project : https://www.thingiverse.com/thing:3080893
  223. * movements : https://youtu.be/0xCEiG9VS3k
  224. * https://youtu.be/Bqbcs0CU2FE
  225. */
  226. //#define MAGNETIC_PARKING_EXTRUDER
  227. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  228. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  229. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  230. #if ENABLED(PARKING_EXTRUDER)
  231. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  232. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  233. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  234. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  235. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  236. #define MPE_FAST_SPEED 9000 // (mm/min) Speed for travel before last distance point
  237. #define MPE_SLOW_SPEED 4500 // (mm/min) Speed for last distance travel to park and couple
  238. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  239. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  240. #endif
  241. #endif
  242. /**
  243. * Switching Toolhead
  244. *
  245. * Support for swappable and dockable toolheads, such as
  246. * the E3D Tool Changer. Toolheads are locked with a servo.
  247. */
  248. //#define SWITCHING_TOOLHEAD
  249. /**
  250. * Magnetic Switching Toolhead
  251. *
  252. * Support swappable and dockable toolheads with a magnetic
  253. * docking mechanism using movement and no servo.
  254. */
  255. //#define MAGNETIC_SWITCHING_TOOLHEAD
  256. /**
  257. * Electromagnetic Switching Toolhead
  258. *
  259. * Parking for CoreXY / HBot kinematics.
  260. * Toolheads are parked at one edge and held with an electromagnet.
  261. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  262. */
  263. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  264. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  265. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  266. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  267. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  268. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  269. #if ENABLED(SWITCHING_TOOLHEAD)
  270. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  271. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  272. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  273. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  274. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  275. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  276. #if ENABLED(PRIME_BEFORE_REMOVE)
  277. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  278. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  279. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/min) Extruder prime feedrate
  280. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/min) Extruder retract feedrate
  281. #endif
  282. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  283. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  284. #endif
  285. #endif
  286. /**
  287. * "Mixing Extruder"
  288. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  289. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  290. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  291. * - This implementation supports up to two mixing extruders.
  292. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  293. */
  294. //#define MIXING_EXTRUDER
  295. #if ENABLED(MIXING_EXTRUDER)
  296. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  297. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  298. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  299. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  300. //#define MIXING_PRESETS // Assign 8 default V-tool presets for 2 or 3 MIXING_STEPPERS
  301. #if ENABLED(GRADIENT_MIX)
  302. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  303. #endif
  304. #endif
  305. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  306. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  307. // For the other hotends it is their distance from the extruder 0 hotend.
  308. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  309. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  310. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  311. // @section machine
  312. /**
  313. * Power Supply Control
  314. *
  315. * Enable and connect the power supply to the PS_ON_PIN.
  316. * Specify whether the power supply is active HIGH or active LOW.
  317. */
  318. //#define PSU_CONTROL
  319. //#define PSU_NAME "Power Supply"
  320. #if ENABLED(PSU_CONTROL)
  321. //#define MKS_PWC // Using the MKS PWC add-on
  322. //#define PS_OFF_CONFIRM // Confirm dialog when power off
  323. //#define PS_OFF_SOUND // Beep 1s when power off
  324. #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box
  325. //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
  326. //#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power
  327. //#define POWER_OFF_TIMER // Enable M81 D<seconds> to power off after a delay
  328. //#define POWER_OFF_WAIT_FOR_COOLDOWN // Enable M81 S to power off only after cooldown
  329. //#define PSU_POWERUP_GCODE "M355 S1" // G-code to run after power-on (e.g., case light on)
  330. //#define PSU_POWEROFF_GCODE "M355 S0" // G-code to run before power-off (e.g., case light off)
  331. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  332. #if ENABLED(AUTO_POWER_CONTROL)
  333. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  334. #define AUTO_POWER_E_FANS
  335. #define AUTO_POWER_CONTROLLERFAN
  336. #define AUTO_POWER_CHAMBER_FAN
  337. #define AUTO_POWER_COOLER_FAN
  338. #define POWER_TIMEOUT 30 // (s) Turn off power if the machine is idle for this duration
  339. //#define POWER_OFF_DELAY 60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
  340. #endif
  341. #if EITHER(AUTO_POWER_CONTROL, POWER_OFF_WAIT_FOR_COOLDOWN)
  342. //#define AUTO_POWER_E_TEMP 50 // (°C) PSU on if any extruder is over this temperature
  343. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) PSU on if the chamber is over this temperature
  344. //#define AUTO_POWER_COOLER_TEMP 26 // (°C) PSU on if the cooler is over this temperature
  345. #endif
  346. #endif
  347. //===========================================================================
  348. //============================= Thermal Settings ============================
  349. //===========================================================================
  350. // @section temperature
  351. /**
  352. * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  353. *
  354. * Temperature sensors available:
  355. *
  356. * SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
  357. * -------
  358. * -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
  359. * NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
  360. * -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
  361. * -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
  362. *
  363. * NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
  364. * Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
  365. * Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
  366. * Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
  367. *
  368. * Analog Themocouple Boards
  369. * -------
  370. * -4 : AD8495 with Thermocouple
  371. * -1 : AD595 with Thermocouple
  372. *
  373. * Analog Thermistors - 4.7kΩ pullup - Normal
  374. * -------
  375. * 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
  376. * 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
  377. * 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
  378. * 2 : 200kΩ ATC Semitec 204GT-2
  379. * 202 : 200kΩ Copymaster 3D
  380. * 3 : ???Ω Mendel-parts thermistor
  381. * 4 : 10kΩ Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
  382. * 5 : 100kΩ ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
  383. * 501 : 100kΩ Zonestar - Tronxy X3A
  384. * 502 : 100kΩ Zonestar - used by hot bed in Zonestar Průša P802M
  385. * 512 : 100kΩ RPW-Ultra hotend
  386. * 6 : 100kΩ EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
  387. * 7 : 100kΩ Honeywell 135-104LAG-J01
  388. * 71 : 100kΩ Honeywell 135-104LAF-J01
  389. * 8 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT
  390. * 9 : 100kΩ GE Sensing AL03006-58.2K-97-G1
  391. * 10 : 100kΩ RS PRO 198-961
  392. * 11 : 100kΩ Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
  393. * 12 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
  394. * 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
  395. * 15 : 100kΩ Calibrated for JGAurora A5 hotend
  396. * 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
  397. * 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
  398. * 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
  399. * 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
  400. * 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
  401. * 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
  402. * 66 : 4.7MΩ Dyze Design High Temperature Thermistor
  403. * 67 : 500kΩ SliceEngineering 450°C Thermistor
  404. * 70 : 100kΩ bq Hephestos 2
  405. * 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
  406. * 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
  407. *
  408. * Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
  409. * ------- (but gives greater accuracy and more stable PID)
  410. * 51 : 100kΩ EPCOS (1kΩ pullup)
  411. * 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
  412. * 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
  413. *
  414. * Analog Thermistors - 10kΩ pullup - Atypical
  415. * -------
  416. * 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
  417. *
  418. * Analog RTDs (Pt100/Pt1000)
  419. * -------
  420. * 110 : Pt100 with 1kΩ pullup (atypical)
  421. * 147 : Pt100 with 4.7kΩ pullup
  422. * 1010 : Pt1000 with 1kΩ pullup (atypical)
  423. * 1047 : Pt1000 with 4.7kΩ pullup (E3D)
  424. * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  425. * NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
  426. * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
  427. * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  428. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  429. *
  430. * Custom/Dummy/Other Thermal Sensors
  431. * ------
  432. * 0 : not used
  433. * 1000 : Custom - Specify parameters in Configuration_adv.h
  434. *
  435. * !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  436. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  437. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  438. *
  439. */
  440. #define TEMP_SENSOR_0 1
  441. #define TEMP_SENSOR_1 0
  442. #define TEMP_SENSOR_2 0
  443. #define TEMP_SENSOR_3 0
  444. #define TEMP_SENSOR_4 0
  445. #define TEMP_SENSOR_5 0
  446. #define TEMP_SENSOR_6 0
  447. #define TEMP_SENSOR_7 0
  448. #define TEMP_SENSOR_BED 0
  449. #define TEMP_SENSOR_PROBE 0
  450. #define TEMP_SENSOR_CHAMBER 0
  451. #define TEMP_SENSOR_COOLER 0
  452. #define TEMP_SENSOR_BOARD 0
  453. #define TEMP_SENSOR_REDUNDANT 0
  454. // Dummy thermistor constant temperature readings, for use with 998 and 999
  455. #define DUMMY_THERMISTOR_998_VALUE 25
  456. #define DUMMY_THERMISTOR_999_VALUE 100
  457. // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
  458. //#define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000)
  459. //#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for Adafruit PT100; 4300 for Adafruit PT1000
  460. //#define MAX31865_SENSOR_OHMS_1 100
  461. //#define MAX31865_CALIBRATION_OHMS_1 430
  462. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  463. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  464. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  465. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  466. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  467. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  468. #define TEMP_CHAMBER_RESIDENCY_TIME 10 // (seconds) Time to wait for chamber to "settle" in M191
  469. #define TEMP_CHAMBER_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  470. #define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  471. /**
  472. * Redundant Temperature Sensor (TEMP_SENSOR_REDUNDANT)
  473. *
  474. * Use a temp sensor as a redundant sensor for another reading. Select an unused temperature sensor, and another
  475. * sensor you'd like it to be redundant for. If the two thermistors differ by TEMP_SENSOR_REDUNDANT_MAX_DIFF (°C),
  476. * the print will be aborted. Whichever sensor is selected will have its normal functions disabled; i.e. selecting
  477. * the Bed sensor (-1) will disable bed heating/monitoring.
  478. *
  479. * For selecting source/target use: COOLER, PROBE, BOARD, CHAMBER, BED, E0, E1, E2, E3, E4, E5, E6, E7
  480. */
  481. #if TEMP_SENSOR_REDUNDANT
  482. #define TEMP_SENSOR_REDUNDANT_SOURCE E1 // The sensor that will provide the redundant reading.
  483. #define TEMP_SENSOR_REDUNDANT_TARGET E0 // The sensor that we are providing a redundant reading for.
  484. #define TEMP_SENSOR_REDUNDANT_MAX_DIFF 10 // (°C) Temperature difference that will trigger a print abort.
  485. #endif
  486. // Below this temperature the heater will be switched off
  487. // because it probably indicates a broken thermistor wire.
  488. #define HEATER_0_MINTEMP 5
  489. #define HEATER_1_MINTEMP 5
  490. #define HEATER_2_MINTEMP 5
  491. #define HEATER_3_MINTEMP 5
  492. #define HEATER_4_MINTEMP 5
  493. #define HEATER_5_MINTEMP 5
  494. #define HEATER_6_MINTEMP 5
  495. #define HEATER_7_MINTEMP 5
  496. #define BED_MINTEMP 5
  497. #define CHAMBER_MINTEMP 5
  498. // Above this temperature the heater will be switched off.
  499. // This can protect components from overheating, but NOT from shorts and failures.
  500. // (Use MINTEMP for thermistor short/failure protection.)
  501. #define HEATER_0_MAXTEMP 275
  502. #define HEATER_1_MAXTEMP 275
  503. #define HEATER_2_MAXTEMP 275
  504. #define HEATER_3_MAXTEMP 275
  505. #define HEATER_4_MAXTEMP 275
  506. #define HEATER_5_MAXTEMP 275
  507. #define HEATER_6_MAXTEMP 275
  508. #define HEATER_7_MAXTEMP 275
  509. #define BED_MAXTEMP 150
  510. #define CHAMBER_MAXTEMP 60
  511. /**
  512. * Thermal Overshoot
  513. * During heatup (and printing) the temperature can often "overshoot" the target by many degrees
  514. * (especially before PID tuning). Setting the target temperature too close to MAXTEMP guarantees
  515. * a MAXTEMP shutdown! Use these values to forbid temperatures being set too close to MAXTEMP.
  516. */
  517. #define HOTEND_OVERSHOOT 15 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
  518. #define BED_OVERSHOOT 10 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
  519. #define COOLER_OVERSHOOT 2 // (°C) Forbid temperatures closer than OVERSHOOT
  520. //===========================================================================
  521. //============================= PID Settings ================================
  522. //===========================================================================
  523. // PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning
  524. // Comment the following line to disable PID and enable bang-bang.
  525. #define PIDTEMP
  526. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  527. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  528. #define PID_K1 0.95 // Smoothing factor within any PID loop
  529. #if ENABLED(PIDTEMP)
  530. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  531. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  532. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  533. // Set/get with gcode: M301 E[extruder number, 0-2]
  534. #if ENABLED(PID_PARAMS_PER_HOTEND)
  535. // Specify up to one value per hotend here, according to your setup.
  536. // If there are fewer values, the last one applies to the remaining hotends.
  537. #define DEFAULT_Kp_LIST { 22.20, 22.20 }
  538. #define DEFAULT_Ki_LIST { 1.08, 1.08 }
  539. #define DEFAULT_Kd_LIST { 114.00, 114.00 }
  540. #else
  541. #define DEFAULT_Kp 22.20
  542. #define DEFAULT_Ki 1.08
  543. #define DEFAULT_Kd 114.00
  544. #endif
  545. #endif // PIDTEMP
  546. //===========================================================================
  547. //====================== PID > Bed Temperature Control ======================
  548. //===========================================================================
  549. /**
  550. * PID Bed Heating
  551. *
  552. * If this option is enabled set PID constants below.
  553. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  554. *
  555. * The PID frequency will be the same as the extruder PWM.
  556. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  557. * which is fine for driving a square wave into a resistive load and does not significantly
  558. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  559. * heater. If your configuration is significantly different than this and you don't understand
  560. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  561. */
  562. //#define PIDTEMPBED
  563. //#define BED_LIMIT_SWITCHING
  564. /**
  565. * Max Bed Power
  566. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  567. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  568. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  569. */
  570. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  571. #if ENABLED(PIDTEMPBED)
  572. //#define MIN_BED_POWER 0
  573. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  574. // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  575. // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  576. #define DEFAULT_bedKp 10.00
  577. #define DEFAULT_bedKi .023
  578. #define DEFAULT_bedKd 305.4
  579. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  580. #endif // PIDTEMPBED
  581. //===========================================================================
  582. //==================== PID > Chamber Temperature Control ====================
  583. //===========================================================================
  584. /**
  585. * PID Chamber Heating
  586. *
  587. * If this option is enabled set PID constants below.
  588. * If this option is disabled, bang-bang will be used and CHAMBER_LIMIT_SWITCHING will enable
  589. * hysteresis.
  590. *
  591. * The PID frequency will be the same as the extruder PWM.
  592. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  593. * which is fine for driving a square wave into a resistive load and does not significantly
  594. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
  595. * heater. If your configuration is significantly different than this and you don't understand
  596. * the issues involved, don't use chamber PID until someone else verifies that your hardware works.
  597. */
  598. //#define PIDTEMPCHAMBER
  599. //#define CHAMBER_LIMIT_SWITCHING
  600. /**
  601. * Max Chamber Power
  602. * Applies to all forms of chamber control (PID, bang-bang, and bang-bang with hysteresis).
  603. * When set to any value below 255, enables a form of PWM to the chamber heater that acts like a divider
  604. * so don't use it unless you are OK with PWM on your heater. (See the comment on enabling PIDTEMPCHAMBER)
  605. */
  606. #define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
  607. #if ENABLED(PIDTEMPCHAMBER)
  608. #define MIN_CHAMBER_POWER 0
  609. //#define PID_CHAMBER_DEBUG // Sends debug data to the serial port.
  610. // Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
  611. // and placed inside the small Creality printer enclosure tent.
  612. //
  613. #define DEFAULT_chamberKp 37.04
  614. #define DEFAULT_chamberKi 1.40
  615. #define DEFAULT_chamberKd 655.17
  616. // M309 P37.04 I1.04 D655.17
  617. // FIND YOUR OWN: "M303 E-2 C8 S50" to run autotune on the chamber at 50 degreesC for 8 cycles.
  618. #endif // PIDTEMPCHAMBER
  619. #if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
  620. //#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
  621. //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  622. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  623. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  624. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  625. #endif
  626. // @section extruder
  627. /**
  628. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  629. * Add M302 to set the minimum extrusion temperature and/or turn
  630. * cold extrusion prevention on and off.
  631. *
  632. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  633. */
  634. #define PREVENT_COLD_EXTRUSION
  635. #define EXTRUDE_MINTEMP 170
  636. /**
  637. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  638. * Note: For Bowden Extruders make this large enough to allow load/unload.
  639. */
  640. #define PREVENT_LENGTHY_EXTRUDE
  641. #define EXTRUDE_MAXLENGTH 200
  642. //===========================================================================
  643. //======================== Thermal Runaway Protection =======================
  644. //===========================================================================
  645. /**
  646. * Thermal Protection provides additional protection to your printer from damage
  647. * and fire. Marlin always includes safe min and max temperature ranges which
  648. * protect against a broken or disconnected thermistor wire.
  649. *
  650. * The issue: If a thermistor falls out, it will report the much lower
  651. * temperature of the air in the room, and the the firmware will keep
  652. * the heater on.
  653. *
  654. * If you get "Thermal Runaway" or "Heating failed" errors the
  655. * details can be tuned in Configuration_adv.h
  656. */
  657. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  658. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  659. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  660. #define THERMAL_PROTECTION_COOLER // Enable thermal protection for the laser cooling
  661. //===========================================================================
  662. //============================= Mechanical Settings =========================
  663. //===========================================================================
  664. // @section machine
  665. // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
  666. // either in the usual order or reversed
  667. //#define COREXY
  668. //#define COREXZ
  669. //#define COREYZ
  670. //#define COREYX
  671. //#define COREZX
  672. //#define COREZY
  673. //#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042
  674. //#define MARKFORGED_YX
  675. // Enable for a belt style printer with endless "Z" motion
  676. //#define BELTPRINTER
  677. // Enable for Polargraph Kinematics
  678. //#define POLARGRAPH
  679. #if ENABLED(POLARGRAPH)
  680. #define POLARGRAPH_MAX_BELT_LEN 1035.0
  681. #define POLAR_SEGMENTS_PER_SECOND 5
  682. #endif
  683. //===========================================================================
  684. //============================== Endstop Settings ===========================
  685. //===========================================================================
  686. // @section homing
  687. // Specify here all the endstop connectors that are connected to any endstop or probe.
  688. // Almost all printers will be using one per axis. Probes will use one or more of the
  689. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  690. #define USE_XMIN_PLUG
  691. #define USE_YMIN_PLUG
  692. #define USE_ZMIN_PLUG
  693. //#define USE_IMIN_PLUG
  694. //#define USE_JMIN_PLUG
  695. //#define USE_KMIN_PLUG
  696. //#define USE_XMAX_PLUG
  697. //#define USE_YMAX_PLUG
  698. //#define USE_ZMAX_PLUG
  699. //#define USE_IMAX_PLUG
  700. //#define USE_JMAX_PLUG
  701. //#define USE_KMAX_PLUG
  702. // Enable pullup for all endstops to prevent a floating state
  703. #define ENDSTOPPULLUPS
  704. #if DISABLED(ENDSTOPPULLUPS)
  705. // Disable ENDSTOPPULLUPS to set pullups individually
  706. //#define ENDSTOPPULLUP_XMIN
  707. //#define ENDSTOPPULLUP_YMIN
  708. //#define ENDSTOPPULLUP_ZMIN
  709. //#define ENDSTOPPULLUP_IMIN
  710. //#define ENDSTOPPULLUP_JMIN
  711. //#define ENDSTOPPULLUP_KMIN
  712. //#define ENDSTOPPULLUP_XMAX
  713. //#define ENDSTOPPULLUP_YMAX
  714. //#define ENDSTOPPULLUP_ZMAX
  715. //#define ENDSTOPPULLUP_IMAX
  716. //#define ENDSTOPPULLUP_JMAX
  717. //#define ENDSTOPPULLUP_KMAX
  718. //#define ENDSTOPPULLUP_ZMIN_PROBE
  719. #endif
  720. // Enable pulldown for all endstops to prevent a floating state
  721. //#define ENDSTOPPULLDOWNS
  722. #if DISABLED(ENDSTOPPULLDOWNS)
  723. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  724. //#define ENDSTOPPULLDOWN_XMIN
  725. //#define ENDSTOPPULLDOWN_YMIN
  726. //#define ENDSTOPPULLDOWN_ZMIN
  727. //#define ENDSTOPPULLDOWN_IMIN
  728. //#define ENDSTOPPULLDOWN_JMIN
  729. //#define ENDSTOPPULLDOWN_KMIN
  730. //#define ENDSTOPPULLDOWN_XMAX
  731. //#define ENDSTOPPULLDOWN_YMAX
  732. //#define ENDSTOPPULLDOWN_ZMAX
  733. //#define ENDSTOPPULLDOWN_IMAX
  734. //#define ENDSTOPPULLDOWN_JMAX
  735. //#define ENDSTOPPULLDOWN_KMAX
  736. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  737. #endif
  738. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  739. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  740. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  741. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  742. #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  743. #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  744. #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  745. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  746. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  747. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  748. #define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  749. #define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  750. #define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  751. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  752. /**
  753. * Stepper Drivers
  754. *
  755. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  756. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  757. *
  758. * A4988 is assumed for unspecified drivers.
  759. *
  760. * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  761. *
  762. * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
  763. * TB6560, TB6600, TMC2100,
  764. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  765. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  766. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  767. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  768. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  769. */
  770. #define X_DRIVER_TYPE A4988
  771. #define Y_DRIVER_TYPE A4988
  772. #define Z_DRIVER_TYPE A4988
  773. //#define X2_DRIVER_TYPE A4988
  774. //#define Y2_DRIVER_TYPE A4988
  775. //#define Z2_DRIVER_TYPE A4988
  776. //#define Z3_DRIVER_TYPE A4988
  777. //#define Z4_DRIVER_TYPE A4988
  778. //#define I_DRIVER_TYPE A4988
  779. //#define J_DRIVER_TYPE A4988
  780. //#define K_DRIVER_TYPE A4988
  781. #define E0_DRIVER_TYPE A4988
  782. //#define E1_DRIVER_TYPE A4988
  783. //#define E2_DRIVER_TYPE A4988
  784. //#define E3_DRIVER_TYPE A4988
  785. //#define E4_DRIVER_TYPE A4988
  786. //#define E5_DRIVER_TYPE A4988
  787. //#define E6_DRIVER_TYPE A4988
  788. //#define E7_DRIVER_TYPE A4988
  789. // Enable this feature if all enabled endstop pins are interrupt-capable.
  790. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  791. //#define ENDSTOP_INTERRUPTS_FEATURE
  792. /**
  793. * Endstop Noise Threshold
  794. *
  795. * Enable if your probe or endstops falsely trigger due to noise.
  796. *
  797. * - Higher values may affect repeatability or accuracy of some bed probes.
  798. * - To fix noise install a 100nF ceramic capacitor in parallel with the switch.
  799. * - This feature is not required for common micro-switches mounted on PCBs
  800. * based on the Makerbot design, which already have the 100nF capacitor.
  801. *
  802. * :[2,3,4,5,6,7]
  803. */
  804. //#define ENDSTOP_NOISE_THRESHOLD 2
  805. // Check for stuck or disconnected endstops during homing moves.
  806. //#define DETECT_BROKEN_ENDSTOP
  807. //=============================================================================
  808. //============================== Movement Settings ============================
  809. //=============================================================================
  810. // @section motion
  811. /**
  812. * Default Settings
  813. *
  814. * These settings can be reset by M502
  815. *
  816. * Note that if EEPROM is enabled, saved values will override these.
  817. */
  818. /**
  819. * With this option each E stepper can have its own factors for the
  820. * following movement settings. If fewer factors are given than the
  821. * total number of extruders, the last value applies to the rest.
  822. */
  823. //#define DISTINCT_E_FACTORS
  824. /**
  825. * Default Axis Steps Per Unit (steps/mm)
  826. * Override with M92
  827. * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  828. */
  829. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
  830. /**
  831. * Default Max Feed Rate (mm/s)
  832. * Override with M203
  833. * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  834. */
  835. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  836. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  837. #if ENABLED(LIMITED_MAX_FR_EDITING)
  838. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  839. #endif
  840. /**
  841. * Default Max Acceleration (change/s) change = mm/s
  842. * (Maximum start speed for accelerated moves)
  843. * Override with M201
  844. * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  845. */
  846. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  847. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  848. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  849. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  850. #endif
  851. /**
  852. * Default Acceleration (change/s) change = mm/s
  853. * Override with M204
  854. *
  855. * M204 P Acceleration
  856. * M204 R Retract Acceleration
  857. * M204 T Travel Acceleration
  858. */
  859. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  860. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  861. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  862. /**
  863. * Default Jerk limits (mm/s)
  864. * Override with M205 X Y Z E
  865. *
  866. * "Jerk" specifies the minimum speed change that requires acceleration.
  867. * When changing speed and direction, if the difference is less than the
  868. * value set here, it may happen instantaneously.
  869. */
  870. //#define CLASSIC_JERK
  871. #if ENABLED(CLASSIC_JERK)
  872. #define DEFAULT_XJERK 10.0
  873. #define DEFAULT_YJERK 10.0
  874. #define DEFAULT_ZJERK 0.3
  875. //#define DEFAULT_IJERK 0.3
  876. //#define DEFAULT_JJERK 0.3
  877. //#define DEFAULT_KJERK 0.3
  878. //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
  879. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  880. #if ENABLED(LIMITED_JERK_EDITING)
  881. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  882. #endif
  883. #endif
  884. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  885. /**
  886. * Junction Deviation Factor
  887. *
  888. * See:
  889. * https://reprap.org/forum/read.php?1,739819
  890. * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  891. */
  892. #if DISABLED(CLASSIC_JERK)
  893. #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
  894. #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
  895. // for small segments (< 1mm) with large junction angles (> 135°).
  896. #endif
  897. /**
  898. * S-Curve Acceleration
  899. *
  900. * This option eliminates vibration during printing by fitting a Bézier
  901. * curve to move acceleration, producing much smoother direction changes.
  902. *
  903. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  904. */
  905. //#define S_CURVE_ACCELERATION
  906. //===========================================================================
  907. //============================= Z Probe Options =============================
  908. //===========================================================================
  909. // @section probes
  910. //
  911. // See https://marlinfw.org/docs/configuration/probes.html
  912. //
  913. /**
  914. * Enable this option for a probe connected to the Z-MIN pin.
  915. * The probe replaces the Z-MIN endstop and is used for Z homing.
  916. * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  917. */
  918. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  919. // Force the use of the probe for Z-axis homing
  920. //#define USE_PROBE_FOR_Z_HOMING
  921. /**
  922. * Z_MIN_PROBE_PIN
  923. *
  924. * Define this pin if the probe is not connected to Z_MIN_PIN.
  925. * If not defined the default pin for the selected MOTHERBOARD
  926. * will be used. Most of the time the default is what you want.
  927. *
  928. * - The simplest option is to use a free endstop connector.
  929. * - Use 5V for powered (usually inductive) sensors.
  930. *
  931. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  932. * - For simple switches connect...
  933. * - normally-closed switches to GND and D32.
  934. * - normally-open switches to 5V and D32.
  935. */
  936. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  937. /**
  938. * Probe Type
  939. *
  940. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  941. * Activate one of these to use Auto Bed Leveling below.
  942. */
  943. /**
  944. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  945. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  946. * or (with LCD_BED_LEVELING) the LCD controller.
  947. */
  948. //#define PROBE_MANUALLY
  949. /**
  950. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  951. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  952. */
  953. //#define FIX_MOUNTED_PROBE
  954. /**
  955. * Use the nozzle as the probe, as with a conductive
  956. * nozzle system or a piezo-electric smart effector.
  957. */
  958. //#define NOZZLE_AS_PROBE
  959. /**
  960. * Z Servo Probe, such as an endstop switch on a rotating arm.
  961. */
  962. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  963. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  964. /**
  965. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  966. */
  967. //#define BLTOUCH
  968. /**
  969. * MagLev V4 probe by MDD
  970. *
  971. * This probe is deployed and activated by powering a built-in electromagnet.
  972. */
  973. //#define MAGLEV4
  974. #if ENABLED(MAGLEV4)
  975. //#define MAGLEV_TRIGGER_PIN 11 // Set to the connected digital output
  976. #define MAGLEV_TRIGGER_DELAY 15 // Changing this risks overheating the coil
  977. #endif
  978. /**
  979. * Touch-MI Probe by hotends.fr
  980. *
  981. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  982. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  983. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  984. *
  985. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  986. * and a minimum Z_HOMING_HEIGHT of 10.
  987. */
  988. //#define TOUCH_MI_PROBE
  989. #if ENABLED(TOUCH_MI_PROBE)
  990. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  991. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  992. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  993. #endif
  994. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  995. //#define SOLENOID_PROBE
  996. // A sled-mounted probe like those designed by Charles Bell.
  997. //#define Z_PROBE_SLED
  998. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  999. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  1000. //#define RACK_AND_PINION_PROBE
  1001. #if ENABLED(RACK_AND_PINION_PROBE)
  1002. #define Z_PROBE_DEPLOY_X X_MIN_POS
  1003. #define Z_PROBE_RETRACT_X X_MAX_POS
  1004. #endif
  1005. // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
  1006. // When the pin is defined you can use M672 to set/reset the probe sensitivity.
  1007. //#define DUET_SMART_EFFECTOR
  1008. #if ENABLED(DUET_SMART_EFFECTOR)
  1009. #define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin
  1010. #endif
  1011. /**
  1012. * Use StallGuard2 to probe the bed with the nozzle.
  1013. * Requires stallGuard-capable Trinamic stepper drivers.
  1014. * CAUTION: This can damage machines with Z lead screws.
  1015. * Take extreme care when setting up this feature.
  1016. */
  1017. //#define SENSORLESS_PROBING
  1018. //
  1019. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  1020. //
  1021. /**
  1022. * Nozzle-to-Probe offsets { X, Y, Z }
  1023. *
  1024. * X and Y offset
  1025. * Use a caliper or ruler to measure the distance from the tip of
  1026. * the Nozzle to the center-point of the Probe in the X and Y axes.
  1027. *
  1028. * Z offset
  1029. * - For the Z offset use your best known value and adjust at runtime.
  1030. * - Common probes trigger below the nozzle and have negative values for Z offset.
  1031. * - Probes triggering above the nozzle height are uncommon but do exist. When using
  1032. * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES
  1033. * to avoid collisions during probing.
  1034. *
  1035. * Tune and Adjust
  1036. * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc.
  1037. * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset.
  1038. *
  1039. * Assuming the typical work area orientation:
  1040. * - Probe to RIGHT of the Nozzle has a Positive X offset
  1041. * - Probe to LEFT of the Nozzle has a Negative X offset
  1042. * - Probe in BACK of the Nozzle has a Positive Y offset
  1043. * - Probe in FRONT of the Nozzle has a Negative Y offset
  1044. *
  1045. * Some examples:
  1046. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 } // Example "1"
  1047. * #define NOZZLE_TO_PROBE_OFFSET {-10, 5, -1 } // Example "2"
  1048. * #define NOZZLE_TO_PROBE_OFFSET { 5, -5, -1 } // Example "3"
  1049. * #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 } // Example "4"
  1050. *
  1051. * +-- BACK ---+
  1052. * | [+] |
  1053. * L | 1 | R <-- Example "1" (right+, back+)
  1054. * E | 2 | I <-- Example "2" ( left-, back+)
  1055. * F |[-] N [+]| G <-- Nozzle
  1056. * T | 3 | H <-- Example "3" (right+, front-)
  1057. * | 4 | T <-- Example "4" ( left-, front-)
  1058. * | [-] |
  1059. * O-- FRONT --+
  1060. */
  1061. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  1062. // Most probes should stay away from the edges of the bed, but
  1063. // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
  1064. #define PROBING_MARGIN 10
  1065. // X and Y axis travel speed (mm/min) between probes
  1066. #define XY_PROBE_FEEDRATE (133*60)
  1067. // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  1068. #define Z_PROBE_FEEDRATE_FAST (4*60)
  1069. // Feedrate (mm/min) for the "accurate" probe of each point
  1070. #define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
  1071. /**
  1072. * Probe Activation Switch
  1073. * A switch indicating proper deployment, or an optical
  1074. * switch triggered when the carriage is near the bed.
  1075. */
  1076. //#define PROBE_ACTIVATION_SWITCH
  1077. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  1078. #define PROBE_ACTIVATION_SWITCH_STATE LOW // State indicating probe is active
  1079. //#define PROBE_ACTIVATION_SWITCH_PIN PC6 // Override default pin
  1080. #endif
  1081. /**
  1082. * Tare Probe (determine zero-point) prior to each probe.
  1083. * Useful for a strain gauge or piezo sensor that needs to factor out
  1084. * elements such as cables pulling on the carriage.
  1085. */
  1086. //#define PROBE_TARE
  1087. #if ENABLED(PROBE_TARE)
  1088. #define PROBE_TARE_TIME 200 // (ms) Time to hold tare pin
  1089. #define PROBE_TARE_DELAY 200 // (ms) Delay after tare before
  1090. #define PROBE_TARE_STATE HIGH // State to write pin for tare
  1091. //#define PROBE_TARE_PIN PA5 // Override default pin
  1092. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  1093. //#define PROBE_TARE_ONLY_WHILE_INACTIVE // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active
  1094. #endif
  1095. #endif
  1096. /**
  1097. * Probe Enable / Disable
  1098. * The probe only provides a triggered signal when enabled.
  1099. */
  1100. //#define PROBE_ENABLE_DISABLE
  1101. #if ENABLED(PROBE_ENABLE_DISABLE)
  1102. //#define PROBE_ENABLE_PIN -1 // Override the default pin here
  1103. #endif
  1104. /**
  1105. * Multiple Probing
  1106. *
  1107. * You may get improved results by probing 2 or more times.
  1108. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  1109. *
  1110. * A total of 2 does fast/slow probes with a weighted average.
  1111. * A total of 3 or more adds more slow probes, taking the average.
  1112. */
  1113. //#define MULTIPLE_PROBING 2
  1114. //#define EXTRA_PROBING 1
  1115. /**
  1116. * Z probes require clearance when deploying, stowing, and moving between
  1117. * probe points to avoid hitting the bed and other hardware.
  1118. * Servo-mounted probes require extra space for the arm to rotate.
  1119. * Inductive probes need space to keep from triggering early.
  1120. *
  1121. * Use these settings to specify the distance (mm) to raise the probe (or
  1122. * lower the bed). The values set here apply over and above any (negative)
  1123. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  1124. * Only integer values >= 1 are valid here.
  1125. *
  1126. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  1127. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  1128. */
  1129. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  1130. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  1131. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  1132. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  1133. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  1134. // For M851 give a range for adjusting the Z probe offset
  1135. #define Z_PROBE_OFFSET_RANGE_MIN -20
  1136. #define Z_PROBE_OFFSET_RANGE_MAX 20
  1137. // Enable the M48 repeatability test to test probe accuracy
  1138. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  1139. // Before deploy/stow pause for user confirmation
  1140. //#define PAUSE_BEFORE_DEPLOY_STOW
  1141. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  1142. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  1143. #endif
  1144. /**
  1145. * Enable one or more of the following if probing seems unreliable.
  1146. * Heaters and/or fans can be disabled during probing to minimize electrical
  1147. * noise. A delay can also be added to allow noise and vibration to settle.
  1148. * These options are most useful for the BLTouch probe, but may also improve
  1149. * readings with inductive probes and piezo sensors.
  1150. */
  1151. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  1152. #if ENABLED(PROBING_HEATERS_OFF)
  1153. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  1154. //#define WAIT_FOR_HOTEND // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
  1155. #endif
  1156. //#define PROBING_FANS_OFF // Turn fans off when probing
  1157. //#define PROBING_ESTEPPERS_OFF // Turn all extruder steppers off when probing
  1158. //#define PROBING_STEPPERS_OFF // Turn all steppers off (unless needed to hold position) when probing (including extruders)
  1159. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  1160. // Require minimum nozzle and/or bed temperature for probing
  1161. //#define PREHEAT_BEFORE_PROBING
  1162. #if ENABLED(PREHEAT_BEFORE_PROBING)
  1163. #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1164. #define PROBING_BED_TEMP 50
  1165. #endif
  1166. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  1167. // :{ 0:'Low', 1:'High' }
  1168. #define X_ENABLE_ON 0
  1169. #define Y_ENABLE_ON 0
  1170. #define Z_ENABLE_ON 0
  1171. #define E_ENABLE_ON 0 // For all extruders
  1172. //#define I_ENABLE_ON 0
  1173. //#define J_ENABLE_ON 0
  1174. //#define K_ENABLE_ON 0
  1175. // Disable axis steppers immediately when they're not being stepped.
  1176. // WARNING: When motors turn off there is a chance of losing position accuracy!
  1177. #define DISABLE_X false
  1178. #define DISABLE_Y false
  1179. #define DISABLE_Z false
  1180. //#define DISABLE_I false
  1181. //#define DISABLE_J false
  1182. //#define DISABLE_K false
  1183. // Turn off the display blinking that warns about possible accuracy reduction
  1184. //#define DISABLE_REDUCED_ACCURACY_WARNING
  1185. // @section extruder
  1186. #define DISABLE_E false // Disable the extruder when not stepping
  1187. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  1188. // @section machine
  1189. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  1190. #define INVERT_X_DIR false
  1191. #define INVERT_Y_DIR true
  1192. #define INVERT_Z_DIR false
  1193. //#define INVERT_I_DIR false
  1194. //#define INVERT_J_DIR false
  1195. //#define INVERT_K_DIR false
  1196. // @section extruder
  1197. // For direct drive extruder v9 set to true, for geared extruder set to false.
  1198. #define INVERT_E0_DIR false
  1199. #define INVERT_E1_DIR false
  1200. #define INVERT_E2_DIR false
  1201. #define INVERT_E3_DIR false
  1202. #define INVERT_E4_DIR false
  1203. #define INVERT_E5_DIR false
  1204. #define INVERT_E6_DIR false
  1205. #define INVERT_E7_DIR false
  1206. // @section homing
  1207. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
  1208. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
  1209. /**
  1210. * Set Z_IDLE_HEIGHT if the Z-Axis moves on its own when steppers are disabled.
  1211. * - Use a low value (i.e., Z_MIN_POS) if the nozzle falls down to the bed.
  1212. * - Use a large value (i.e., Z_MAX_POS) if the bed falls down, away from the nozzle.
  1213. */
  1214. //#define Z_IDLE_HEIGHT Z_HOME_POS
  1215. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  1216. // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
  1217. //#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
  1218. // Direction of endstops when homing; 1=MAX, -1=MIN
  1219. // :[-1,1]
  1220. #define X_HOME_DIR -1
  1221. #define Y_HOME_DIR -1
  1222. #define Z_HOME_DIR -1
  1223. //#define I_HOME_DIR -1
  1224. //#define J_HOME_DIR -1
  1225. //#define K_HOME_DIR -1
  1226. // @section machine
  1227. // The size of the printable area
  1228. #define X_BED_SIZE 200
  1229. #define Y_BED_SIZE 200
  1230. // Travel limits (mm) after homing, corresponding to endstop positions.
  1231. #define X_MIN_POS 0
  1232. #define Y_MIN_POS 0
  1233. #define Z_MIN_POS 0
  1234. #define X_MAX_POS X_BED_SIZE
  1235. #define Y_MAX_POS Y_BED_SIZE
  1236. #define Z_MAX_POS 200
  1237. //#define I_MIN_POS 0
  1238. //#define I_MAX_POS 50
  1239. //#define J_MIN_POS 0
  1240. //#define J_MAX_POS 50
  1241. //#define K_MIN_POS 0
  1242. //#define K_MAX_POS 50
  1243. /**
  1244. * Software Endstops
  1245. *
  1246. * - Prevent moves outside the set machine bounds.
  1247. * - Individual axes can be disabled, if desired.
  1248. * - X and Y only apply to Cartesian robots.
  1249. * - Use 'M211' to set software endstops on/off or report current state
  1250. */
  1251. // Min software endstops constrain movement within minimum coordinate bounds
  1252. #define MIN_SOFTWARE_ENDSTOPS
  1253. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  1254. #define MIN_SOFTWARE_ENDSTOP_X
  1255. #define MIN_SOFTWARE_ENDSTOP_Y
  1256. #define MIN_SOFTWARE_ENDSTOP_Z
  1257. #define MIN_SOFTWARE_ENDSTOP_I
  1258. #define MIN_SOFTWARE_ENDSTOP_J
  1259. #define MIN_SOFTWARE_ENDSTOP_K
  1260. #endif
  1261. // Max software endstops constrain movement within maximum coordinate bounds
  1262. #define MAX_SOFTWARE_ENDSTOPS
  1263. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  1264. #define MAX_SOFTWARE_ENDSTOP_X
  1265. #define MAX_SOFTWARE_ENDSTOP_Y
  1266. #define MAX_SOFTWARE_ENDSTOP_Z
  1267. #define MAX_SOFTWARE_ENDSTOP_I
  1268. #define MAX_SOFTWARE_ENDSTOP_J
  1269. #define MAX_SOFTWARE_ENDSTOP_K
  1270. #endif
  1271. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  1272. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  1273. #endif
  1274. /**
  1275. * Filament Runout Sensors
  1276. * Mechanical or opto endstops are used to check for the presence of filament.
  1277. *
  1278. * IMPORTANT: Runout will only trigger if Marlin is aware that a print job is running.
  1279. * Marlin knows a print job is running when:
  1280. * 1. Running a print job from media started with M24.
  1281. * 2. The Print Job Timer has been started with M75.
  1282. * 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled.
  1283. *
  1284. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  1285. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  1286. */
  1287. //#define FILAMENT_RUNOUT_SENSOR
  1288. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  1289. #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
  1290. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  1291. #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
  1292. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  1293. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  1294. //#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder.
  1295. // This is automatically enabled for MIXING_EXTRUDERs.
  1296. // Override individually if the runout sensors vary
  1297. //#define FIL_RUNOUT1_STATE LOW
  1298. //#define FIL_RUNOUT1_PULLUP
  1299. //#define FIL_RUNOUT1_PULLDOWN
  1300. //#define FIL_RUNOUT2_STATE LOW
  1301. //#define FIL_RUNOUT2_PULLUP
  1302. //#define FIL_RUNOUT2_PULLDOWN
  1303. //#define FIL_RUNOUT3_STATE LOW
  1304. //#define FIL_RUNOUT3_PULLUP
  1305. //#define FIL_RUNOUT3_PULLDOWN
  1306. //#define FIL_RUNOUT4_STATE LOW
  1307. //#define FIL_RUNOUT4_PULLUP
  1308. //#define FIL_RUNOUT4_PULLDOWN
  1309. //#define FIL_RUNOUT5_STATE LOW
  1310. //#define FIL_RUNOUT5_PULLUP
  1311. //#define FIL_RUNOUT5_PULLDOWN
  1312. //#define FIL_RUNOUT6_STATE LOW
  1313. //#define FIL_RUNOUT6_PULLUP
  1314. //#define FIL_RUNOUT6_PULLDOWN
  1315. //#define FIL_RUNOUT7_STATE LOW
  1316. //#define FIL_RUNOUT7_PULLUP
  1317. //#define FIL_RUNOUT7_PULLDOWN
  1318. //#define FIL_RUNOUT8_STATE LOW
  1319. //#define FIL_RUNOUT8_PULLUP
  1320. //#define FIL_RUNOUT8_PULLDOWN
  1321. // Commands to execute on filament runout.
  1322. // With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
  1323. // NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
  1324. #define FILAMENT_RUNOUT_SCRIPT "M600"
  1325. // After a runout is detected, continue printing this length of filament
  1326. // before executing the runout script. Useful for a sensor at the end of
  1327. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  1328. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  1329. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  1330. // Enable this option to use an encoder disc that toggles the runout pin
  1331. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  1332. // large enough to avoid false positives.)
  1333. //#define FILAMENT_MOTION_SENSOR
  1334. #endif
  1335. #endif
  1336. //===========================================================================
  1337. //=============================== Bed Leveling ==============================
  1338. //===========================================================================
  1339. // @section calibrate
  1340. /**
  1341. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  1342. * and behavior of G29 will change depending on your selection.
  1343. *
  1344. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  1345. *
  1346. * - AUTO_BED_LEVELING_3POINT
  1347. * Probe 3 arbitrary points on the bed (that aren't collinear)
  1348. * You specify the XY coordinates of all 3 points.
  1349. * The result is a single tilted plane. Best for a flat bed.
  1350. *
  1351. * - AUTO_BED_LEVELING_LINEAR
  1352. * Probe several points in a grid.
  1353. * You specify the rectangle and the density of sample points.
  1354. * The result is a single tilted plane. Best for a flat bed.
  1355. *
  1356. * - AUTO_BED_LEVELING_BILINEAR
  1357. * Probe several points in a grid.
  1358. * You specify the rectangle and the density of sample points.
  1359. * The result is a mesh, best for large or uneven beds.
  1360. *
  1361. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1362. * A comprehensive bed leveling system combining the features and benefits
  1363. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1364. * Validation and Mesh Editing systems.
  1365. *
  1366. * - MESH_BED_LEVELING
  1367. * Probe a grid manually
  1368. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1369. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1370. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1371. * With an LCD controller the process is guided step-by-step.
  1372. */
  1373. //#define AUTO_BED_LEVELING_3POINT
  1374. //#define AUTO_BED_LEVELING_LINEAR
  1375. //#define AUTO_BED_LEVELING_BILINEAR
  1376. //#define AUTO_BED_LEVELING_UBL
  1377. //#define MESH_BED_LEVELING
  1378. /**
  1379. * Normally G28 leaves leveling disabled on completion. Enable one of
  1380. * these options to restore the prior leveling state or to always enable
  1381. * leveling immediately after G28.
  1382. */
  1383. //#define RESTORE_LEVELING_AFTER_G28
  1384. //#define ENABLE_LEVELING_AFTER_G28
  1385. /**
  1386. * Auto-leveling needs preheating
  1387. */
  1388. //#define PREHEAT_BEFORE_LEVELING
  1389. #if ENABLED(PREHEAT_BEFORE_LEVELING)
  1390. #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1391. #define LEVELING_BED_TEMP 50
  1392. #endif
  1393. /**
  1394. * Enable detailed logging of G28, G29, M48, etc.
  1395. * Turn on with the command 'M111 S32'.
  1396. * NOTE: Requires a lot of PROGMEM!
  1397. */
  1398. //#define DEBUG_LEVELING_FEATURE
  1399. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, PROBE_MANUALLY)
  1400. // Set a height for the start of manual adjustment
  1401. #define MANUAL_PROBE_START_Z 0.2 // (mm) Comment out to use the last-measured height
  1402. #endif
  1403. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1404. // Gradually reduce leveling correction until a set height is reached,
  1405. // at which point movement will be level to the machine's XY plane.
  1406. // The height can be set with M420 Z<height>
  1407. #define ENABLE_LEVELING_FADE_HEIGHT
  1408. #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
  1409. #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
  1410. #endif
  1411. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1412. // split up moves into short segments like a Delta. This follows the
  1413. // contours of the bed more closely than edge-to-edge straight moves.
  1414. #define SEGMENT_LEVELED_MOVES
  1415. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1416. /**
  1417. * Enable the G26 Mesh Validation Pattern tool.
  1418. */
  1419. //#define G26_MESH_VALIDATION
  1420. #if ENABLED(G26_MESH_VALIDATION)
  1421. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1422. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
  1423. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26.
  1424. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26.
  1425. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves.
  1426. #define G26_XY_FEEDRATE_TRAVEL 100 // (mm/s) Feedrate for G26 XY travel moves.
  1427. #define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
  1428. #endif
  1429. #endif
  1430. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1431. // Set the number of grid points per dimension.
  1432. #define GRID_MAX_POINTS_X 3
  1433. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1434. // Probe along the Y axis, advancing X after each column
  1435. //#define PROBE_Y_FIRST
  1436. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1437. // Beyond the probed grid, continue the implied tilt?
  1438. // Default is to maintain the height of the nearest edge.
  1439. //#define EXTRAPOLATE_BEYOND_GRID
  1440. //
  1441. // Experimental Subdivision of the grid by Catmull-Rom method.
  1442. // Synthesizes intermediate points to produce a more detailed mesh.
  1443. //
  1444. //#define ABL_BILINEAR_SUBDIVISION
  1445. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1446. // Number of subdivisions between probe points
  1447. #define BILINEAR_SUBDIVISIONS 3
  1448. #endif
  1449. #endif
  1450. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1451. //===========================================================================
  1452. //========================= Unified Bed Leveling ============================
  1453. //===========================================================================
  1454. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1455. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1456. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1457. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1458. //#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
  1459. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1460. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1461. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1462. // as the Z-Height correction value.
  1463. //#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
  1464. #elif ENABLED(MESH_BED_LEVELING)
  1465. //===========================================================================
  1466. //=================================== Mesh ==================================
  1467. //===========================================================================
  1468. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1469. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1470. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1471. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1472. #endif // BED_LEVELING
  1473. /**
  1474. * Add a bed leveling sub-menu for ABL or MBL.
  1475. * Include a guided procedure if manual probing is enabled.
  1476. */
  1477. //#define LCD_BED_LEVELING
  1478. #if ENABLED(LCD_BED_LEVELING)
  1479. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1480. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1481. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1482. #endif
  1483. // Add a menu item to move between bed corners for manual bed adjustment
  1484. //#define LEVEL_BED_CORNERS
  1485. #if ENABLED(LEVEL_BED_CORNERS)
  1486. #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
  1487. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1488. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
  1489. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1490. //#define LEVEL_CORNERS_USE_PROBE
  1491. #if ENABLED(LEVEL_CORNERS_USE_PROBE)
  1492. #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
  1493. #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
  1494. //#define LEVEL_CORNERS_AUDIO_FEEDBACK
  1495. #endif
  1496. /**
  1497. * Corner Leveling Order
  1498. *
  1499. * Set 2 or 4 points. When 2 points are given, the 3rd is the center of the opposite edge.
  1500. *
  1501. * LF Left-Front RF Right-Front
  1502. * LB Left-Back RB Right-Back
  1503. *
  1504. * Examples:
  1505. *
  1506. * Default {LF,RB,LB,RF} {LF,RF} {LB,LF}
  1507. * LB --------- RB LB --------- RB LB --------- RB LB --------- RB
  1508. * | 4 3 | | 3 2 | | <3> | | 1 |
  1509. * | | | | | | | <3>|
  1510. * | 1 2 | | 1 4 | | 1 2 | | 2 |
  1511. * LF --------- RF LF --------- RF LF --------- RF LF --------- RF
  1512. */
  1513. #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB }
  1514. #endif
  1515. /**
  1516. * Commands to execute at the end of G29 probing.
  1517. * Useful to retract or move the Z probe out of the way.
  1518. */
  1519. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1520. // @section homing
  1521. // The center of the bed is at (X=0, Y=0)
  1522. //#define BED_CENTER_AT_0_0
  1523. // Manually set the home position. Leave these undefined for automatic settings.
  1524. // For DELTA this is the top-center of the Cartesian print volume.
  1525. //#define MANUAL_X_HOME_POS 0
  1526. //#define MANUAL_Y_HOME_POS 0
  1527. //#define MANUAL_Z_HOME_POS 0
  1528. //#define MANUAL_I_HOME_POS 0
  1529. //#define MANUAL_J_HOME_POS 0
  1530. //#define MANUAL_K_HOME_POS 0
  1531. /**
  1532. * Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1533. *
  1534. * - Moves the Z probe (or nozzle) to a defined XY point before Z homing.
  1535. * - Allows Z homing only when XY positions are known and trusted.
  1536. * - If stepper drivers sleep, XY homing may be required again before Z homing.
  1537. */
  1538. //#define Z_SAFE_HOMING
  1539. #if ENABLED(Z_SAFE_HOMING)
  1540. #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
  1541. #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
  1542. #endif
  1543. // Homing speeds (mm/min)
  1544. #define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
  1545. // Validate that endstops are triggered on homing moves
  1546. #define VALIDATE_HOMING_ENDSTOPS
  1547. // @section calibrate
  1548. /**
  1549. * Bed Skew Compensation
  1550. *
  1551. * This feature corrects for misalignment in the XYZ axes.
  1552. *
  1553. * Take the following steps to get the bed skew in the XY plane:
  1554. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1555. * 2. For XY_DIAG_AC measure the diagonal A to C
  1556. * 3. For XY_DIAG_BD measure the diagonal B to D
  1557. * 4. For XY_SIDE_AD measure the edge A to D
  1558. *
  1559. * Marlin automatically computes skew factors from these measurements.
  1560. * Skew factors may also be computed and set manually:
  1561. *
  1562. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1563. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1564. *
  1565. * If desired, follow the same procedure for XZ and YZ.
  1566. * Use these diagrams for reference:
  1567. *
  1568. * Y Z Z
  1569. * ^ B-------C ^ B-------C ^ B-------C
  1570. * | / / | / / | / /
  1571. * | / / | / / | / /
  1572. * | A-------D | A-------D | A-------D
  1573. * +-------------->X +-------------->X +-------------->Y
  1574. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1575. */
  1576. //#define SKEW_CORRECTION
  1577. #if ENABLED(SKEW_CORRECTION)
  1578. // Input all length measurements here:
  1579. #define XY_DIAG_AC 282.8427124746
  1580. #define XY_DIAG_BD 282.8427124746
  1581. #define XY_SIDE_AD 200
  1582. // Or, set the default skew factors directly here
  1583. // to override the above measurements:
  1584. #define XY_SKEW_FACTOR 0.0
  1585. //#define SKEW_CORRECTION_FOR_Z
  1586. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1587. #define XZ_DIAG_AC 282.8427124746
  1588. #define XZ_DIAG_BD 282.8427124746
  1589. #define YZ_DIAG_AC 282.8427124746
  1590. #define YZ_DIAG_BD 282.8427124746
  1591. #define YZ_SIDE_AD 200
  1592. #define XZ_SKEW_FACTOR 0.0
  1593. #define YZ_SKEW_FACTOR 0.0
  1594. #endif
  1595. // Enable this option for M852 to set skew at runtime
  1596. //#define SKEW_CORRECTION_GCODE
  1597. #endif
  1598. //=============================================================================
  1599. //============================= Additional Features ===========================
  1600. //=============================================================================
  1601. // @section extras
  1602. /**
  1603. * EEPROM
  1604. *
  1605. * Persistent storage to preserve configurable settings across reboots.
  1606. *
  1607. * M500 - Store settings to EEPROM.
  1608. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1609. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1610. */
  1611. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1612. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1613. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1614. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
  1615. #if ENABLED(EEPROM_SETTINGS)
  1616. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1617. //#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
  1618. #endif
  1619. //
  1620. // Host Keepalive
  1621. //
  1622. // When enabled Marlin will send a busy status message to the host
  1623. // every couple of seconds when it can't accept commands.
  1624. //
  1625. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1626. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1627. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1628. //
  1629. // G20/G21 Inch mode support
  1630. //
  1631. //#define INCH_MODE_SUPPORT
  1632. //
  1633. // M149 Set temperature units support
  1634. //
  1635. //#define TEMPERATURE_UNITS_SUPPORT
  1636. // @section temperature
  1637. //
  1638. // Preheat Constants - Up to 5 are supported without changes
  1639. //
  1640. #define PREHEAT_1_LABEL "PLA"
  1641. #define PREHEAT_1_TEMP_HOTEND 180
  1642. #define PREHEAT_1_TEMP_BED 70
  1643. #define PREHEAT_1_TEMP_CHAMBER 35
  1644. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1645. #define PREHEAT_2_LABEL "ABS"
  1646. #define PREHEAT_2_TEMP_HOTEND 240
  1647. #define PREHEAT_2_TEMP_BED 110
  1648. #define PREHEAT_2_TEMP_CHAMBER 35
  1649. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1650. /**
  1651. * Nozzle Park
  1652. *
  1653. * Park the nozzle at the given XYZ position on idle or G27.
  1654. *
  1655. * The "P" parameter controls the action applied to the Z axis:
  1656. *
  1657. * P0 (Default) If Z is below park Z raise the nozzle.
  1658. * P1 Raise the nozzle always to Z-park height.
  1659. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1660. */
  1661. //#define NOZZLE_PARK_FEATURE
  1662. #if ENABLED(NOZZLE_PARK_FEATURE)
  1663. // Specify a park position as { X, Y, Z_raise }
  1664. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1665. //#define NOZZLE_PARK_X_ONLY // X move only is required to park
  1666. //#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
  1667. #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
  1668. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1669. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1670. #endif
  1671. /**
  1672. * Clean Nozzle Feature -- EXPERIMENTAL
  1673. *
  1674. * Adds the G12 command to perform a nozzle cleaning process.
  1675. *
  1676. * Parameters:
  1677. * P Pattern
  1678. * S Strokes / Repetitions
  1679. * T Triangles (P1 only)
  1680. *
  1681. * Patterns:
  1682. * P0 Straight line (default). This process requires a sponge type material
  1683. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1684. * between the start / end points.
  1685. *
  1686. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1687. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1688. * Zig-zags are done in whichever is the narrower dimension.
  1689. * For example, "G12 P1 S1 T3" will execute:
  1690. *
  1691. * --
  1692. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1693. * | | / \ / \ / \ |
  1694. * A | | / \ / \ / \ |
  1695. * | | / \ / \ / \ |
  1696. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1697. * -- +--------------------------------+
  1698. * |________|_________|_________|
  1699. * T1 T2 T3
  1700. *
  1701. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1702. * "R" specifies the radius. "S" specifies the stroke count.
  1703. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1704. *
  1705. * Caveats: The ending Z should be the same as starting Z.
  1706. * Attention: EXPERIMENTAL. G-code arguments may change.
  1707. */
  1708. //#define NOZZLE_CLEAN_FEATURE
  1709. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1710. // Default number of pattern repetitions
  1711. #define NOZZLE_CLEAN_STROKES 12
  1712. // Default number of triangles
  1713. #define NOZZLE_CLEAN_TRIANGLES 3
  1714. // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
  1715. // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
  1716. #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } }
  1717. #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }
  1718. // Circular pattern radius
  1719. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1720. // Circular pattern circle fragments number
  1721. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1722. // Middle point of circle
  1723. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1724. // Move the nozzle to the initial position after cleaning
  1725. #define NOZZLE_CLEAN_GOBACK
  1726. // For a purge/clean station that's always at the gantry height (thus no Z move)
  1727. //#define NOZZLE_CLEAN_NO_Z
  1728. // For a purge/clean station mounted on the X axis
  1729. //#define NOZZLE_CLEAN_NO_Y
  1730. // Require a minimum hotend temperature for cleaning
  1731. #define NOZZLE_CLEAN_MIN_TEMP 170
  1732. //#define NOZZLE_CLEAN_HEATUP // Heat up the nozzle instead of skipping wipe
  1733. // Explicit wipe G-code script applies to a G12 with no arguments.
  1734. //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0"
  1735. #endif
  1736. /**
  1737. * Print Job Timer
  1738. *
  1739. * Automatically start and stop the print job timer on M104/M109/M140/M190/M141/M191.
  1740. * The print job timer will only be stopped if the bed/chamber target temp is
  1741. * below BED_MINTEMP/CHAMBER_MINTEMP.
  1742. *
  1743. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1744. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1745. * M140 (bed, no wait) - high temp = none, low temp = stop timer
  1746. * M190 (bed, wait) - high temp = start timer, low temp = none
  1747. * M141 (chamber, no wait) - high temp = none, low temp = stop timer
  1748. * M191 (chamber, wait) - high temp = start timer, low temp = none
  1749. *
  1750. * For M104/M109, high temp is anything over EXTRUDE_MINTEMP / 2.
  1751. * For M140/M190, high temp is anything over BED_MINTEMP.
  1752. * For M141/M191, high temp is anything over CHAMBER_MINTEMP.
  1753. *
  1754. * The timer can also be controlled with the following commands:
  1755. *
  1756. * M75 - Start the print job timer
  1757. * M76 - Pause the print job timer
  1758. * M77 - Stop the print job timer
  1759. */
  1760. #define PRINTJOB_TIMER_AUTOSTART
  1761. /**
  1762. * Print Counter
  1763. *
  1764. * Track statistical data such as:
  1765. *
  1766. * - Total print jobs
  1767. * - Total successful print jobs
  1768. * - Total failed print jobs
  1769. * - Total time printing
  1770. *
  1771. * View the current statistics with M78.
  1772. */
  1773. //#define PRINTCOUNTER
  1774. #if ENABLED(PRINTCOUNTER)
  1775. #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
  1776. #endif
  1777. /**
  1778. * Password
  1779. *
  1780. * Set a numerical password for the printer which can be requested:
  1781. *
  1782. * - When the printer boots up
  1783. * - Upon opening the 'Print from Media' Menu
  1784. * - When SD printing is completed or aborted
  1785. *
  1786. * The following G-codes can be used:
  1787. *
  1788. * M510 - Lock Printer. Blocks all commands except M511.
  1789. * M511 - Unlock Printer.
  1790. * M512 - Set, Change and Remove Password.
  1791. *
  1792. * If you forget the password and get locked out you'll need to re-flash
  1793. * the firmware with the feature disabled, reset EEPROM, and (optionally)
  1794. * re-flash the firmware again with this feature enabled.
  1795. */
  1796. //#define PASSWORD_FEATURE
  1797. #if ENABLED(PASSWORD_FEATURE)
  1798. #define PASSWORD_LENGTH 4 // (#) Number of digits (1-9). 3 or 4 is recommended
  1799. #define PASSWORD_ON_STARTUP
  1800. #define PASSWORD_UNLOCK_GCODE // Unlock with the M511 P<password> command. Disable to prevent brute-force attack.
  1801. #define PASSWORD_CHANGE_GCODE // Change the password with M512 P<old> S<new>.
  1802. //#define PASSWORD_ON_SD_PRINT_MENU // This does not prevent gcodes from running
  1803. //#define PASSWORD_AFTER_SD_PRINT_END
  1804. //#define PASSWORD_AFTER_SD_PRINT_ABORT
  1805. //#include "Configuration_Secure.h" // External file with PASSWORD_DEFAULT_VALUE
  1806. #endif
  1807. //=============================================================================
  1808. //============================= LCD and SD support ============================
  1809. //=============================================================================
  1810. // @section lcd
  1811. /**
  1812. * LCD LANGUAGE
  1813. *
  1814. * Select the language to display on the LCD. These languages are available:
  1815. *
  1816. * en, an, bg, ca, cz, da, de, el, el_CY, es, eu, fi, fr, gl, hr, hu, it,
  1817. * jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, sv, tr, uk, vi, zh_CN, zh_TW
  1818. *
  1819. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek (Greece)', 'el_CY':'Greek (Cyprus)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'sv':'Swedish', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)' }
  1820. */
  1821. #define LCD_LANGUAGE en
  1822. /**
  1823. * LCD Character Set
  1824. *
  1825. * Note: This option is NOT applicable to Graphical Displays.
  1826. *
  1827. * All character-based LCDs provide ASCII plus one of these
  1828. * language extensions:
  1829. *
  1830. * - JAPANESE ... the most common
  1831. * - WESTERN ... with more accented characters
  1832. * - CYRILLIC ... for the Russian language
  1833. *
  1834. * To determine the language extension installed on your controller:
  1835. *
  1836. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1837. * - Click the controller to view the LCD menu
  1838. * - The LCD will display Japanese, Western, or Cyrillic text
  1839. *
  1840. * See https://marlinfw.org/docs/development/lcd_language.html
  1841. *
  1842. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1843. */
  1844. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1845. /**
  1846. * Info Screen Style (0:Classic, 1:Průša)
  1847. *
  1848. * :[0:'Classic', 1:'Průša']
  1849. */
  1850. #define LCD_INFO_SCREEN_STYLE 0
  1851. /**
  1852. * SD CARD
  1853. *
  1854. * SD Card support is disabled by default. If your controller has an SD slot,
  1855. * you must uncomment the following option or it won't work.
  1856. */
  1857. //#define SDSUPPORT
  1858. /**
  1859. * SD CARD: ENABLE CRC
  1860. *
  1861. * Use CRC checks and retries on the SD communication.
  1862. */
  1863. //#define SD_CHECK_AND_RETRY
  1864. /**
  1865. * LCD Menu Items
  1866. *
  1867. * Disable all menus and only display the Status Screen, or
  1868. * just remove some extraneous menu items to recover space.
  1869. */
  1870. //#define NO_LCD_MENUS
  1871. //#define SLIM_LCD_MENUS
  1872. //
  1873. // ENCODER SETTINGS
  1874. //
  1875. // This option overrides the default number of encoder pulses needed to
  1876. // produce one step. Should be increased for high-resolution encoders.
  1877. //
  1878. //#define ENCODER_PULSES_PER_STEP 4
  1879. //
  1880. // Use this option to override the number of step signals required to
  1881. // move between next/prev menu items.
  1882. //
  1883. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1884. /**
  1885. * Encoder Direction Options
  1886. *
  1887. * Test your encoder's behavior first with both options disabled.
  1888. *
  1889. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1890. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1891. * Reversed Value Editing only? Enable BOTH options.
  1892. */
  1893. //
  1894. // This option reverses the encoder direction everywhere.
  1895. //
  1896. // Set this option if CLOCKWISE causes values to DECREASE
  1897. //
  1898. //#define REVERSE_ENCODER_DIRECTION
  1899. //
  1900. // This option reverses the encoder direction for navigating LCD menus.
  1901. //
  1902. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1903. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1904. //
  1905. //#define REVERSE_MENU_DIRECTION
  1906. //
  1907. // This option reverses the encoder direction for Select Screen.
  1908. //
  1909. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1910. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1911. //
  1912. //#define REVERSE_SELECT_DIRECTION
  1913. //
  1914. // Individual Axis Homing
  1915. //
  1916. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1917. //
  1918. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1919. //#define INDIVIDUAL_AXIS_HOMING_SUBMENU
  1920. //
  1921. // SPEAKER/BUZZER
  1922. //
  1923. // If you have a speaker that can produce tones, enable it here.
  1924. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1925. //
  1926. //#define SPEAKER
  1927. //
  1928. // The duration and frequency for the UI feedback sound.
  1929. // Set these to 0 to disable audio feedback in the LCD menus.
  1930. //
  1931. // Note: Test audio output with the G-Code:
  1932. // M300 S<frequency Hz> P<duration ms>
  1933. //
  1934. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1935. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1936. //=============================================================================
  1937. //======================== LCD / Controller Selection =========================
  1938. //======================== (Character-based LCDs) =========================
  1939. //=============================================================================
  1940. //
  1941. // RepRapDiscount Smart Controller.
  1942. // https://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1943. //
  1944. // Note: Usually sold with a white PCB.
  1945. //
  1946. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1947. //
  1948. // GT2560 (YHCB2004) LCD Display
  1949. //
  1950. // Requires Testato, Koepel softwarewire library and
  1951. // Andriy Golovnya's LiquidCrystal_AIP31068 library.
  1952. //
  1953. //#define YHCB2004
  1954. //
  1955. // Original RADDS LCD Display+Encoder+SDCardReader
  1956. // http://doku.radds.org/dokumentation/lcd-display/
  1957. //
  1958. //#define RADDS_DISPLAY
  1959. //
  1960. // ULTIMAKER Controller.
  1961. //
  1962. //#define ULTIMAKERCONTROLLER
  1963. //
  1964. // ULTIPANEL as seen on Thingiverse.
  1965. //
  1966. //#define ULTIPANEL
  1967. //
  1968. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1969. // https://reprap.org/wiki/PanelOne
  1970. //
  1971. //#define PANEL_ONE
  1972. //
  1973. // GADGETS3D G3D LCD/SD Controller
  1974. // https://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1975. //
  1976. // Note: Usually sold with a blue PCB.
  1977. //
  1978. //#define G3D_PANEL
  1979. //
  1980. // RigidBot Panel V1.0
  1981. // http://www.inventapart.com/
  1982. //
  1983. //#define RIGIDBOT_PANEL
  1984. //
  1985. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1986. // https://www.aliexpress.com/item/32765887917.html
  1987. //
  1988. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1989. //
  1990. // ANET and Tronxy 20x4 Controller
  1991. //
  1992. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1993. // This LCD is known to be susceptible to electrical interference
  1994. // which scrambles the display. Pressing any button clears it up.
  1995. // This is a LCD2004 display with 5 analog buttons.
  1996. //
  1997. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1998. //
  1999. //#define ULTRA_LCD
  2000. //=============================================================================
  2001. //======================== LCD / Controller Selection =========================
  2002. //===================== (I2C and Shift-Register LCDs) =====================
  2003. //=============================================================================
  2004. //
  2005. // CONTROLLER TYPE: I2C
  2006. //
  2007. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  2008. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  2009. //
  2010. //
  2011. // Elefu RA Board Control Panel
  2012. // http://www.elefu.com/index.php?route=product/product&product_id=53
  2013. //
  2014. //#define RA_CONTROL_PANEL
  2015. //
  2016. // Sainsmart (YwRobot) LCD Displays
  2017. //
  2018. // These require F.Malpartida's LiquidCrystal_I2C library
  2019. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  2020. //
  2021. //#define LCD_SAINSMART_I2C_1602
  2022. //#define LCD_SAINSMART_I2C_2004
  2023. //
  2024. // Generic LCM1602 LCD adapter
  2025. //
  2026. //#define LCM1602
  2027. //
  2028. // PANELOLU2 LCD with status LEDs,
  2029. // separate encoder and click inputs.
  2030. //
  2031. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  2032. // For more info: https://github.com/lincomatic/LiquidTWI2
  2033. //
  2034. // Note: The PANELOLU2 encoder click input can either be directly connected to
  2035. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  2036. //
  2037. //#define LCD_I2C_PANELOLU2
  2038. //
  2039. // Panucatt VIKI LCD with status LEDs,
  2040. // integrated click & L/R/U/D buttons, separate encoder inputs.
  2041. //
  2042. //#define LCD_I2C_VIKI
  2043. //
  2044. // CONTROLLER TYPE: Shift register panels
  2045. //
  2046. //
  2047. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  2048. // LCD configuration: https://reprap.org/wiki/SAV_3D_LCD
  2049. //
  2050. //#define SAV_3DLCD
  2051. //
  2052. // 3-wire SR LCD with strobe using 74HC4094
  2053. // https://github.com/mikeshub/SailfishLCD
  2054. // Uses the code directly from Sailfish
  2055. //
  2056. //#define FF_INTERFACEBOARD
  2057. //
  2058. // TFT GLCD Panel with Marlin UI
  2059. // Panel connected to main board by SPI or I2C interface.
  2060. // See https://github.com/Serhiy-K/TFTGLCDAdapter
  2061. //
  2062. //#define TFTGLCD_PANEL_SPI
  2063. //#define TFTGLCD_PANEL_I2C
  2064. //=============================================================================
  2065. //======================= LCD / Controller Selection =======================
  2066. //========================= (Graphical LCDs) ========================
  2067. //=============================================================================
  2068. //
  2069. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  2070. //
  2071. // IMPORTANT: The U8glib library is required for Graphical Display!
  2072. // https://github.com/olikraus/U8glib_Arduino
  2073. //
  2074. // NOTE: If the LCD is unresponsive you may need to reverse the plugs.
  2075. //
  2076. //
  2077. // RepRapDiscount FULL GRAPHIC Smart Controller
  2078. // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  2079. //
  2080. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  2081. //
  2082. // K.3D Full Graphic Smart Controller
  2083. //
  2084. //#define K3D_FULL_GRAPHIC_SMART_CONTROLLER
  2085. //
  2086. // ReprapWorld Graphical LCD
  2087. // https://reprapworld.com/?products_details&products_id/1218
  2088. //
  2089. //#define REPRAPWORLD_GRAPHICAL_LCD
  2090. //
  2091. // Activate one of these if you have a Panucatt Devices
  2092. // Viki 2.0 or mini Viki with Graphic LCD
  2093. // https://www.panucatt.com
  2094. //
  2095. //#define VIKI2
  2096. //#define miniVIKI
  2097. //
  2098. // Alfawise Ex8 printer LCD marked as WYH L12864 COG
  2099. //
  2100. //#define WYH_L12864
  2101. //
  2102. // MakerLab Mini Panel with graphic
  2103. // controller and SD support - https://reprap.org/wiki/Mini_panel
  2104. //
  2105. //#define MINIPANEL
  2106. //
  2107. // MaKr3d Makr-Panel with graphic controller and SD support.
  2108. // https://reprap.org/wiki/MaKr3d_MaKrPanel
  2109. //
  2110. //#define MAKRPANEL
  2111. //
  2112. // Adafruit ST7565 Full Graphic Controller.
  2113. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  2114. //
  2115. //#define ELB_FULL_GRAPHIC_CONTROLLER
  2116. //
  2117. // BQ LCD Smart Controller shipped by
  2118. // default with the BQ Hephestos 2 and Witbox 2.
  2119. //
  2120. //#define BQ_LCD_SMART_CONTROLLER
  2121. //
  2122. // Cartesio UI
  2123. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  2124. //
  2125. //#define CARTESIO_UI
  2126. //
  2127. // LCD for Melzi Card with Graphical LCD
  2128. //
  2129. //#define LCD_FOR_MELZI
  2130. //
  2131. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  2132. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  2133. //
  2134. //#define ULTI_CONTROLLER
  2135. //
  2136. // MKS MINI12864 with graphic controller and SD support
  2137. // https://reprap.org/wiki/MKS_MINI_12864
  2138. //
  2139. //#define MKS_MINI_12864
  2140. //
  2141. // MKS MINI12864 V3 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
  2142. //
  2143. //#define MKS_MINI_12864_V3
  2144. //
  2145. // MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout.
  2146. // https://www.aliexpress.com/item/33018110072.html
  2147. //
  2148. //#define MKS_LCD12864A
  2149. //#define MKS_LCD12864B
  2150. //
  2151. // FYSETC variant of the MINI12864 graphic controller with SD support
  2152. // https://wiki.fysetc.com/Mini12864_Panel/
  2153. //
  2154. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  2155. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  2156. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  2157. //#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight
  2158. //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight.
  2159. //
  2160. // BigTreeTech Mini 12864 V1.0 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
  2161. //
  2162. //#define BTT_MINI_12864_V1
  2163. //
  2164. // Factory display for Creality CR-10
  2165. // https://www.aliexpress.com/item/32833148327.html
  2166. //
  2167. // This is RAMPS-compatible using a single 10-pin connector.
  2168. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  2169. //
  2170. //#define CR10_STOCKDISPLAY
  2171. //
  2172. // Ender-2 OEM display, a variant of the MKS_MINI_12864
  2173. //
  2174. //#define ENDER2_STOCKDISPLAY
  2175. //
  2176. // ANET and Tronxy Graphical Controller
  2177. //
  2178. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  2179. // A clone of the RepRapDiscount full graphics display but with
  2180. // different pins/wiring (see pins_ANET_10.h). Enable one of these.
  2181. //
  2182. //#define ANET_FULL_GRAPHICS_LCD
  2183. //#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING
  2184. //
  2185. // AZSMZ 12864 LCD with SD
  2186. // https://www.aliexpress.com/item/32837222770.html
  2187. //
  2188. //#define AZSMZ_12864
  2189. //
  2190. // Silvergate GLCD controller
  2191. // https://github.com/android444/Silvergate
  2192. //
  2193. //#define SILVER_GATE_GLCD_CONTROLLER
  2194. //=============================================================================
  2195. //============================== OLED Displays ==============================
  2196. //=============================================================================
  2197. //
  2198. // SSD1306 OLED full graphics generic display
  2199. //
  2200. //#define U8GLIB_SSD1306
  2201. //
  2202. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  2203. //
  2204. //#define SAV_3DGLCD
  2205. #if ENABLED(SAV_3DGLCD)
  2206. #define U8GLIB_SSD1306
  2207. //#define U8GLIB_SH1106
  2208. #endif
  2209. //
  2210. // TinyBoy2 128x64 OLED / Encoder Panel
  2211. //
  2212. //#define OLED_PANEL_TINYBOY2
  2213. //
  2214. // MKS OLED 1.3" 128×64 Full Graphics Controller
  2215. // https://reprap.org/wiki/MKS_12864OLED
  2216. //
  2217. // Tiny, but very sharp OLED display
  2218. //
  2219. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  2220. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  2221. //
  2222. // Zonestar OLED 128×64 Full Graphics Controller
  2223. //
  2224. //#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller
  2225. //#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default)
  2226. //#define ZONESTAR_12864OLED_SSD1306 // 0.96" OLED with SSD1306 controller
  2227. //
  2228. // Einstart S OLED SSD1306
  2229. //
  2230. //#define U8GLIB_SH1106_EINSTART
  2231. //
  2232. // Overlord OLED display/controller with i2c buzzer and LEDs
  2233. //
  2234. //#define OVERLORD_OLED
  2235. //
  2236. // FYSETC OLED 2.42" 128×64 Full Graphics Controller with WS2812 RGB
  2237. // Where to find : https://www.aliexpress.com/item/4000345255731.html
  2238. //#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller
  2239. //
  2240. // K.3D SSD1309 OLED 2.42" 128×64 Full Graphics Controller
  2241. //
  2242. //#define K3D_242_OLED_CONTROLLER // Software SPI
  2243. //=============================================================================
  2244. //========================== Extensible UI Displays ===========================
  2245. //=============================================================================
  2246. //
  2247. // DGUS Touch Display with DWIN OS. (Choose one.)
  2248. // ORIGIN : https://www.aliexpress.com/item/32993409517.html
  2249. // FYSETC : https://www.aliexpress.com/item/32961471929.html
  2250. // MKS : https://www.aliexpress.com/item/1005002008179262.html
  2251. //
  2252. // Flash display with DGUS Displays for Marlin:
  2253. // - Format the SD card to FAT32 with an allocation size of 4kb.
  2254. // - Download files as specified for your type of display.
  2255. // - Plug the microSD card into the back of the display.
  2256. // - Boot the display and wait for the update to complete.
  2257. //
  2258. // ORIGIN (Marlin DWIN_SET)
  2259. // - Download https://github.com/coldtobi/Marlin_DGUS_Resources
  2260. // - Copy the downloaded DWIN_SET folder to the SD card.
  2261. //
  2262. // FYSETC (Supplier default)
  2263. // - Download https://github.com/FYSETC/FYSTLCD-2.0
  2264. // - Copy the downloaded SCREEN folder to the SD card.
  2265. //
  2266. // HIPRECY (Supplier default)
  2267. // - Download https://github.com/HiPrecy/Touch-Lcd-LEO
  2268. // - Copy the downloaded DWIN_SET folder to the SD card.
  2269. //
  2270. // MKS (MKS-H43) (Supplier default)
  2271. // - Download https://github.com/makerbase-mks/MKS-H43
  2272. // - Copy the downloaded DWIN_SET folder to the SD card.
  2273. //
  2274. // RELOADED (T5UID1)
  2275. // - Download https://github.com/Desuuuu/DGUS-reloaded/releases
  2276. // - Copy the downloaded DWIN_SET folder to the SD card.
  2277. //
  2278. //#define DGUS_LCD_UI_ORIGIN
  2279. //#define DGUS_LCD_UI_FYSETC
  2280. //#define DGUS_LCD_UI_HIPRECY
  2281. //#define DGUS_LCD_UI_MKS
  2282. //#define DGUS_LCD_UI_RELOADED
  2283. #if ENABLED(DGUS_LCD_UI_MKS)
  2284. #define USE_MKS_GREEN_UI
  2285. #endif
  2286. //
  2287. // Touch-screen LCD for Malyan M200/M300 printers
  2288. //
  2289. //#define MALYAN_LCD
  2290. #if ENABLED(MALYAN_LCD)
  2291. #define LCD_SERIAL_PORT 1 // Default is 1 for Malyan M200
  2292. #endif
  2293. //
  2294. // Touch UI for FTDI EVE (FT800/FT810) displays
  2295. // See Configuration_adv.h for all configuration options.
  2296. //
  2297. //#define TOUCH_UI_FTDI_EVE
  2298. //
  2299. // Touch-screen LCD for Anycubic printers
  2300. //
  2301. //#define ANYCUBIC_LCD_I3MEGA
  2302. //#define ANYCUBIC_LCD_CHIRON
  2303. #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
  2304. #define LCD_SERIAL_PORT 3 // Default is 3 for Anycubic
  2305. //#define ANYCUBIC_LCD_DEBUG
  2306. #endif
  2307. //
  2308. // 320x240 Nextion 2.8" serial TFT Resistive Touch Screen NX3224T028
  2309. //
  2310. //#define NEXTION_TFT
  2311. #if ENABLED(NEXTION_TFT)
  2312. #define LCD_SERIAL_PORT 1 // Default is 1 for Nextion
  2313. #endif
  2314. //
  2315. // Third-party or vendor-customized controller interfaces.
  2316. // Sources should be installed in 'src/lcd/extui'.
  2317. //
  2318. //#define EXTENSIBLE_UI
  2319. #if ENABLED(EXTENSIBLE_UI)
  2320. //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display
  2321. #endif
  2322. //=============================================================================
  2323. //=============================== Graphical TFTs ==============================
  2324. //=============================================================================
  2325. /**
  2326. * Specific TFT Model Presets. Enable one of the following options
  2327. * or enable TFT_GENERIC and set sub-options.
  2328. */
  2329. //
  2330. // 480x320, 3.5", SPI Display with Rotary Encoder from MKS
  2331. // Usually paired with MKS Robin Nano V2 & V3
  2332. //
  2333. //#define MKS_TS35_V2_0
  2334. //
  2335. // 320x240, 2.4", FSMC Display From MKS
  2336. // Usually paired with MKS Robin Nano V1.2
  2337. //
  2338. //#define MKS_ROBIN_TFT24
  2339. //
  2340. // 320x240, 2.8", FSMC Display From MKS
  2341. // Usually paired with MKS Robin Nano V1.2
  2342. //
  2343. //#define MKS_ROBIN_TFT28
  2344. //
  2345. // 320x240, 3.2", FSMC Display From MKS
  2346. // Usually paired with MKS Robin Nano V1.2
  2347. //
  2348. //#define MKS_ROBIN_TFT32
  2349. //
  2350. // 480x320, 3.5", FSMC Display From MKS
  2351. // Usually paired with MKS Robin Nano V1.2
  2352. //
  2353. //#define MKS_ROBIN_TFT35
  2354. //
  2355. // 480x272, 4.3", FSMC Display From MKS
  2356. //
  2357. //#define MKS_ROBIN_TFT43
  2358. //
  2359. // 320x240, 3.2", FSMC Display From MKS
  2360. // Usually paired with MKS Robin
  2361. //
  2362. //#define MKS_ROBIN_TFT_V1_1R
  2363. //
  2364. // 480x320, 3.5", FSMC Stock Display from TronxXY
  2365. //
  2366. //#define TFT_TRONXY_X5SA
  2367. //
  2368. // 480x320, 3.5", FSMC Stock Display from AnyCubic
  2369. //
  2370. //#define ANYCUBIC_TFT35
  2371. //
  2372. // 320x240, 2.8", FSMC Stock Display from Longer/Alfawise
  2373. //
  2374. //#define LONGER_LK_TFT28
  2375. //
  2376. // 320x240, 2.8", FSMC Stock Display from ET4
  2377. //
  2378. //#define ANET_ET4_TFT28
  2379. //
  2380. // 480x320, 3.5", FSMC Stock Display from ET5
  2381. //
  2382. //#define ANET_ET5_TFT35
  2383. //
  2384. // 1024x600, 7", RGB Stock Display with Rotary Encoder from BIQU-BX
  2385. //
  2386. //#define BIQU_BX_TFT70
  2387. //
  2388. // 480x320, 3.5", SPI Stock Display with Rotary Encoder from BIQU B1 SE Series
  2389. //
  2390. //#define BTT_TFT35_SPI_V1_0
  2391. //
  2392. // Generic TFT with detailed options
  2393. //
  2394. //#define TFT_GENERIC
  2395. #if ENABLED(TFT_GENERIC)
  2396. // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
  2397. #define TFT_DRIVER AUTO
  2398. // Interface. Enable one of the following options:
  2399. //#define TFT_INTERFACE_FSMC
  2400. //#define TFT_INTERFACE_SPI
  2401. // TFT Resolution. Enable one of the following options:
  2402. //#define TFT_RES_320x240
  2403. //#define TFT_RES_480x272
  2404. //#define TFT_RES_480x320
  2405. //#define TFT_RES_1024x600
  2406. #endif
  2407. /**
  2408. * TFT UI - User Interface Selection. Enable one of the following options:
  2409. *
  2410. * TFT_CLASSIC_UI - Emulated DOGM - 128x64 Upscaled
  2411. * TFT_COLOR_UI - Marlin Default Menus, Touch Friendly, using full TFT capabilities
  2412. * TFT_LVGL_UI - A Modern UI using LVGL
  2413. *
  2414. * For LVGL_UI also copy the 'assets' folder from the build directory to the
  2415. * root of your SD card, together with the compiled firmware.
  2416. */
  2417. //#define TFT_CLASSIC_UI
  2418. //#define TFT_COLOR_UI
  2419. //#define TFT_LVGL_UI
  2420. #if ENABLED(TFT_LVGL_UI)
  2421. //#define MKS_WIFI_MODULE // MKS WiFi module
  2422. #endif
  2423. /**
  2424. * TFT Rotation. Set to one of the following values:
  2425. *
  2426. * TFT_ROTATE_90, TFT_ROTATE_90_MIRROR_X, TFT_ROTATE_90_MIRROR_Y,
  2427. * TFT_ROTATE_180, TFT_ROTATE_180_MIRROR_X, TFT_ROTATE_180_MIRROR_Y,
  2428. * TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y,
  2429. * TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION
  2430. */
  2431. //#define TFT_ROTATION TFT_NO_ROTATION
  2432. //=============================================================================
  2433. //============================ Other Controllers ============================
  2434. //=============================================================================
  2435. //
  2436. // Ender-3 v2 OEM display. A DWIN display with Rotary Encoder.
  2437. //
  2438. //#define DWIN_CREALITY_LCD // Creality UI
  2439. //#define DWIN_CREALITY_LCD_ENHANCED // Enhanced UI
  2440. //#define DWIN_CREALITY_LCD_JYERSUI // Jyers UI by Jacob Myers
  2441. //#define DWIN_MARLINUI_PORTRAIT // MarlinUI (portrait orientation)
  2442. //#define DWIN_MARLINUI_LANDSCAPE // MarlinUI (landscape orientation)
  2443. //
  2444. // Touch Screen Settings
  2445. //
  2446. //#define TOUCH_SCREEN
  2447. #if ENABLED(TOUCH_SCREEN)
  2448. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  2449. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  2450. //#define TOUCH_IDLE_SLEEP 300 // (secs) Turn off the TFT backlight if set (5mn)
  2451. #define TOUCH_SCREEN_CALIBRATION
  2452. //#define TOUCH_CALIBRATION_X 12316
  2453. //#define TOUCH_CALIBRATION_Y -8981
  2454. //#define TOUCH_OFFSET_X -43
  2455. //#define TOUCH_OFFSET_Y 257
  2456. //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
  2457. #if BOTH(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
  2458. #define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
  2459. #endif
  2460. #if ENABLED(TFT_COLOR_UI)
  2461. //#define SINGLE_TOUCH_NAVIGATION
  2462. #endif
  2463. #endif
  2464. //
  2465. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  2466. // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
  2467. //
  2468. //#define REPRAPWORLD_KEYPAD
  2469. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  2470. //
  2471. // EasyThreeD ET-4000+ with button input and status LED
  2472. //
  2473. //#define EASYTHREED_UI
  2474. //=============================================================================
  2475. //=============================== Extra Features ==============================
  2476. //=============================================================================
  2477. // @section extras
  2478. // Set number of user-controlled fans. Disable to use all board-defined fans.
  2479. // :[1,2,3,4,5,6,7,8]
  2480. //#define NUM_M106_FANS 1
  2481. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  2482. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  2483. // is too low, you should also increment SOFT_PWM_SCALE.
  2484. //#define FAN_SOFT_PWM
  2485. // Incrementing this by 1 will double the software PWM frequency,
  2486. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  2487. // However, control resolution will be halved for each increment;
  2488. // at zero value, there are 128 effective control positions.
  2489. // :[0,1,2,3,4,5,6,7]
  2490. #define SOFT_PWM_SCALE 0
  2491. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  2492. // be used to mitigate the associated resolution loss. If enabled,
  2493. // some of the PWM cycles are stretched so on average the desired
  2494. // duty cycle is attained.
  2495. //#define SOFT_PWM_DITHER
  2496. // Temperature status LEDs that display the hotend and bed temperature.
  2497. // If all hotends, bed temperature, and target temperature are under 54C
  2498. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  2499. //#define TEMP_STAT_LEDS
  2500. // Support for the BariCUDA Paste Extruder
  2501. //#define BARICUDA
  2502. // Support for BlinkM/CyzRgb
  2503. //#define BLINKM
  2504. // Support for PCA9632 PWM LED driver
  2505. //#define PCA9632
  2506. // Support for PCA9533 PWM LED driver
  2507. //#define PCA9533
  2508. /**
  2509. * RGB LED / LED Strip Control
  2510. *
  2511. * Enable support for an RGB LED connected to 5V digital pins, or
  2512. * an RGB Strip connected to MOSFETs controlled by digital pins.
  2513. *
  2514. * Adds the M150 command to set the LED (or LED strip) color.
  2515. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  2516. * luminance values can be set from 0 to 255.
  2517. * For NeoPixel LED an overall brightness parameter is also available.
  2518. *
  2519. * *** CAUTION ***
  2520. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  2521. * as the Arduino cannot handle the current the LEDs will require.
  2522. * Failure to follow this precaution can destroy your Arduino!
  2523. * NOTE: A separate 5V power supply is required! The NeoPixel LED needs
  2524. * more current than the Arduino 5V linear regulator can produce.
  2525. * *** CAUTION ***
  2526. *
  2527. * LED Type. Enable only one of the following two options.
  2528. */
  2529. //#define RGB_LED
  2530. //#define RGBW_LED
  2531. #if EITHER(RGB_LED, RGBW_LED)
  2532. //#define RGB_LED_R_PIN 34
  2533. //#define RGB_LED_G_PIN 43
  2534. //#define RGB_LED_B_PIN 35
  2535. //#define RGB_LED_W_PIN -1
  2536. #endif
  2537. // Support for Adafruit NeoPixel LED driver
  2538. //#define NEOPIXEL_LED
  2539. #if ENABLED(NEOPIXEL_LED)
  2540. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  2541. //#define NEOPIXEL_PIN 4 // LED driving pin
  2542. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  2543. //#define NEOPIXEL2_PIN 5
  2544. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
  2545. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  2546. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  2547. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  2548. // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
  2549. //#define NEOPIXEL2_SEPARATE
  2550. #if ENABLED(NEOPIXEL2_SEPARATE)
  2551. #define NEOPIXEL2_PIXELS 15 // Number of LEDs in the second strip
  2552. #define NEOPIXEL2_BRIGHTNESS 127 // Initial brightness (0-255)
  2553. #define NEOPIXEL2_STARTUP_TEST // Cycle through colors at startup
  2554. #else
  2555. //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel
  2556. #endif
  2557. // Use some of the NeoPixel LEDs for static (background) lighting
  2558. //#define NEOPIXEL_BKGD_INDEX_FIRST 0 // Index of the first background LED
  2559. //#define NEOPIXEL_BKGD_INDEX_LAST 5 // Index of the last background LED
  2560. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  2561. //#define NEOPIXEL_BKGD_ALWAYS_ON // Keep the backlight on when other NeoPixels are off
  2562. #endif
  2563. /**
  2564. * Printer Event LEDs
  2565. *
  2566. * During printing, the LEDs will reflect the printer status:
  2567. *
  2568. * - Gradually change from blue to violet as the heated bed gets to target temp
  2569. * - Gradually change from violet to red as the hotend gets to temperature
  2570. * - Change to white to illuminate work surface
  2571. * - Change to green once print has finished
  2572. * - Turn off after the print has finished and the user has pushed a button
  2573. */
  2574. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  2575. #define PRINTER_EVENT_LEDS
  2576. #endif
  2577. /**
  2578. * Number of servos
  2579. *
  2580. * For some servo-related options NUM_SERVOS will be set automatically.
  2581. * Set this manually if there are extra servos needing manual control.
  2582. * Set to 0 to turn off servo support.
  2583. */
  2584. //#define NUM_SERVOS 3 // Note: Servo index starts with 0 for M280-M282 commands
  2585. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  2586. // 300ms is a good value but you can try less delay.
  2587. // If the servo can't reach the requested position, increase it.
  2588. #define SERVO_DELAY { 300 }
  2589. // Only power servos during movement, otherwise leave off to prevent jitter
  2590. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  2591. // Edit servo angles with M281 and save to EEPROM with M500
  2592. //#define EDITABLE_SERVO_ANGLES
  2593. // Disable servo with M282 to reduce power consumption, noise, and heat when not in use
  2594. //#define SERVO_DETACH_GCODE