My Marlin configs for Fabrikator Mini and CTC i3 Pro B
您最多选择25个主题 主题必须以字母或数字开头,可以包含连字符 (-),并且长度不得超过35个字符

Configuration_adv.h 65KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397139813991400140114021403140414051406140714081409141014111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472147314741475147614771478147914801481148214831484148514861487148814891490149114921493149414951496149714981499150015011502150315041505150615071508150915101511151215131514151515161517151815191520152115221523152415251526152715281529153015311532153315341535153615371538153915401541154215431544154515461547154815491550155115521553155415551556155715581559156015611562156315641565156615671568156915701571157215731574157515761577157815791580158115821583158415851586158715881589159015911592159315941595159615971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration_adv.h
  24. *
  25. * Advanced settings.
  26. * Only change these if you know exactly what you're doing.
  27. * Some of these settings can damage your printer if improperly set!
  28. *
  29. * Basic settings can be found in Configuration.h
  30. *
  31. */
  32. #ifndef CONFIGURATION_ADV_H
  33. #define CONFIGURATION_ADV_H
  34. #define CONFIGURATION_ADV_H_VERSION 020000
  35. // @section temperature
  36. //===========================================================================
  37. //=============================Thermal Settings ============================
  38. //===========================================================================
  39. //
  40. // Hephestos 2 24V heated bed upgrade kit.
  41. // https://store.bq.com/en/heated-bed-kit-hephestos2
  42. //
  43. //#define HEPHESTOS2_HEATED_BED_KIT
  44. #if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
  45. #undef TEMP_SENSOR_BED
  46. #define TEMP_SENSOR_BED 70
  47. #define HEATER_BED_INVERTING true
  48. #endif
  49. #if DISABLED(PIDTEMPBED)
  50. #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
  51. #if ENABLED(BED_LIMIT_SWITCHING)
  52. #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
  53. #endif
  54. #endif
  55. /**
  56. * Thermal Protection provides additional protection to your printer from damage
  57. * and fire. Marlin always includes safe min and max temperature ranges which
  58. * protect against a broken or disconnected thermistor wire.
  59. *
  60. * The issue: If a thermistor falls out, it will report the much lower
  61. * temperature of the air in the room, and the the firmware will keep
  62. * the heater on.
  63. *
  64. * The solution: Once the temperature reaches the target, start observing.
  65. * If the temperature stays too far below the target (hysteresis) for too
  66. * long (period), the firmware will halt the machine as a safety precaution.
  67. *
  68. * If you get false positives for "Thermal Runaway", increase
  69. * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  70. */
  71. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  72. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  73. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  74. /**
  75. * Whenever an M104, M109, or M303 increases the target temperature, the
  76. * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
  77. * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
  78. * requires a hard reset. This test restarts with any M104/M109/M303, but only
  79. * if the current temperature is far enough below the target for a reliable
  80. * test.
  81. *
  82. * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
  83. * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
  84. * below 2.
  85. */
  86. #define WATCH_TEMP_PERIOD 20 // Seconds
  87. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  88. #endif
  89. /**
  90. * Thermal Protection parameters for the bed are just as above for hotends.
  91. */
  92. #if ENABLED(THERMAL_PROTECTION_BED)
  93. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  94. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  95. /**
  96. * As described above, except for the bed (M140/M190/M303).
  97. */
  98. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  99. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  100. #endif
  101. #if ENABLED(PIDTEMP)
  102. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  103. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
  104. //#define PID_EXTRUSION_SCALING
  105. #if ENABLED(PID_EXTRUSION_SCALING)
  106. #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
  107. #define LPQ_MAX_LEN 50
  108. #endif
  109. #endif
  110. /**
  111. * Automatic Temperature:
  112. * The hotend target temperature is calculated by all the buffered lines of gcode.
  113. * The maximum buffered steps/sec of the extruder motor is called "se".
  114. * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
  115. * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
  116. * mintemp and maxtemp. Turn this off by executing M109 without F*
  117. * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
  118. * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
  119. */
  120. #define AUTOTEMP
  121. #if ENABLED(AUTOTEMP)
  122. #define AUTOTEMP_OLDWEIGHT 0.98
  123. #endif
  124. // Show extra position information in M114
  125. //#define M114_DETAIL
  126. // Show Temperature ADC value
  127. // Enable for M105 to include ADC values read from temperature sensors.
  128. //#define SHOW_TEMP_ADC_VALUES
  129. /**
  130. * High Temperature Thermistor Support
  131. *
  132. * Thermistors able to support high temperature tend to have a hard time getting
  133. * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
  134. * will probably be caught when the heating element first turns on during the
  135. * preheating process, which will trigger a min_temp_error as a safety measure
  136. * and force stop everything.
  137. * To circumvent this limitation, we allow for a preheat time (during which,
  138. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  139. * aberrant readings.
  140. *
  141. * If you want to enable this feature for your hotend thermistor(s)
  142. * uncomment and set values > 0 in the constants below
  143. */
  144. // The number of consecutive low temperature errors that can occur
  145. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  146. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  147. // The number of milliseconds a hotend will preheat before starting to check
  148. // the temperature. This value should NOT be set to the time it takes the
  149. // hot end to reach the target temperature, but the time it takes to reach
  150. // the minimum temperature your thermistor can read. The lower the better/safer.
  151. // This shouldn't need to be more than 30 seconds (30000)
  152. //#define MILLISECONDS_PREHEAT_TIME 0
  153. // @section extruder
  154. // Extruder runout prevention.
  155. // If the machine is idle and the temperature over MINTEMP
  156. // then extrude some filament every couple of SECONDS.
  157. //#define EXTRUDER_RUNOUT_PREVENT
  158. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  159. #define EXTRUDER_RUNOUT_MINTEMP 190
  160. #define EXTRUDER_RUNOUT_SECONDS 30
  161. #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
  162. #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
  163. #endif
  164. // @section temperature
  165. //These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
  166. //The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
  167. #define TEMP_SENSOR_AD595_OFFSET 0.0
  168. #define TEMP_SENSOR_AD595_GAIN 1.0
  169. /**
  170. * Controller Fan
  171. * To cool down the stepper drivers and MOSFETs.
  172. *
  173. * The fan will turn on automatically whenever any stepper is enabled
  174. * and turn off after a set period after all steppers are turned off.
  175. */
  176. //#define USE_CONTROLLER_FAN
  177. #if ENABLED(USE_CONTROLLER_FAN)
  178. //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
  179. #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
  180. #define CONTROLLERFAN_SPEED 255 // 255 == full speed
  181. #endif
  182. // When first starting the main fan, run it at full speed for the
  183. // given number of milliseconds. This gets the fan spinning reliably
  184. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  185. //#define FAN_KICKSTART_TIME 100
  186. // This defines the minimal speed for the main fan, run in PWM mode
  187. // to enable uncomment and set minimal PWM speed for reliable running (1-255)
  188. // if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
  189. //#define FAN_MIN_PWM 50
  190. // @section extruder
  191. /**
  192. * Extruder cooling fans
  193. *
  194. * Extruder auto fans automatically turn on when their extruders'
  195. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  196. *
  197. * Your board's pins file specifies the recommended pins. Override those here
  198. * or set to -1 to disable completely.
  199. *
  200. * Multiple extruders can be assigned to the same pin in which case
  201. * the fan will turn on when any selected extruder is above the threshold.
  202. */
  203. #define E0_AUTO_FAN_PIN -1
  204. #define E1_AUTO_FAN_PIN -1
  205. #define E2_AUTO_FAN_PIN -1
  206. #define E3_AUTO_FAN_PIN -1
  207. #define E4_AUTO_FAN_PIN -1
  208. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  209. #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
  210. /**
  211. * Part-Cooling Fan Multiplexer
  212. *
  213. * This feature allows you to digitally multiplex the fan output.
  214. * The multiplexer is automatically switched at tool-change.
  215. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  216. */
  217. #define FANMUX0_PIN -1
  218. #define FANMUX1_PIN -1
  219. #define FANMUX2_PIN -1
  220. /**
  221. * M355 Case Light on-off / brightness
  222. */
  223. //#define CASE_LIGHT_ENABLE
  224. #if ENABLED(CASE_LIGHT_ENABLE)
  225. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  226. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  227. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  228. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  229. //#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
  230. //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED.
  231. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
  232. #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
  233. #endif
  234. #endif
  235. //===========================================================================
  236. //============================ Mechanical Settings ==========================
  237. //===========================================================================
  238. // @section homing
  239. // If you want endstops to stay on (by default) even when not homing
  240. // enable this option. Override at any time with M120, M121.
  241. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  242. // @section extras
  243. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  244. /**
  245. * Dual Steppers / Dual Endstops
  246. *
  247. * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes.
  248. *
  249. * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to
  250. * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop
  251. * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug
  252. * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'.
  253. *
  254. * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors
  255. * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error
  256. * in X2. Dual endstop offsets can be set at runtime with 'M666 X<offset> Y<offset> Z<offset>'.
  257. */
  258. //#define X_DUAL_STEPPER_DRIVERS
  259. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  260. #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions
  261. //#define X_DUAL_ENDSTOPS
  262. #if ENABLED(X_DUAL_ENDSTOPS)
  263. #define X2_USE_ENDSTOP _XMAX_
  264. #define X_DUAL_ENDSTOPS_ADJUSTMENT 0
  265. #endif
  266. #endif
  267. //#define Y_DUAL_STEPPER_DRIVERS
  268. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  269. #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions
  270. //#define Y_DUAL_ENDSTOPS
  271. #if ENABLED(Y_DUAL_ENDSTOPS)
  272. #define Y2_USE_ENDSTOP _YMAX_
  273. #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0
  274. #endif
  275. #endif
  276. //#define Z_DUAL_STEPPER_DRIVERS
  277. #if ENABLED(Z_DUAL_STEPPER_DRIVERS)
  278. //#define Z_DUAL_ENDSTOPS
  279. #if ENABLED(Z_DUAL_ENDSTOPS)
  280. #define Z2_USE_ENDSTOP _XMAX_
  281. #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0
  282. #endif
  283. #endif
  284. // Enable this for dual x-carriage printers.
  285. // A dual x-carriage design has the advantage that the inactive extruder can be parked which
  286. // prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
  287. // allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
  288. //#define DUAL_X_CARRIAGE
  289. #if ENABLED(DUAL_X_CARRIAGE)
  290. // Configuration for second X-carriage
  291. // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
  292. // the second x-carriage always homes to the maximum endstop.
  293. #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
  294. #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
  295. #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
  296. #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
  297. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  298. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  299. // without modifying the firmware (through the "M218 T1 X???" command).
  300. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  301. // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
  302. // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
  303. // as long as it supports dual x-carriages. (M605 S0)
  304. // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
  305. // that additional slicer support is not required. (M605 S1)
  306. // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
  307. // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
  308. // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
  309. // This is the default power-up mode which can be later using M605.
  310. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
  311. // Default settings in "Auto-park Mode"
  312. #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
  313. #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
  314. // Default x offset in duplication mode (typically set to half print bed width)
  315. #define DEFAULT_DUPLICATION_X_OFFSET 100
  316. #endif // DUAL_X_CARRIAGE
  317. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  318. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  319. //#define EXT_SOLENOID
  320. // @section homing
  321. // Homing hits each endstop, retracts by these distances, then does a slower bump.
  322. #define X_HOME_BUMP_MM 5
  323. #define Y_HOME_BUMP_MM 5
  324. #define Z_HOME_BUMP_MM 2
  325. #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  326. //#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
  327. // When G28 is called, this option will make Y home before X
  328. //#define HOME_Y_BEFORE_X
  329. // Enable this if X or Y can't home without homing the other axis first.
  330. //#define CODEPENDENT_XY_HOMING
  331. // @section machine
  332. #define AXIS_RELATIVE_MODES {false, false, false, false}
  333. // Allow duplication mode with a basic dual-nozzle extruder
  334. //#define DUAL_NOZZLE_DUPLICATION_MODE
  335. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  336. #define INVERT_X_STEP_PIN false
  337. #define INVERT_Y_STEP_PIN false
  338. #define INVERT_Z_STEP_PIN false
  339. #define INVERT_E_STEP_PIN false
  340. // Default stepper release if idle. Set to 0 to deactivate.
  341. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
  342. // Time can be set by M18 and M84.
  343. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  344. #define DISABLE_INACTIVE_X true
  345. #define DISABLE_INACTIVE_Y true
  346. #define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
  347. #define DISABLE_INACTIVE_E true
  348. #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
  349. #define DEFAULT_MINTRAVELFEEDRATE 0.0
  350. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
  351. // @section lcd
  352. #if ENABLED(ULTIPANEL)
  353. #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
  354. #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
  355. #endif
  356. // @section extras
  357. // minimum time in microseconds that a movement needs to take if the buffer is emptied.
  358. #define DEFAULT_MINSEGMENTTIME 20000
  359. // If defined the movements slow down when the look ahead buffer is only half full
  360. #define SLOWDOWN
  361. // Frequency limit
  362. // See nophead's blog for more info
  363. // Not working O
  364. //#define XY_FREQUENCY_LIMIT 15
  365. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  366. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  367. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  368. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
  369. // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
  370. #define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
  371. /**
  372. * @section stepper motor current
  373. *
  374. * Some boards have a means of setting the stepper motor current via firmware.
  375. *
  376. * The power on motor currents are set by:
  377. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  378. * known compatible chips: A4982
  379. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  380. * known compatible chips: AD5206
  381. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  382. * known compatible chips: MCP4728
  383. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
  384. * known compatible chips: MCP4451, MCP4018
  385. *
  386. * Motor currents can also be set by M907 - M910 and by the LCD.
  387. * M907 - applies to all.
  388. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  389. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  390. */
  391. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  392. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  393. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  394. // Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro)
  395. //#define DIGIPOT_I2C
  396. #if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A)
  397. /**
  398. * Common slave addresses:
  399. *
  400. * A (A shifted) B (B shifted) IC
  401. * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
  402. * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
  403. * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
  404. */
  405. #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT
  406. #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT
  407. #endif
  408. //#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
  409. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
  410. // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
  411. // These correspond to the physical drivers, so be mindful if the order is changed.
  412. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  413. //===========================================================================
  414. //=============================Additional Features===========================
  415. //===========================================================================
  416. #define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
  417. #define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
  418. #define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
  419. //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  420. #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
  421. // @section lcd
  422. // Include a page of printer information in the LCD Main Menu
  423. //#define LCD_INFO_MENU
  424. // Leave out seldom-used LCD menu items to recover some Program Memory
  425. //#define SLIM_LCD_MENUS
  426. // Scroll a longer status message into view
  427. //#define STATUS_MESSAGE_SCROLLING
  428. // On the Info Screen, display XY with one decimal place when possible
  429. //#define LCD_DECIMAL_SMALL_XY
  430. // The timeout (in ms) to return to the status screen from sub-menus
  431. //#define LCD_TIMEOUT_TO_STATUS 15000
  432. // Add an 'M73' G-code to set the current percentage
  433. //#define LCD_SET_PROGRESS_MANUALLY
  434. #if ENABLED(SDSUPPORT) || ENABLED(LCD_SET_PROGRESS_MANUALLY)
  435. //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
  436. #if ENABLED(LCD_PROGRESS_BAR)
  437. #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
  438. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
  439. #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
  440. //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
  441. //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
  442. #endif
  443. #endif // SDSUPPORT || LCD_SET_PROGRESS_MANUALLY
  444. /**
  445. * LED Control Menu
  446. * Enable this feature to add LED Control to the LCD menu
  447. */
  448. //#define LED_CONTROL_MENU
  449. #if ENABLED(LED_CONTROL_MENU)
  450. #define LED_COLOR_PRESETS // Enable the Preset Color menu option
  451. #if ENABLED(LED_COLOR_PRESETS)
  452. #define LED_USER_PRESET_RED 255 // User defined RED value
  453. #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
  454. #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
  455. #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
  456. #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  457. //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
  458. #endif
  459. #endif // LED_CONTROL_MENU
  460. #if ENABLED(SDSUPPORT)
  461. // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
  462. // around this by connecting a push button or single throw switch to the pin defined
  463. // as SD_DETECT_PIN in your board's pins definitions.
  464. // This setting should be disabled unless you are using a push button, pulling the pin to ground.
  465. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
  466. #define SD_DETECT_INVERTED
  467. #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
  468. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
  469. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
  470. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
  471. #define SDCARD_RATHERRECENTFIRST
  472. // Add an option in the menu to run all auto#.g files
  473. //#define MENU_ADDAUTOSTART
  474. /**
  475. * Sort SD file listings in alphabetical order.
  476. *
  477. * With this option enabled, items on SD cards will be sorted
  478. * by name for easier navigation.
  479. *
  480. * By default...
  481. *
  482. * - Use the slowest -but safest- method for sorting.
  483. * - Folders are sorted to the top.
  484. * - The sort key is statically allocated.
  485. * - No added G-code (M34) support.
  486. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  487. *
  488. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  489. * compiler to calculate the worst-case usage and throw an error if the SRAM
  490. * limit is exceeded.
  491. *
  492. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  493. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  494. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  495. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  496. */
  497. //#define SDCARD_SORT_ALPHA
  498. // SD Card Sorting options
  499. #if ENABLED(SDCARD_SORT_ALPHA)
  500. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  501. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  502. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
  503. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  504. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  505. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  506. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  507. #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
  508. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
  509. #endif
  510. // This allows hosts to request long names for files and folders with M33
  511. //#define LONG_FILENAME_HOST_SUPPORT
  512. // Enable this option to scroll long filenames in the SD card menu
  513. //#define SCROLL_LONG_FILENAMES
  514. /**
  515. * This option allows you to abort SD printing when any endstop is triggered.
  516. * This feature must be enabled with "M540 S1" or from the LCD menu.
  517. * To have any effect, endstops must be enabled during SD printing.
  518. */
  519. //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
  520. /**
  521. * This option makes it easier to print the same SD Card file again.
  522. * On print completion the LCD Menu will open with the file selected.
  523. * You can just click to start the print, or navigate elsewhere.
  524. */
  525. //#define SD_REPRINT_LAST_SELECTED_FILE
  526. /**
  527. * Auto-report SdCard status with M27 S<seconds>
  528. */
  529. //#define AUTO_REPORT_SD_STATUS
  530. #endif // SDSUPPORT
  531. /**
  532. * Additional options for Graphical Displays
  533. *
  534. * Use the optimizations here to improve printing performance,
  535. * which can be adversely affected by graphical display drawing,
  536. * especially when doing several short moves, and when printing
  537. * on DELTA and SCARA machines.
  538. *
  539. * Some of these options may result in the display lagging behind
  540. * controller events, as there is a trade-off between reliable
  541. * printing performance versus fast display updates.
  542. */
  543. #if ENABLED(DOGLCD)
  544. // Show SD percentage next to the progress bar
  545. //#define DOGM_SD_PERCENT
  546. // Enable to save many cycles by drawing a hollow frame on the Info Screen
  547. #define XYZ_HOLLOW_FRAME
  548. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  549. #define MENU_HOLLOW_FRAME
  550. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  551. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  552. //#define USE_BIG_EDIT_FONT
  553. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
  554. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  555. //#define USE_SMALL_INFOFONT
  556. // Enable this option and reduce the value to optimize screen updates.
  557. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  558. //#define DOGM_SPI_DELAY_US 5
  559. // Swap the CW/CCW indicators in the graphics overlay
  560. //#define OVERLAY_GFX_REVERSE
  561. #if ENABLED(U8GLIB_ST7920)
  562. /**
  563. * ST7920-based LCDs can emulate a 16 x 4 character display using
  564. * the ST7920 character-generator for very fast screen updates.
  565. * Enable LIGHTWEIGHT_UI to use this special display mode.
  566. *
  567. * Since LIGHTWEIGHT_UI has limited space, the position and status
  568. * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
  569. * length of time to display the status message before clearing.
  570. */
  571. //#define LIGHTWEIGHT_UI
  572. #if ENABLED(LIGHTWEIGHT_UI)
  573. #define STATUS_EXPIRE_SECONDS 20
  574. #endif
  575. #endif
  576. #endif // DOGLCD
  577. // @section safety
  578. // The hardware watchdog should reset the microcontroller disabling all outputs,
  579. // in case the firmware gets stuck and doesn't do temperature regulation.
  580. #define USE_WATCHDOG
  581. #if ENABLED(USE_WATCHDOG)
  582. // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
  583. // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
  584. // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
  585. //#define WATCHDOG_RESET_MANUAL
  586. #endif
  587. // @section lcd
  588. /**
  589. * Babystepping enables movement of the axes by tiny increments without changing
  590. * the current position values. This feature is used primarily to adjust the Z
  591. * axis in the first layer of a print in real-time.
  592. *
  593. * Warning: Does not respect endstops!
  594. */
  595. //#define BABYSTEPPING
  596. #if ENABLED(BABYSTEPPING)
  597. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  598. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  599. #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
  600. //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
  601. //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  602. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  603. // Note: Extra time may be added to mitigate controller latency.
  604. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  605. #endif
  606. // @section extruder
  607. /**
  608. * Linear Pressure Control v1.5
  609. *
  610. * Assumption: advance [steps] = k * (delta velocity [steps/s])
  611. * K=0 means advance disabled.
  612. *
  613. * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
  614. *
  615. * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
  616. * Larger K values will be needed for flexible filament and greater distances.
  617. * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
  618. * print acceleration will be reduced during the affected moves to keep within the limit.
  619. *
  620. * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
  621. * Mention @Sebastianv650 on GitHub to alert the author of any issues.
  622. */
  623. //#define LIN_ADVANCE
  624. #if ENABLED(LIN_ADVANCE)
  625. #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
  626. //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
  627. #endif
  628. // @section leveling
  629. #if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
  630. #define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
  631. #elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
  632. #define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
  633. #endif
  634. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
  635. // Override the mesh area if the automatic (max) area is too large
  636. //#define MESH_MIN_X MESH_INSET
  637. //#define MESH_MIN_Y MESH_INSET
  638. //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
  639. //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
  640. #endif
  641. // @section extras
  642. //
  643. // G2/G3 Arc Support
  644. //
  645. #define ARC_SUPPORT // Disable this feature to save ~3226 bytes
  646. #if ENABLED(ARC_SUPPORT)
  647. #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
  648. #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
  649. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  650. //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
  651. #endif
  652. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  653. //#define BEZIER_CURVE_SUPPORT
  654. // G38.2 and G38.3 Probe Target
  655. // Set MULTIPLE_PROBING if you want G38 to double touch
  656. //#define G38_PROBE_TARGET
  657. #if ENABLED(G38_PROBE_TARGET)
  658. #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
  659. #endif
  660. // Moves (or segments) with fewer steps than this will be joined with the next move
  661. #define MIN_STEPS_PER_SEGMENT 6
  662. // The minimum pulse width (in µs) for stepping a stepper.
  663. // Set this if you find stepping unreliable, or if using a very fast CPU.
  664. // 0 is OK for AVR, 0 is OK for A4989 drivers, 2 is needed for DRV8825 drivers
  665. #define MINIMUM_STEPPER_PULSE 2 // (µs) DRV8825 on 32bit CPUs
  666. // @section temperature
  667. // Control heater 0 and heater 1 in parallel.
  668. //#define HEATERS_PARALLEL
  669. //===========================================================================
  670. //================================= Buffers =================================
  671. //===========================================================================
  672. // @section hidden
  673. // The number of linear motions that can be in the plan at any give time.
  674. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
  675. #if ENABLED(SDSUPPORT)
  676. #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
  677. #else
  678. #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
  679. #endif
  680. // @section serial
  681. // The ASCII buffer for serial input
  682. #define MAX_CMD_SIZE 96
  683. #define BUFSIZE 4
  684. // Transmission to Host Buffer Size
  685. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  686. // To buffer a simple "ok" you need 4 bytes.
  687. // For ADVANCED_OK (M105) you need 32 bytes.
  688. // For debug-echo: 128 bytes for the optimal speed.
  689. // Other output doesn't need to be that speedy.
  690. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  691. #define TX_BUFFER_SIZE 0
  692. // Host Receive Buffer Size
  693. // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
  694. // To use flow control, set this buffer size to at least 1024 bytes.
  695. // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
  696. //#define RX_BUFFER_SIZE 1024
  697. #if RX_BUFFER_SIZE >= 1024
  698. // Enable to have the controller send XON/XOFF control characters to
  699. // the host to signal the RX buffer is becoming full.
  700. //#define SERIAL_XON_XOFF
  701. #endif
  702. #if ENABLED(SDSUPPORT)
  703. // Enable this option to collect and display the maximum
  704. // RX queue usage after transferring a file to SD.
  705. //#define SERIAL_STATS_MAX_RX_QUEUED
  706. // Enable this option to collect and display the number
  707. // of dropped bytes after a file transfer to SD.
  708. //#define SERIAL_STATS_DROPPED_RX
  709. #endif
  710. // Enable an emergency-command parser to intercept certain commands as they
  711. // enter the serial receive buffer, so they cannot be blocked.
  712. // Currently handles M108, M112, M410
  713. // Does not work on boards using AT90USB (USBCON) processors!
  714. //#define EMERGENCY_PARSER
  715. // Bad Serial-connections can miss a received command by sending an 'ok'
  716. // Therefore some clients abort after 30 seconds in a timeout.
  717. // Some other clients start sending commands while receiving a 'wait'.
  718. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  719. //#define NO_TIMEOUTS 1000 // Milliseconds
  720. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  721. //#define ADVANCED_OK
  722. // @section extras
  723. /**
  724. * Firmware-based and LCD-controlled retract
  725. *
  726. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  727. * Use M207 and M208 to define parameters for retract / recover.
  728. *
  729. * Use M209 to enable or disable auto-retract.
  730. * With auto-retract enabled, all G1 E moves within the set range
  731. * will be converted to firmware-based retract/recover moves.
  732. *
  733. * Note: Be sure to turn off auto-retract during filament change.
  734. * Note: Current status (Retract / Swap / Zlift) isn't reset by G28.
  735. *
  736. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  737. *
  738. */
  739. //#define FWRETRACT // ONLY PARTIALLY TESTED
  740. #if ENABLED(FWRETRACT)
  741. #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
  742. #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
  743. #define RETRACT_LENGTH 3 // Default retract length (positive mm)
  744. #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
  745. #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)
  746. #define RETRACT_ZLIFT 0 // Default retract Z-lift
  747. #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering)
  748. #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
  749. #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s)
  750. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s)
  751. #endif
  752. /**
  753. * Extra Fan Speed
  754. * Adds a secondary fan speed for each print-cooling fan.
  755. * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
  756. * 'M106 P<fan> T2' : Use the set secondary speed
  757. * 'M106 P<fan> T1' : Restore the previous fan speed
  758. */
  759. //#define EXTRA_FAN_SPEED
  760. /**
  761. * Advanced Pause
  762. * Experimental feature for filament change support and for parking the nozzle when paused.
  763. * Adds the GCode M600 for initiating filament change.
  764. * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
  765. *
  766. * Requires an LCD display.
  767. * Requires NOZZLE_PARK_FEATURE.
  768. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  769. */
  770. //#define ADVANCED_PAUSE_FEATURE
  771. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  772. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
  773. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
  774. // This short retract is done immediately, before parking the nozzle.
  775. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
  776. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
  777. // For Bowden, the full length of the tube and nozzle.
  778. // For direct drive, the full length of the nozzle.
  779. // Set to 0 for manual unloading.
  780. #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
  781. #define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
  782. // For Bowden, the full length of the tube and nozzle.
  783. // For direct drive, the full length of the nozzle.
  784. #define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  785. #define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
  786. // Set to 0 for manual extrusion.
  787. // Filament can be extruded repeatedly from the Filament Change menu
  788. // until extrusion is consistent, and to purge old filament.
  789. // Filament Unload does a Retract, Delay, and Purge first:
  790. #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
  791. #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
  792. #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
  793. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
  794. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
  795. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
  796. //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
  797. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
  798. //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  799. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
  800. #endif
  801. // @section tmc
  802. /**
  803. * Enable this section if you have TMC26X motor drivers.
  804. * You will need to import the TMC26XStepper library into the Arduino IDE for this
  805. * (https://github.com/trinamic/TMC26XStepper.git)
  806. */
  807. //#define HAVE_TMCDRIVER
  808. #if ENABLED(HAVE_TMCDRIVER)
  809. //#define X_IS_TMC
  810. //#define X2_IS_TMC
  811. //#define Y_IS_TMC
  812. //#define Y2_IS_TMC
  813. //#define Z_IS_TMC
  814. //#define Z2_IS_TMC
  815. //#define E0_IS_TMC
  816. //#define E1_IS_TMC
  817. //#define E2_IS_TMC
  818. //#define E3_IS_TMC
  819. //#define E4_IS_TMC
  820. #define X_MAX_CURRENT 1000 // in mA
  821. #define X_SENSE_RESISTOR 91 // in mOhms
  822. #define X_MICROSTEPS 16 // number of microsteps
  823. #define X2_MAX_CURRENT 1000
  824. #define X2_SENSE_RESISTOR 91
  825. #define X2_MICROSTEPS 16
  826. #define Y_MAX_CURRENT 1000
  827. #define Y_SENSE_RESISTOR 91
  828. #define Y_MICROSTEPS 16
  829. #define Y2_MAX_CURRENT 1000
  830. #define Y2_SENSE_RESISTOR 91
  831. #define Y2_MICROSTEPS 16
  832. #define Z_MAX_CURRENT 1000
  833. #define Z_SENSE_RESISTOR 91
  834. #define Z_MICROSTEPS 16
  835. #define Z2_MAX_CURRENT 1000
  836. #define Z2_SENSE_RESISTOR 91
  837. #define Z2_MICROSTEPS 16
  838. #define E0_MAX_CURRENT 1000
  839. #define E0_SENSE_RESISTOR 91
  840. #define E0_MICROSTEPS 16
  841. #define E1_MAX_CURRENT 1000
  842. #define E1_SENSE_RESISTOR 91
  843. #define E1_MICROSTEPS 16
  844. #define E2_MAX_CURRENT 1000
  845. #define E2_SENSE_RESISTOR 91
  846. #define E2_MICROSTEPS 16
  847. #define E3_MAX_CURRENT 1000
  848. #define E3_SENSE_RESISTOR 91
  849. #define E3_MICROSTEPS 16
  850. #define E4_MAX_CURRENT 1000
  851. #define E4_SENSE_RESISTOR 91
  852. #define E4_MICROSTEPS 16
  853. #endif
  854. // @section TMC2130, TMC2208
  855. /**
  856. * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
  857. *
  858. * You'll also need the TMC2130Stepper Arduino library
  859. * (https://github.com/teemuatlut/TMC2130Stepper).
  860. *
  861. * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
  862. * the hardware SPI interface on your board and define the required CS pins
  863. * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  864. * You may also use software SPI if you wish to use general purpose IO pins.
  865. */
  866. //#define HAVE_TMC2130
  867. /**
  868. * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
  869. * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
  870. * To use the reading capabilities, also connect #_SERIAL_RX_PIN
  871. * to PDN_UART without a resistor.
  872. * The drivers can also be used with hardware serial.
  873. *
  874. * You'll also need the TMC2208Stepper Arduino library
  875. * (https://github.com/teemuatlut/TMC2208Stepper).
  876. */
  877. //#define HAVE_TMC2208
  878. #if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
  879. // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
  880. //#define X_IS_TMC2130
  881. //#define X2_IS_TMC2130
  882. //#define Y_IS_TMC2130
  883. //#define Y2_IS_TMC2130
  884. //#define Z_IS_TMC2130
  885. //#define Z2_IS_TMC2130
  886. //#define E0_IS_TMC2130
  887. //#define E1_IS_TMC2130
  888. //#define E2_IS_TMC2130
  889. //#define E3_IS_TMC2130
  890. //#define E4_IS_TMC2130
  891. //#define X_IS_TMC2208
  892. //#define X2_IS_TMC2208
  893. //#define Y_IS_TMC2208
  894. //#define Y2_IS_TMC2208
  895. //#define Z_IS_TMC2208
  896. //#define Z2_IS_TMC2208
  897. //#define E0_IS_TMC2208
  898. //#define E1_IS_TMC2208
  899. //#define E2_IS_TMC2208
  900. //#define E3_IS_TMC2208
  901. //#define E4_IS_TMC2208
  902. /**
  903. * Stepper driver settings
  904. */
  905. #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
  906. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  907. #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256
  908. #define X_CURRENT 800 // rms current in mA. Multiply by 1.41 for peak current.
  909. #define X_MICROSTEPS 16 // 0..256
  910. #define Y_CURRENT 800
  911. #define Y_MICROSTEPS 16
  912. #define Z_CURRENT 800
  913. #define Z_MICROSTEPS 16
  914. #define X2_CURRENT 800
  915. #define X2_MICROSTEPS 16
  916. #define Y2_CURRENT 800
  917. #define Y2_MICROSTEPS 16
  918. #define Z2_CURRENT 800
  919. #define Z2_MICROSTEPS 16
  920. #define E0_CURRENT 800
  921. #define E0_MICROSTEPS 16
  922. #define E1_CURRENT 800
  923. #define E1_MICROSTEPS 16
  924. #define E2_CURRENT 800
  925. #define E2_MICROSTEPS 16
  926. #define E3_CURRENT 800
  927. #define E3_MICROSTEPS 16
  928. #define E4_CURRENT 800
  929. #define E4_MICROSTEPS 16
  930. /**
  931. * Use software SPI for TMC2130.
  932. * The default SW SPI pins are defined the respective pins files,
  933. * but you can override or define them here.
  934. */
  935. //#define TMC_USE_SW_SPI
  936. //#define TMC_SW_MOSI -1
  937. //#define TMC_SW_MISO -1
  938. //#define TMC_SW_SCK -1
  939. /**
  940. * Use Trinamic's ultra quiet stepping mode.
  941. * When disabled, Marlin will use spreadCycle stepping mode.
  942. */
  943. #define STEALTHCHOP
  944. /**
  945. * Monitor Trinamic TMC2130 and TMC2208 drivers for error conditions,
  946. * like overtemperature and short to ground. TMC2208 requires hardware serial.
  947. * In the case of overtemperature Marlin can decrease the driver current until error condition clears.
  948. * Other detected conditions can be used to stop the current print.
  949. * Relevant g-codes:
  950. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  951. * M911 - Report stepper driver overtemperature pre-warn condition.
  952. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  953. * M122 S0/1 - Report driver parameters (Requires TMC_DEBUG)
  954. */
  955. //#define MONITOR_DRIVER_STATUS
  956. #if ENABLED(MONITOR_DRIVER_STATUS)
  957. #define CURRENT_STEP_DOWN 50 // [mA]
  958. #define REPORT_CURRENT_CHANGE
  959. #define STOP_ON_ERROR
  960. #endif
  961. /**
  962. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  963. * This mode allows for faster movements at the expense of higher noise levels.
  964. * STEALTHCHOP needs to be enabled.
  965. * M913 X/Y/Z/E to live tune the setting
  966. */
  967. //#define HYBRID_THRESHOLD
  968. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  969. #define X2_HYBRID_THRESHOLD 100
  970. #define Y_HYBRID_THRESHOLD 100
  971. #define Y2_HYBRID_THRESHOLD 100
  972. #define Z_HYBRID_THRESHOLD 3
  973. #define Z2_HYBRID_THRESHOLD 3
  974. #define E0_HYBRID_THRESHOLD 30
  975. #define E1_HYBRID_THRESHOLD 30
  976. #define E2_HYBRID_THRESHOLD 30
  977. #define E3_HYBRID_THRESHOLD 30
  978. #define E4_HYBRID_THRESHOLD 30
  979. /**
  980. * Use stallGuard2 to sense an obstacle and trigger an endstop.
  981. * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
  982. * X, Y, and Z homing will always be done in spreadCycle mode.
  983. *
  984. * X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
  985. * Higher values make the system LESS sensitive.
  986. * Lower value make the system MORE sensitive.
  987. * Too low values can lead to false positives, while too high values will collide the axis without triggering.
  988. * It is advised to set X/Y/Z_HOME_BUMP_MM to 0.
  989. * M914 X/Y/Z to live tune the setting
  990. */
  991. //#define SENSORLESS_HOMING // TMC2130 only
  992. #if ENABLED(SENSORLESS_HOMING)
  993. #define X_HOMING_SENSITIVITY 8
  994. #define Y_HOMING_SENSITIVITY 8
  995. #define Z_HOMING_SENSITIVITY 8
  996. #endif
  997. /**
  998. * Enable M122 debugging command for TMC stepper drivers.
  999. * M122 S0/1 will enable continous reporting.
  1000. */
  1001. //#define TMC_DEBUG
  1002. /**
  1003. * M915 Z Axis Calibration
  1004. *
  1005. * - Adjust Z stepper current,
  1006. * - Drive the Z axis to its physical maximum, and
  1007. * - Home Z to account for the lost steps.
  1008. *
  1009. * Use M915 Snn to specify the current.
  1010. * Use M925 Znn to add extra Z height to Z_MAX_POS.
  1011. */
  1012. //#define TMC_Z_CALIBRATION
  1013. #if ENABLED(TMC_Z_CALIBRATION)
  1014. #define CALIBRATION_CURRENT 250
  1015. #define CALIBRATION_EXTRA_HEIGHT 10
  1016. #endif
  1017. /**
  1018. * You can set your own advanced settings by filling in predefined functions.
  1019. * A list of available functions can be found on the library github page
  1020. * https://github.com/teemuatlut/TMC2130Stepper
  1021. * https://github.com/teemuatlut/TMC2208Stepper
  1022. *
  1023. * Example:
  1024. * #define TMC_ADV() { \
  1025. * stepperX.diag0_temp_prewarn(1); \
  1026. * stepperY.interpolate(0); \
  1027. * }
  1028. */
  1029. #define TMC_ADV() { }
  1030. #endif // TMC2130 || TMC2208
  1031. // @section L6470
  1032. /**
  1033. * Enable this section if you have L6470 motor drivers.
  1034. * You need to import the L6470 library into the Arduino IDE for this.
  1035. * (https://github.com/ameyer/Arduino-L6470)
  1036. */
  1037. //#define HAVE_L6470DRIVER
  1038. #if ENABLED(HAVE_L6470DRIVER)
  1039. //#define X_IS_L6470
  1040. //#define X2_IS_L6470
  1041. //#define Y_IS_L6470
  1042. //#define Y2_IS_L6470
  1043. //#define Z_IS_L6470
  1044. //#define Z2_IS_L6470
  1045. //#define E0_IS_L6470
  1046. //#define E1_IS_L6470
  1047. //#define E2_IS_L6470
  1048. //#define E3_IS_L6470
  1049. //#define E4_IS_L6470
  1050. #define X_MICROSTEPS 16 // number of microsteps
  1051. #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
  1052. #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
  1053. #define X2_MICROSTEPS 16
  1054. #define X2_OVERCURRENT 2000
  1055. #define X2_STALLCURRENT 1500
  1056. #define Y_MICROSTEPS 16
  1057. #define Y_OVERCURRENT 2000
  1058. #define Y_STALLCURRENT 1500
  1059. #define Y2_MICROSTEPS 16
  1060. #define Y2_OVERCURRENT 2000
  1061. #define Y2_STALLCURRENT 1500
  1062. #define Z_MICROSTEPS 16
  1063. #define Z_OVERCURRENT 2000
  1064. #define Z_STALLCURRENT 1500
  1065. #define Z2_MICROSTEPS 16
  1066. #define Z2_OVERCURRENT 2000
  1067. #define Z2_STALLCURRENT 1500
  1068. #define E0_MICROSTEPS 16
  1069. #define E0_OVERCURRENT 2000
  1070. #define E0_STALLCURRENT 1500
  1071. #define E1_MICROSTEPS 16
  1072. #define E1_OVERCURRENT 2000
  1073. #define E1_STALLCURRENT 1500
  1074. #define E2_MICROSTEPS 16
  1075. #define E2_OVERCURRENT 2000
  1076. #define E2_STALLCURRENT 1500
  1077. #define E3_MICROSTEPS 16
  1078. #define E3_OVERCURRENT 2000
  1079. #define E3_STALLCURRENT 1500
  1080. #define E4_MICROSTEPS 16
  1081. #define E4_OVERCURRENT 2000
  1082. #define E4_STALLCURRENT 1500
  1083. #endif
  1084. /**
  1085. * TWI/I2C BUS
  1086. *
  1087. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  1088. * machines. Enabling this will allow you to send and receive I2C data from slave
  1089. * devices on the bus.
  1090. *
  1091. * ; Example #1
  1092. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  1093. * ; It uses multiple M260 commands with one B<base 10> arg
  1094. * M260 A99 ; Target slave address
  1095. * M260 B77 ; M
  1096. * M260 B97 ; a
  1097. * M260 B114 ; r
  1098. * M260 B108 ; l
  1099. * M260 B105 ; i
  1100. * M260 B110 ; n
  1101. * M260 S1 ; Send the current buffer
  1102. *
  1103. * ; Example #2
  1104. * ; Request 6 bytes from slave device with address 0x63 (99)
  1105. * M261 A99 B5
  1106. *
  1107. * ; Example #3
  1108. * ; Example serial output of a M261 request
  1109. * echo:i2c-reply: from:99 bytes:5 data:hello
  1110. */
  1111. // @section i2cbus
  1112. //#define EXPERIMENTAL_I2CBUS
  1113. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  1114. // @section extras
  1115. /**
  1116. * Spindle & Laser control
  1117. *
  1118. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  1119. * to set spindle speed, spindle direction, and laser power.
  1120. *
  1121. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  1122. * Marlin can be used to turn the spindle on and off. It can also be used to set
  1123. * the spindle speed from 5,000 to 30,000 RPM.
  1124. *
  1125. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  1126. * hardware PWM pin for the speed control and a pin for the rotation direction.
  1127. *
  1128. * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  1129. */
  1130. //#define SPINDLE_LASER_ENABLE
  1131. #if ENABLED(SPINDLE_LASER_ENABLE)
  1132. #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
  1133. #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
  1134. #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
  1135. #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
  1136. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
  1137. #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
  1138. #define SPINDLE_INVERT_DIR false
  1139. #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
  1140. /**
  1141. * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
  1142. *
  1143. * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
  1144. * where PWM duty cycle varies from 0 to 255
  1145. *
  1146. * set the following for your controller (ALL MUST BE SET)
  1147. */
  1148. #define SPEED_POWER_SLOPE 118.4
  1149. #define SPEED_POWER_INTERCEPT 0
  1150. #define SPEED_POWER_MIN 5000
  1151. #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
  1152. //#define SPEED_POWER_SLOPE 0.3922
  1153. //#define SPEED_POWER_INTERCEPT 0
  1154. //#define SPEED_POWER_MIN 10
  1155. //#define SPEED_POWER_MAX 100 // 0-100%
  1156. #endif
  1157. /**
  1158. * Filament Width Sensor
  1159. *
  1160. * Measures the filament width in real-time and adjusts
  1161. * flow rate to compensate for any irregularities.
  1162. *
  1163. * Also allows the measured filament diameter to set the
  1164. * extrusion rate, so the slicer only has to specify the
  1165. * volume.
  1166. *
  1167. * Only a single extruder is supported at this time.
  1168. *
  1169. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  1170. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  1171. * 301 RAMBO : Analog input 3
  1172. *
  1173. * Note: May require analog pins to be defined for other boards.
  1174. */
  1175. //#define FILAMENT_WIDTH_SENSOR
  1176. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  1177. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
  1178. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  1179. #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
  1180. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  1181. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  1182. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  1183. //#define FILAMENT_LCD_DISPLAY
  1184. #endif
  1185. /**
  1186. * CNC Coordinate Systems
  1187. *
  1188. * Enables G53 and G54-G59.3 commands to select coordinate systems
  1189. * and G92.1 to reset the workspace to native machine space.
  1190. */
  1191. //#define CNC_COORDINATE_SYSTEMS
  1192. /**
  1193. * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
  1194. */
  1195. //#define PINS_DEBUGGING
  1196. /**
  1197. * Auto-report temperatures with M155 S<seconds>
  1198. */
  1199. #define AUTO_REPORT_TEMPERATURES
  1200. /**
  1201. * Include capabilities in M115 output
  1202. */
  1203. #define EXTENDED_CAPABILITIES_REPORT
  1204. /**
  1205. * Disable all Volumetric extrusion options
  1206. */
  1207. //#define NO_VOLUMETRICS
  1208. #if DISABLED(NO_VOLUMETRICS)
  1209. /**
  1210. * Volumetric extrusion default state
  1211. * Activate to make volumetric extrusion the default method,
  1212. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  1213. *
  1214. * M200 D0 to disable, M200 Dn to set a new diameter.
  1215. */
  1216. //#define VOLUMETRIC_DEFAULT_ON
  1217. #endif
  1218. /**
  1219. * Enable this option for a leaner build of Marlin that removes all
  1220. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  1221. *
  1222. * - M206 and M428 are disabled.
  1223. * - G92 will revert to its behavior from Marlin 1.0.
  1224. */
  1225. //#define NO_WORKSPACE_OFFSETS
  1226. /**
  1227. * Set the number of proportional font spaces required to fill up a typical character space.
  1228. * This can help to better align the output of commands like `G29 O` Mesh Output.
  1229. *
  1230. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  1231. * Otherwise, adjust according to your client and font.
  1232. */
  1233. #define PROPORTIONAL_FONT_RATIO 1.0
  1234. /**
  1235. * Spend 28 bytes of SRAM to optimize the GCode parser
  1236. */
  1237. #define FASTER_GCODE_PARSER
  1238. /**
  1239. * User-defined menu items that execute custom GCode
  1240. */
  1241. //#define CUSTOM_USER_MENUS
  1242. #if ENABLED(CUSTOM_USER_MENUS)
  1243. #define USER_SCRIPT_DONE "M117 User Script Done"
  1244. #define USER_SCRIPT_AUDIBLE_FEEDBACK
  1245. //#define USER_SCRIPT_RETURN // Return to status screen after a script
  1246. #define USER_DESC_1 "Home & UBL Info"
  1247. #define USER_GCODE_1 "G28\nG29 W"
  1248. #define USER_DESC_2 "Preheat for PLA"
  1249. #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  1250. #define USER_DESC_3 "Preheat for ABS"
  1251. #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  1252. #define USER_DESC_4 "Heat Bed/Home/Level"
  1253. #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  1254. #define USER_DESC_5 "Home & Info"
  1255. #define USER_GCODE_5 "G28\nM503"
  1256. #endif
  1257. /**
  1258. * Specify an action command to send to the host when the printer is killed.
  1259. * Will be sent in the form '//action:ACTION_ON_KILL', e.g. '//action:poweroff'.
  1260. * The host must be configured to handle the action command.
  1261. */
  1262. //#define ACTION_ON_KILL "poweroff"
  1263. /**
  1264. * Specify an action command to send to the host on pause and resume.
  1265. * Will be sent in the form '//action:ACTION_ON_PAUSE', e.g. '//action:pause'.
  1266. * The host must be configured to handle the action command.
  1267. */
  1268. //#define ACTION_ON_PAUSE "pause"
  1269. //#define ACTION_ON_RESUME "resume"
  1270. //===========================================================================
  1271. //====================== I2C Position Encoder Settings ======================
  1272. //===========================================================================
  1273. /**
  1274. * I2C position encoders for closed loop control.
  1275. * Developed by Chris Barr at Aus3D.
  1276. *
  1277. * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
  1278. * Github: https://github.com/Aus3D/MagneticEncoder
  1279. *
  1280. * Supplier: http://aus3d.com.au/magnetic-encoder-module
  1281. * Alternative Supplier: http://reliabuild3d.com/
  1282. *
  1283. * Reilabuild encoders have been modified to improve reliability.
  1284. */
  1285. //#define I2C_POSITION_ENCODERS
  1286. #if ENABLED(I2C_POSITION_ENCODERS)
  1287. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  1288. // encoders supported currently.
  1289. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  1290. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  1291. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  1292. // I2CPE_ENC_TYPE_ROTARY.
  1293. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  1294. // 1mm poles. For linear encoders this is ticks / mm,
  1295. // for rotary encoders this is ticks / revolution.
  1296. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  1297. // steps per full revolution (motor steps/rev * microstepping)
  1298. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  1299. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
  1300. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  1301. // printer will attempt to correct the error; errors
  1302. // smaller than this are ignored to minimize effects of
  1303. // measurement noise / latency (filter).
  1304. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  1305. #define I2CPE_ENC_2_AXIS Y_AXIS
  1306. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  1307. #define I2CPE_ENC_2_TICKS_UNIT 2048
  1308. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  1309. //#define I2CPE_ENC_2_INVERT
  1310. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
  1311. #define I2CPE_ENC_2_EC_THRESH 0.10
  1312. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  1313. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  1314. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  1315. #define I2CPE_ENC_4_AXIS E_AXIS
  1316. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  1317. #define I2CPE_ENC_5_AXIS E_AXIS
  1318. // Default settings for encoders which are enabled, but without settings configured above.
  1319. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  1320. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  1321. #define I2CPE_DEF_TICKS_REV (16 * 200)
  1322. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  1323. #define I2CPE_DEF_EC_THRESH 0.1
  1324. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  1325. // axis after which the printer will abort. Comment out to
  1326. // disable abort behaviour.
  1327. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  1328. // for this amount of time (in ms) before the encoder
  1329. // is trusted again.
  1330. /**
  1331. * Position is checked every time a new command is executed from the buffer but during long moves,
  1332. * this setting determines the minimum update time between checks. A value of 100 works well with
  1333. * error rolling average when attempting to correct only for skips and not for vibration.
  1334. */
  1335. #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
  1336. // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
  1337. #define I2CPE_ERR_ROLLING_AVERAGE
  1338. #endif // I2C_POSITION_ENCODERS
  1339. /**
  1340. * MAX7219 Debug Matrix
  1341. *
  1342. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip, which can be used as a status
  1343. * display. Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  1344. *
  1345. * Fully assembled MAX7219 boards can be found on the internet for under $2(US).
  1346. * For example, see https://www.ebay.com/sch/i.html?_nkw=332349290049
  1347. */
  1348. //#define MAX7219_DEBUG
  1349. #if ENABLED(MAX7219_DEBUG)
  1350. #define MAX7219_CLK_PIN 64 // 77 on Re-ARM // Configuration of the 3 pins to control the display
  1351. #define MAX7219_DIN_PIN 57 // 78 on Re-ARM
  1352. #define MAX7219_LOAD_PIN 44 // 79 on Re-ARM
  1353. /**
  1354. * Sample debug features
  1355. * If you add more debug displays, be careful to avoid conflicts!
  1356. */
  1357. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  1358. #define MAX7219_DEBUG_STEPPER_HEAD 3 // Show the stepper queue head position on this and the next LED matrix row
  1359. #define MAX7219_DEBUG_STEPPER_TAIL 5 // Show the stepper queue tail position on this and the next LED matrix row
  1360. #define MAX7219_DEBUG_STEPPER_QUEUE 0 // Show the current stepper queue depth on this and the next LED matrix row
  1361. // If you experience stuttering, reboots, etc. this option can reveal how
  1362. // tweaks made to the configuration are affecting the printer in real-time.
  1363. #endif
  1364. /**
  1365. * NanoDLP Sync support
  1366. *
  1367. * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp"
  1368. * string to enable synchronization with DLP projector exposure. This change will allow to use
  1369. * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  1370. */
  1371. //#define NANODLP_Z_SYNC
  1372. #if ENABLED(NANODLP_Z_SYNC)
  1373. //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
  1374. // Default behaviour is limited to Z axis only.
  1375. #endif
  1376. #endif // CONFIGURATION_ADV_H