| 1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- *
- */
-
- /**
- * Leapfrog Driver board pin assignments
- */
-
- #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
- #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
- #endif
-
- #define X_STEP_PIN 28
- #define X_DIR_PIN 63
- #define X_ENABLE_PIN 29
- #define X_MIN_PIN 47
- #define X_MAX_PIN 2 //Max endstops default to disabled "-1", set to commented value to enable.
-
- #define Y_STEP_PIN 14 // A6
- #define Y_DIR_PIN 15 // A0
- #define Y_ENABLE_PIN 39
- #define Y_MIN_PIN 48
- #define Y_MAX_PIN 15
-
- #define Z_STEP_PIN 31 // A2
- #define Z_DIR_PIN 32 // A6
- #define Z_ENABLE_PIN 30 // A1
- #define Z_MIN_PIN 49
- #define Z_MAX_PIN -1
-
- #define E0_STEP_PIN 34 //34
- #define E0_DIR_PIN 35 //35
- #define E0_ENABLE_PIN 33 //33
-
- #define E1_STEP_PIN 37 //37
- #define E1_DIR_PIN 40 //40
- #define E1_ENABLE_PIN 36 //36
-
- #define SDSS 11
- #define LED_PIN 13
- #define FAN_PIN 7
- #define SOL1_PIN 16
- #define SOL2_PIN 17
-
- #define HEATER_0_PIN 9
- #define HEATER_1_PIN 8 // 12
- #define HEATER_2_PIN 11 //-1 // 13
- #define TEMP_0_PIN 13 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
- #define TEMP_1_PIN 15 // 1
- #define HEATER_BED_PIN 10 // 14/15
- #define TEMP_BED_PIN 14 // 1,2 or I2C
- /* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
|
