My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Nevar pievienot vairāk kā 25 tēmas Tēmai ir jāsākas ar burtu vai ciparu, tā var saturēt domu zīmes ('-') un var būt līdz 35 simboliem gara.

Configuration.h 57KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497149814991500150115021503150415051506150715081509151015111512151315141515151615171518151915201521152215231524152515261527152815291530153115321533153415351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. #define CONFIGURATION_H_VERSION 010100
  40. //===========================================================================
  41. //============================= Getting Started =============================
  42. //===========================================================================
  43. /**
  44. * Here are some standard links for getting your machine calibrated:
  45. *
  46. * http://reprap.org/wiki/Calibration
  47. * http://youtu.be/wAL9d7FgInk
  48. * http://calculator.josefprusa.cz
  49. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  50. * http://www.thingiverse.com/thing:5573
  51. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  52. * http://www.thingiverse.com/thing:298812
  53. */
  54. //===========================================================================
  55. //============================= DELTA Printer ===============================
  56. //===========================================================================
  57. // For a Delta printer replace the configuration files with the files in the
  58. // example_configurations/delta directory.
  59. //
  60. //===========================================================================
  61. //============================= SCARA Printer ===============================
  62. //===========================================================================
  63. // For a Scara printer replace the configuration files with the files in the
  64. // example_configurations/SCARA directory.
  65. //
  66. // @section info
  67. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  68. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  69. // build by the user have been successfully uploaded into firmware.
  70. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  71. #define SHOW_BOOTSCREEN
  72. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  73. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  74. //
  75. // *** VENDORS PLEASE READ *****************************************************
  76. //
  77. // Marlin now allow you to have a vendor boot image to be displayed on machine
  78. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  79. // custom boot image and then the default Marlin boot image is shown.
  80. //
  81. // We suggest for you to take advantage of this new feature and keep the Marlin
  82. // boot image unmodified. For an example have a look at the bq Hephestos 2
  83. // example configuration folder.
  84. //
  85. //#define SHOW_CUSTOM_BOOTSCREEN
  86. // @section machine
  87. /**
  88. * Select which serial port on the board will be used for communication with the host.
  89. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  90. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  91. *
  92. * :[0, 1, 2, 3, 4, 5, 6, 7]
  93. */
  94. #define SERIAL_PORT 0
  95. /**
  96. * This setting determines the communication speed of the printer.
  97. *
  98. * 250000 works in most cases, but you might try a lower speed if
  99. * you commonly experience drop-outs during host printing.
  100. *
  101. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
  102. */
  103. #define BAUDRATE 250000
  104. // Enable the Bluetooth serial interface on AT90USB devices
  105. //#define BLUETOOTH
  106. // The following define selects which electronics board you have.
  107. // Please choose the name from boards.h that matches your setup
  108. #ifndef MOTHERBOARD
  109. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  110. #endif
  111. // Optional custom name for your RepStrap or other custom machine
  112. // Displayed in the LCD "Ready" message
  113. //#define CUSTOM_MACHINE_NAME "3D Printer"
  114. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  115. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  116. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  117. // This defines the number of extruders
  118. // :[1, 2, 3, 4, 5]
  119. #define EXTRUDERS 1
  120. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  121. //#define SINGLENOZZLE
  122. // A dual extruder that uses a single stepper motor
  123. // Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z
  124. //#define SWITCHING_EXTRUDER
  125. #if ENABLED(SWITCHING_EXTRUDER)
  126. #define SWITCHING_EXTRUDER_SERVO_NR 0
  127. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  128. //#define HOTEND_OFFSET_Z {0.0, 0.0}
  129. #endif
  130. /**
  131. * "Mixing Extruder"
  132. * - Adds a new code, M165, to set the current mix factors.
  133. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  134. * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  135. * - This implementation supports only a single extruder.
  136. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  137. */
  138. //#define MIXING_EXTRUDER
  139. #if ENABLED(MIXING_EXTRUDER)
  140. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  141. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  142. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  143. #endif
  144. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  145. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  146. // For the other hotends it is their distance from the extruder 0 hotend.
  147. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  148. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  149. /**
  150. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  151. *
  152. * 0 = No Power Switch
  153. * 1 = ATX
  154. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  155. *
  156. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  157. */
  158. #define POWER_SUPPLY 0
  159. #if POWER_SUPPLY > 0
  160. // Enable this option to leave the PSU off at startup.
  161. // Power to steppers and heaters will need to be turned on with M80.
  162. //#define PS_DEFAULT_OFF
  163. #endif
  164. // @section temperature
  165. //===========================================================================
  166. //============================= Thermal Settings ============================
  167. //===========================================================================
  168. /**
  169. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  170. *
  171. * Temperature sensors available:
  172. *
  173. * -3 : thermocouple with MAX31855 (only for sensor 0)
  174. * -2 : thermocouple with MAX6675 (only for sensor 0)
  175. * -1 : thermocouple with AD595
  176. * 0 : not used
  177. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  178. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  179. * 3 : Mendel-parts thermistor (4.7k pullup)
  180. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  181. * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  182. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  183. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  184. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  185. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  186. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  187. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  188. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  189. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  190. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  191. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  192. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  193. * 66 : 4.7M High Temperature thermistor from Dyze Design
  194. * 70 : the 100K thermistor found in the bq Hephestos 2
  195. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  196. *
  197. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  198. * (but gives greater accuracy and more stable PID)
  199. * 51 : 100k thermistor - EPCOS (1k pullup)
  200. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  201. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  202. *
  203. * 1047 : Pt1000 with 4k7 pullup
  204. * 1010 : Pt1000 with 1k pullup (non standard)
  205. * 147 : Pt100 with 4k7 pullup
  206. * 110 : Pt100 with 1k pullup (non standard)
  207. *
  208. * Use these for Testing or Development purposes. NEVER for production machine.
  209. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  210. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  211. *
  212. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  213. */
  214. #define TEMP_SENSOR_0 1
  215. #define TEMP_SENSOR_1 0
  216. #define TEMP_SENSOR_2 0
  217. #define TEMP_SENSOR_3 0
  218. #define TEMP_SENSOR_4 0
  219. #define TEMP_SENSOR_BED 0
  220. // Dummy thermistor constant temperature readings, for use with 998 and 999
  221. #define DUMMY_THERMISTOR_998_VALUE 25
  222. #define DUMMY_THERMISTOR_999_VALUE 100
  223. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  224. // from the two sensors differ too much the print will be aborted.
  225. //#define TEMP_SENSOR_1_AS_REDUNDANT
  226. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  227. // Extruder temperature must be close to target for this long before M109 returns success
  228. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  229. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  230. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  231. // Bed temperature must be close to target for this long before M190 returns success
  232. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  233. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  234. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  235. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  236. // to check that the wiring to the thermistor is not broken.
  237. // Otherwise this would lead to the heater being powered on all the time.
  238. #define HEATER_0_MINTEMP 5
  239. #define HEATER_1_MINTEMP 5
  240. #define HEATER_2_MINTEMP 5
  241. #define HEATER_3_MINTEMP 5
  242. #define HEATER_4_MINTEMP 5
  243. #define BED_MINTEMP 5
  244. // When temperature exceeds max temp, your heater will be switched off.
  245. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  246. // You should use MINTEMP for thermistor short/failure protection.
  247. #define HEATER_0_MAXTEMP 275
  248. #define HEATER_1_MAXTEMP 275
  249. #define HEATER_2_MAXTEMP 275
  250. #define HEATER_3_MAXTEMP 275
  251. #define HEATER_4_MAXTEMP 275
  252. #define BED_MAXTEMP 150
  253. //===========================================================================
  254. //============================= PID Settings ================================
  255. //===========================================================================
  256. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  257. // Comment the following line to disable PID and enable bang-bang.
  258. #define PIDTEMP
  259. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  260. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  261. #if ENABLED(PIDTEMP)
  262. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  263. //#define PID_DEBUG // Sends debug data to the serial port.
  264. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  265. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  266. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  267. // Set/get with gcode: M301 E[extruder number, 0-2]
  268. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  269. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  270. #define K1 0.95 //smoothing factor within the PID
  271. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  272. // Ultimaker
  273. #define DEFAULT_Kp 22.2
  274. #define DEFAULT_Ki 1.08
  275. #define DEFAULT_Kd 114
  276. // MakerGear
  277. //#define DEFAULT_Kp 7.0
  278. //#define DEFAULT_Ki 0.1
  279. //#define DEFAULT_Kd 12
  280. // Mendel Parts V9 on 12V
  281. //#define DEFAULT_Kp 63.0
  282. //#define DEFAULT_Ki 2.25
  283. //#define DEFAULT_Kd 440
  284. #endif // PIDTEMP
  285. //===========================================================================
  286. //============================= PID > Bed Temperature Control ===============
  287. //===========================================================================
  288. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  289. //
  290. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  291. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  292. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  293. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  294. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  295. // shouldn't use bed PID until someone else verifies your hardware works.
  296. // If this is enabled, find your own PID constants below.
  297. //#define PIDTEMPBED
  298. //#define BED_LIMIT_SWITCHING
  299. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  300. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  301. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  302. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  303. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  304. #if ENABLED(PIDTEMPBED)
  305. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  306. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  307. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  308. #define DEFAULT_bedKp 10.00
  309. #define DEFAULT_bedKi .023
  310. #define DEFAULT_bedKd 305.4
  311. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  312. //from pidautotune
  313. //#define DEFAULT_bedKp 97.1
  314. //#define DEFAULT_bedKi 1.41
  315. //#define DEFAULT_bedKd 1675.16
  316. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  317. #endif // PIDTEMPBED
  318. // @section extruder
  319. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  320. // It also enables the M302 command to set the minimum extrusion temperature
  321. // or to allow moving the extruder regardless of the hotend temperature.
  322. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  323. #define PREVENT_COLD_EXTRUSION
  324. #define EXTRUDE_MINTEMP 170
  325. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  326. // Note that for Bowden Extruders a too-small value here may prevent loading.
  327. #define PREVENT_LENGTHY_EXTRUDE
  328. #define EXTRUDE_MAXLENGTH 200
  329. //===========================================================================
  330. //======================== Thermal Runaway Protection =======================
  331. //===========================================================================
  332. /**
  333. * Thermal Protection protects your printer from damage and fire if a
  334. * thermistor falls out or temperature sensors fail in any way.
  335. *
  336. * The issue: If a thermistor falls out or a temperature sensor fails,
  337. * Marlin can no longer sense the actual temperature. Since a disconnected
  338. * thermistor reads as a low temperature, the firmware will keep the heater on.
  339. *
  340. * If you get "Thermal Runaway" or "Heating failed" errors the
  341. * details can be tuned in Configuration_adv.h
  342. */
  343. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  344. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  345. //===========================================================================
  346. //============================= Mechanical Settings =========================
  347. //===========================================================================
  348. // @section machine
  349. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  350. // either in the usual order or reversed
  351. //#define COREXY
  352. //#define COREXZ
  353. //#define COREYZ
  354. //#define COREYX
  355. //#define COREZX
  356. //#define COREZY
  357. //===========================================================================
  358. //============================== Endstop Settings ===========================
  359. //===========================================================================
  360. // @section homing
  361. // Specify here all the endstop connectors that are connected to any endstop or probe.
  362. // Almost all printers will be using one per axis. Probes will use one or more of the
  363. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  364. #define USE_XMIN_PLUG
  365. #define USE_YMIN_PLUG
  366. #define USE_ZMIN_PLUG
  367. //#define USE_XMAX_PLUG
  368. //#define USE_YMAX_PLUG
  369. //#define USE_ZMAX_PLUG
  370. // coarse Endstop Settings
  371. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  372. #if DISABLED(ENDSTOPPULLUPS)
  373. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  374. //#define ENDSTOPPULLUP_XMAX
  375. //#define ENDSTOPPULLUP_YMAX
  376. //#define ENDSTOPPULLUP_ZMAX
  377. //#define ENDSTOPPULLUP_XMIN
  378. //#define ENDSTOPPULLUP_YMIN
  379. //#define ENDSTOPPULLUP_ZMIN
  380. //#define ENDSTOPPULLUP_ZMIN_PROBE
  381. #endif
  382. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  383. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  384. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  385. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  386. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  387. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  388. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  389. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
  390. // Enable this feature if all enabled endstop pins are interrupt-capable.
  391. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  392. //#define ENDSTOP_INTERRUPTS_FEATURE
  393. //=============================================================================
  394. //============================== Movement Settings ============================
  395. //=============================================================================
  396. // @section motion
  397. /**
  398. * Default Settings
  399. *
  400. * These settings can be reset by M502
  401. *
  402. * Note that if EEPROM is enabled, saved values will override these.
  403. */
  404. /**
  405. * With this option each E stepper can have its own factors for the
  406. * following movement settings. If fewer factors are given than the
  407. * total number of extruders, the last value applies to the rest.
  408. */
  409. //#define DISTINCT_E_FACTORS
  410. /**
  411. * Default Axis Steps Per Unit (steps/mm)
  412. * Override with M92
  413. * X, Y, Z, E0 [, E1[, E2[, E3]]]
  414. */
  415. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  416. /**
  417. * Default Max Feed Rate (mm/s)
  418. * Override with M203
  419. * X, Y, Z, E0 [, E1[, E2[, E3]]]
  420. */
  421. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  422. /**
  423. * Default Max Acceleration (change/s) change = mm/s
  424. * (Maximum start speed for accelerated moves)
  425. * Override with M201
  426. * X, Y, Z, E0 [, E1[, E2[, E3]]]
  427. */
  428. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  429. /**
  430. * Default Acceleration (change/s) change = mm/s
  431. * Override with M204
  432. *
  433. * M204 P Acceleration
  434. * M204 R Retract Acceleration
  435. * M204 T Travel Acceleration
  436. */
  437. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  438. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  439. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  440. /**
  441. * Default Jerk (mm/s)
  442. * Override with M205 X Y Z E
  443. *
  444. * "Jerk" specifies the minimum speed change that requires acceleration.
  445. * When changing speed and direction, if the difference is less than the
  446. * value set here, it may happen instantaneously.
  447. */
  448. #define DEFAULT_XJERK 20.0
  449. #define DEFAULT_YJERK 20.0
  450. #define DEFAULT_ZJERK 0.4
  451. #define DEFAULT_EJERK 5.0
  452. //===========================================================================
  453. //============================= Z Probe Options =============================
  454. //===========================================================================
  455. // @section probes
  456. //
  457. // See http://marlinfw.org/configuration/probes.html
  458. //
  459. /**
  460. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  461. *
  462. * Enable this option for a probe connected to the Z Min endstop pin.
  463. */
  464. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  465. /**
  466. * Z_MIN_PROBE_ENDSTOP
  467. *
  468. * Enable this option for a probe connected to any pin except Z-Min.
  469. * (By default Marlin assumes the Z-Max endstop pin.)
  470. * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  471. *
  472. * - The simplest option is to use a free endstop connector.
  473. * - Use 5V for powered (usually inductive) sensors.
  474. *
  475. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  476. * - For simple switches connect...
  477. * - normally-closed switches to GND and D32.
  478. * - normally-open switches to 5V and D32.
  479. *
  480. * WARNING: Setting the wrong pin may have unexpected and potentially
  481. * disastrous consequences. Use with caution and do your homework.
  482. *
  483. */
  484. //#define Z_MIN_PROBE_ENDSTOP
  485. //#define Z_MIN_PROBE_PIN Z_MAX_PIN
  486. /**
  487. * Probe Type
  488. *
  489. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  490. * You must activate one of these to use Auto Bed Leveling below.
  491. */
  492. /**
  493. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  494. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  495. * or (with LCD_BED_LEVELING) the LCD controller.
  496. */
  497. //#define PROBE_MANUALLY
  498. /**
  499. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  500. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  501. */
  502. //#define FIX_MOUNTED_PROBE
  503. /**
  504. * Z Servo Probe, such as an endstop switch on a rotating arm.
  505. */
  506. //#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
  507. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  508. /**
  509. * The BLTouch probe is a Hall effect sensor that emulates a servo.
  510. */
  511. //#define BLTOUCH
  512. #if ENABLED(BLTOUCH)
  513. //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
  514. //#define BLTOUCH_HEATERS_OFF // Enable if the probe seems unreliable. Heaters will be disabled for each probe.
  515. #endif
  516. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  517. //#define SOLENOID_PROBE
  518. // A sled-mounted probe like those designed by Charles Bell.
  519. //#define Z_PROBE_SLED
  520. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  521. //
  522. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  523. //
  524. /**
  525. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  526. * X and Y offsets must be integers.
  527. *
  528. * In the following example the X and Y offsets are both positive:
  529. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  530. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  531. *
  532. * +-- BACK ---+
  533. * | |
  534. * L | (+) P | R <-- probe (20,20)
  535. * E | | I
  536. * F | (-) N (+) | G <-- nozzle (10,10)
  537. * T | | H
  538. * | (-) | T
  539. * | |
  540. * O-- FRONT --+
  541. * (0,0)
  542. */
  543. #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
  544. #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
  545. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
  546. // X and Y axis travel speed (mm/m) between probes
  547. #define XY_PROBE_SPEED 8000
  548. // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
  549. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  550. // Speed for the "accurate" probe of each point
  551. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  552. // Use double touch for probing
  553. //#define PROBE_DOUBLE_TOUCH
  554. /**
  555. * Z probes require clearance when deploying, stowing, and moving between
  556. * probe points to avoid hitting the bed and other hardware.
  557. * Servo-mounted probes require extra space for the arm to rotate.
  558. * Inductive probes need space to keep from triggering early.
  559. *
  560. * Use these settings to specify the distance (mm) to raise the probe (or
  561. * lower the bed). The values set here apply over and above any (negative)
  562. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  563. * Only integer values >= 1 are valid here.
  564. *
  565. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  566. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  567. */
  568. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  569. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  570. // For M851 give a range for adjusting the Z probe offset
  571. #define Z_PROBE_OFFSET_RANGE_MIN -20
  572. #define Z_PROBE_OFFSET_RANGE_MAX 20
  573. // Enable the M48 repeatability test to test probe accuracy
  574. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  575. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  576. // :{ 0:'Low', 1:'High' }
  577. #define X_ENABLE_ON 0
  578. #define Y_ENABLE_ON 0
  579. #define Z_ENABLE_ON 0
  580. #define E_ENABLE_ON 0 // For all extruders
  581. // Disables axis stepper immediately when it's not being used.
  582. // WARNING: When motors turn off there is a chance of losing position accuracy!
  583. #define DISABLE_X false
  584. #define DISABLE_Y false
  585. #define DISABLE_Z false
  586. // Warn on display about possibly reduced accuracy
  587. //#define DISABLE_REDUCED_ACCURACY_WARNING
  588. // @section extruder
  589. #define DISABLE_E false // For all extruders
  590. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  591. // @section machine
  592. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  593. #define INVERT_X_DIR false
  594. #define INVERT_Y_DIR true
  595. #define INVERT_Z_DIR false
  596. // Enable this option for Toshiba stepper drivers
  597. //#define CONFIG_STEPPERS_TOSHIBA
  598. // @section extruder
  599. // For direct drive extruder v9 set to true, for geared extruder set to false.
  600. #define INVERT_E0_DIR false
  601. #define INVERT_E1_DIR false
  602. #define INVERT_E2_DIR false
  603. #define INVERT_E3_DIR false
  604. #define INVERT_E4_DIR false
  605. // @section homing
  606. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  607. // Be sure you have this distance over your Z_MAX_POS in case.
  608. // Direction of endstops when homing; 1=MAX, -1=MIN
  609. // :[-1,1]
  610. #define X_HOME_DIR -1
  611. #define Y_HOME_DIR -1
  612. #define Z_HOME_DIR -1
  613. // @section machine
  614. // Travel limits after homing (units are in mm)
  615. #define X_MIN_POS 0
  616. #define Y_MIN_POS 0
  617. #define Z_MIN_POS 0
  618. #define X_MAX_POS 200
  619. #define Y_MAX_POS 200
  620. #define Z_MAX_POS 200
  621. // If enabled, axes won't move below MIN_POS in response to movement commands.
  622. #define MIN_SOFTWARE_ENDSTOPS
  623. // If enabled, axes won't move above MAX_POS in response to movement commands.
  624. #define MAX_SOFTWARE_ENDSTOPS
  625. /**
  626. * Filament Runout Sensor
  627. * A mechanical or opto endstop is used to check for the presence of filament.
  628. *
  629. * RAMPS-based boards use SERVO3_PIN.
  630. * For other boards you may need to define FIL_RUNOUT_PIN.
  631. * By default the firmware assumes HIGH = has filament, LOW = ran out
  632. */
  633. //#define FILAMENT_RUNOUT_SENSOR
  634. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  635. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  636. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  637. #define FILAMENT_RUNOUT_SCRIPT "M600"
  638. #endif
  639. //===========================================================================
  640. //=============================== Bed Leveling ==============================
  641. //===========================================================================
  642. // @section bedlevel
  643. /**
  644. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  645. * and behavior of G29 will change depending on your selection.
  646. *
  647. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  648. *
  649. * - AUTO_BED_LEVELING_3POINT
  650. * Probe 3 arbitrary points on the bed (that aren't collinear)
  651. * You specify the XY coordinates of all 3 points.
  652. * The result is a single tilted plane. Best for a flat bed.
  653. *
  654. * - AUTO_BED_LEVELING_LINEAR
  655. * Probe several points in a grid.
  656. * You specify the rectangle and the density of sample points.
  657. * The result is a single tilted plane. Best for a flat bed.
  658. *
  659. * - AUTO_BED_LEVELING_BILINEAR
  660. * Probe several points in a grid.
  661. * You specify the rectangle and the density of sample points.
  662. * The result is a mesh, best for large or uneven beds.
  663. *
  664. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  665. * A comprehensive bed leveling system combining the features and benefits
  666. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  667. * Validation and Mesh Editing systems. Currently, UBL is only checked out
  668. * for Cartesian Printers. That said, it was primarily designed to correct
  669. * poor quality Delta Printers. If you feel adventurous and have a Delta,
  670. * please post an issue if something doesn't work correctly. Initially,
  671. * you will need to set a reduced bed size so you have a rectangular area
  672. * to test on.
  673. *
  674. * - MESH_BED_LEVELING
  675. * Probe a grid manually
  676. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  677. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  678. * leveling in steps so you can manually adjust the Z height at each grid-point.
  679. * With an LCD controller the process is guided step-by-step.
  680. */
  681. //#define AUTO_BED_LEVELING_3POINT
  682. //#define AUTO_BED_LEVELING_LINEAR
  683. //#define AUTO_BED_LEVELING_BILINEAR
  684. //#define AUTO_BED_LEVELING_UBL
  685. //#define MESH_BED_LEVELING
  686. /**
  687. * Enable detailed logging of G28, G29, M48, etc.
  688. * Turn on with the command 'M111 S32'.
  689. * NOTE: Requires a lot of PROGMEM!
  690. */
  691. //#define DEBUG_LEVELING_FEATURE
  692. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  693. // Gradually reduce leveling correction until a set height is reached,
  694. // at which point movement will be level to the machine's XY plane.
  695. // The height can be set with M420 Z<height>
  696. #define ENABLE_LEVELING_FADE_HEIGHT
  697. #endif
  698. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  699. // Set the number of grid points per dimension.
  700. #define GRID_MAX_POINTS_X 3
  701. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  702. // Set the boundaries for probing (where the probe can reach).
  703. #define LEFT_PROBE_BED_POSITION 15
  704. #define RIGHT_PROBE_BED_POSITION 170
  705. #define FRONT_PROBE_BED_POSITION 20
  706. #define BACK_PROBE_BED_POSITION 170
  707. // The Z probe minimum outer margin (to validate G29 parameters).
  708. #define MIN_PROBE_EDGE 10
  709. // Probe along the Y axis, advancing X after each column
  710. //#define PROBE_Y_FIRST
  711. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  712. //
  713. // Experimental Subdivision of the grid by Catmull-Rom method.
  714. // Synthesizes intermediate points to produce a more detailed mesh.
  715. //
  716. //#define ABL_BILINEAR_SUBDIVISION
  717. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  718. // Number of subdivisions between probe points
  719. #define BILINEAR_SUBDIVISIONS 3
  720. #endif
  721. #endif
  722. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  723. // 3 arbitrary points to probe.
  724. // A simple cross-product is used to estimate the plane of the bed.
  725. #define ABL_PROBE_PT_1_X 15
  726. #define ABL_PROBE_PT_1_Y 180
  727. #define ABL_PROBE_PT_2_X 15
  728. #define ABL_PROBE_PT_2_Y 20
  729. #define ABL_PROBE_PT_3_X 170
  730. #define ABL_PROBE_PT_3_Y 20
  731. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  732. //===========================================================================
  733. //========================= Unified Bed Leveling ============================
  734. //===========================================================================
  735. #define UBL_MESH_INSET 1 // Mesh inset margin on print area
  736. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  737. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  738. #define UBL_PROBE_PT_1_X 39 // These set the probe locations for when UBL does a 3-Point leveling
  739. #define UBL_PROBE_PT_1_Y 180 // of the mesh.
  740. #define UBL_PROBE_PT_2_X 39
  741. #define UBL_PROBE_PT_2_Y 20
  742. #define UBL_PROBE_PT_3_X 180
  743. #define UBL_PROBE_PT_3_Y 20
  744. //#define UBL_G26_MESH_EDITING // Enable G26 mesh editing
  745. #elif ENABLED(MESH_BED_LEVELING)
  746. //===========================================================================
  747. //=================================== Mesh ==================================
  748. //===========================================================================
  749. #define MESH_INSET 10 // Mesh inset margin on print area
  750. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  751. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  752. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  753. #endif // BED_LEVELING
  754. /**
  755. * Use the LCD controller for bed leveling
  756. * Requires MESH_BED_LEVELING or PROBE_MANUALLY
  757. */
  758. //#define LCD_BED_LEVELING
  759. #if ENABLED(LCD_BED_LEVELING)
  760. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  761. #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  762. #endif
  763. /**
  764. * Commands to execute at the end of G29 probing.
  765. * Useful to retract or move the Z probe out of the way.
  766. */
  767. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  768. // @section homing
  769. // The center of the bed is at (X=0, Y=0)
  770. //#define BED_CENTER_AT_0_0
  771. // Manually set the home position. Leave these undefined for automatic settings.
  772. // For DELTA this is the top-center of the Cartesian print volume.
  773. //#define MANUAL_X_HOME_POS 0
  774. //#define MANUAL_Y_HOME_POS 0
  775. //#define MANUAL_Z_HOME_POS 0
  776. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  777. //
  778. // With this feature enabled:
  779. //
  780. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  781. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  782. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  783. // - Prevent Z homing when the Z probe is outside bed area.
  784. //#define Z_SAFE_HOMING
  785. #if ENABLED(Z_SAFE_HOMING)
  786. #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
  787. #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
  788. #endif
  789. // Homing speeds (mm/m)
  790. #define HOMING_FEEDRATE_XY (50*60)
  791. #define HOMING_FEEDRATE_Z (4*60)
  792. //=============================================================================
  793. //============================= Additional Features ===========================
  794. //=============================================================================
  795. // @section extras
  796. //
  797. // EEPROM
  798. //
  799. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  800. // M500 - stores parameters in EEPROM
  801. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  802. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  803. //define this to enable EEPROM support
  804. //#define EEPROM_SETTINGS
  805. #if ENABLED(EEPROM_SETTINGS)
  806. // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
  807. #define EEPROM_CHITCHAT // Please keep turned on if you can.
  808. #endif
  809. //
  810. // Host Keepalive
  811. //
  812. // When enabled Marlin will send a busy status message to the host
  813. // every couple of seconds when it can't accept commands.
  814. //
  815. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  816. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  817. //
  818. // M100 Free Memory Watcher
  819. //
  820. //#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
  821. //
  822. // G20/G21 Inch mode support
  823. //
  824. //#define INCH_MODE_SUPPORT
  825. //
  826. // M149 Set temperature units support
  827. //
  828. //#define TEMPERATURE_UNITS_SUPPORT
  829. // @section temperature
  830. // Preheat Constants
  831. #define PREHEAT_1_TEMP_HOTEND 180
  832. #define PREHEAT_1_TEMP_BED 70
  833. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  834. #define PREHEAT_2_TEMP_HOTEND 240
  835. #define PREHEAT_2_TEMP_BED 110
  836. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  837. //
  838. // Nozzle Park -- EXPERIMENTAL
  839. //
  840. // When enabled allows the user to define a special XYZ position, inside the
  841. // machine's topology, to park the nozzle when idle or when receiving the G27
  842. // command.
  843. //
  844. // The "P" paramenter controls what is the action applied to the Z axis:
  845. // P0: (Default) If current Z-pos is lower than Z-park then the nozzle will
  846. // be raised to reach Z-park height.
  847. //
  848. // P1: No matter the current Z-pos, the nozzle will be raised/lowered to
  849. // reach Z-park height.
  850. //
  851. // P2: The nozzle height will be raised by Z-park amount but never going over
  852. // the machine's limit of Z_MAX_POS.
  853. //
  854. //#define NOZZLE_PARK_FEATURE
  855. #if ENABLED(NOZZLE_PARK_FEATURE)
  856. // Specify a park position as { X, Y, Z }
  857. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  858. #endif
  859. //
  860. // Clean Nozzle Feature -- EXPERIMENTAL
  861. //
  862. // When enabled allows the user to send G12 to start the nozzle cleaning
  863. // process, the G-Code accepts two parameters:
  864. // "P" for pattern selection
  865. // "S" for defining the number of strokes/repetitions
  866. //
  867. // Available list of patterns:
  868. // P0: This is the default pattern, this process requires a sponge type
  869. // material at a fixed bed location. S defines "strokes" i.e.
  870. // back-and-forth movements between the starting and end points.
  871. //
  872. // P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T"
  873. // defines the number of zig-zag triangles to be done. "S" defines the
  874. // number of strokes aka one back-and-forth movement. Zig-zags will
  875. // be performed in whichever dimension is smallest. As an example,
  876. // sending "G12 P1 S1 T3" will execute:
  877. //
  878. // --
  879. // | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  880. // | | / \ / \ / \ |
  881. // A | | / \ / \ / \ |
  882. // | | / \ / \ / \ |
  883. // | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  884. // -- +--------------------------------+
  885. // |________|_________|_________|
  886. // T1 T2 T3
  887. //
  888. // P2: This starts a circular pattern with circle with middle in
  889. // NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
  890. // Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
  891. //
  892. // Caveats: End point Z should use the same value as Start point Z.
  893. //
  894. // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
  895. // may change to add new functionality like different wipe patterns.
  896. //
  897. //#define NOZZLE_CLEAN_FEATURE
  898. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  899. // Default number of pattern repetitions
  900. #define NOZZLE_CLEAN_STROKES 12
  901. // Default number of triangles
  902. #define NOZZLE_CLEAN_TRIANGLES 3
  903. // Specify positions as { X, Y, Z }
  904. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  905. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  906. // Circular pattern radius
  907. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  908. // Circular pattern circle fragments number
  909. #define NOZZLE_CLEAN_CIRCLE_FN 10
  910. // Middle point of circle
  911. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  912. // Moves the nozzle to the initial position
  913. #define NOZZLE_CLEAN_GOBACK
  914. #endif
  915. //
  916. // Print job timer
  917. //
  918. // Enable this option to automatically start and stop the
  919. // print job timer when M104/M109/M190 commands are received.
  920. // M104 (extruder without wait) - high temp = none, low temp = stop timer
  921. // M109 (extruder with wait) - high temp = start timer, low temp = stop timer
  922. // M190 (bed with wait) - high temp = start timer, low temp = none
  923. //
  924. // In all cases the timer can be started and stopped using
  925. // the following commands:
  926. //
  927. // - M75 - Start the print job timer
  928. // - M76 - Pause the print job timer
  929. // - M77 - Stop the print job timer
  930. #define PRINTJOB_TIMER_AUTOSTART
  931. //
  932. // Print Counter
  933. //
  934. // When enabled Marlin will keep track of some print statistical data such as:
  935. // - Total print jobs
  936. // - Total successful print jobs
  937. // - Total failed print jobs
  938. // - Total time printing
  939. //
  940. // This information can be viewed by the M78 command.
  941. //#define PRINTCOUNTER
  942. //=============================================================================
  943. //============================= LCD and SD support ============================
  944. //=============================================================================
  945. // @section lcd
  946. //
  947. // LCD LANGUAGE
  948. //
  949. // Here you may choose the language used by Marlin on the LCD menus, the following
  950. // list of languages are available:
  951. // en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
  952. // kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test
  953. //
  954. // :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' }
  955. //
  956. #define LCD_LANGUAGE en
  957. //
  958. // LCD Character Set
  959. //
  960. // Note: This option is NOT applicable to Graphical Displays.
  961. //
  962. // All character-based LCD's provide ASCII plus one of these
  963. // language extensions:
  964. //
  965. // - JAPANESE ... the most common
  966. // - WESTERN ... with more accented characters
  967. // - CYRILLIC ... for the Russian language
  968. //
  969. // To determine the language extension installed on your controller:
  970. //
  971. // - Compile and upload with LCD_LANGUAGE set to 'test'
  972. // - Click the controller to view the LCD menu
  973. // - The LCD will display Japanese, Western, or Cyrillic text
  974. //
  975. // See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
  976. //
  977. // :['JAPANESE', 'WESTERN', 'CYRILLIC']
  978. //
  979. #define DISPLAY_CHARSET_HD44780 JAPANESE
  980. //
  981. // LCD TYPE
  982. //
  983. // You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
  984. // 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
  985. // (ST7565R family). (This option will be set automatically for certain displays.)
  986. //
  987. // IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
  988. // https://github.com/olikraus/U8glib_Arduino
  989. //
  990. //#define ULTRA_LCD // Character based
  991. //#define DOGLCD // Full graphics display
  992. //
  993. // SD CARD
  994. //
  995. // SD Card support is disabled by default. If your controller has an SD slot,
  996. // you must uncomment the following option or it won't work.
  997. //
  998. //#define SDSUPPORT
  999. //
  1000. // SD CARD: SPI SPEED
  1001. //
  1002. // Uncomment ONE of the following items to use a slower SPI transfer
  1003. // speed. This is usually required if you're getting volume init errors.
  1004. //
  1005. //#define SPI_SPEED SPI_HALF_SPEED
  1006. //#define SPI_SPEED SPI_QUARTER_SPEED
  1007. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1008. //
  1009. // SD CARD: ENABLE CRC
  1010. //
  1011. // Use CRC checks and retries on the SD communication.
  1012. //
  1013. //#define SD_CHECK_AND_RETRY
  1014. //
  1015. // ENCODER SETTINGS
  1016. //
  1017. // This option overrides the default number of encoder pulses needed to
  1018. // produce one step. Should be increased for high-resolution encoders.
  1019. //
  1020. //#define ENCODER_PULSES_PER_STEP 1
  1021. //
  1022. // Use this option to override the number of step signals required to
  1023. // move between next/prev menu items.
  1024. //
  1025. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  1026. /**
  1027. * Encoder Direction Options
  1028. *
  1029. * Test your encoder's behavior first with both options disabled.
  1030. *
  1031. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1032. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1033. * Reversed Value Editing only? Enable BOTH options.
  1034. */
  1035. //
  1036. // This option reverses the encoder direction everywhere
  1037. //
  1038. // Set this option if CLOCKWISE causes values to DECREASE
  1039. //
  1040. //#define REVERSE_ENCODER_DIRECTION
  1041. //
  1042. // This option reverses the encoder direction for navigating LCD menus.
  1043. //
  1044. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1045. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1046. //
  1047. //#define REVERSE_MENU_DIRECTION
  1048. //
  1049. // Individual Axis Homing
  1050. //
  1051. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1052. //
  1053. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1054. //
  1055. // SPEAKER/BUZZER
  1056. //
  1057. // If you have a speaker that can produce tones, enable it here.
  1058. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1059. //
  1060. //#define SPEAKER
  1061. //
  1062. // The duration and frequency for the UI feedback sound.
  1063. // Set these to 0 to disable audio feedback in the LCD menus.
  1064. //
  1065. // Note: Test audio output with the G-Code:
  1066. // M300 S<frequency Hz> P<duration ms>
  1067. //
  1068. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1069. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1070. //
  1071. // CONTROLLER TYPE: Standard
  1072. //
  1073. // Marlin supports a wide variety of controllers.
  1074. // Enable one of the following options to specify your controller.
  1075. //
  1076. //
  1077. // ULTIMAKER Controller.
  1078. //
  1079. //#define ULTIMAKERCONTROLLER
  1080. //
  1081. // ULTIPANEL as seen on Thingiverse.
  1082. //
  1083. //#define ULTIPANEL
  1084. //
  1085. // Cartesio UI
  1086. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1087. //
  1088. //#define CARTESIO_UI
  1089. //
  1090. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1091. // http://reprap.org/wiki/PanelOne
  1092. //
  1093. //#define PANEL_ONE
  1094. //
  1095. // MaKr3d Makr-Panel with graphic controller and SD support.
  1096. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1097. //
  1098. //#define MAKRPANEL
  1099. //
  1100. // ReprapWorld Graphical LCD
  1101. // https://reprapworld.com/?products_details&products_id/1218
  1102. //
  1103. //#define REPRAPWORLD_GRAPHICAL_LCD
  1104. //
  1105. // Activate one of these if you have a Panucatt Devices
  1106. // Viki 2.0 or mini Viki with Graphic LCD
  1107. // http://panucatt.com
  1108. //
  1109. //#define VIKI2
  1110. //#define miniVIKI
  1111. //
  1112. // Adafruit ST7565 Full Graphic Controller.
  1113. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1114. //
  1115. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1116. //
  1117. // RepRapDiscount Smart Controller.
  1118. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1119. //
  1120. // Note: Usually sold with a white PCB.
  1121. //
  1122. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1123. //
  1124. // GADGETS3D G3D LCD/SD Controller
  1125. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1126. //
  1127. // Note: Usually sold with a blue PCB.
  1128. //
  1129. //#define G3D_PANEL
  1130. //
  1131. // RepRapDiscount FULL GRAPHIC Smart Controller
  1132. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1133. //
  1134. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1135. //
  1136. // MakerLab Mini Panel with graphic
  1137. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1138. //
  1139. //#define MINIPANEL
  1140. //
  1141. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1142. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1143. //
  1144. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1145. // is pressed, a value of 10.0 means 10mm per click.
  1146. //
  1147. //#define REPRAPWORLD_KEYPAD
  1148. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1149. //
  1150. // RigidBot Panel V1.0
  1151. // http://www.inventapart.com/
  1152. //
  1153. //#define RIGIDBOT_PANEL
  1154. //
  1155. // BQ LCD Smart Controller shipped by
  1156. // default with the BQ Hephestos 2 and Witbox 2.
  1157. //
  1158. //#define BQ_LCD_SMART_CONTROLLER
  1159. //
  1160. // CONTROLLER TYPE: I2C
  1161. //
  1162. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1163. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1164. //
  1165. //
  1166. // Elefu RA Board Control Panel
  1167. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1168. //
  1169. //#define RA_CONTROL_PANEL
  1170. //
  1171. // Sainsmart YW Robot (LCM1602) LCD Display
  1172. //
  1173. //#define LCD_I2C_SAINSMART_YWROBOT
  1174. //
  1175. // Generic LCM1602 LCD adapter
  1176. //
  1177. //#define LCM1602
  1178. //
  1179. // PANELOLU2 LCD with status LEDs,
  1180. // separate encoder and click inputs.
  1181. //
  1182. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1183. // For more info: https://github.com/lincomatic/LiquidTWI2
  1184. //
  1185. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1186. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1187. //
  1188. //#define LCD_I2C_PANELOLU2
  1189. //
  1190. // Panucatt VIKI LCD with status LEDs,
  1191. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1192. //
  1193. //#define LCD_I2C_VIKI
  1194. //
  1195. // SSD1306 OLED full graphics generic display
  1196. //
  1197. //#define U8GLIB_SSD1306
  1198. //
  1199. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1200. //
  1201. //#define SAV_3DGLCD
  1202. #if ENABLED(SAV_3DGLCD)
  1203. //#define U8GLIB_SSD1306
  1204. #define U8GLIB_SH1106
  1205. #endif
  1206. //
  1207. // CONTROLLER TYPE: Shift register panels
  1208. //
  1209. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1210. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1211. //
  1212. //#define SAV_3DLCD
  1213. //
  1214. // TinyBoy2 128x64 OLED / Encoder Panel
  1215. //
  1216. //#define OLED_PANEL_TINYBOY2
  1217. //=============================================================================
  1218. //=============================== Extra Features ==============================
  1219. //=============================================================================
  1220. // @section extras
  1221. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1222. //#define FAST_PWM_FAN
  1223. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1224. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1225. // is too low, you should also increment SOFT_PWM_SCALE.
  1226. //#define FAN_SOFT_PWM
  1227. // Incrementing this by 1 will double the software PWM frequency,
  1228. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1229. // However, control resolution will be halved for each increment;
  1230. // at zero value, there are 128 effective control positions.
  1231. #define SOFT_PWM_SCALE 0
  1232. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1233. // be used to mitigate the associated resolution loss. If enabled,
  1234. // some of the PWM cycles are stretched so on average the desired
  1235. // duty cycle is attained.
  1236. //#define SOFT_PWM_DITHER
  1237. // Temperature status LEDs that display the hotend and bed temperature.
  1238. // If all hotends, bed temperature, and target temperature are under 54C
  1239. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1240. //#define TEMP_STAT_LEDS
  1241. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1242. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1243. //#define PHOTOGRAPH_PIN 23
  1244. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1245. //#define SF_ARC_FIX
  1246. // Support for the BariCUDA Paste Extruder.
  1247. //#define BARICUDA
  1248. //define BlinkM/CyzRgb Support
  1249. //#define BLINKM
  1250. /**
  1251. * RGB LED / LED Strip Control
  1252. *
  1253. * Enable support for an RGB LED connected to 5V digital pins, or
  1254. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1255. *
  1256. * Adds the M150 command to set the LED (or LED strip) color.
  1257. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1258. * luminance values can be set from 0 to 255.
  1259. *
  1260. * *** CAUTION ***
  1261. * LED Strips require a MOFSET Chip between PWM lines and LEDs,
  1262. * as the Arduino cannot handle the current the LEDs will require.
  1263. * Failure to follow this precaution can destroy your Arduino!
  1264. * *** CAUTION ***
  1265. *
  1266. */
  1267. //#define RGB_LED
  1268. //#define RGBW_LED
  1269. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1270. #define RGB_LED_R_PIN 34
  1271. #define RGB_LED_G_PIN 43
  1272. #define RGB_LED_B_PIN 35
  1273. #define RGB_LED_W_PIN -1
  1274. #endif
  1275. /**
  1276. * Printer Event LEDs
  1277. *
  1278. * During printing, the LEDs will reflect the printer status:
  1279. *
  1280. * - Gradually change from blue to violet as the heated bed gets to target temp
  1281. * - Gradually change from violet to red as the hotend gets to temperature
  1282. * - Change to white to illuminate work surface
  1283. * - Change to green once print has finished
  1284. * - Turn off after the print has finished and the user has pushed a button
  1285. */
  1286. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1287. #define PRINTER_EVENT_LEDS
  1288. #endif
  1289. /*********************************************************************\
  1290. * R/C SERVO support
  1291. * Sponsored by TrinityLabs, Reworked by codexmas
  1292. **********************************************************************/
  1293. // Number of servos
  1294. //
  1295. // If you select a configuration below, this will receive a default value and does not need to be set manually
  1296. // set it manually if you have more servos than extruders and wish to manually control some
  1297. // leaving it undefined or defining as 0 will disable the servo subsystem
  1298. // If unsure, leave commented / disabled
  1299. //
  1300. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1301. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1302. // 300ms is a good value but you can try less delay.
  1303. // If the servo can't reach the requested position, increase it.
  1304. #define SERVO_DELAY 300
  1305. // Servo deactivation
  1306. //
  1307. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1308. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1309. /**
  1310. * Filament Width Sensor
  1311. *
  1312. * Measures the filament width in real-time and adjusts
  1313. * flow rate to compensate for any irregularities.
  1314. *
  1315. * Also allows the measured filament diameter to set the
  1316. * extrusion rate, so the slicer only has to specify the
  1317. * volume.
  1318. *
  1319. * Only a single extruder is supported at this time.
  1320. *
  1321. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  1322. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  1323. * 301 RAMBO : Analog input 3
  1324. *
  1325. * Note: May require analog pins to be defined for other boards.
  1326. */
  1327. //#define FILAMENT_WIDTH_SENSOR
  1328. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
  1329. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  1330. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
  1331. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  1332. #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
  1333. #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
  1334. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  1335. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  1336. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  1337. //#define FILAMENT_LCD_DISPLAY
  1338. #endif
  1339. #endif // CONFIGURATION_H