My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Você não pode selecionar mais de 25 tópicos Os tópicos devem começar com uma letra ou um número, podem incluir traços ('-') e podem ter até 35 caracteres.

Configuration_adv.h 59KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration_adv.h
  24. *
  25. * Advanced settings.
  26. * Only change these if you know exactly what you're doing.
  27. * Some of these settings can damage your printer if improperly set!
  28. *
  29. * Basic settings can be found in Configuration.h
  30. *
  31. */
  32. #ifndef CONFIGURATION_ADV_H
  33. #define CONFIGURATION_ADV_H
  34. #define CONFIGURATION_ADV_H_VERSION 020000
  35. // @section temperature
  36. //===========================================================================
  37. //=============================Thermal Settings ============================
  38. //===========================================================================
  39. #if DISABLED(PIDTEMPBED)
  40. #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
  41. #if ENABLED(BED_LIMIT_SWITCHING)
  42. #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
  43. #endif
  44. #endif
  45. /**
  46. * Thermal Protection protects your printer from damage and fire if a
  47. * thermistor falls out or temperature sensors fail in any way.
  48. *
  49. * The issue: If a thermistor falls out or a temperature sensor fails,
  50. * Marlin can no longer sense the actual temperature. Since a disconnected
  51. * thermistor reads as a low temperature, the firmware will keep the heater on.
  52. *
  53. * The solution: Once the temperature reaches the target, start observing.
  54. * If the temperature stays too far below the target (hysteresis) for too long (period),
  55. * the firmware will halt the machine as a safety precaution.
  56. *
  57. * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  58. */
  59. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  60. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  61. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  62. /**
  63. * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
  64. * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
  65. * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
  66. * but only if the current temperature is far enough below the target for a reliable test.
  67. *
  68. * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
  69. * WATCH_TEMP_INCREASE should not be below 2.
  70. */
  71. #define WATCH_TEMP_PERIOD 20 // Seconds
  72. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  73. #endif
  74. /**
  75. * Thermal Protection parameters for the bed are just as above for hotends.
  76. */
  77. #if ENABLED(THERMAL_PROTECTION_BED)
  78. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  79. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  80. /**
  81. * Whenever an M140 or M190 increases the target temperature the firmware will wait for the
  82. * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
  83. * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
  84. * but only if the current temperature is far enough below the target for a reliable test.
  85. *
  86. * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
  87. * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
  88. */
  89. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  90. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  91. #endif
  92. #if ENABLED(PIDTEMP)
  93. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  94. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
  95. //#define PID_EXTRUSION_SCALING
  96. #if ENABLED(PID_EXTRUSION_SCALING)
  97. #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
  98. #define LPQ_MAX_LEN 50
  99. #endif
  100. #endif
  101. /**
  102. * Automatic Temperature:
  103. * The hotend target temperature is calculated by all the buffered lines of gcode.
  104. * The maximum buffered steps/sec of the extruder motor is called "se".
  105. * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
  106. * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
  107. * mintemp and maxtemp. Turn this off by executing M109 without F*
  108. * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
  109. * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
  110. */
  111. #define AUTOTEMP
  112. #if ENABLED(AUTOTEMP)
  113. #define AUTOTEMP_OLDWEIGHT 0.98
  114. #endif
  115. // Show Temperature ADC value
  116. // Enable for M105 to include ADC values read from temperature sensors.
  117. //#define SHOW_TEMP_ADC_VALUES
  118. /**
  119. * High Temperature Thermistor Support
  120. *
  121. * Thermistors able to support high temperature tend to have a hard time getting
  122. * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
  123. * will probably be caught when the heating element first turns on during the
  124. * preheating process, which will trigger a min_temp_error as a safety measure
  125. * and force stop everything.
  126. * To circumvent this limitation, we allow for a preheat time (during which,
  127. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  128. * aberrant readings.
  129. *
  130. * If you want to enable this feature for your hotend thermistor(s)
  131. * uncomment and set values > 0 in the constants below
  132. */
  133. // The number of consecutive low temperature errors that can occur
  134. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  135. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  136. // The number of milliseconds a hotend will preheat before starting to check
  137. // the temperature. This value should NOT be set to the time it takes the
  138. // hot end to reach the target temperature, but the time it takes to reach
  139. // the minimum temperature your thermistor can read. The lower the better/safer.
  140. // This shouldn't need to be more than 30 seconds (30000)
  141. //#define MILLISECONDS_PREHEAT_TIME 0
  142. // @section extruder
  143. // Extruder runout prevention.
  144. // If the machine is idle and the temperature over MINTEMP
  145. // then extrude some filament every couple of SECONDS.
  146. //#define EXTRUDER_RUNOUT_PREVENT
  147. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  148. #define EXTRUDER_RUNOUT_MINTEMP 190
  149. #define EXTRUDER_RUNOUT_SECONDS 30
  150. #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
  151. #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
  152. #endif
  153. // @section temperature
  154. //These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
  155. //The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
  156. #define TEMP_SENSOR_AD595_OFFSET 0.0
  157. #define TEMP_SENSOR_AD595_GAIN 1.0
  158. /**
  159. * Controller Fan
  160. * To cool down the stepper drivers and MOSFETs.
  161. *
  162. * The fan will turn on automatically whenever any stepper is enabled
  163. * and turn off after a set period after all steppers are turned off.
  164. */
  165. //#define USE_CONTROLLER_FAN
  166. #if ENABLED(USE_CONTROLLER_FAN)
  167. //#define CONTROLLER_FAN_PIN FAN1_PIN // Set a custom pin for the controller fan
  168. #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
  169. #define CONTROLLERFAN_SPEED 255 // 255 == full speed
  170. #endif
  171. // When first starting the main fan, run it at full speed for the
  172. // given number of milliseconds. This gets the fan spinning reliably
  173. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  174. //#define FAN_KICKSTART_TIME 100
  175. // This defines the minimal speed for the main fan, run in PWM mode
  176. // to enable uncomment and set minimal PWM speed for reliable running (1-255)
  177. // if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
  178. //#define FAN_MIN_PWM 50
  179. // @section extruder
  180. /**
  181. * Extruder cooling fans
  182. *
  183. * Extruder auto fans automatically turn on when their extruders'
  184. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  185. *
  186. * Your board's pins file specifies the recommended pins. Override those here
  187. * or set to -1 to disable completely.
  188. *
  189. * Multiple extruders can be assigned to the same pin in which case
  190. * the fan will turn on when any selected extruder is above the threshold.
  191. */
  192. #define E0_AUTO_FAN_PIN -1
  193. #define E1_AUTO_FAN_PIN -1
  194. #define E2_AUTO_FAN_PIN -1
  195. #define E3_AUTO_FAN_PIN -1
  196. #define E4_AUTO_FAN_PIN -1
  197. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  198. #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
  199. /**
  200. * Part-Cooling Fan Multiplexer
  201. *
  202. * This feature allows you to digitally multiplex the fan output.
  203. * The multiplexer is automatically switched at tool-change.
  204. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  205. */
  206. #define FANMUX0_PIN -1
  207. #define FANMUX1_PIN -1
  208. #define FANMUX2_PIN -1
  209. /**
  210. * M355 Case Light on-off / brightness
  211. */
  212. //#define CASE_LIGHT_ENABLE
  213. #if ENABLED(CASE_LIGHT_ENABLE)
  214. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  215. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  216. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  217. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  218. //#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
  219. #endif
  220. //===========================================================================
  221. //============================ Mechanical Settings ==========================
  222. //===========================================================================
  223. // @section homing
  224. // If you want endstops to stay on (by default) even when not homing
  225. // enable this option. Override at any time with M120, M121.
  226. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  227. // @section extras
  228. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  229. // Dual X Steppers
  230. // Uncomment this option to drive two X axis motors.
  231. // The next unused E driver will be assigned to the second X stepper.
  232. //#define X_DUAL_STEPPER_DRIVERS
  233. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  234. // Set true if the two X motors need to rotate in opposite directions
  235. #define INVERT_X2_VS_X_DIR true
  236. #endif
  237. // Dual Y Steppers
  238. // Uncomment this option to drive two Y axis motors.
  239. // The next unused E driver will be assigned to the second Y stepper.
  240. //#define Y_DUAL_STEPPER_DRIVERS
  241. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  242. // Set true if the two Y motors need to rotate in opposite directions
  243. #define INVERT_Y2_VS_Y_DIR true
  244. #endif
  245. // A single Z stepper driver is usually used to drive 2 stepper motors.
  246. // Uncomment this option to use a separate stepper driver for each Z axis motor.
  247. // The next unused E driver will be assigned to the second Z stepper.
  248. //#define Z_DUAL_STEPPER_DRIVERS
  249. #if ENABLED(Z_DUAL_STEPPER_DRIVERS)
  250. // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
  251. // That way the machine is capable to align the bed during home, since both Z steppers are homed.
  252. // There is also an implementation of M666 (software endstops adjustment) to this feature.
  253. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
  254. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
  255. // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
  256. // Play a little bit with small adjustments (0.5mm) and check the behaviour.
  257. // The M119 (endstops report) will start reporting the Z2 Endstop as well.
  258. //#define Z_DUAL_ENDSTOPS
  259. #if ENABLED(Z_DUAL_ENDSTOPS)
  260. #define Z2_USE_ENDSTOP _XMAX_
  261. #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // Use M666 to determine/test this value
  262. #endif
  263. #endif // Z_DUAL_STEPPER_DRIVERS
  264. // Enable this for dual x-carriage printers.
  265. // A dual x-carriage design has the advantage that the inactive extruder can be parked which
  266. // prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
  267. // allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
  268. //#define DUAL_X_CARRIAGE
  269. #if ENABLED(DUAL_X_CARRIAGE)
  270. // Configuration for second X-carriage
  271. // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
  272. // the second x-carriage always homes to the maximum endstop.
  273. #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
  274. #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
  275. #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
  276. #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
  277. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  278. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  279. // without modifying the firmware (through the "M218 T1 X???" command).
  280. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  281. // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
  282. // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
  283. // as long as it supports dual x-carriages. (M605 S0)
  284. // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
  285. // that additional slicer support is not required. (M605 S1)
  286. // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
  287. // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
  288. // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
  289. // This is the default power-up mode which can be later using M605.
  290. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
  291. // Default settings in "Auto-park Mode"
  292. #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
  293. #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
  294. // Default x offset in duplication mode (typically set to half print bed width)
  295. #define DEFAULT_DUPLICATION_X_OFFSET 100
  296. #endif // DUAL_X_CARRIAGE
  297. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  298. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  299. //#define EXT_SOLENOID
  300. // @section homing
  301. //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
  302. #define X_HOME_BUMP_MM 5
  303. #define Y_HOME_BUMP_MM 5
  304. #define Z_HOME_BUMP_MM 2
  305. #define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  306. //#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
  307. // When G28 is called, this option will make Y home before X
  308. //#define HOME_Y_BEFORE_X
  309. // @section machine
  310. #define AXIS_RELATIVE_MODES {false, false, false, false}
  311. // Allow duplication mode with a basic dual-nozzle extruder
  312. //#define DUAL_NOZZLE_DUPLICATION_MODE
  313. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  314. #define INVERT_X_STEP_PIN false
  315. #define INVERT_Y_STEP_PIN false
  316. #define INVERT_Z_STEP_PIN false
  317. #define INVERT_E_STEP_PIN false
  318. // Default stepper release if idle. Set to 0 to deactivate.
  319. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
  320. // Time can be set by M18 and M84.
  321. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  322. #define DISABLE_INACTIVE_X true
  323. #define DISABLE_INACTIVE_Y true
  324. #define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
  325. #define DISABLE_INACTIVE_E true
  326. #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
  327. #define DEFAULT_MINTRAVELFEEDRATE 0.0
  328. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
  329. // @section lcd
  330. #if ENABLED(ULTIPANEL)
  331. #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
  332. #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
  333. #endif
  334. // @section extras
  335. // minimum time in microseconds that a movement needs to take if the buffer is emptied.
  336. #define DEFAULT_MINSEGMENTTIME 20000
  337. // If defined the movements slow down when the look ahead buffer is only half full
  338. #define SLOWDOWN
  339. // Frequency limit
  340. // See nophead's blog for more info
  341. // Not working O
  342. //#define XY_FREQUENCY_LIMIT 15
  343. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  344. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  345. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  346. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
  347. // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
  348. #define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
  349. /**
  350. * @section stepper motor current
  351. *
  352. * Some boards have a means of setting the stepper motor current via firmware.
  353. *
  354. * The power on motor currents are set by:
  355. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  356. * known compatible chips: A4982
  357. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  358. * known compatible chips: AD5206
  359. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  360. * known compatible chips: MCP4728
  361. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
  362. * known compatible chips: MCP4451, MCP4018
  363. *
  364. * Motor currents can also be set by M907 - M910 and by the LCD.
  365. * M907 - applies to all.
  366. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  367. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  368. */
  369. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  370. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  371. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  372. // Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
  373. //#define DIGIPOT_I2C
  374. //#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
  375. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
  376. // Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
  377. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  378. //===========================================================================
  379. //=============================Additional Features===========================
  380. //===========================================================================
  381. #define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
  382. #define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
  383. #define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
  384. //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  385. #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
  386. // @section lcd
  387. // Include a page of printer information in the LCD Main Menu
  388. //#define LCD_INFO_MENU
  389. // Scroll a longer status message into view
  390. //#define STATUS_MESSAGE_SCROLLING
  391. // On the Info Screen, display XY with one decimal place when possible
  392. //#define LCD_DECIMAL_SMALL_XY
  393. // The timeout (in ms) to return to the status screen from sub-menus
  394. //#define LCD_TIMEOUT_TO_STATUS 15000
  395. #if ENABLED(SDSUPPORT)
  396. // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
  397. // around this by connecting a push button or single throw switch to the pin defined
  398. // as SD_DETECT_PIN in your board's pins definitions.
  399. // This setting should be disabled unless you are using a push button, pulling the pin to ground.
  400. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
  401. #define SD_DETECT_INVERTED
  402. #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
  403. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
  404. #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
  405. // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
  406. // using:
  407. //#define MENU_ADDAUTOSTART
  408. /**
  409. * Sort SD file listings in alphabetical order.
  410. *
  411. * With this option enabled, items on SD cards will be sorted
  412. * by name for easier navigation.
  413. *
  414. * By default...
  415. *
  416. * - Use the slowest -but safest- method for sorting.
  417. * - Folders are sorted to the top.
  418. * - The sort key is statically allocated.
  419. * - No added G-code (M34) support.
  420. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  421. *
  422. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  423. * compiler to calculate the worst-case usage and throw an error if the SRAM
  424. * limit is exceeded.
  425. *
  426. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  427. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  428. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  429. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  430. */
  431. //#define SDCARD_SORT_ALPHA
  432. // SD Card Sorting options
  433. #if ENABLED(SDCARD_SORT_ALPHA)
  434. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  435. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  436. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
  437. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  438. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  439. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  440. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  441. #endif
  442. // Show a progress bar on HD44780 LCDs for SD printing
  443. //#define LCD_PROGRESS_BAR
  444. #if ENABLED(LCD_PROGRESS_BAR)
  445. // Amount of time (ms) to show the bar
  446. #define PROGRESS_BAR_BAR_TIME 2000
  447. // Amount of time (ms) to show the status message
  448. #define PROGRESS_BAR_MSG_TIME 3000
  449. // Amount of time (ms) to retain the status message (0=forever)
  450. #define PROGRESS_MSG_EXPIRE 0
  451. // Enable this to show messages for MSG_TIME then hide them
  452. //#define PROGRESS_MSG_ONCE
  453. // Add a menu item to test the progress bar:
  454. //#define LCD_PROGRESS_BAR_TEST
  455. #endif
  456. // This allows hosts to request long names for files and folders with M33
  457. //#define LONG_FILENAME_HOST_SUPPORT
  458. // This option allows you to abort SD printing when any endstop is triggered.
  459. // This feature must be enabled with "M540 S1" or from the LCD menu.
  460. // To have any effect, endstops must be enabled during SD printing.
  461. //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
  462. #endif // SDSUPPORT
  463. /**
  464. * Additional options for Graphical Displays
  465. *
  466. * Use the optimizations here to improve printing performance,
  467. * which can be adversely affected by graphical display drawing,
  468. * especially when doing several short moves, and when printing
  469. * on DELTA and SCARA machines.
  470. *
  471. * Some of these options may result in the display lagging behind
  472. * controller events, as there is a trade-off between reliable
  473. * printing performance versus fast display updates.
  474. */
  475. #if ENABLED(DOGLCD)
  476. // Enable to save many cycles by drawing a hollow frame on the Info Screen
  477. #define XYZ_HOLLOW_FRAME
  478. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  479. #define MENU_HOLLOW_FRAME
  480. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  481. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  482. //#define USE_BIG_EDIT_FONT
  483. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
  484. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  485. //#define USE_SMALL_INFOFONT
  486. // Enable this option and reduce the value to optimize screen updates.
  487. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  488. //#define DOGM_SPI_DELAY_US 5
  489. // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined.
  490. #if ENABLED(VIKI2) || ENABLED(miniVIKI)
  491. #define DOGLCD_SCK SCK_PIN
  492. #define DOGLCD_MOSI MOSI_PIN
  493. #endif
  494. #endif // DOGLCD
  495. // @section safety
  496. // The hardware watchdog should reset the microcontroller disabling all outputs,
  497. // in case the firmware gets stuck and doesn't do temperature regulation.
  498. #define USE_WATCHDOG
  499. #if ENABLED(USE_WATCHDOG)
  500. // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
  501. // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
  502. // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
  503. //#define WATCHDOG_RESET_MANUAL
  504. #endif
  505. // @section lcd
  506. /**
  507. * Babystepping enables movement of the axes by tiny increments without changing
  508. * the current position values. This feature is used primarily to adjust the Z
  509. * axis in the first layer of a print in real-time.
  510. *
  511. * Warning: Does not respect endstops!
  512. */
  513. //#define BABYSTEPPING
  514. #if ENABLED(BABYSTEPPING)
  515. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  516. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  517. #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
  518. //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
  519. //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  520. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  521. // Note: Extra time may be added to mitigate controller latency.
  522. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  523. //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
  524. #endif
  525. // @section extruder
  526. // extruder advance constant (s2/mm3)
  527. //
  528. // advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
  529. //
  530. // Hooke's law says: force = k * distance
  531. // Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
  532. // so: v ^ 2 is proportional to number of steps we advance the extruder
  533. //#define ADVANCE
  534. #if ENABLED(ADVANCE)
  535. #define EXTRUDER_ADVANCE_K .0
  536. #define D_FILAMENT 2.85
  537. #endif
  538. /**
  539. * Implementation of linear pressure control
  540. *
  541. * Assumption: advance = k * (delta velocity)
  542. * K=0 means advance disabled.
  543. * See Marlin documentation for calibration instructions.
  544. */
  545. //#define LIN_ADVANCE
  546. #if ENABLED(LIN_ADVANCE)
  547. #define LIN_ADVANCE_K 75
  548. /**
  549. * Some Slicers produce Gcode with randomly jumping extrusion widths occasionally.
  550. * For example within a 0.4mm perimeter it may produce a single segment of 0.05mm width.
  551. * While this is harmless for normal printing (the fluid nature of the filament will
  552. * close this very, very tiny gap), it throws off the LIN_ADVANCE pressure adaption.
  553. *
  554. * For this case LIN_ADVANCE_E_D_RATIO can be used to set the extrusion:distance ratio
  555. * to a fixed value. Note that using a fixed ratio will lead to wrong nozzle pressures
  556. * if the slicer is using variable widths or layer heights within one print!
  557. *
  558. * This option sets the default E:D ratio at startup. Use `M900` to override this value.
  559. *
  560. * Example: `M900 W0.4 H0.2 D1.75`, where:
  561. * - W is the extrusion width in mm
  562. * - H is the layer height in mm
  563. * - D is the filament diameter in mm
  564. *
  565. * Example: `M900 R0.0458` to set the ratio directly.
  566. *
  567. * Set to 0 to auto-detect the ratio based on given Gcode G1 print moves.
  568. *
  569. * Slic3r (including Průša Control) produces Gcode compatible with the automatic mode.
  570. * Cura (as of this writing) may produce Gcode incompatible with the automatic mode.
  571. */
  572. #define LIN_ADVANCE_E_D_RATIO 0 // The calculated ratio (or 0) according to the formula W * H / ((D / 2) ^ 2 * PI)
  573. // Example: 0.4 * 0.2 / ((1.75 / 2) ^ 2 * PI) = 0.033260135
  574. #endif
  575. // @section leveling
  576. // Default mesh area is an area with an inset margin on the print area.
  577. // Below are the macros that are used to define the borders for the mesh area,
  578. // made available here for specialized needs, ie dual extruder setup.
  579. #if ENABLED(MESH_BED_LEVELING)
  580. #define MESH_MIN_X MESH_INSET
  581. #define MESH_MAX_X (X_BED_SIZE - (MESH_INSET))
  582. #define MESH_MIN_Y MESH_INSET
  583. #define MESH_MAX_Y (Y_BED_SIZE - (MESH_INSET))
  584. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  585. #define UBL_MESH_MIN_X UBL_MESH_INSET
  586. #define UBL_MESH_MAX_X (X_BED_SIZE - (UBL_MESH_INSET))
  587. #define UBL_MESH_MIN_Y UBL_MESH_INSET
  588. #define UBL_MESH_MAX_Y (Y_BED_SIZE - (UBL_MESH_INSET))
  589. // If this is defined, the currently active mesh will be saved in the
  590. // current slot on M500.
  591. #define UBL_SAVE_ACTIVE_ON_M500
  592. #endif
  593. // @section extras
  594. //
  595. // G2/G3 Arc Support
  596. //
  597. #define ARC_SUPPORT // Disable this feature to save ~3226 bytes
  598. #if ENABLED(ARC_SUPPORT)
  599. #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
  600. #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
  601. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  602. //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
  603. #endif
  604. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  605. //#define BEZIER_CURVE_SUPPORT
  606. // G38.2 and G38.3 Probe Target
  607. // Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
  608. //#define G38_PROBE_TARGET
  609. #if ENABLED(G38_PROBE_TARGET)
  610. #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
  611. #endif
  612. // Moves (or segments) with fewer steps than this will be joined with the next move
  613. #define MIN_STEPS_PER_SEGMENT 6
  614. // The minimum pulse width (in µs) for stepping a stepper.
  615. // Set this if you find stepping unreliable, or if using a very fast CPU.
  616. #define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed
  617. // @section temperature
  618. // Control heater 0 and heater 1 in parallel.
  619. //#define HEATERS_PARALLEL
  620. //===========================================================================
  621. //================================= Buffers =================================
  622. //===========================================================================
  623. // @section hidden
  624. // The number of linear motions that can be in the plan at any give time.
  625. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
  626. #if ENABLED(SDSUPPORT)
  627. #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
  628. #else
  629. #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
  630. #endif
  631. // @section serial
  632. // The ASCII buffer for serial input
  633. #define MAX_CMD_SIZE 96
  634. #define BUFSIZE 4
  635. // Transfer Buffer Size
  636. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  637. // To buffer a simple "ok" you need 4 bytes.
  638. // For ADVANCED_OK (M105) you need 32 bytes.
  639. // For debug-echo: 128 bytes for the optimal speed.
  640. // Other output doesn't need to be that speedy.
  641. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  642. #define TX_BUFFER_SIZE 0
  643. // Enable an emergency-command parser to intercept certain commands as they
  644. // enter the serial receive buffer, so they cannot be blocked.
  645. // Currently handles M108, M112, M410
  646. // Does not work on boards using AT90USB (USBCON) processors!
  647. //#define EMERGENCY_PARSER
  648. // Bad Serial-connections can miss a received command by sending an 'ok'
  649. // Therefore some clients abort after 30 seconds in a timeout.
  650. // Some other clients start sending commands while receiving a 'wait'.
  651. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  652. //#define NO_TIMEOUTS 1000 // Milliseconds
  653. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  654. //#define ADVANCED_OK
  655. // @section extras
  656. /**
  657. * Firmware-based and LCD-controlled retract
  658. *
  659. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  660. * Use M207 and M208 to define parameters for retract / recover.
  661. *
  662. * Use M209 to enable or disable auto-retract.
  663. * With auto-retract enabled, all G1 E moves within the set range
  664. * will be converted to firmware-based retract/recover moves.
  665. *
  666. * Be sure to turn off auto-retract during filament change.
  667. *
  668. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  669. *
  670. */
  671. //#define FWRETRACT // ONLY PARTIALLY TESTED
  672. #if ENABLED(FWRETRACT)
  673. #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
  674. #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
  675. #define RETRACT_LENGTH 3 // Default retract length (positive mm)
  676. #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
  677. #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)
  678. #define RETRACT_ZLIFT 0 // Default retract Z-lift
  679. #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering)
  680. #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
  681. #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s)
  682. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s)
  683. #endif
  684. /**
  685. * Advanced Pause
  686. * Experimental feature for filament change support and for parking the nozzle when paused.
  687. * Adds the GCode M600 for initiating filament change.
  688. * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
  689. *
  690. * Requires an LCD display.
  691. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  692. */
  693. //#define ADVANCED_PAUSE_FEATURE
  694. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  695. #define PAUSE_PARK_X_POS 3 // X position of hotend
  696. #define PAUSE_PARK_Y_POS 3 // Y position of hotend
  697. #define PAUSE_PARK_Z_ADD 10 // Z addition of hotend (lift)
  698. #define PAUSE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  699. #define PAUSE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
  700. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
  701. #define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
  702. // It is a short retract used immediately after print interrupt before move to filament exchange position
  703. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
  704. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
  705. // Longer length for bowden printers to unload filament from whole bowden tube,
  706. // shorter length for printers without bowden to unload filament from extruder only,
  707. // 0 to disable unloading for manual unloading
  708. #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
  709. #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
  710. // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
  711. // Short or zero length for printers without bowden where loading is not used
  712. #define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
  713. #define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
  714. // 0 to disable for manual extrusion
  715. // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
  716. // or until outcoming filament color is not clear for filament color change
  717. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
  718. #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
  719. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
  720. // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
  721. //#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
  722. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
  723. #endif
  724. // @section tmc
  725. /**
  726. * Enable this section if you have TMC26X motor drivers.
  727. * You will need to import the TMC26XStepper library into the Arduino IDE for this
  728. * (https://github.com/trinamic/TMC26XStepper.git)
  729. */
  730. //#define HAVE_TMCDRIVER
  731. #if ENABLED(HAVE_TMCDRIVER)
  732. //#define X_IS_TMC
  733. //#define X2_IS_TMC
  734. //#define Y_IS_TMC
  735. //#define Y2_IS_TMC
  736. //#define Z_IS_TMC
  737. //#define Z2_IS_TMC
  738. //#define E0_IS_TMC
  739. //#define E1_IS_TMC
  740. //#define E2_IS_TMC
  741. //#define E3_IS_TMC
  742. //#define E4_IS_TMC
  743. #define X_MAX_CURRENT 1000 // in mA
  744. #define X_SENSE_RESISTOR 91 // in mOhms
  745. #define X_MICROSTEPS 16 // number of microsteps
  746. #define X2_MAX_CURRENT 1000
  747. #define X2_SENSE_RESISTOR 91
  748. #define X2_MICROSTEPS 16
  749. #define Y_MAX_CURRENT 1000
  750. #define Y_SENSE_RESISTOR 91
  751. #define Y_MICROSTEPS 16
  752. #define Y2_MAX_CURRENT 1000
  753. #define Y2_SENSE_RESISTOR 91
  754. #define Y2_MICROSTEPS 16
  755. #define Z_MAX_CURRENT 1000
  756. #define Z_SENSE_RESISTOR 91
  757. #define Z_MICROSTEPS 16
  758. #define Z2_MAX_CURRENT 1000
  759. #define Z2_SENSE_RESISTOR 91
  760. #define Z2_MICROSTEPS 16
  761. #define E0_MAX_CURRENT 1000
  762. #define E0_SENSE_RESISTOR 91
  763. #define E0_MICROSTEPS 16
  764. #define E1_MAX_CURRENT 1000
  765. #define E1_SENSE_RESISTOR 91
  766. #define E1_MICROSTEPS 16
  767. #define E2_MAX_CURRENT 1000
  768. #define E2_SENSE_RESISTOR 91
  769. #define E2_MICROSTEPS 16
  770. #define E3_MAX_CURRENT 1000
  771. #define E3_SENSE_RESISTOR 91
  772. #define E3_MICROSTEPS 16
  773. #define E4_MAX_CURRENT 1000
  774. #define E4_SENSE_RESISTOR 91
  775. #define E4_MICROSTEPS 16
  776. #endif
  777. // @section TMC2130
  778. /**
  779. * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
  780. *
  781. * You'll also need the TMC2130Stepper Arduino library
  782. * (https://github.com/teemuatlut/TMC2130Stepper).
  783. *
  784. * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
  785. * the hardware SPI interface on your board and define the required CS pins
  786. * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  787. */
  788. //#define HAVE_TMC2130
  789. #if ENABLED(HAVE_TMC2130)
  790. // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
  791. //#define X_IS_TMC2130
  792. //#define X2_IS_TMC2130
  793. //#define Y_IS_TMC2130
  794. //#define Y2_IS_TMC2130
  795. //#define Z_IS_TMC2130
  796. //#define Z2_IS_TMC2130
  797. //#define E0_IS_TMC2130
  798. //#define E1_IS_TMC2130
  799. //#define E2_IS_TMC2130
  800. //#define E3_IS_TMC2130
  801. //#define E4_IS_TMC2130
  802. /**
  803. * Stepper driver settings
  804. */
  805. #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
  806. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  807. #define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
  808. #define X_CURRENT 1000 // rms current in mA. Multiply by 1.41 for peak current.
  809. #define X_MICROSTEPS 16 // 0..256
  810. #define Y_CURRENT 1000
  811. #define Y_MICROSTEPS 16
  812. #define Z_CURRENT 1000
  813. #define Z_MICROSTEPS 16
  814. //#define X2_CURRENT 1000
  815. //#define X2_MICROSTEPS 16
  816. //#define Y2_CURRENT 1000
  817. //#define Y2_MICROSTEPS 16
  818. //#define Z2_CURRENT 1000
  819. //#define Z2_MICROSTEPS 16
  820. //#define E0_CURRENT 1000
  821. //#define E0_MICROSTEPS 16
  822. //#define E1_CURRENT 1000
  823. //#define E1_MICROSTEPS 16
  824. //#define E2_CURRENT 1000
  825. //#define E2_MICROSTEPS 16
  826. //#define E3_CURRENT 1000
  827. //#define E3_MICROSTEPS 16
  828. //#define E4_CURRENT 1000
  829. //#define E4_MICROSTEPS 16
  830. /**
  831. * Use Trinamic's ultra quiet stepping mode.
  832. * When disabled, Marlin will use spreadCycle stepping mode.
  833. */
  834. #define STEALTHCHOP
  835. /**
  836. * Let Marlin automatically control stepper current.
  837. * This is still an experimental feature.
  838. * Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
  839. * then decrease current by CURRENT_STEP until temperature prewarn is cleared.
  840. * Adjusting starts from X/Y/Z/E_CURRENT but will not increase over AUTO_ADJUST_MAX
  841. * Relevant g-codes:
  842. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  843. * M906 S1 - Start adjusting current
  844. * M906 S0 - Stop adjusting current
  845. * M911 - Report stepper driver overtemperature pre-warn condition.
  846. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  847. */
  848. //#define AUTOMATIC_CURRENT_CONTROL
  849. #if ENABLED(AUTOMATIC_CURRENT_CONTROL)
  850. #define CURRENT_STEP 50 // [mA]
  851. #define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
  852. #define REPORT_CURRENT_CHANGE
  853. #endif
  854. /**
  855. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  856. * This mode allows for faster movements at the expense of higher noise levels.
  857. * STEALTHCHOP needs to be enabled.
  858. * M913 X/Y/Z/E to live tune the setting
  859. */
  860. //#define HYBRID_THRESHOLD
  861. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  862. #define X2_HYBRID_THRESHOLD 100
  863. #define Y_HYBRID_THRESHOLD 100
  864. #define Y2_HYBRID_THRESHOLD 100
  865. #define Z_HYBRID_THRESHOLD 4
  866. #define Z2_HYBRID_THRESHOLD 4
  867. #define E0_HYBRID_THRESHOLD 30
  868. #define E1_HYBRID_THRESHOLD 30
  869. #define E2_HYBRID_THRESHOLD 30
  870. #define E3_HYBRID_THRESHOLD 30
  871. #define E4_HYBRID_THRESHOLD 30
  872. /**
  873. * Use stallGuard2 to sense an obstacle and trigger an endstop.
  874. * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
  875. * If used along with STEALTHCHOP, the movement will be louder when homing. This is normal.
  876. *
  877. * X/Y_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
  878. * Higher values make the system LESS sensitive.
  879. * Lower value make the system MORE sensitive.
  880. * Too low values can lead to false positives, while too high values will collide the axis without triggering.
  881. * It is advised to set X/Y_HOME_BUMP_MM to 0.
  882. * M914 X/Y to live tune the setting
  883. */
  884. //#define SENSORLESS_HOMING
  885. #if ENABLED(SENSORLESS_HOMING)
  886. #define X_HOMING_SENSITIVITY 19
  887. #define Y_HOMING_SENSITIVITY 19
  888. #endif
  889. /**
  890. * You can set your own advanced settings by filling in predefined functions.
  891. * A list of available functions can be found on the library github page
  892. * https://github.com/teemuatlut/TMC2130Stepper
  893. *
  894. * Example:
  895. * #define TMC2130_ADV() { \
  896. * stepperX.diag0_temp_prewarn(1); \
  897. * stepperX.interpolate(0); \
  898. * }
  899. */
  900. #define TMC2130_ADV() { }
  901. #endif // HAVE_TMC2130
  902. // @section L6470
  903. /**
  904. * Enable this section if you have L6470 motor drivers.
  905. * You need to import the L6470 library into the Arduino IDE for this.
  906. * (https://github.com/ameyer/Arduino-L6470)
  907. */
  908. //#define HAVE_L6470DRIVER
  909. #if ENABLED(HAVE_L6470DRIVER)
  910. //#define X_IS_L6470
  911. //#define X2_IS_L6470
  912. //#define Y_IS_L6470
  913. //#define Y2_IS_L6470
  914. //#define Z_IS_L6470
  915. //#define Z2_IS_L6470
  916. //#define E0_IS_L6470
  917. //#define E1_IS_L6470
  918. //#define E2_IS_L6470
  919. //#define E3_IS_L6470
  920. //#define E4_IS_L6470
  921. #define X_MICROSTEPS 16 // number of microsteps
  922. #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
  923. #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
  924. #define X2_MICROSTEPS 16
  925. #define X2_OVERCURRENT 2000
  926. #define X2_STALLCURRENT 1500
  927. #define Y_MICROSTEPS 16
  928. #define Y_OVERCURRENT 2000
  929. #define Y_STALLCURRENT 1500
  930. #define Y2_MICROSTEPS 16
  931. #define Y2_OVERCURRENT 2000
  932. #define Y2_STALLCURRENT 1500
  933. #define Z_MICROSTEPS 16
  934. #define Z_OVERCURRENT 2000
  935. #define Z_STALLCURRENT 1500
  936. #define Z2_MICROSTEPS 16
  937. #define Z2_OVERCURRENT 2000
  938. #define Z2_STALLCURRENT 1500
  939. #define E0_MICROSTEPS 16
  940. #define E0_OVERCURRENT 2000
  941. #define E0_STALLCURRENT 1500
  942. #define E1_MICROSTEPS 16
  943. #define E1_OVERCURRENT 2000
  944. #define E1_STALLCURRENT 1500
  945. #define E2_MICROSTEPS 16
  946. #define E2_OVERCURRENT 2000
  947. #define E2_STALLCURRENT 1500
  948. #define E3_MICROSTEPS 16
  949. #define E3_OVERCURRENT 2000
  950. #define E3_STALLCURRENT 1500
  951. #define E4_MICROSTEPS 16
  952. #define E4_OVERCURRENT 2000
  953. #define E4_STALLCURRENT 1500
  954. #endif
  955. /**
  956. * TWI/I2C BUS
  957. *
  958. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  959. * machines. Enabling this will allow you to send and receive I2C data from slave
  960. * devices on the bus.
  961. *
  962. * ; Example #1
  963. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  964. * ; It uses multiple M260 commands with one B<base 10> arg
  965. * M260 A99 ; Target slave address
  966. * M260 B77 ; M
  967. * M260 B97 ; a
  968. * M260 B114 ; r
  969. * M260 B108 ; l
  970. * M260 B105 ; i
  971. * M260 B110 ; n
  972. * M260 S1 ; Send the current buffer
  973. *
  974. * ; Example #2
  975. * ; Request 6 bytes from slave device with address 0x63 (99)
  976. * M261 A99 B5
  977. *
  978. * ; Example #3
  979. * ; Example serial output of a M261 request
  980. * echo:i2c-reply: from:99 bytes:5 data:hello
  981. */
  982. // @section i2cbus
  983. //#define EXPERIMENTAL_I2CBUS
  984. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  985. // @section extras
  986. /**
  987. * Spindle & Laser control
  988. *
  989. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  990. * to set spindle speed, spindle direction, and laser power.
  991. *
  992. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  993. * Marlin can be used to turn the spindle on and off. It can also be used to set
  994. * the spindle speed from 5,000 to 30,000 RPM.
  995. *
  996. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  997. * hardware PWM pin for the speed control and a pin for the rotation direction.
  998. *
  999. * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  1000. */
  1001. //#define SPINDLE_LASER_ENABLE
  1002. #if ENABLED(SPINDLE_LASER_ENABLE)
  1003. #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
  1004. #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
  1005. #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
  1006. #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
  1007. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
  1008. #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
  1009. #define SPINDLE_INVERT_DIR false
  1010. #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
  1011. /**
  1012. * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
  1013. *
  1014. * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
  1015. * where PWM duty cycle varies from 0 to 255
  1016. *
  1017. * set the following for your controller (ALL MUST BE SET)
  1018. */
  1019. #define SPEED_POWER_SLOPE 118.4
  1020. #define SPEED_POWER_INTERCEPT 0
  1021. #define SPEED_POWER_MIN 5000
  1022. #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
  1023. //#define SPEED_POWER_SLOPE 0.3922
  1024. //#define SPEED_POWER_INTERCEPT 0
  1025. //#define SPEED_POWER_MIN 10
  1026. //#define SPEED_POWER_MAX 100 // 0-100%
  1027. #endif
  1028. /**
  1029. * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
  1030. */
  1031. //#define PINS_DEBUGGING
  1032. /**
  1033. * Auto-report temperatures with M155 S<seconds>
  1034. */
  1035. #define AUTO_REPORT_TEMPERATURES
  1036. /**
  1037. * Include capabilities in M115 output
  1038. */
  1039. #define EXTENDED_CAPABILITIES_REPORT
  1040. /**
  1041. * Volumetric extrusion default state
  1042. * Activate to make volumetric extrusion the default method,
  1043. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  1044. *
  1045. * M200 D0 to disable, M200 Dn to set a new diameter.
  1046. */
  1047. //#define VOLUMETRIC_DEFAULT_ON
  1048. /**
  1049. * Enable this option for a leaner build of Marlin that removes all
  1050. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  1051. *
  1052. * - M206 and M428 are disabled.
  1053. * - G92 will revert to its behavior from Marlin 1.0.
  1054. */
  1055. //#define NO_WORKSPACE_OFFSETS
  1056. /**
  1057. * Set the number of proportional font spaces required to fill up a typical character space.
  1058. * This can help to better align the output of commands like `G29 O` Mesh Output.
  1059. *
  1060. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  1061. * Otherwise, adjust according to your client and font.
  1062. */
  1063. #define PROPORTIONAL_FONT_RATIO 1.0
  1064. /**
  1065. * Spend 28 bytes of SRAM to optimize the GCode parser
  1066. */
  1067. #define FASTER_GCODE_PARSER
  1068. /**
  1069. * User-defined menu items that execute custom GCode
  1070. */
  1071. //#define CUSTOM_USER_MENUS
  1072. #if ENABLED(CUSTOM_USER_MENUS)
  1073. #define USER_SCRIPT_DONE "M117 User Script Done"
  1074. #define USER_SCRIPT_AUDIBLE_FEEDBACK
  1075. #define USER_DESC_1 "Home & UBL Info"
  1076. #define USER_GCODE_1 "G28\nG29 W"
  1077. #define USER_DESC_2 "Preheat for PLA"
  1078. #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  1079. #define USER_DESC_3 "Preheat for ABS"
  1080. #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  1081. #define USER_DESC_4 "Heat Bed/Home/Level"
  1082. #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  1083. #define USER_DESC_5 "Home & Info"
  1084. #define USER_GCODE_5 "G28\nM503"
  1085. #endif
  1086. /**
  1087. * Specify an action command to send to the host when the printer is killed.
  1088. * Will be sent in the form '//action:ACTION_ON_KILL', e.g. '//action:poweroff'.
  1089. * The host must be configured to handle the action command.
  1090. */
  1091. //#define ACTION_ON_KILL "poweroff"
  1092. //===========================================================================
  1093. //====================== I2C Position Encoder Settings ======================
  1094. //===========================================================================
  1095. /**
  1096. * I2C position encoders for closed loop control.
  1097. * Developed by Chris Barr at Aus3D.
  1098. *
  1099. * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
  1100. * Github: https://github.com/Aus3D/MagneticEncoder
  1101. *
  1102. * Supplier: http://aus3d.com.au/magnetic-encoder-module
  1103. * Alternative Supplier: http://reliabuild3d.com/
  1104. *
  1105. * Reilabuild encoders have been modified to improve reliability.
  1106. */
  1107. //#define I2C_POSITION_ENCODERS
  1108. #if ENABLED(I2C_POSITION_ENCODERS)
  1109. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  1110. // encoders supported currently.
  1111. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  1112. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  1113. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  1114. // I2CPE_ENC_TYPE_ROTARY.
  1115. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  1116. // 1mm poles. For linear encoders this is ticks / mm,
  1117. // for rotary encoders this is ticks / revolution.
  1118. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  1119. // steps per full revolution (motor steps/rev * microstepping)
  1120. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  1121. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_NONE // Type of error error correction.
  1122. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  1123. // printer will attempt to correct the error; errors
  1124. // smaller than this are ignored to minimize effects of
  1125. // measurement noise / latency (filter).
  1126. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  1127. #define I2CPE_ENC_2_AXIS Y_AXIS
  1128. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  1129. #define I2CPE_ENC_2_TICKS_UNIT 2048
  1130. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  1131. //#define I2CPE_ENC_2_INVERT
  1132. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_NONE
  1133. #define I2CPE_ENC_2_EC_THRESH 0.10
  1134. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  1135. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  1136. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  1137. #define I2CPE_ENC_4_AXIS E_AXIS
  1138. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  1139. #define I2CPE_ENC_5_AXIS E_AXIS
  1140. // Default settings for encoders which are enabled, but without settings configured above.
  1141. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  1142. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  1143. #define I2CPE_DEF_TICKS_REV (16 * 200)
  1144. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  1145. #define I2CPE_DEF_EC_THRESH 0.1
  1146. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  1147. // axis after which the printer will abort. Comment out to
  1148. // disable abort behaviour.
  1149. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  1150. // for this amount of time (in ms) before the encoder
  1151. // is trusted again.
  1152. /**
  1153. * Position is checked every time a new command is executed from the buffer but during long moves,
  1154. * this setting determines the minimum update time between checks. A value of 100 works well with
  1155. * error rolling average when attempting to correct only for skips and not for vibration.
  1156. */
  1157. #define I2CPE_MIN_UPD_TIME_MS 100 // Minimum time in miliseconds between encoder checks.
  1158. // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
  1159. #define I2CPE_ERR_ROLLING_AVERAGE
  1160. #endif // I2C_POSITION_ENCODERS
  1161. /**
  1162. * MAX7219 Debug Matrix
  1163. *
  1164. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip, which can be used as a status
  1165. * display. Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  1166. *
  1167. * Fully assembled MAX7219 boards can be found on the internet for under $2(US).
  1168. * For example, see https://www.ebay.com/sch/i.html?_nkw=332349290049
  1169. */
  1170. //#define MAX7219_DEBUG
  1171. #if ENABLED(MAX7219_DEBUG)
  1172. #define MAX7219_CLK_PIN 64 // 77 on Re-ARM // Configuration of the 3 pins to control the display
  1173. #define MAX7219_DIN_PIN 57 // 78 on Re-ARM
  1174. #define MAX7219_LOAD_PIN 44 // 79 on Re-ARM
  1175. /**
  1176. * Sample debug features
  1177. * If you add more debug displays, be careful to avoid conflicts!
  1178. */
  1179. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  1180. #define MAX7219_DEBUG_STEPPER_HEAD 3 // Show the stepper queue head position on this and the next LED matrix row
  1181. #define MAX7219_DEBUG_STEPPER_TAIL 5 // Show the stepper queue tail position on this and the next LED matrix row
  1182. #define MAX7219_DEBUG_STEPPER_QUEUE 0 // Show the current stepper queue depth on this and the next LED matrix row
  1183. // If you experience stuttering, reboots, etc. this option can reveal how
  1184. // tweaks made to the configuration are affecting the printer in real-time.
  1185. #endif
  1186. #endif // CONFIGURATION_ADV_H