My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Nevar pievienot vairāk kā 25 tēmas Tēmai ir jāsākas ar burtu vai ciparu, tā var saturēt domu zīmes ('-') un var būt līdz 35 simboliem gara.

Configuration.h 82KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397139813991400140114021403140414051406140714081409141014111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472147314741475147614771478147914801481148214831484148514861487148814891490149114921493149414951496149714981499150015011502150315041505150615071508150915101511151215131514151515161517151815191520152115221523152415251526152715281529153015311532153315341535153615371538153915401541154215431544154515461547154815491550155115521553155415551556155715581559156015611562156315641565156615671568156915701571157215731574157515761577157815791580158115821583158415851586158715881589159015911592159315941595159615971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628162916301631163216331634163516361637163816391640164116421643164416451646164716481649165016511652165316541655165616571658165916601661166216631664166516661667166816691670167116721673167416751676167716781679168016811682168316841685168616871688168916901691169216931694169516961697169816991700170117021703170417051706170717081709171017111712171317141715171617171718171917201721172217231724172517261727172817291730173117321733173417351736173717381739174017411742174317441745174617471748174917501751175217531754175517561757175817591760176117621763176417651766176717681769177017711772177317741775177617771778177917801781178217831784178517861787178817891790179117921793179417951796179717981799180018011802180318041805180618071808180918101811181218131814181518161817181818191820182118221823182418251826182718281829183018311832183318341835183618371838183918401841184218431844184518461847184818491850185118521853185418551856185718581859186018611862186318641865186618671868186918701871187218731874187518761877187818791880188118821883188418851886188718881889189018911892189318941895189618971898189919001901190219031904190519061907190819091910191119121913191419151916191719181919192019211922192319241925192619271928192919301931193219331934193519361937193819391940194119421943194419451946194719481949195019511952195319541955195619571958195919601961196219631964196519661967196819691970197119721973197419751976197719781979198019811982198319841985198619871988198919901991199219931994199519961997199819992000200120022003200420052006200720082009201020112012201320142015201620172018201920202021202220232024202520262027202820292030203120322033203420352036203720382039204020412042204320442045204620472048204920502051205220532054205520562057205820592060206120622063206420652066206720682069207020712072207320742075207620772078207920802081208220832084208520862087208820892090209120922093209420952096209720982099210021012102210321042105210621072108210921102111211221132114211521162117211821192120212121222123212421252126212721282129213021312132213321342135213621372138213921402141214221432144214521462147214821492150215121522153215421552156215721582159216021612162216321642165216621672168216921702171217221732174217521762177217821792180218121822183218421852186218721882189219021912192219321942195219621972198219922002201220222032204220522062207220822092210221122122213221422152216221722182219222022212222222322242225222622272228222922302231223222332234223522362237223822392240224122422243224422452246224722482249225022512252225322542255225622572258225922602261226222632264226522662267226822692270227122722273227422752276227722782279228022812282228322842285228622872288228922902291229222932294229522962297229822992300230123022303230423052306230723082309231023112312231323142315231623172318231923202321232223232324
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(Ralf_E, ANET A6 config)" // Who made the changes.
  68. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  69. /**
  70. * *** VENDORS PLEASE READ ***
  71. *
  72. * Marlin allows you to add a custom boot image for Graphical LCDs.
  73. * With this option Marlin will first show your custom screen followed
  74. * by the standard Marlin logo with version number and web URL.
  75. *
  76. * We encourage you to take advantage of this new feature and we also
  77. * respectfully request that you retain the unmodified Marlin boot screen.
  78. */
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  82. //#define SHOW_CUSTOM_BOOTSCREEN
  83. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  84. //#define CUSTOM_STATUS_SCREEN_IMAGE
  85. // @section machine
  86. /**
  87. * Select the serial port on the board to use for communication with the host.
  88. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  97. * Serial port -1 is the USB emulated serial port, if available.
  98. *
  99. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  100. */
  101. //#define SERIAL_PORT_2 -1
  102. /**
  103. * This setting determines the communication speed of the printer.
  104. *
  105. * 250000 works in most cases, but you might try a lower speed if
  106. * you commonly experience drop-outs during host printing.
  107. * You may try up to 1000000 to speed up SD file transfer.
  108. *
  109. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  110. */
  111. #define BAUDRATE 115200
  112. // Enable the Bluetooth serial interface on AT90USB devices
  113. //#define BLUETOOTH
  114. // Choose the name from boards.h that matches your setup
  115. #ifndef MOTHERBOARD
  116. #define MOTHERBOARD BOARD_ANET_10
  117. #endif
  118. // Name displayed in the LCD "Ready" message and Info menu
  119. #define CUSTOM_MACHINE_NAME "Anet A6"
  120. // Printer's unique ID, used by some programs to differentiate between machines.
  121. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  122. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  123. // @section extruder
  124. // This defines the number of extruders
  125. // :[1, 2, 3, 4, 5, 6]
  126. #define EXTRUDERS 1
  127. // The Anet A6 original extruder is designed for 1.75mm
  128. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  129. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  130. //#define SINGLENOZZLE
  131. /**
  132. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  133. *
  134. * This device allows one stepper driver on a control board to drive
  135. * two to eight stepper motors, one at a time, in a manner suitable
  136. * for extruders.
  137. *
  138. * This option only allows the multiplexer to switch on tool-change.
  139. * Additional options to configure custom E moves are pending.
  140. */
  141. //#define MK2_MULTIPLEXER
  142. #if ENABLED(MK2_MULTIPLEXER)
  143. // Override the default DIO selector pins here, if needed.
  144. // Some pins files may provide defaults for these pins.
  145. //#define E_MUX0_PIN 40 // Always Required
  146. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  147. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  148. #endif
  149. /**
  150. * Prusa Multi-Material Unit v2
  151. *
  152. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  153. * Requires EXTRUDERS = 5
  154. *
  155. * For additional configuration see Configuration_adv.h
  156. */
  157. //#define PRUSA_MMU2
  158. // A dual extruder that uses a single stepper motor
  159. //#define SWITCHING_EXTRUDER
  160. #if ENABLED(SWITCHING_EXTRUDER)
  161. #define SWITCHING_EXTRUDER_SERVO_NR 0
  162. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  163. #if EXTRUDERS > 3
  164. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  165. #endif
  166. #endif
  167. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  168. //#define SWITCHING_NOZZLE
  169. #if ENABLED(SWITCHING_NOZZLE)
  170. #define SWITCHING_NOZZLE_SERVO_NR 0
  171. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  172. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  173. #endif
  174. /**
  175. * Two separate X-carriages with extruders that connect to a moving part
  176. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  177. */
  178. //#define PARKING_EXTRUDER
  179. /**
  180. * Two separate X-carriages with extruders that connect to a moving part
  181. * via a magnetic docking mechanism using movements and no solenoid
  182. *
  183. * project : https://www.thingiverse.com/thing:3080893
  184. * movements : https://youtu.be/0xCEiG9VS3k
  185. * https://youtu.be/Bqbcs0CU2FE
  186. */
  187. //#define MAGNETIC_PARKING_EXTRUDER
  188. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  189. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  190. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  191. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  192. #if ENABLED(PARKING_EXTRUDER)
  193. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  194. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  195. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  196. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  197. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  198. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  199. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  200. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  201. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  202. #endif
  203. #endif
  204. /**
  205. * Switching Toolhead
  206. *
  207. * Support for swappable and dockable toolheads, such as
  208. * the E3D Tool Changer. Toolheads are locked with a servo.
  209. */
  210. //#define SWITCHING_TOOLHEAD
  211. /**
  212. * Magnetic Switching Toolhead
  213. *
  214. * Support swappable and dockable toolheads with a magnetic
  215. * docking mechanism using movement and no servo.
  216. */
  217. //#define MAGNETIC_SWITCHING_TOOLHEAD
  218. /**
  219. * Electromagnetic Switching Toolhead
  220. *
  221. * Parking for CoreXY / HBot kinematics.
  222. * Toolheads are parked at one edge and held with an electromagnet.
  223. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  224. */
  225. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  226. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  227. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  228. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  229. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  230. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  231. #if ENABLED(SWITCHING_TOOLHEAD)
  232. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  233. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  234. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  235. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  236. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  237. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  238. #if ENABLED(PRIME_BEFORE_REMOVE)
  239. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  240. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  241. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  242. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  243. #endif
  244. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  245. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  246. #endif
  247. #endif
  248. /**
  249. * "Mixing Extruder"
  250. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  251. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  252. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  253. * - This implementation supports up to two mixing extruders.
  254. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  255. */
  256. //#define MIXING_EXTRUDER
  257. #if ENABLED(MIXING_EXTRUDER)
  258. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  259. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  260. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  261. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  262. #if ENABLED(GRADIENT_MIX)
  263. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  264. #endif
  265. #endif
  266. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  267. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  268. // For the other hotends it is their distance from the extruder 0 hotend.
  269. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  270. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  271. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  272. // @section machine
  273. /**
  274. * Power Supply Control
  275. *
  276. * Enable and connect the power supply to the PS_ON_PIN.
  277. * Specify whether the power supply is active HIGH or active LOW.
  278. */
  279. //#define PSU_CONTROL
  280. //#define PSU_NAME "Power Supply"
  281. #if ENABLED(PSU_CONTROL)
  282. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
  283. //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80
  284. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  285. #if ENABLED(AUTO_POWER_CONTROL)
  286. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  287. #define AUTO_POWER_E_FANS
  288. #define AUTO_POWER_CONTROLLERFAN
  289. #define AUTO_POWER_CHAMBER_FAN
  290. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  291. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  292. #define POWER_TIMEOUT 30
  293. #endif
  294. #endif
  295. // @section temperature
  296. //===========================================================================
  297. //============================= Thermal Settings ============================
  298. //===========================================================================
  299. /**
  300. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  301. *
  302. * Temperature sensors available:
  303. *
  304. * -4 : thermocouple with AD8495
  305. * -3 : thermocouple with MAX31855 (only for sensor 0)
  306. * -2 : thermocouple with MAX6675 (only for sensor 0)
  307. * -1 : thermocouple with AD595
  308. * 0 : not used
  309. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  310. * 331 : (3.3V scaled thermistor 1 table)
  311. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  312. * 3 : Mendel-parts thermistor (4.7k pullup)
  313. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  314. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  315. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  316. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  317. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  318. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  319. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  320. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  321. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  322. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  323. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  324. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  325. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  326. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  327. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  328. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  329. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  330. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  331. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  332. * 66 : 4.7M High Temperature thermistor from Dyze Design
  333. * 67 : 450C thermistor from SliceEngineering
  334. * 70 : the 100K thermistor found in the bq Hephestos 2
  335. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  336. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  337. *
  338. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  339. * (but gives greater accuracy and more stable PID)
  340. * 51 : 100k thermistor - EPCOS (1k pullup)
  341. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  342. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  343. *
  344. * 1047 : Pt1000 with 4k7 pullup
  345. * 1010 : Pt1000 with 1k pullup (non standard)
  346. * 147 : Pt100 with 4k7 pullup
  347. * 110 : Pt100 with 1k pullup (non standard)
  348. *
  349. * 1000 : Custom - Specify parameters in Configuration_adv.h
  350. *
  351. * Use these for Testing or Development purposes. NEVER for production machine.
  352. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  353. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  354. */
  355. #define TEMP_SENSOR_0 11
  356. #define TEMP_SENSOR_1 0
  357. #define TEMP_SENSOR_2 0
  358. #define TEMP_SENSOR_3 0
  359. #define TEMP_SENSOR_4 0
  360. #define TEMP_SENSOR_5 0
  361. #define TEMP_SENSOR_BED 11
  362. #define TEMP_SENSOR_CHAMBER 0
  363. // Dummy thermistor constant temperature readings, for use with 998 and 999
  364. #define DUMMY_THERMISTOR_998_VALUE 25
  365. #define DUMMY_THERMISTOR_999_VALUE 100
  366. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  367. // from the two sensors differ too much the print will be aborted.
  368. //#define TEMP_SENSOR_1_AS_REDUNDANT
  369. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  370. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  371. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  372. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  373. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  374. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  375. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  376. // Below this temperature the heater will be switched off
  377. // because it probably indicates a broken thermistor wire.
  378. #define HEATER_0_MINTEMP 5
  379. #define HEATER_1_MINTEMP 5
  380. #define HEATER_2_MINTEMP 5
  381. #define HEATER_3_MINTEMP 5
  382. #define HEATER_4_MINTEMP 5
  383. #define HEATER_5_MINTEMP 5
  384. #define BED_MINTEMP 5
  385. // Above this temperature the heater will be switched off.
  386. // This can protect components from overheating, but NOT from shorts and failures.
  387. // (Use MINTEMP for thermistor short/failure protection.)
  388. #define HEATER_0_MAXTEMP 275
  389. #define HEATER_1_MAXTEMP 275
  390. #define HEATER_2_MAXTEMP 275
  391. #define HEATER_3_MAXTEMP 275
  392. #define HEATER_4_MAXTEMP 275
  393. #define HEATER_5_MAXTEMP 275
  394. #define BED_MAXTEMP 130
  395. //===========================================================================
  396. //============================= PID Settings ================================
  397. //===========================================================================
  398. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  399. // Comment the following line to disable PID and enable bang-bang.
  400. #define PIDTEMP
  401. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  402. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  403. #define PID_K1 0.95 // Smoothing factor within any PID loop
  404. #if ENABLED(PIDTEMP)
  405. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  406. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  407. //#define PID_DEBUG // Sends debug data to the serial port.
  408. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  409. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  410. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  411. // Set/get with gcode: M301 E[extruder number, 0-2]
  412. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  413. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  414. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  415. // Ultimaker
  416. //#define DEFAULT_Kp 22.2
  417. //#define DEFAULT_Ki 1.08
  418. //#define DEFAULT_Kd 114
  419. // MakerGear
  420. //#define DEFAULT_Kp 7.0
  421. //#define DEFAULT_Ki 0.1
  422. //#define DEFAULT_Kd 12
  423. // Mendel Parts V9 on 12V
  424. //#define DEFAULT_Kp 63.0
  425. //#define DEFAULT_Ki 2.25
  426. //#define DEFAULT_Kd 440
  427. // ANET A6 Firmware V2.0 Standard Extruder defaults:
  428. // PID-P: +022.20, PID-I: +001.08, PID-D: +114.00, PID-C: 1
  429. //#define DEFAULT_Kp 22.2
  430. //#define DEFAULT_Ki 1.08
  431. //#define DEFAULT_Kd 114.0
  432. // Tuned by ralf-e. Always re-tune for your machine!
  433. #define DEFAULT_Kp 16.83
  434. #define DEFAULT_Ki 1.02
  435. #define DEFAULT_Kd 69.29
  436. #endif // PIDTEMP
  437. //===========================================================================
  438. //====================== PID > Bed Temperature Control ======================
  439. //===========================================================================
  440. /**
  441. * PID Bed Heating
  442. *
  443. * If this option is enabled set PID constants below.
  444. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  445. *
  446. * The PID frequency will be the same as the extruder PWM.
  447. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  448. * which is fine for driving a square wave into a resistive load and does not significantly
  449. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  450. * heater. If your configuration is significantly different than this and you don't understand
  451. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  452. */
  453. #define PIDTEMPBED
  454. //#define BED_LIMIT_SWITCHING
  455. /**
  456. * Max Bed Power
  457. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  458. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  459. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  460. */
  461. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  462. #if ENABLED(PIDTEMPBED)
  463. //#define MIN_BED_POWER 0
  464. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  465. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  466. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  467. //#define DEFAULT_bedKp 10.00
  468. //#define DEFAULT_bedKi .023
  469. //#define DEFAULT_bedKd 305.4
  470. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  471. //from pidautotune
  472. //#define DEFAULT_bedKp 97.1
  473. //#define DEFAULT_bedKi 1.41
  474. //#define DEFAULT_bedKd 1675.16
  475. // ANET A6
  476. // original Bed + 0.3mm Heat conducting into 4mm borosilicate (PID-Autotune: M303 E-1 S60 C5):
  477. //#define DEFAULT_bedKp 295.00
  478. //#define DEFAULT_bedKi 35.65
  479. //#define DEFAULT_bedKd 610.21
  480. #define DEFAULT_bedKp 295.00
  481. #define DEFAULT_bedKi 35.65
  482. #define DEFAULT_bedKd 610.21
  483. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  484. #endif // PIDTEMPBED
  485. // @section extruder
  486. /**
  487. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  488. * Add M302 to set the minimum extrusion temperature and/or turn
  489. * cold extrusion prevention on and off.
  490. *
  491. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  492. */
  493. #define PREVENT_COLD_EXTRUSION
  494. #define EXTRUDE_MINTEMP 170
  495. /**
  496. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  497. * Note: For Bowden Extruders make this large enough to allow load/unload.
  498. */
  499. #define PREVENT_LENGTHY_EXTRUDE
  500. #define EXTRUDE_MAXLENGTH 200
  501. //===========================================================================
  502. //======================== Thermal Runaway Protection =======================
  503. //===========================================================================
  504. /**
  505. * Thermal Protection provides additional protection to your printer from damage
  506. * and fire. Marlin always includes safe min and max temperature ranges which
  507. * protect against a broken or disconnected thermistor wire.
  508. *
  509. * The issue: If a thermistor falls out, it will report the much lower
  510. * temperature of the air in the room, and the the firmware will keep
  511. * the heater on.
  512. *
  513. * If you get "Thermal Runaway" or "Heating failed" errors the
  514. * details can be tuned in Configuration_adv.h
  515. */
  516. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  517. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  518. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  519. //===========================================================================
  520. //============================= Mechanical Settings =========================
  521. //===========================================================================
  522. // @section machine
  523. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  524. // either in the usual order or reversed
  525. //#define COREXY
  526. //#define COREXZ
  527. //#define COREYZ
  528. //#define COREYX
  529. //#define COREZX
  530. //#define COREZY
  531. //===========================================================================
  532. //============================== Endstop Settings ===========================
  533. //===========================================================================
  534. // @section homing
  535. // Specify here all the endstop connectors that are connected to any endstop or probe.
  536. // Almost all printers will be using one per axis. Probes will use one or more of the
  537. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  538. #define USE_XMIN_PLUG
  539. #define USE_YMIN_PLUG
  540. #define USE_ZMIN_PLUG
  541. //#define USE_XMAX_PLUG
  542. //#define USE_YMAX_PLUG
  543. //#define USE_ZMAX_PLUG
  544. // Enable pullup for all endstops to prevent a floating state
  545. #define ENDSTOPPULLUPS
  546. #if DISABLED(ENDSTOPPULLUPS)
  547. // Disable ENDSTOPPULLUPS to set pullups individually
  548. //#define ENDSTOPPULLUP_XMAX
  549. //#define ENDSTOPPULLUP_YMAX
  550. //#define ENDSTOPPULLUP_ZMAX
  551. //#define ENDSTOPPULLUP_XMIN
  552. //#define ENDSTOPPULLUP_YMIN
  553. //#define ENDSTOPPULLUP_ZMIN
  554. //#define ENDSTOPPULLUP_ZMIN_PROBE
  555. #endif
  556. // Enable pulldown for all endstops to prevent a floating state
  557. //#define ENDSTOPPULLDOWNS
  558. #if DISABLED(ENDSTOPPULLDOWNS)
  559. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  560. //#define ENDSTOPPULLDOWN_XMAX
  561. //#define ENDSTOPPULLDOWN_YMAX
  562. //#define ENDSTOPPULLDOWN_ZMAX
  563. //#define ENDSTOPPULLDOWN_XMIN
  564. //#define ENDSTOPPULLDOWN_YMIN
  565. //#define ENDSTOPPULLDOWN_ZMIN
  566. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  567. #endif
  568. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  569. #define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  570. #define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  571. #define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  572. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  573. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  574. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  575. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  576. /**
  577. * Stepper Drivers
  578. *
  579. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  580. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  581. *
  582. * A4988 is assumed for unspecified drivers.
  583. *
  584. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  585. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  586. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  587. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  588. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  589. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  590. */
  591. //#define X_DRIVER_TYPE A4988
  592. //#define Y_DRIVER_TYPE A4988
  593. //#define Z_DRIVER_TYPE A4988
  594. //#define X2_DRIVER_TYPE A4988
  595. //#define Y2_DRIVER_TYPE A4988
  596. //#define Z2_DRIVER_TYPE A4988
  597. //#define Z3_DRIVER_TYPE A4988
  598. //#define E0_DRIVER_TYPE A4988
  599. //#define E1_DRIVER_TYPE A4988
  600. //#define E2_DRIVER_TYPE A4988
  601. //#define E3_DRIVER_TYPE A4988
  602. //#define E4_DRIVER_TYPE A4988
  603. //#define E5_DRIVER_TYPE A4988
  604. // Enable this feature if all enabled endstop pins are interrupt-capable.
  605. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  606. #define ENDSTOP_INTERRUPTS_FEATURE
  607. /**
  608. * Endstop Noise Threshold
  609. *
  610. * Enable if your probe or endstops falsely trigger due to noise.
  611. *
  612. * - Higher values may affect repeatability or accuracy of some bed probes.
  613. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  614. * - This feature is not required for common micro-switches mounted on PCBs
  615. * based on the Makerbot design, which already have the 100nF capacitor.
  616. *
  617. * :[2,3,4,5,6,7]
  618. */
  619. //#define ENDSTOP_NOISE_THRESHOLD 2
  620. //=============================================================================
  621. //============================== Movement Settings ============================
  622. //=============================================================================
  623. // @section motion
  624. /**
  625. * Default Settings
  626. *
  627. * These settings can be reset by M502
  628. *
  629. * Note that if EEPROM is enabled, saved values will override these.
  630. */
  631. /**
  632. * With this option each E stepper can have its own factors for the
  633. * following movement settings. If fewer factors are given than the
  634. * total number of extruders, the last value applies to the rest.
  635. */
  636. //#define DISTINCT_E_FACTORS
  637. /**
  638. * Default Axis Steps Per Unit (steps/mm)
  639. * Override with M92
  640. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  641. */
  642. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  643. // ANET A6 Firmwae V2.0 defaults: (steps/mm)
  644. // Xsteps/mm: +100.0, Ysteps/mm: +100.0, Zsteps/mm: +0400.0, eSteps/mm: +0095.0
  645. #define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 95 }
  646. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 95 }
  647. /**
  648. * Default Max Feed Rate (mm/s)
  649. * Override with M203
  650. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  651. */
  652. //#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  653. // ANET A6 Firmware V2.0 defaults (Vmax):
  654. // Vmax x: 400, Vmax y: 400, Vmax z: 4, Vmax e: 25
  655. #define DEFAULT_MAX_FEEDRATE { 400, 400, 4, 25 }
  656. //#define DEFAULT_MAX_FEEDRATE { 400, 400, 20, 50 }
  657. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  658. #if ENABLED(LIMITED_MAX_FR_EDITING)
  659. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  660. #endif
  661. /**
  662. * Default Max Acceleration (change/s) change = mm/s
  663. * (Maximum start speed for accelerated moves)
  664. * Override with M201
  665. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  666. */
  667. //#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  668. // ANET A6 Firmware V2.0 defaults (Amax):
  669. // Amx x: 9000, Amax Y: 5000, Amax z: 50, Amax e: 10000
  670. #define DEFAULT_MAX_ACCELERATION { 9000, 5000, 50, 10000 }
  671. //#define DEFAULT_MAX_ACCELERATION { 10000, 10000, 200, 10000 }
  672. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  673. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  674. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  675. #endif
  676. /**
  677. * Default Acceleration (change/s) change = mm/s
  678. * Override with M204
  679. *
  680. * M204 P Acceleration
  681. * M204 R Retract Acceleration
  682. * M204 T Travel Acceleration
  683. */
  684. // ANET A6 Firmware V2.0 defaults:
  685. // Accel: 1000 A-retract: 1000
  686. #define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
  687. #define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
  688. #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
  689. /**
  690. * Default Jerk limits (mm/s)
  691. * Override with M205 X Y Z E
  692. *
  693. * "Jerk" specifies the minimum speed change that requires acceleration.
  694. * When changing speed and direction, if the difference is less than the
  695. * value set here, it may happen instantaneously.
  696. */
  697. //#define CLASSIC_JERK
  698. #if ENABLED(CLASSIC_JERK)
  699. // ANET A6 Firmware V2.0 defaults:
  700. // XY: 10, Z: +000.30, E: 5
  701. #define DEFAULT_XJERK 10.0
  702. #define DEFAULT_YJERK 10.0
  703. #define DEFAULT_ZJERK 0.3
  704. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  705. #if ENABLED(LIMITED_JERK_EDITING)
  706. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  707. #endif
  708. #endif
  709. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  710. /**
  711. * Junction Deviation Factor
  712. *
  713. * See:
  714. * https://reprap.org/forum/read.php?1,739819
  715. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  716. */
  717. #if DISABLED(CLASSIC_JERK)
  718. #define JUNCTION_DEVIATION_MM 0.04 // (mm) Distance from real junction edge
  719. #endif
  720. /**
  721. * S-Curve Acceleration
  722. *
  723. * This option eliminates vibration during printing by fitting a Bézier
  724. * curve to move acceleration, producing much smoother direction changes.
  725. *
  726. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  727. */
  728. //#define S_CURVE_ACCELERATION
  729. //===========================================================================
  730. //============================= Z Probe Options =============================
  731. //===========================================================================
  732. // @section probes
  733. //
  734. // See http://marlinfw.org/docs/configuration/probes.html
  735. //
  736. /**
  737. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  738. *
  739. * Enable this option for a probe connected to the Z Min endstop pin.
  740. */
  741. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  742. /**
  743. * Z_MIN_PROBE_PIN
  744. *
  745. * Define this pin if the probe is not connected to Z_MIN_PIN.
  746. * If not defined the default pin for the selected MOTHERBOARD
  747. * will be used. Most of the time the default is what you want.
  748. *
  749. * - The simplest option is to use a free endstop connector.
  750. * - Use 5V for powered (usually inductive) sensors.
  751. *
  752. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  753. * - For simple switches connect...
  754. * - normally-closed switches to GND and D32.
  755. * - normally-open switches to 5V and D32.
  756. *
  757. */
  758. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  759. /**
  760. * Probe Type
  761. *
  762. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  763. * Activate one of these to use Auto Bed Leveling below.
  764. */
  765. /**
  766. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  767. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  768. * or (with LCD_BED_LEVELING) the LCD controller.
  769. */
  770. //#define PROBE_MANUALLY
  771. //#define MANUAL_PROBE_START_Z 0.2
  772. /**
  773. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  774. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  775. */
  776. //#define FIX_MOUNTED_PROBE
  777. /**
  778. * Z Servo Probe, such as an endstop switch on a rotating arm.
  779. */
  780. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  781. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  782. /**
  783. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  784. */
  785. //#define BLTOUCH
  786. /**
  787. * Touch-MI Probe by hotends.fr
  788. *
  789. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  790. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  791. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  792. *
  793. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  794. * and a minimum Z_HOMING_HEIGHT of 10.
  795. */
  796. //#define TOUCH_MI_PROBE
  797. #if ENABLED(TOUCH_MI_PROBE)
  798. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  799. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  800. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  801. #endif
  802. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  803. //#define SOLENOID_PROBE
  804. // A sled-mounted probe like those designed by Charles Bell.
  805. //#define Z_PROBE_SLED
  806. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  807. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  808. //#define RACK_AND_PINION_PROBE
  809. #if ENABLED(RACK_AND_PINION_PROBE)
  810. #define Z_PROBE_DEPLOY_X X_MIN_POS
  811. #define Z_PROBE_RETRACT_X X_MAX_POS
  812. #endif
  813. //
  814. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  815. //
  816. /**
  817. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  818. *
  819. * In the following example the X and Y offsets are both positive:
  820. *
  821. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  822. *
  823. * +-- BACK ---+
  824. * | |
  825. * L | (+) P | R <-- probe (20,20)
  826. * E | | I
  827. * F | (-) N (+) | G <-- nozzle (10,10)
  828. * T | | H
  829. * | (-) | T
  830. * | |
  831. * O-- FRONT --+
  832. * (0,0)
  833. *
  834. * Specify a Probe position as { X, Y, Z }
  835. */
  836. //#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  837. // ANET A8: FRONT-MOUNTED SENSOR WITH 3D PRINTED MOUNT
  838. //#define NOZZLE_TO_PROBE_OFFSET { -28, -45, 0 }
  839. // THESE ARE FOR THE OFFICIAL ANET REAR-MOUNTED SENSOR
  840. //#define NOZZLE_TO_PROBE_OFFSET { -1, 3, 0 }
  841. // ANET A6 with BLTouch/3D-Touch mounted right to the nozzle
  842. #define NOZZLE_TO_PROBE_OFFSET { 39, 0, 0 }
  843. //ANET A6 with BLTouch/3D-Touch betwen Fan and Belt
  844. // (mount: https://github.com/ralf-e/ANET_A6_modifications/tree/master/A6_X-Axis)
  845. //#define NOZZLE_TO_PROBE_OFFSET { -30, 15, 0.75 }
  846. // Certain types of probes need to stay away from edges
  847. #define MIN_PROBE_EDGE 10
  848. // X and Y axis travel speed (mm/m) between probes
  849. #define XY_PROBE_SPEED 8000
  850. //#define XY_PROBE_SPEED 6000
  851. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  852. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  853. // Feedrate (mm/m) for the "accurate" probe of each point
  854. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 3)
  855. /**
  856. * Multiple Probing
  857. *
  858. * You may get improved results by probing 2 or more times.
  859. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  860. *
  861. * A total of 2 does fast/slow probes with a weighted average.
  862. * A total of 3 or more adds more slow probes, taking the average.
  863. */
  864. #define MULTIPLE_PROBING 2
  865. //#define EXTRA_PROBING 1
  866. /**
  867. * Z probes require clearance when deploying, stowing, and moving between
  868. * probe points to avoid hitting the bed and other hardware.
  869. * Servo-mounted probes require extra space for the arm to rotate.
  870. * Inductive probes need space to keep from triggering early.
  871. *
  872. * Use these settings to specify the distance (mm) to raise the probe (or
  873. * lower the bed). The values set here apply over and above any (negative)
  874. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  875. * Only integer values >= 1 are valid here.
  876. *
  877. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  878. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  879. */
  880. #if 1 // 0 for less clearance
  881. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  882. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  883. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  884. #else
  885. #define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
  886. #define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points
  887. //#define Z_AFTER_PROBING 3 // Z position after probing is done
  888. #endif
  889. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  890. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  891. // For M851 give a range for adjusting the Z probe offset
  892. #define Z_PROBE_OFFSET_RANGE_MIN -20
  893. #define Z_PROBE_OFFSET_RANGE_MAX 20
  894. // Enable the M48 repeatability test to test probe accuracy
  895. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  896. // Before deploy/stow pause for user confirmation
  897. //#define PAUSE_BEFORE_DEPLOY_STOW
  898. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  899. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  900. #endif
  901. /**
  902. * Enable one or more of the following if probing seems unreliable.
  903. * Heaters and/or fans can be disabled during probing to minimize electrical
  904. * noise. A delay can also be added to allow noise and vibration to settle.
  905. * These options are most useful for the BLTouch probe, but may also improve
  906. * readings with inductive probes and piezo sensors.
  907. */
  908. #define PROBING_HEATERS_OFF // Turn heaters off when probing
  909. #if ENABLED(PROBING_HEATERS_OFF)
  910. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  911. #endif
  912. #define PROBING_FANS_OFF // Turn fans off when probing
  913. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  914. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  915. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  916. // :{ 0:'Low', 1:'High' }
  917. #define X_ENABLE_ON 0
  918. #define Y_ENABLE_ON 0
  919. #define Z_ENABLE_ON 0
  920. #define E_ENABLE_ON 0 // For all extruders
  921. // Disables axis stepper immediately when it's not being used.
  922. // WARNING: When motors turn off there is a chance of losing position accuracy!
  923. #define DISABLE_X false
  924. #define DISABLE_Y false
  925. #define DISABLE_Z false
  926. // Warn on display about possibly reduced accuracy
  927. //#define DISABLE_REDUCED_ACCURACY_WARNING
  928. // @section extruder
  929. #define DISABLE_E false // For all extruders
  930. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  931. // @section machine
  932. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  933. #define INVERT_X_DIR false
  934. //#define INVERT_Y_DIR true
  935. //#define INVERT_Z_DIR false
  936. //ANET A6:
  937. #define INVERT_Y_DIR false
  938. #define INVERT_Z_DIR true
  939. // @section extruder
  940. // For direct drive extruder v9 set to true, for geared extruder set to false.
  941. #define INVERT_E0_DIR false
  942. #define INVERT_E1_DIR false
  943. #define INVERT_E2_DIR false
  944. #define INVERT_E3_DIR false
  945. #define INVERT_E4_DIR false
  946. #define INVERT_E5_DIR false
  947. // @section homing
  948. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  949. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  950. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  951. // Be sure you have this distance over your Z_MAX_POS in case.
  952. // Direction of endstops when homing; 1=MAX, -1=MIN
  953. // :[-1,1]
  954. #define X_HOME_DIR -1
  955. #define Y_HOME_DIR -1
  956. #define Z_HOME_DIR -1
  957. // @section machine
  958. // The size of the print bed
  959. //#define X_BED_SIZE 200
  960. //#define Y_BED_SIZE 200
  961. // Travel limits (mm) after homing, corresponding to endstop positions.
  962. //#define X_MIN_POS 0
  963. //#define Y_MIN_POS 0
  964. //#define X_MAX_POS X_BED_SIZE
  965. //#define Y_MAX_POS Y_BED_SIZE
  966. //#define Z_MIN_POS 0
  967. //#define Z_MAX_POS 200
  968. // ANET A6 Firmware V2.0 defaults:
  969. //#define X_BED_SIZE 220
  970. //#define Y_BED_SIZE 220
  971. //#define X_MIN_POS 0
  972. //#define Y_MIN_POS 0
  973. //#define Z_MIN_POS 0
  974. //#define Z_MAX_POS 250
  975. // ANET A6, X0/Y0 0 front left bed edge :
  976. #define X_BED_SIZE 222
  977. #define Y_BED_SIZE 222
  978. #define X_MIN_POS -3
  979. #define Y_MIN_POS -5
  980. #define Z_MIN_POS 0
  981. #define Z_MAX_POS 230
  982. // ANET A6 with new X-Axis / modded Y-Axis:
  983. //#define X_BED_SIZE 235
  984. //#define Y_BED_SIZE 230
  985. //#define X_MIN_POS 0
  986. //#define Y_MIN_POS 0
  987. //#define Z_MIN_POS 0
  988. //#define Z_MAX_POS 230
  989. // ANET A6 with new X-Axis / modded Y-Axis, X0/Y0 0 front left bed edge :
  990. //#define X_BED_SIZE 227
  991. //#define Y_BED_SIZE 224
  992. //#define X_MIN_POS -8
  993. //#define Y_MIN_POS -6
  994. //#define Z_MIN_POS 0
  995. //#define Z_MAX_POS 230
  996. #define X_MAX_POS X_BED_SIZE
  997. #define Y_MAX_POS Y_BED_SIZE
  998. /**
  999. * Software Endstops
  1000. *
  1001. * - Prevent moves outside the set machine bounds.
  1002. * - Individual axes can be disabled, if desired.
  1003. * - X and Y only apply to Cartesian robots.
  1004. * - Use 'M211' to set software endstops on/off or report current state
  1005. */
  1006. // Min software endstops constrain movement within minimum coordinate bounds
  1007. #define MIN_SOFTWARE_ENDSTOPS
  1008. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  1009. #define MIN_SOFTWARE_ENDSTOP_X
  1010. #define MIN_SOFTWARE_ENDSTOP_Y
  1011. #define MIN_SOFTWARE_ENDSTOP_Z
  1012. #endif
  1013. // Max software endstops constrain movement within maximum coordinate bounds
  1014. #define MAX_SOFTWARE_ENDSTOPS
  1015. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  1016. #define MAX_SOFTWARE_ENDSTOP_X
  1017. #define MAX_SOFTWARE_ENDSTOP_Y
  1018. #define MAX_SOFTWARE_ENDSTOP_Z
  1019. #endif
  1020. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  1021. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  1022. #endif
  1023. /**
  1024. * Filament Runout Sensors
  1025. * Mechanical or opto endstops are used to check for the presence of filament.
  1026. *
  1027. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  1028. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  1029. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  1030. */
  1031. //#define FILAMENT_RUNOUT_SENSOR
  1032. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  1033. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  1034. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  1035. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  1036. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  1037. // Set one or more commands to execute on filament runout.
  1038. // (After 'M412 H' Marlin will ask the host to handle the process.)
  1039. #define FILAMENT_RUNOUT_SCRIPT "M600"
  1040. // After a runout is detected, continue printing this length of filament
  1041. // before executing the runout script. Useful for a sensor at the end of
  1042. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  1043. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  1044. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  1045. // Enable this option to use an encoder disc that toggles the runout pin
  1046. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  1047. // large enough to avoid false positives.)
  1048. //#define FILAMENT_MOTION_SENSOR
  1049. #endif
  1050. #endif
  1051. //===========================================================================
  1052. //=============================== Bed Leveling ==============================
  1053. //===========================================================================
  1054. // @section calibrate
  1055. /**
  1056. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  1057. * and behavior of G29 will change depending on your selection.
  1058. *
  1059. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  1060. *
  1061. * - AUTO_BED_LEVELING_3POINT
  1062. * Probe 3 arbitrary points on the bed (that aren't collinear)
  1063. * You specify the XY coordinates of all 3 points.
  1064. * The result is a single tilted plane. Best for a flat bed.
  1065. *
  1066. * - AUTO_BED_LEVELING_LINEAR
  1067. * Probe several points in a grid.
  1068. * You specify the rectangle and the density of sample points.
  1069. * The result is a single tilted plane. Best for a flat bed.
  1070. *
  1071. * - AUTO_BED_LEVELING_BILINEAR
  1072. * Probe several points in a grid.
  1073. * You specify the rectangle and the density of sample points.
  1074. * The result is a mesh, best for large or uneven beds.
  1075. *
  1076. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1077. * A comprehensive bed leveling system combining the features and benefits
  1078. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1079. * Validation and Mesh Editing systems.
  1080. *
  1081. * - MESH_BED_LEVELING
  1082. * Probe a grid manually
  1083. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1084. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1085. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1086. * With an LCD controller the process is guided step-by-step.
  1087. */
  1088. //#define AUTO_BED_LEVELING_3POINT
  1089. //#define AUTO_BED_LEVELING_LINEAR
  1090. //#define AUTO_BED_LEVELING_BILINEAR
  1091. //#define AUTO_BED_LEVELING_UBL
  1092. //#define MESH_BED_LEVELING
  1093. /**
  1094. * Normally G28 leaves leveling disabled on completion. Enable
  1095. * this option to have G28 restore the prior leveling state.
  1096. */
  1097. //#define RESTORE_LEVELING_AFTER_G28
  1098. /**
  1099. * Enable detailed logging of G28, G29, M48, etc.
  1100. * Turn on with the command 'M111 S32'.
  1101. * NOTE: Requires a lot of PROGMEM!
  1102. */
  1103. //#define DEBUG_LEVELING_FEATURE
  1104. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1105. // Gradually reduce leveling correction until a set height is reached,
  1106. // at which point movement will be level to the machine's XY plane.
  1107. // The height can be set with M420 Z<height>
  1108. #define ENABLE_LEVELING_FADE_HEIGHT
  1109. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1110. // split up moves into short segments like a Delta. This follows the
  1111. // contours of the bed more closely than edge-to-edge straight moves.
  1112. #define SEGMENT_LEVELED_MOVES
  1113. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1114. /**
  1115. * Enable the G26 Mesh Validation Pattern tool.
  1116. */
  1117. //#define G26_MESH_VALIDATION
  1118. #if ENABLED(G26_MESH_VALIDATION)
  1119. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1120. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1121. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1122. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1123. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1124. #endif
  1125. #endif
  1126. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1127. // Set the number of grid points per dimension.
  1128. #define GRID_MAX_POINTS_X 4
  1129. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1130. // Probe along the Y axis, advancing X after each column
  1131. //#define PROBE_Y_FIRST
  1132. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1133. // Beyond the probed grid, continue the implied tilt?
  1134. // Default is to maintain the height of the nearest edge.
  1135. //#define EXTRAPOLATE_BEYOND_GRID
  1136. //
  1137. // Experimental Subdivision of the grid by Catmull-Rom method.
  1138. // Synthesizes intermediate points to produce a more detailed mesh.
  1139. //
  1140. //#define ABL_BILINEAR_SUBDIVISION
  1141. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1142. // Number of subdivisions between probe points
  1143. #define BILINEAR_SUBDIVISIONS 3
  1144. #endif
  1145. #endif
  1146. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1147. //===========================================================================
  1148. //========================= Unified Bed Leveling ============================
  1149. //===========================================================================
  1150. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1151. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1152. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1153. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1154. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1155. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1156. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1157. // as the Z-Height correction value.
  1158. #elif ENABLED(MESH_BED_LEVELING)
  1159. //===========================================================================
  1160. //=================================== Mesh ==================================
  1161. //===========================================================================
  1162. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1163. #define GRID_MAX_POINTS_X 5 // Don't use more than 7 points per axis, implementation limited.
  1164. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1165. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1166. #endif // BED_LEVELING
  1167. /**
  1168. * Add a bed leveling sub-menu for ABL or MBL.
  1169. * Include a guided procedure if manual probing is enabled.
  1170. */
  1171. //#define LCD_BED_LEVELING
  1172. #if ENABLED(LCD_BED_LEVELING)
  1173. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1174. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1175. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1176. #endif
  1177. // Add a menu item to move between bed corners for manual bed adjustment
  1178. //#define LEVEL_BED_CORNERS
  1179. #if ENABLED(LEVEL_BED_CORNERS)
  1180. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1181. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1182. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1183. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1184. #endif
  1185. /**
  1186. * Commands to execute at the end of G29 probing.
  1187. * Useful to retract or move the Z probe out of the way.
  1188. */
  1189. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1190. // @section homing
  1191. // The center of the bed is at (X=0, Y=0)
  1192. //#define BED_CENTER_AT_0_0
  1193. // Manually set the home position. Leave these undefined for automatic settings.
  1194. // For DELTA this is the top-center of the Cartesian print volume.
  1195. //#define MANUAL_X_HOME_POS 0
  1196. //#define MANUAL_Y_HOME_POS 0
  1197. //#define MANUAL_Z_HOME_POS 0
  1198. // ANET A6 with new X-Axis / modded Y-Axis:
  1199. //#define MANUAL_X_HOME_POS X_MIN_POS - 8
  1200. //#define MANUAL_Y_HOME_POS Y_MIN_POS - 6
  1201. //#define MANUAL_Z_HOME_POS Z_MIN_POS
  1202. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1203. //
  1204. // With this feature enabled:
  1205. //
  1206. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1207. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1208. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1209. // - Prevent Z homing when the Z probe is outside bed area.
  1210. //
  1211. #define Z_SAFE_HOMING
  1212. #if ENABLED(Z_SAFE_HOMING)
  1213. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1214. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1215. //Anet A6 with new X-Axis
  1216. //#define Z_SAFE_HOMING_X_POINT 113 // X point for Z homing when homing all axes (G28).
  1217. //#define Z_SAFE_HOMING_Y_POINT 112 // Y point for Z homing when homing all axes (G28).
  1218. //Anet A6 with new X-Axis and defined X_HOME_POS -7, Y_HOME_POS -6
  1219. //#define Z_SAFE_HOMING_X_POINT 107 // X point for Z homing when homing all axes (G28).
  1220. //#define Z_SAFE_HOMING_Y_POINT 107 // Y point for Z homing when homing all axes (G28).
  1221. #endif
  1222. // Homing speeds (mm/m)
  1223. #define HOMING_FEEDRATE_XY (50*60)
  1224. #define HOMING_FEEDRATE_Z (4*60)
  1225. // Validate that endstops are triggered on homing moves
  1226. #define VALIDATE_HOMING_ENDSTOPS
  1227. // @section calibrate
  1228. /**
  1229. * Bed Skew Compensation
  1230. *
  1231. * This feature corrects for misalignment in the XYZ axes.
  1232. *
  1233. * Take the following steps to get the bed skew in the XY plane:
  1234. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1235. * 2. For XY_DIAG_AC measure the diagonal A to C
  1236. * 3. For XY_DIAG_BD measure the diagonal B to D
  1237. * 4. For XY_SIDE_AD measure the edge A to D
  1238. *
  1239. * Marlin automatically computes skew factors from these measurements.
  1240. * Skew factors may also be computed and set manually:
  1241. *
  1242. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1243. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1244. *
  1245. * If desired, follow the same procedure for XZ and YZ.
  1246. * Use these diagrams for reference:
  1247. *
  1248. * Y Z Z
  1249. * ^ B-------C ^ B-------C ^ B-------C
  1250. * | / / | / / | / /
  1251. * | / / | / / | / /
  1252. * | A-------D | A-------D | A-------D
  1253. * +-------------->X +-------------->X +-------------->Y
  1254. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1255. */
  1256. //#define SKEW_CORRECTION
  1257. #if ENABLED(SKEW_CORRECTION)
  1258. // Input all length measurements here:
  1259. #define XY_DIAG_AC 282.8427124746
  1260. #define XY_DIAG_BD 282.8427124746
  1261. #define XY_SIDE_AD 200
  1262. // Or, set the default skew factors directly here
  1263. // to override the above measurements:
  1264. #define XY_SKEW_FACTOR 0.0
  1265. //#define SKEW_CORRECTION_FOR_Z
  1266. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1267. #define XZ_DIAG_AC 282.8427124746
  1268. #define XZ_DIAG_BD 282.8427124746
  1269. #define YZ_DIAG_AC 282.8427124746
  1270. #define YZ_DIAG_BD 282.8427124746
  1271. #define YZ_SIDE_AD 200
  1272. #define XZ_SKEW_FACTOR 0.0
  1273. #define YZ_SKEW_FACTOR 0.0
  1274. #endif
  1275. // Enable this option for M852 to set skew at runtime
  1276. //#define SKEW_CORRECTION_GCODE
  1277. #endif
  1278. //=============================================================================
  1279. //============================= Additional Features ===========================
  1280. //=============================================================================
  1281. // @section extras
  1282. /**
  1283. * EEPROM
  1284. *
  1285. * Persistent storage to preserve configurable settings across reboots.
  1286. *
  1287. * M500 - Store settings to EEPROM.
  1288. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1289. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1290. */
  1291. #define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1292. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1293. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1294. #if ENABLED(EEPROM_SETTINGS)
  1295. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1296. #endif
  1297. //
  1298. // Host Keepalive
  1299. //
  1300. // When enabled Marlin will send a busy status message to the host
  1301. // every couple of seconds when it can't accept commands.
  1302. //
  1303. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1304. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1305. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1306. //
  1307. // M100 Free Memory Watcher
  1308. //
  1309. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1310. //
  1311. // G20/G21 Inch mode support
  1312. //
  1313. //#define INCH_MODE_SUPPORT
  1314. //
  1315. // M149 Set temperature units support
  1316. //
  1317. //#define TEMPERATURE_UNITS_SUPPORT
  1318. // @section temperature
  1319. // Preheat Constants
  1320. #define PREHEAT_1_LABEL "PLA"
  1321. #define PREHEAT_1_TEMP_HOTEND 200
  1322. #define PREHEAT_1_TEMP_BED 50
  1323. #define PREHEAT_1_FAN_SPEED 0 // ANET A6 Default is 255
  1324. #define PREHEAT_2_LABEL "ABS"
  1325. #define PREHEAT_2_TEMP_HOTEND 230
  1326. #define PREHEAT_2_TEMP_BED 70
  1327. #define PREHEAT_2_FAN_SPEED 0 // ANET A6 Default is 255
  1328. /**
  1329. * Nozzle Park
  1330. *
  1331. * Park the nozzle at the given XYZ position on idle or G27.
  1332. *
  1333. * The "P" parameter controls the action applied to the Z axis:
  1334. *
  1335. * P0 (Default) If Z is below park Z raise the nozzle.
  1336. * P1 Raise the nozzle always to Z-park height.
  1337. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1338. */
  1339. //#define NOZZLE_PARK_FEATURE
  1340. #if ENABLED(NOZZLE_PARK_FEATURE)
  1341. // Specify a park position as { X, Y, Z_raise }
  1342. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1343. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1344. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1345. #endif
  1346. /**
  1347. * Clean Nozzle Feature -- EXPERIMENTAL
  1348. *
  1349. * Adds the G12 command to perform a nozzle cleaning process.
  1350. *
  1351. * Parameters:
  1352. * P Pattern
  1353. * S Strokes / Repetitions
  1354. * T Triangles (P1 only)
  1355. *
  1356. * Patterns:
  1357. * P0 Straight line (default). This process requires a sponge type material
  1358. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1359. * between the start / end points.
  1360. *
  1361. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1362. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1363. * Zig-zags are done in whichever is the narrower dimension.
  1364. * For example, "G12 P1 S1 T3" will execute:
  1365. *
  1366. * --
  1367. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1368. * | | / \ / \ / \ |
  1369. * A | | / \ / \ / \ |
  1370. * | | / \ / \ / \ |
  1371. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1372. * -- +--------------------------------+
  1373. * |________|_________|_________|
  1374. * T1 T2 T3
  1375. *
  1376. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1377. * "R" specifies the radius. "S" specifies the stroke count.
  1378. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1379. *
  1380. * Caveats: The ending Z should be the same as starting Z.
  1381. * Attention: EXPERIMENTAL. G-code arguments may change.
  1382. *
  1383. */
  1384. //#define NOZZLE_CLEAN_FEATURE
  1385. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1386. // Default number of pattern repetitions
  1387. #define NOZZLE_CLEAN_STROKES 12
  1388. // Default number of triangles
  1389. #define NOZZLE_CLEAN_TRIANGLES 3
  1390. // Specify positions as { X, Y, Z }
  1391. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1) }
  1392. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1393. // Circular pattern radius
  1394. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1395. // Circular pattern circle fragments number
  1396. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1397. // Middle point of circle
  1398. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1399. // Move the nozzle to the initial position after cleaning
  1400. #define NOZZLE_CLEAN_GOBACK
  1401. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1402. //#define NOZZLE_CLEAN_NO_Z
  1403. #endif
  1404. /**
  1405. * Print Job Timer
  1406. *
  1407. * Automatically start and stop the print job timer on M104/M109/M190.
  1408. *
  1409. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1410. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1411. * M190 (bed, wait) - high temp = start timer, low temp = none
  1412. *
  1413. * The timer can also be controlled with the following commands:
  1414. *
  1415. * M75 - Start the print job timer
  1416. * M76 - Pause the print job timer
  1417. * M77 - Stop the print job timer
  1418. */
  1419. #define PRINTJOB_TIMER_AUTOSTART
  1420. /**
  1421. * Print Counter
  1422. *
  1423. * Track statistical data such as:
  1424. *
  1425. * - Total print jobs
  1426. * - Total successful print jobs
  1427. * - Total failed print jobs
  1428. * - Total time printing
  1429. *
  1430. * View the current statistics with M78.
  1431. */
  1432. //#define PRINTCOUNTER
  1433. //=============================================================================
  1434. //============================= LCD and SD support ============================
  1435. //=============================================================================
  1436. // @section lcd
  1437. /**
  1438. * LCD LANGUAGE
  1439. *
  1440. * Select the language to display on the LCD. These languages are available:
  1441. *
  1442. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
  1443. * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1444. *
  1445. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1446. */
  1447. #define LCD_LANGUAGE en
  1448. /**
  1449. * LCD Character Set
  1450. *
  1451. * Note: This option is NOT applicable to Graphical Displays.
  1452. *
  1453. * All character-based LCDs provide ASCII plus one of these
  1454. * language extensions:
  1455. *
  1456. * - JAPANESE ... the most common
  1457. * - WESTERN ... with more accented characters
  1458. * - CYRILLIC ... for the Russian language
  1459. *
  1460. * To determine the language extension installed on your controller:
  1461. *
  1462. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1463. * - Click the controller to view the LCD menu
  1464. * - The LCD will display Japanese, Western, or Cyrillic text
  1465. *
  1466. * See http://marlinfw.org/docs/development/lcd_language.html
  1467. *
  1468. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1469. */
  1470. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1471. /**
  1472. * Info Screen Style (0:Classic, 1:Prusa)
  1473. *
  1474. * :[0:'Classic', 1:'Prusa']
  1475. */
  1476. #define LCD_INFO_SCREEN_STYLE 0
  1477. /**
  1478. * SD CARD
  1479. *
  1480. * SD Card support is disabled by default. If your controller has an SD slot,
  1481. * you must uncomment the following option or it won't work.
  1482. *
  1483. */
  1484. #define SDSUPPORT
  1485. /**
  1486. * SD CARD: SPI SPEED
  1487. *
  1488. * Enable one of the following items for a slower SPI transfer speed.
  1489. * This may be required to resolve "volume init" errors.
  1490. */
  1491. //#define SPI_SPEED SPI_HALF_SPEED
  1492. //#define SPI_SPEED SPI_QUARTER_SPEED
  1493. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1494. /**
  1495. * SD CARD: ENABLE CRC
  1496. *
  1497. * Use CRC checks and retries on the SD communication.
  1498. */
  1499. //#define SD_CHECK_AND_RETRY
  1500. /**
  1501. * LCD Menu Items
  1502. *
  1503. * Disable all menus and only display the Status Screen, or
  1504. * just remove some extraneous menu items to recover space.
  1505. */
  1506. //#define NO_LCD_MENUS
  1507. //#define SLIM_LCD_MENUS
  1508. //
  1509. // ENCODER SETTINGS
  1510. //
  1511. // This option overrides the default number of encoder pulses needed to
  1512. // produce one step. Should be increased for high-resolution encoders.
  1513. //
  1514. //#define ENCODER_PULSES_PER_STEP 4
  1515. //
  1516. // Use this option to override the number of step signals required to
  1517. // move between next/prev menu items.
  1518. //
  1519. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1520. /**
  1521. * Encoder Direction Options
  1522. *
  1523. * Test your encoder's behavior first with both options disabled.
  1524. *
  1525. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1526. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1527. * Reversed Value Editing only? Enable BOTH options.
  1528. */
  1529. //
  1530. // This option reverses the encoder direction everywhere.
  1531. //
  1532. // Set this option if CLOCKWISE causes values to DECREASE
  1533. //
  1534. //#define REVERSE_ENCODER_DIRECTION
  1535. //
  1536. // This option reverses the encoder direction for navigating LCD menus.
  1537. //
  1538. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1539. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1540. //
  1541. //#define REVERSE_MENU_DIRECTION
  1542. //
  1543. // This option reverses the encoder direction for Select Screen.
  1544. //
  1545. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1546. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1547. //
  1548. //#define REVERSE_SELECT_DIRECTION
  1549. //
  1550. // Individual Axis Homing
  1551. //
  1552. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1553. //
  1554. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1555. //
  1556. // SPEAKER/BUZZER
  1557. //
  1558. // If you have a speaker that can produce tones, enable it here.
  1559. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1560. //
  1561. //#define SPEAKER
  1562. //
  1563. // The duration and frequency for the UI feedback sound.
  1564. // Set these to 0 to disable audio feedback in the LCD menus.
  1565. //
  1566. // Note: Test audio output with the G-Code:
  1567. // M300 S<frequency Hz> P<duration ms>
  1568. //
  1569. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1570. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1571. //=============================================================================
  1572. //======================== LCD / Controller Selection =========================
  1573. //======================== (Character-based LCDs) =========================
  1574. //=============================================================================
  1575. //
  1576. // RepRapDiscount Smart Controller.
  1577. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1578. //
  1579. // Note: Usually sold with a white PCB.
  1580. //
  1581. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1582. //
  1583. // Original RADDS LCD Display+Encoder+SDCardReader
  1584. // http://doku.radds.org/dokumentation/lcd-display/
  1585. //
  1586. //#define RADDS_DISPLAY
  1587. //
  1588. // ULTIMAKER Controller.
  1589. //
  1590. //#define ULTIMAKERCONTROLLER
  1591. //
  1592. // ULTIPANEL as seen on Thingiverse.
  1593. //
  1594. //#define ULTIPANEL
  1595. //
  1596. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1597. // http://reprap.org/wiki/PanelOne
  1598. //
  1599. //#define PANEL_ONE
  1600. //
  1601. // GADGETS3D G3D LCD/SD Controller
  1602. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1603. //
  1604. // Note: Usually sold with a blue PCB.
  1605. //
  1606. //#define G3D_PANEL
  1607. //
  1608. // RigidBot Panel V1.0
  1609. // http://www.inventapart.com/
  1610. //
  1611. //#define RIGIDBOT_PANEL
  1612. //
  1613. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1614. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1615. //
  1616. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1617. //
  1618. // ANET and Tronxy 20x4 Controller
  1619. //
  1620. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1621. // This LCD is known to be susceptible to electrical interference
  1622. // which scrambles the display. Pressing any button clears it up.
  1623. // This is a LCD2004 display with 5 analog buttons.
  1624. //
  1625. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1626. //
  1627. //#define ULTRA_LCD
  1628. //=============================================================================
  1629. //======================== LCD / Controller Selection =========================
  1630. //===================== (I2C and Shift-Register LCDs) =====================
  1631. //=============================================================================
  1632. //
  1633. // CONTROLLER TYPE: I2C
  1634. //
  1635. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1636. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1637. //
  1638. //
  1639. // Elefu RA Board Control Panel
  1640. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1641. //
  1642. //#define RA_CONTROL_PANEL
  1643. //
  1644. // Sainsmart (YwRobot) LCD Displays
  1645. //
  1646. // These require F.Malpartida's LiquidCrystal_I2C library
  1647. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1648. //
  1649. //#define LCD_SAINSMART_I2C_1602
  1650. //#define LCD_SAINSMART_I2C_2004
  1651. //
  1652. // Generic LCM1602 LCD adapter
  1653. //
  1654. //#define LCM1602
  1655. //
  1656. // PANELOLU2 LCD with status LEDs,
  1657. // separate encoder and click inputs.
  1658. //
  1659. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1660. // For more info: https://github.com/lincomatic/LiquidTWI2
  1661. //
  1662. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1663. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1664. //
  1665. //#define LCD_I2C_PANELOLU2
  1666. //
  1667. // Panucatt VIKI LCD with status LEDs,
  1668. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1669. //
  1670. //#define LCD_I2C_VIKI
  1671. //
  1672. // CONTROLLER TYPE: Shift register panels
  1673. //
  1674. //
  1675. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1676. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1677. //
  1678. //#define SAV_3DLCD
  1679. //
  1680. // 3-wire SR LCD with strobe using 74HC4094
  1681. // https://github.com/mikeshub/SailfishLCD
  1682. // Uses the code directly from Sailfish
  1683. //
  1684. //#define FF_INTERFACEBOARD
  1685. //=============================================================================
  1686. //======================= LCD / Controller Selection =======================
  1687. //========================= (Graphical LCDs) ========================
  1688. //=============================================================================
  1689. //
  1690. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1691. //
  1692. // IMPORTANT: The U8glib library is required for Graphical Display!
  1693. // https://github.com/olikraus/U8glib_Arduino
  1694. //
  1695. //
  1696. // RepRapDiscount FULL GRAPHIC Smart Controller
  1697. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1698. //
  1699. // Note: Details on connecting to the Anet V1.0 controller are in the file pins_ANET_10.h
  1700. //
  1701. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1702. //
  1703. // ReprapWorld Graphical LCD
  1704. // https://reprapworld.com/?products_details&products_id/1218
  1705. //
  1706. //#define REPRAPWORLD_GRAPHICAL_LCD
  1707. //
  1708. // Activate one of these if you have a Panucatt Devices
  1709. // Viki 2.0 or mini Viki with Graphic LCD
  1710. // http://panucatt.com
  1711. //
  1712. //#define VIKI2
  1713. //#define miniVIKI
  1714. //
  1715. // MakerLab Mini Panel with graphic
  1716. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1717. //
  1718. //#define MINIPANEL
  1719. //
  1720. // MaKr3d Makr-Panel with graphic controller and SD support.
  1721. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1722. //
  1723. //#define MAKRPANEL
  1724. //
  1725. // Adafruit ST7565 Full Graphic Controller.
  1726. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1727. //
  1728. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1729. //
  1730. // BQ LCD Smart Controller shipped by
  1731. // default with the BQ Hephestos 2 and Witbox 2.
  1732. //
  1733. //#define BQ_LCD_SMART_CONTROLLER
  1734. //
  1735. // Cartesio UI
  1736. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1737. //
  1738. //#define CARTESIO_UI
  1739. //
  1740. // LCD for Melzi Card with Graphical LCD
  1741. //
  1742. //#define LCD_FOR_MELZI
  1743. //
  1744. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1745. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1746. //
  1747. //#define ULTI_CONTROLLER
  1748. //
  1749. // MKS MINI12864 with graphic controller and SD support
  1750. // https://reprap.org/wiki/MKS_MINI_12864
  1751. //
  1752. //#define MKS_MINI_12864
  1753. //
  1754. // FYSETC variant of the MINI12864 graphic controller with SD support
  1755. // https://wiki.fysetc.com/Mini12864_Panel/
  1756. //
  1757. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1758. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1759. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1760. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1761. //
  1762. // Factory display for Creality CR-10
  1763. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1764. //
  1765. // This is RAMPS-compatible using a single 10-pin connector.
  1766. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1767. //
  1768. //#define CR10_STOCKDISPLAY
  1769. //
  1770. // ANET and Tronxy Graphical Controller
  1771. //
  1772. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1773. // A clone of the RepRapDiscount full graphics display but with
  1774. // different pins/wiring (see pins_ANET_10.h).
  1775. //
  1776. #define ANET_FULL_GRAPHICS_LCD
  1777. //
  1778. // AZSMZ 12864 LCD with SD
  1779. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1780. //
  1781. //#define AZSMZ_12864
  1782. //
  1783. // Silvergate GLCD controller
  1784. // http://github.com/android444/Silvergate
  1785. //
  1786. //#define SILVER_GATE_GLCD_CONTROLLER
  1787. //=============================================================================
  1788. //============================== OLED Displays ==============================
  1789. //=============================================================================
  1790. //
  1791. // SSD1306 OLED full graphics generic display
  1792. //
  1793. //#define U8GLIB_SSD1306
  1794. //
  1795. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1796. //
  1797. //#define SAV_3DGLCD
  1798. #if ENABLED(SAV_3DGLCD)
  1799. #define U8GLIB_SSD1306
  1800. //#define U8GLIB_SH1106
  1801. #endif
  1802. //
  1803. // TinyBoy2 128x64 OLED / Encoder Panel
  1804. //
  1805. //#define OLED_PANEL_TINYBOY2
  1806. //
  1807. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1808. // http://reprap.org/wiki/MKS_12864OLED
  1809. //
  1810. // Tiny, but very sharp OLED display
  1811. //
  1812. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1813. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1814. //
  1815. // Einstart S OLED SSD1306
  1816. //
  1817. //#define U8GLIB_SH1106_EINSTART
  1818. //
  1819. // Overlord OLED display/controller with i2c buzzer and LEDs
  1820. //
  1821. //#define OVERLORD_OLED
  1822. //=============================================================================
  1823. //========================== Extensible UI Displays ===========================
  1824. //=============================================================================
  1825. //
  1826. // DGUS Touch Display with DWIN OS
  1827. //
  1828. //#define DGUS_LCD
  1829. //
  1830. // Touch-screen LCD for Malyan M200 printers
  1831. //
  1832. //#define MALYAN_LCD
  1833. //
  1834. // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
  1835. // See Configuration_adv.h for all configuration options.
  1836. //
  1837. //#define LULZBOT_TOUCH_UI
  1838. //
  1839. // Third-party or vendor-customized controller interfaces.
  1840. // Sources should be installed in 'src/lcd/extensible_ui'.
  1841. //
  1842. //#define EXTENSIBLE_UI
  1843. //=============================================================================
  1844. //=============================== Graphical TFTs ==============================
  1845. //=============================================================================
  1846. //
  1847. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1848. //
  1849. //#define FSMC_GRAPHICAL_TFT
  1850. //=============================================================================
  1851. //============================ Other Controllers ============================
  1852. //=============================================================================
  1853. //
  1854. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1855. //
  1856. //#define TOUCH_BUTTONS
  1857. #if ENABLED(TOUCH_BUTTONS)
  1858. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  1859. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  1860. #define XPT2046_X_CALIBRATION 12316
  1861. #define XPT2046_Y_CALIBRATION -8981
  1862. #define XPT2046_X_OFFSET -43
  1863. #define XPT2046_Y_OFFSET 257
  1864. #endif
  1865. //
  1866. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1867. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1868. //
  1869. //#define REPRAPWORLD_KEYPAD
  1870. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1871. //=============================================================================
  1872. //=============================== Extra Features ==============================
  1873. //=============================================================================
  1874. // @section extras
  1875. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1876. //#define FAST_PWM_FAN
  1877. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1878. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1879. // is too low, you should also increment SOFT_PWM_SCALE.
  1880. //#define FAN_SOFT_PWM
  1881. // Incrementing this by 1 will double the software PWM frequency,
  1882. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1883. // However, control resolution will be halved for each increment;
  1884. // at zero value, there are 128 effective control positions.
  1885. // :[0,1,2,3,4,5,6,7]
  1886. #define SOFT_PWM_SCALE 0
  1887. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1888. // be used to mitigate the associated resolution loss. If enabled,
  1889. // some of the PWM cycles are stretched so on average the desired
  1890. // duty cycle is attained.
  1891. //#define SOFT_PWM_DITHER
  1892. // Temperature status LEDs that display the hotend and bed temperature.
  1893. // If all hotends, bed temperature, and target temperature are under 54C
  1894. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1895. //#define TEMP_STAT_LEDS
  1896. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1897. //#define SF_ARC_FIX
  1898. // Support for the BariCUDA Paste Extruder
  1899. //#define BARICUDA
  1900. // Support for BlinkM/CyzRgb
  1901. //#define BLINKM
  1902. // Support for PCA9632 PWM LED driver
  1903. //#define PCA9632
  1904. // Support for PCA9533 PWM LED driver
  1905. // https://github.com/mikeshub/SailfishRGB_LED
  1906. //#define PCA9533
  1907. /**
  1908. * RGB LED / LED Strip Control
  1909. *
  1910. * Enable support for an RGB LED connected to 5V digital pins, or
  1911. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1912. *
  1913. * Adds the M150 command to set the LED (or LED strip) color.
  1914. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1915. * luminance values can be set from 0 to 255.
  1916. * For Neopixel LED an overall brightness parameter is also available.
  1917. *
  1918. * *** CAUTION ***
  1919. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1920. * as the Arduino cannot handle the current the LEDs will require.
  1921. * Failure to follow this precaution can destroy your Arduino!
  1922. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1923. * more current than the Arduino 5V linear regulator can produce.
  1924. * *** CAUTION ***
  1925. *
  1926. * LED Type. Enable only one of the following two options.
  1927. *
  1928. */
  1929. //#define RGB_LED
  1930. //#define RGBW_LED
  1931. #if EITHER(RGB_LED, RGBW_LED)
  1932. //#define RGB_LED_R_PIN 34
  1933. //#define RGB_LED_G_PIN 43
  1934. //#define RGB_LED_B_PIN 35
  1935. //#define RGB_LED_W_PIN -1
  1936. #endif
  1937. // Support for Adafruit Neopixel LED driver
  1938. //#define NEOPIXEL_LED
  1939. #if ENABLED(NEOPIXEL_LED)
  1940. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1941. #define NEOPIXEL_PIN 4 // LED driving pin
  1942. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1943. //#define NEOPIXEL2_PIN 5
  1944. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1945. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1946. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1947. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1948. // Use a single Neopixel LED for static (background) lighting
  1949. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1950. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1951. #endif
  1952. /**
  1953. * Printer Event LEDs
  1954. *
  1955. * During printing, the LEDs will reflect the printer status:
  1956. *
  1957. * - Gradually change from blue to violet as the heated bed gets to target temp
  1958. * - Gradually change from violet to red as the hotend gets to temperature
  1959. * - Change to white to illuminate work surface
  1960. * - Change to green once print has finished
  1961. * - Turn off after the print has finished and the user has pushed a button
  1962. */
  1963. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1964. #define PRINTER_EVENT_LEDS
  1965. #endif
  1966. /**
  1967. * R/C SERVO support
  1968. * Sponsored by TrinityLabs, Reworked by codexmas
  1969. */
  1970. /**
  1971. * Number of servos
  1972. *
  1973. * For some servo-related options NUM_SERVOS will be set automatically.
  1974. * Set this manually if there are extra servos needing manual control.
  1975. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1976. */
  1977. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1978. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  1979. // 300ms is a good value but you can try less delay.
  1980. // If the servo can't reach the requested position, increase it.
  1981. #define SERVO_DELAY { 300 }
  1982. // Only power servos during movement, otherwise leave off to prevent jitter
  1983. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1984. // Allow servo angle to be edited and saved to EEPROM
  1985. //#define EDITABLE_SERVO_ANGLES