My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 92KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497149814991500150115021503150415051506150715081509151015111512151315141515151615171518151915201521152215231524152515261527152815291530153115321533153415351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563156415651566156715681569157015711572157315741575157615771578157915801581158215831584158515861587158815891590159115921593159415951596159715981599160016011602160316041605160616071608160916101611161216131614161516161617161816191620162116221623162416251626162716281629163016311632163316341635163616371638163916401641164216431644164516461647164816491650165116521653165416551656165716581659166016611662166316641665166616671668166916701671167216731674167516761677167816791680168116821683168416851686168716881689169016911692169316941695169616971698169917001701170217031704170517061707170817091710171117121713171417151716171717181719172017211722172317241725172617271728172917301731173217331734173517361737173817391740174117421743174417451746174717481749175017511752175317541755175617571758175917601761176217631764176517661767176817691770177117721773177417751776177717781779178017811782178317841785178617871788178917901791179217931794179517961797179817991800180118021803180418051806180718081809181018111812181318141815181618171818181918201821182218231824182518261827182818291830183118321833183418351836183718381839184018411842184318441845184618471848184918501851185218531854185518561857185818591860186118621863186418651866186718681869187018711872187318741875187618771878187918801881188218831884188518861887188818891890189118921893189418951896189718981899190019011902190319041905190619071908190919101911191219131914191519161917191819191920192119221923192419251926192719281929193019311932193319341935193619371938193919401941194219431944194519461947194819491950195119521953195419551956195719581959196019611962196319641965196619671968196919701971197219731974197519761977197819791980198119821983198419851986198719881989199019911992199319941995199619971998199920002001200220032004200520062007200820092010201120122013201420152016201720182019202020212022202320242025202620272028202920302031203220332034203520362037203820392040204120422043204420452046204720482049205020512052205320542055205620572058205920602061206220632064206520662067206820692070207120722073207420752076207720782079208020812082208320842085208620872088208920902091209220932094209520962097209820992100210121022103210421052106210721082109211021112112211321142115211621172118211921202121212221232124212521262127212821292130213121322133213421352136213721382139214021412142214321442145214621472148214921502151215221532154215521562157215821592160216121622163216421652166216721682169217021712172217321742175217621772178217921802181218221832184218521862187218821892190219121922193219421952196219721982199220022012202220322042205220622072208220922102211221222132214221522162217221822192220222122222223222422252226222722282229223022312232223322342235223622372238223922402241224222432244224522462247224822492250225122522253225422552256225722582259226022612262226322642265226622672268226922702271227222732274227522762277227822792280228122822283228422852286228722882289229022912292229322942295229622972298229923002301230223032304230523062307230823092310231123122313231423152316231723182319232023212322232323242325232623272328232923302331233223332334233523362337233823392340234123422343234423452346234723482349235023512352235323542355235623572358235923602361236223632364236523662367236823692370237123722373237423752376237723782379238023812382238323842385238623872388238923902391239223932394239523962397239823992400240124022403240424052406240724082409241024112412241324142415241624172418241924202421242224232424242524262427242824292430243124322433243424352436243724382439244024412442244324442445244624472448244924502451245224532454245524562457245824592460246124622463246424652466246724682469247024712472247324742475247624772478247924802481248224832484248524862487248824892490249124922493249424952496249724982499250025012502250325042505250625072508250925102511251225132514251525162517251825192520252125222523252425252526252725282529253025312532253325342535253625372538253925402541254225432544254525462547254825492550
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. */
  37. #define CONFIGURATION_H_VERSION 020008
  38. //===========================================================================
  39. //============================= Getting Started =============================
  40. //===========================================================================
  41. /**
  42. * Here are some standard links for getting your machine calibrated:
  43. *
  44. * https://reprap.org/wiki/Calibration
  45. * https://youtu.be/wAL9d7FgInk
  46. * http://calculator.josefprusa.cz
  47. * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  48. * https://www.thingiverse.com/thing:5573
  49. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  50. * https://www.thingiverse.com/thing:298812
  51. */
  52. //===========================================================================
  53. //============================= DELTA Printer ===============================
  54. //===========================================================================
  55. // For a Delta printer, start with one of the configuration files in the config/examples/delta directory
  56. // from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine.
  57. //
  58. //===========================================================================
  59. //============================= SCARA Printer ===============================
  60. //===========================================================================
  61. // For a SCARA printer, start with one of the configuration files in the config/examples/SCARA directory
  62. // from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine.
  63. //
  64. // @section info
  65. // Author info of this build printed to the host during boot and M115
  66. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  67. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  68. /**
  69. * *** VENDORS PLEASE READ ***
  70. *
  71. * Marlin allows you to add a custom boot image for Graphical LCDs.
  72. * With this option Marlin will first show your custom screen followed
  73. * by the standard Marlin logo with version number and web URL.
  74. *
  75. * We encourage you to take advantage of this new feature and we also
  76. * respectfully request that you retain the unmodified Marlin boot screen.
  77. */
  78. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  79. #define SHOW_BOOTSCREEN
  80. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  81. //#define SHOW_CUSTOM_BOOTSCREEN
  82. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  83. //#define CUSTOM_STATUS_SCREEN_IMAGE
  84. // @section machine
  85. /**
  86. * Select the serial port on the board to use for communication with the host.
  87. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  88. * Serial port -1 is the USB emulated serial port, if available.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  97. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  98. */
  99. //#define SERIAL_PORT_2 -1
  100. /**
  101. * This setting determines the communication speed of the printer.
  102. *
  103. * 250000 works in most cases, but you might try a lower speed if
  104. * you commonly experience drop-outs during host printing.
  105. * You may try up to 1000000 to speed up SD file transfer.
  106. *
  107. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  108. */
  109. #define BAUDRATE 250000
  110. // Enable the Bluetooth serial interface on AT90USB devices
  111. //#define BLUETOOTH
  112. // Choose the name from boards.h that matches your setup
  113. #ifndef MOTHERBOARD
  114. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  115. #endif
  116. // Name displayed in the LCD "Ready" message and Info menu
  117. //#define CUSTOM_MACHINE_NAME "3D Printer"
  118. // Printer's unique ID, used by some programs to differentiate between machines.
  119. // Choose your own or use a service like https://www.uuidgenerator.net/version4
  120. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  121. // @section extruder
  122. // This defines the number of extruders
  123. // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
  124. #define EXTRUDERS 1
  125. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  126. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  127. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  128. //#define SINGLENOZZLE
  129. // Save and restore temperature and fan speed on tool-change.
  130. // Set standby for the unselected tool with M104/106/109 T...
  131. #if ENABLED(SINGLENOZZLE)
  132. //#define SINGLENOZZLE_STANDBY_TEMP
  133. //#define SINGLENOZZLE_STANDBY_FAN
  134. #endif
  135. /**
  136. * Multi-Material Unit
  137. * Set to one of these predefined models:
  138. *
  139. * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version)
  140. * PRUSA_MMU2 : Průša MMU2
  141. * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
  142. * SMUFF_EMU_MMU2 : Technik Gegg SMUFF (Průša MMU2 emulation mode)
  143. * SMUFF_EMU_MMU2S : Technik Gegg SMUFF (Průša MMU2S emulation mode)
  144. *
  145. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  146. * See additional options in Configuration_adv.h.
  147. */
  148. //#define MMU_MODEL PRUSA_MMU2
  149. // A dual extruder that uses a single stepper motor
  150. //#define SWITCHING_EXTRUDER
  151. #if ENABLED(SWITCHING_EXTRUDER)
  152. #define SWITCHING_EXTRUDER_SERVO_NR 0
  153. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  154. #if EXTRUDERS > 3
  155. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  156. #endif
  157. #endif
  158. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  159. //#define SWITCHING_NOZZLE
  160. #if ENABLED(SWITCHING_NOZZLE)
  161. #define SWITCHING_NOZZLE_SERVO_NR 0
  162. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  163. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  164. #endif
  165. /**
  166. * Two separate X-carriages with extruders that connect to a moving part
  167. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  168. */
  169. //#define PARKING_EXTRUDER
  170. /**
  171. * Two separate X-carriages with extruders that connect to a moving part
  172. * via a magnetic docking mechanism using movements and no solenoid
  173. *
  174. * project : https://www.thingiverse.com/thing:3080893
  175. * movements : https://youtu.be/0xCEiG9VS3k
  176. * https://youtu.be/Bqbcs0CU2FE
  177. */
  178. //#define MAGNETIC_PARKING_EXTRUDER
  179. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  180. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  181. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  182. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  183. #if ENABLED(PARKING_EXTRUDER)
  184. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  185. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  186. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  187. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  188. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  189. #define MPE_FAST_SPEED 9000 // (mm/min) Speed for travel before last distance point
  190. #define MPE_SLOW_SPEED 4500 // (mm/min) Speed for last distance travel to park and couple
  191. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  192. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  193. #endif
  194. #endif
  195. /**
  196. * Switching Toolhead
  197. *
  198. * Support for swappable and dockable toolheads, such as
  199. * the E3D Tool Changer. Toolheads are locked with a servo.
  200. */
  201. //#define SWITCHING_TOOLHEAD
  202. /**
  203. * Magnetic Switching Toolhead
  204. *
  205. * Support swappable and dockable toolheads with a magnetic
  206. * docking mechanism using movement and no servo.
  207. */
  208. //#define MAGNETIC_SWITCHING_TOOLHEAD
  209. /**
  210. * Electromagnetic Switching Toolhead
  211. *
  212. * Parking for CoreXY / HBot kinematics.
  213. * Toolheads are parked at one edge and held with an electromagnet.
  214. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  215. */
  216. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  217. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  218. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  219. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  220. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  221. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  222. #if ENABLED(SWITCHING_TOOLHEAD)
  223. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  224. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  225. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  226. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  227. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  228. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  229. #if ENABLED(PRIME_BEFORE_REMOVE)
  230. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  231. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  232. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/min) Extruder prime feedrate
  233. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/min) Extruder retract feedrate
  234. #endif
  235. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  236. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  237. #endif
  238. #endif
  239. /**
  240. * "Mixing Extruder"
  241. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  242. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  243. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  244. * - This implementation supports up to two mixing extruders.
  245. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  246. */
  247. //#define MIXING_EXTRUDER
  248. #if ENABLED(MIXING_EXTRUDER)
  249. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  250. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  251. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  252. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  253. #if ENABLED(GRADIENT_MIX)
  254. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  255. #endif
  256. #endif
  257. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  258. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  259. // For the other hotends it is their distance from the extruder 0 hotend.
  260. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  261. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  262. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  263. // @section machine
  264. /**
  265. * Power Supply Control
  266. *
  267. * Enable and connect the power supply to the PS_ON_PIN.
  268. * Specify whether the power supply is active HIGH or active LOW.
  269. */
  270. //#define PSU_CONTROL
  271. //#define PSU_NAME "Power Supply"
  272. #if ENABLED(PSU_CONTROL)
  273. #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box
  274. //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
  275. //#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power
  276. //#define PSU_POWERUP_GCODE "M355 S1" // G-code to run after power-on (e.g., case light on)
  277. //#define PSU_POWEROFF_GCODE "M355 S0" // G-code to run before power-off (e.g., case light off)
  278. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  279. #if ENABLED(AUTO_POWER_CONTROL)
  280. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  281. #define AUTO_POWER_E_FANS
  282. #define AUTO_POWER_CONTROLLERFAN
  283. #define AUTO_POWER_CHAMBER_FAN
  284. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU if any extruder is over this temperature
  285. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU if the chamber is over this temperature
  286. #define POWER_TIMEOUT 30 // (s) Turn off power if the machine is idle for this duration
  287. //#define POWER_OFF_DELAY 60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
  288. #endif
  289. #endif
  290. //===========================================================================
  291. //============================= Thermal Settings ============================
  292. //===========================================================================
  293. // @section temperature
  294. /**
  295. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  296. *
  297. * Temperature sensors available:
  298. *
  299. * -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
  300. * -3 : thermocouple with MAX31855 (only for sensors 0-1)
  301. * -2 : thermocouple with MAX6675 (only for sensors 0-1)
  302. * -4 : thermocouple with AD8495
  303. * -1 : thermocouple with AD595
  304. * 0 : not used
  305. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  306. * 331 : (3.3V scaled thermistor 1 table for MEGA)
  307. * 332 : (3.3V scaled thermistor 1 table for DUE)
  308. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  309. * 202 : 200k thermistor - Copymaster 3D
  310. * 3 : Mendel-parts thermistor (4.7k pullup)
  311. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  312. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
  313. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  314. * 502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
  315. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  316. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  317. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  318. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  319. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  320. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  321. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  322. * 11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
  323. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  324. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  325. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  326. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  327. * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  328. * NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
  329. * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
  330. * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  331. * 22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
  332. * 23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
  333. * 30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
  334. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  335. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  336. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  337. * 66 : 4.7M High Temperature thermistor from Dyze Design
  338. * 67 : 450C thermistor from SliceEngineering
  339. * 70 : the 100K thermistor found in the bq Hephestos 2
  340. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  341. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  342. *
  343. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  344. * (but gives greater accuracy and more stable PID)
  345. * 51 : 100k thermistor - EPCOS (1k pullup)
  346. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  347. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  348. *
  349. * 1047 : Pt1000 with 4k7 pullup (E3D)
  350. * 1010 : Pt1000 with 1k pullup (non standard)
  351. * 147 : Pt100 with 4k7 pullup
  352. * 110 : Pt100 with 1k pullup (non standard)
  353. *
  354. * 1000 : Custom - Specify parameters in Configuration_adv.h
  355. *
  356. * Use these for Testing or Development purposes. NEVER for production machine.
  357. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  358. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  359. */
  360. #define TEMP_SENSOR_0 1
  361. #define TEMP_SENSOR_1 0
  362. #define TEMP_SENSOR_2 0
  363. #define TEMP_SENSOR_3 0
  364. #define TEMP_SENSOR_4 0
  365. #define TEMP_SENSOR_5 0
  366. #define TEMP_SENSOR_6 0
  367. #define TEMP_SENSOR_7 0
  368. #define TEMP_SENSOR_BED 0
  369. #define TEMP_SENSOR_PROBE 0
  370. #define TEMP_SENSOR_CHAMBER 0
  371. // Dummy thermistor constant temperature readings, for use with 998 and 999
  372. #define DUMMY_THERMISTOR_998_VALUE 25
  373. #define DUMMY_THERMISTOR_999_VALUE 100
  374. // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
  375. //#define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000)
  376. //#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for AdaFruit PT100; 4300 for AdaFruit PT1000
  377. //#define MAX31865_SENSOR_OHMS_1 100
  378. //#define MAX31865_CALIBRATION_OHMS_1 430
  379. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  380. // from the two sensors differ too much the print will be aborted.
  381. //#define TEMP_SENSOR_1_AS_REDUNDANT
  382. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  383. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  384. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  385. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  386. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  387. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  388. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  389. // Below this temperature the heater will be switched off
  390. // because it probably indicates a broken thermistor wire.
  391. #define HEATER_0_MINTEMP 5
  392. #define HEATER_1_MINTEMP 5
  393. #define HEATER_2_MINTEMP 5
  394. #define HEATER_3_MINTEMP 5
  395. #define HEATER_4_MINTEMP 5
  396. #define HEATER_5_MINTEMP 5
  397. #define HEATER_6_MINTEMP 5
  398. #define HEATER_7_MINTEMP 5
  399. #define BED_MINTEMP 5
  400. // Above this temperature the heater will be switched off.
  401. // This can protect components from overheating, but NOT from shorts and failures.
  402. // (Use MINTEMP for thermistor short/failure protection.)
  403. #define HEATER_0_MAXTEMP 275
  404. #define HEATER_1_MAXTEMP 275
  405. #define HEATER_2_MAXTEMP 275
  406. #define HEATER_3_MAXTEMP 275
  407. #define HEATER_4_MAXTEMP 275
  408. #define HEATER_5_MAXTEMP 275
  409. #define HEATER_6_MAXTEMP 275
  410. #define HEATER_7_MAXTEMP 275
  411. #define BED_MAXTEMP 150
  412. //===========================================================================
  413. //============================= PID Settings ================================
  414. //===========================================================================
  415. // PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning
  416. // Comment the following line to disable PID and enable bang-bang.
  417. #define PIDTEMP
  418. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  419. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  420. #define PID_K1 0.95 // Smoothing factor within any PID loop
  421. #if ENABLED(PIDTEMP)
  422. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  423. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  424. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  425. // Set/get with gcode: M301 E[extruder number, 0-2]
  426. #if ENABLED(PID_PARAMS_PER_HOTEND)
  427. // Specify between 1 and HOTENDS values per array.
  428. // If fewer than EXTRUDER values are provided, the last element will be repeated.
  429. #define DEFAULT_Kp_LIST { 22.20, 22.20 }
  430. #define DEFAULT_Ki_LIST { 1.08, 1.08 }
  431. #define DEFAULT_Kd_LIST { 114.00, 114.00 }
  432. #else
  433. #define DEFAULT_Kp 22.20
  434. #define DEFAULT_Ki 1.08
  435. #define DEFAULT_Kd 114.00
  436. #endif
  437. #endif // PIDTEMP
  438. //===========================================================================
  439. //====================== PID > Bed Temperature Control ======================
  440. //===========================================================================
  441. /**
  442. * PID Bed Heating
  443. *
  444. * If this option is enabled set PID constants below.
  445. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  446. *
  447. * The PID frequency will be the same as the extruder PWM.
  448. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  449. * which is fine for driving a square wave into a resistive load and does not significantly
  450. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  451. * heater. If your configuration is significantly different than this and you don't understand
  452. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  453. */
  454. //#define PIDTEMPBED
  455. //#define BED_LIMIT_SWITCHING
  456. /**
  457. * Max Bed Power
  458. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  459. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  460. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  461. */
  462. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  463. #if ENABLED(PIDTEMPBED)
  464. //#define MIN_BED_POWER 0
  465. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  466. // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  467. // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  468. #define DEFAULT_bedKp 10.00
  469. #define DEFAULT_bedKi .023
  470. #define DEFAULT_bedKd 305.4
  471. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  472. #endif // PIDTEMPBED
  473. #if EITHER(PIDTEMP, PIDTEMPBED)
  474. //#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
  475. //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  476. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  477. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  478. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  479. #endif
  480. // @section extruder
  481. /**
  482. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  483. * Add M302 to set the minimum extrusion temperature and/or turn
  484. * cold extrusion prevention on and off.
  485. *
  486. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  487. */
  488. #define PREVENT_COLD_EXTRUSION
  489. #define EXTRUDE_MINTEMP 170
  490. /**
  491. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  492. * Note: For Bowden Extruders make this large enough to allow load/unload.
  493. */
  494. #define PREVENT_LENGTHY_EXTRUDE
  495. #define EXTRUDE_MAXLENGTH 200
  496. //===========================================================================
  497. //======================== Thermal Runaway Protection =======================
  498. //===========================================================================
  499. /**
  500. * Thermal Protection provides additional protection to your printer from damage
  501. * and fire. Marlin always includes safe min and max temperature ranges which
  502. * protect against a broken or disconnected thermistor wire.
  503. *
  504. * The issue: If a thermistor falls out, it will report the much lower
  505. * temperature of the air in the room, and the the firmware will keep
  506. * the heater on.
  507. *
  508. * If you get "Thermal Runaway" or "Heating failed" errors the
  509. * details can be tuned in Configuration_adv.h
  510. */
  511. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  512. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  513. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  514. //===========================================================================
  515. //============================= Mechanical Settings =========================
  516. //===========================================================================
  517. // @section machine
  518. // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
  519. // either in the usual order or reversed
  520. //#define COREXY
  521. //#define COREXZ
  522. //#define COREYZ
  523. //#define COREYX
  524. //#define COREZX
  525. //#define COREZY
  526. //#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042
  527. //===========================================================================
  528. //============================== Endstop Settings ===========================
  529. //===========================================================================
  530. // @section homing
  531. // Specify here all the endstop connectors that are connected to any endstop or probe.
  532. // Almost all printers will be using one per axis. Probes will use one or more of the
  533. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  534. #define USE_XMIN_PLUG
  535. #define USE_YMIN_PLUG
  536. #define USE_ZMIN_PLUG
  537. //#define USE_XMAX_PLUG
  538. //#define USE_YMAX_PLUG
  539. //#define USE_ZMAX_PLUG
  540. // Enable pullup for all endstops to prevent a floating state
  541. #define ENDSTOPPULLUPS
  542. #if DISABLED(ENDSTOPPULLUPS)
  543. // Disable ENDSTOPPULLUPS to set pullups individually
  544. //#define ENDSTOPPULLUP_XMAX
  545. //#define ENDSTOPPULLUP_YMAX
  546. //#define ENDSTOPPULLUP_ZMAX
  547. //#define ENDSTOPPULLUP_XMIN
  548. //#define ENDSTOPPULLUP_YMIN
  549. //#define ENDSTOPPULLUP_ZMIN
  550. //#define ENDSTOPPULLUP_ZMIN_PROBE
  551. #endif
  552. // Enable pulldown for all endstops to prevent a floating state
  553. //#define ENDSTOPPULLDOWNS
  554. #if DISABLED(ENDSTOPPULLDOWNS)
  555. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  556. //#define ENDSTOPPULLDOWN_XMAX
  557. //#define ENDSTOPPULLDOWN_YMAX
  558. //#define ENDSTOPPULLDOWN_ZMAX
  559. //#define ENDSTOPPULLDOWN_XMIN
  560. //#define ENDSTOPPULLDOWN_YMIN
  561. //#define ENDSTOPPULLDOWN_ZMIN
  562. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  563. #endif
  564. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  565. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  566. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  567. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  568. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  569. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  570. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  571. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  572. /**
  573. * Stepper Drivers
  574. *
  575. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  576. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  577. *
  578. * A4988 is assumed for unspecified drivers.
  579. *
  580. * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  581. *
  582. * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
  583. * TB6560, TB6600, TMC2100,
  584. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  585. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  586. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  587. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  588. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  589. */
  590. #define X_DRIVER_TYPE A4988
  591. #define Y_DRIVER_TYPE A4988
  592. #define Z_DRIVER_TYPE A4988
  593. //#define X2_DRIVER_TYPE A4988
  594. //#define Y2_DRIVER_TYPE A4988
  595. //#define Z2_DRIVER_TYPE A4988
  596. //#define Z3_DRIVER_TYPE A4988
  597. //#define Z4_DRIVER_TYPE A4988
  598. #define E0_DRIVER_TYPE A4988
  599. //#define E1_DRIVER_TYPE A4988
  600. //#define E2_DRIVER_TYPE A4988
  601. //#define E3_DRIVER_TYPE A4988
  602. //#define E4_DRIVER_TYPE A4988
  603. //#define E5_DRIVER_TYPE A4988
  604. //#define E6_DRIVER_TYPE A4988
  605. //#define E7_DRIVER_TYPE A4988
  606. // Enable this feature if all enabled endstop pins are interrupt-capable.
  607. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  608. //#define ENDSTOP_INTERRUPTS_FEATURE
  609. /**
  610. * Endstop Noise Threshold
  611. *
  612. * Enable if your probe or endstops falsely trigger due to noise.
  613. *
  614. * - Higher values may affect repeatability or accuracy of some bed probes.
  615. * - To fix noise install a 100nF ceramic capacitor in parallel with the switch.
  616. * - This feature is not required for common micro-switches mounted on PCBs
  617. * based on the Makerbot design, which already have the 100nF capacitor.
  618. *
  619. * :[2,3,4,5,6,7]
  620. */
  621. //#define ENDSTOP_NOISE_THRESHOLD 2
  622. // Check for stuck or disconnected endstops during homing moves.
  623. //#define DETECT_BROKEN_ENDSTOP
  624. //=============================================================================
  625. //============================== Movement Settings ============================
  626. //=============================================================================
  627. // @section motion
  628. /**
  629. * Default Settings
  630. *
  631. * These settings can be reset by M502
  632. *
  633. * Note that if EEPROM is enabled, saved values will override these.
  634. */
  635. /**
  636. * With this option each E stepper can have its own factors for the
  637. * following movement settings. If fewer factors are given than the
  638. * total number of extruders, the last value applies to the rest.
  639. */
  640. //#define DISTINCT_E_FACTORS
  641. /**
  642. * Default Axis Steps Per Unit (steps/mm)
  643. * Override with M92
  644. * X, Y, Z, E0 [, E1[, E2...]]
  645. */
  646. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
  647. /**
  648. * Default Max Feed Rate (mm/s)
  649. * Override with M203
  650. * X, Y, Z, E0 [, E1[, E2...]]
  651. */
  652. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  653. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  654. #if ENABLED(LIMITED_MAX_FR_EDITING)
  655. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  656. #endif
  657. /**
  658. * Default Max Acceleration (change/s) change = mm/s
  659. * (Maximum start speed for accelerated moves)
  660. * Override with M201
  661. * X, Y, Z, E0 [, E1[, E2...]]
  662. */
  663. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  664. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  665. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  666. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  667. #endif
  668. /**
  669. * Default Acceleration (change/s) change = mm/s
  670. * Override with M204
  671. *
  672. * M204 P Acceleration
  673. * M204 R Retract Acceleration
  674. * M204 T Travel Acceleration
  675. */
  676. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  677. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  678. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  679. /**
  680. * Default Jerk limits (mm/s)
  681. * Override with M205 X Y Z E
  682. *
  683. * "Jerk" specifies the minimum speed change that requires acceleration.
  684. * When changing speed and direction, if the difference is less than the
  685. * value set here, it may happen instantaneously.
  686. */
  687. //#define CLASSIC_JERK
  688. #if ENABLED(CLASSIC_JERK)
  689. #define DEFAULT_XJERK 10.0
  690. #define DEFAULT_YJERK 10.0
  691. #define DEFAULT_ZJERK 0.3
  692. //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
  693. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  694. #if ENABLED(LIMITED_JERK_EDITING)
  695. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  696. #endif
  697. #endif
  698. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  699. /**
  700. * Junction Deviation Factor
  701. *
  702. * See:
  703. * https://reprap.org/forum/read.php?1,739819
  704. * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  705. */
  706. #if DISABLED(CLASSIC_JERK)
  707. #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
  708. #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
  709. // for small segments (< 1mm) with large junction angles (> 135°).
  710. #endif
  711. /**
  712. * S-Curve Acceleration
  713. *
  714. * This option eliminates vibration during printing by fitting a Bézier
  715. * curve to move acceleration, producing much smoother direction changes.
  716. *
  717. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  718. */
  719. //#define S_CURVE_ACCELERATION
  720. //===========================================================================
  721. //============================= Z Probe Options =============================
  722. //===========================================================================
  723. // @section probes
  724. //
  725. // See https://marlinfw.org/docs/configuration/probes.html
  726. //
  727. /**
  728. * Enable this option for a probe connected to the Z-MIN pin.
  729. * The probe replaces the Z-MIN endstop and is used for Z homing.
  730. * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  731. */
  732. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  733. // Force the use of the probe for Z-axis homing
  734. //#define USE_PROBE_FOR_Z_HOMING
  735. /**
  736. * Z_MIN_PROBE_PIN
  737. *
  738. * Define this pin if the probe is not connected to Z_MIN_PIN.
  739. * If not defined the default pin for the selected MOTHERBOARD
  740. * will be used. Most of the time the default is what you want.
  741. *
  742. * - The simplest option is to use a free endstop connector.
  743. * - Use 5V for powered (usually inductive) sensors.
  744. *
  745. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  746. * - For simple switches connect...
  747. * - normally-closed switches to GND and D32.
  748. * - normally-open switches to 5V and D32.
  749. */
  750. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  751. /**
  752. * Probe Type
  753. *
  754. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  755. * Activate one of these to use Auto Bed Leveling below.
  756. */
  757. /**
  758. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  759. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  760. * or (with LCD_BED_LEVELING) the LCD controller.
  761. */
  762. //#define PROBE_MANUALLY
  763. //#define MANUAL_PROBE_START_Z 0.2
  764. /**
  765. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  766. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  767. */
  768. //#define FIX_MOUNTED_PROBE
  769. /**
  770. * Use the nozzle as the probe, as with a conductive
  771. * nozzle system or a piezo-electric smart effector.
  772. */
  773. //#define NOZZLE_AS_PROBE
  774. /**
  775. * Z Servo Probe, such as an endstop switch on a rotating arm.
  776. */
  777. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  778. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  779. /**
  780. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  781. */
  782. //#define BLTOUCH
  783. /**
  784. * Pressure sensor with a BLTouch-like interface
  785. */
  786. //#define CREALITY_TOUCH
  787. /**
  788. * Touch-MI Probe by hotends.fr
  789. *
  790. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  791. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  792. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  793. *
  794. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  795. * and a minimum Z_HOMING_HEIGHT of 10.
  796. */
  797. //#define TOUCH_MI_PROBE
  798. #if ENABLED(TOUCH_MI_PROBE)
  799. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  800. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  801. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  802. #endif
  803. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  804. //#define SOLENOID_PROBE
  805. // A sled-mounted probe like those designed by Charles Bell.
  806. //#define Z_PROBE_SLED
  807. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  808. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  809. //#define RACK_AND_PINION_PROBE
  810. #if ENABLED(RACK_AND_PINION_PROBE)
  811. #define Z_PROBE_DEPLOY_X X_MIN_POS
  812. #define Z_PROBE_RETRACT_X X_MAX_POS
  813. #endif
  814. // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
  815. // When the pin is defined you can use M672 to set/reset the probe sensivity.
  816. //#define DUET_SMART_EFFECTOR
  817. #if ENABLED(DUET_SMART_EFFECTOR)
  818. #define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin
  819. #endif
  820. /**
  821. * Use StallGuard2 to probe the bed with the nozzle.
  822. * Requires stallGuard-capable Trinamic stepper drivers.
  823. * CAUTION: This can damage machines with Z lead screws.
  824. * Take extreme care when setting up this feature.
  825. */
  826. //#define SENSORLESS_PROBING
  827. //
  828. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  829. //
  830. /**
  831. * Nozzle-to-Probe offsets { X, Y, Z }
  832. *
  833. * X and Y offset
  834. * Use a caliper or ruler to measure the distance from the tip of
  835. * the Nozzle to the center-point of the Probe in the X and Y axes.
  836. *
  837. * Z offset
  838. * - For the Z offset use your best known value and adjust at runtime.
  839. * - Common probes trigger below the nozzle and have negative values for Z offset.
  840. * - Probes triggering above the nozzle height are uncommon but do exist. When using
  841. * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES
  842. * to avoid collisions during probing.
  843. *
  844. * Tune and Adjust
  845. * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc.
  846. * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset.
  847. *
  848. * Assuming the typical work area orientation:
  849. * - Probe to RIGHT of the Nozzle has a Positive X offset
  850. * - Probe to LEFT of the Nozzle has a Negative X offset
  851. * - Probe in BACK of the Nozzle has a Positive Y offset
  852. * - Probe in FRONT of the Nozzle has a Negative Y offset
  853. *
  854. * Some examples:
  855. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 } // Example "1"
  856. * #define NOZZLE_TO_PROBE_OFFSET {-10, 5, -1 } // Example "2"
  857. * #define NOZZLE_TO_PROBE_OFFSET { 5, -5, -1 } // Example "3"
  858. * #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 } // Example "4"
  859. *
  860. * +-- BACK ---+
  861. * | [+] |
  862. * L | 1 | R <-- Example "1" (right+, back+)
  863. * E | 2 | I <-- Example "2" ( left-, back+)
  864. * F |[-] N [+]| G <-- Nozzle
  865. * T | 3 | H <-- Example "3" (right+, front-)
  866. * | 4 | T <-- Example "4" ( left-, front-)
  867. * | [-] |
  868. * O-- FRONT --+
  869. */
  870. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  871. // Most probes should stay away from the edges of the bed, but
  872. // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
  873. #define PROBING_MARGIN 10
  874. // X and Y axis travel speed (mm/min) between probes
  875. #define XY_PROBE_SPEED (133*60)
  876. // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  877. #define Z_PROBE_SPEED_FAST (4*60)
  878. // Feedrate (mm/min) for the "accurate" probe of each point
  879. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  880. /**
  881. * Multiple Probing
  882. *
  883. * You may get improved results by probing 2 or more times.
  884. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  885. *
  886. * A total of 2 does fast/slow probes with a weighted average.
  887. * A total of 3 or more adds more slow probes, taking the average.
  888. */
  889. //#define MULTIPLE_PROBING 2
  890. //#define EXTRA_PROBING 1
  891. /**
  892. * Z probes require clearance when deploying, stowing, and moving between
  893. * probe points to avoid hitting the bed and other hardware.
  894. * Servo-mounted probes require extra space for the arm to rotate.
  895. * Inductive probes need space to keep from triggering early.
  896. *
  897. * Use these settings to specify the distance (mm) to raise the probe (or
  898. * lower the bed). The values set here apply over and above any (negative)
  899. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  900. * Only integer values >= 1 are valid here.
  901. *
  902. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  903. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  904. */
  905. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  906. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  907. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  908. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  909. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  910. // For M851 give a range for adjusting the Z probe offset
  911. #define Z_PROBE_OFFSET_RANGE_MIN -20
  912. #define Z_PROBE_OFFSET_RANGE_MAX 20
  913. // Enable the M48 repeatability test to test probe accuracy
  914. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  915. // Before deploy/stow pause for user confirmation
  916. //#define PAUSE_BEFORE_DEPLOY_STOW
  917. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  918. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  919. #endif
  920. /**
  921. * Enable one or more of the following if probing seems unreliable.
  922. * Heaters and/or fans can be disabled during probing to minimize electrical
  923. * noise. A delay can also be added to allow noise and vibration to settle.
  924. * These options are most useful for the BLTouch probe, but may also improve
  925. * readings with inductive probes and piezo sensors.
  926. */
  927. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  928. #if ENABLED(PROBING_HEATERS_OFF)
  929. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  930. #endif
  931. //#define PROBING_FANS_OFF // Turn fans off when probing
  932. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  933. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  934. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  935. // :{ 0:'Low', 1:'High' }
  936. #define X_ENABLE_ON 0
  937. #define Y_ENABLE_ON 0
  938. #define Z_ENABLE_ON 0
  939. #define E_ENABLE_ON 0 // For all extruders
  940. // Disable axis steppers immediately when they're not being stepped.
  941. // WARNING: When motors turn off there is a chance of losing position accuracy!
  942. #define DISABLE_X false
  943. #define DISABLE_Y false
  944. #define DISABLE_Z false
  945. // Turn off the display blinking that warns about possible accuracy reduction
  946. //#define DISABLE_REDUCED_ACCURACY_WARNING
  947. // @section extruder
  948. #define DISABLE_E false // Disable the extruder when not stepping
  949. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  950. // @section machine
  951. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  952. #define INVERT_X_DIR false
  953. #define INVERT_Y_DIR true
  954. #define INVERT_Z_DIR false
  955. // @section extruder
  956. // For direct drive extruder v9 set to true, for geared extruder set to false.
  957. #define INVERT_E0_DIR false
  958. #define INVERT_E1_DIR false
  959. #define INVERT_E2_DIR false
  960. #define INVERT_E3_DIR false
  961. #define INVERT_E4_DIR false
  962. #define INVERT_E5_DIR false
  963. #define INVERT_E6_DIR false
  964. #define INVERT_E7_DIR false
  965. // @section homing
  966. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
  967. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
  968. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  969. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  970. // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
  971. //#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
  972. // Direction of endstops when homing; 1=MAX, -1=MIN
  973. // :[-1,1]
  974. #define X_HOME_DIR -1
  975. #define Y_HOME_DIR -1
  976. #define Z_HOME_DIR -1
  977. // @section machine
  978. // The size of the print bed
  979. #define X_BED_SIZE 200
  980. #define Y_BED_SIZE 200
  981. // Travel limits (mm) after homing, corresponding to endstop positions.
  982. #define X_MIN_POS 0
  983. #define Y_MIN_POS 0
  984. #define Z_MIN_POS 0
  985. #define X_MAX_POS X_BED_SIZE
  986. #define Y_MAX_POS Y_BED_SIZE
  987. #define Z_MAX_POS 200
  988. /**
  989. * Software Endstops
  990. *
  991. * - Prevent moves outside the set machine bounds.
  992. * - Individual axes can be disabled, if desired.
  993. * - X and Y only apply to Cartesian robots.
  994. * - Use 'M211' to set software endstops on/off or report current state
  995. */
  996. // Min software endstops constrain movement within minimum coordinate bounds
  997. #define MIN_SOFTWARE_ENDSTOPS
  998. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  999. #define MIN_SOFTWARE_ENDSTOP_X
  1000. #define MIN_SOFTWARE_ENDSTOP_Y
  1001. #define MIN_SOFTWARE_ENDSTOP_Z
  1002. #endif
  1003. // Max software endstops constrain movement within maximum coordinate bounds
  1004. #define MAX_SOFTWARE_ENDSTOPS
  1005. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  1006. #define MAX_SOFTWARE_ENDSTOP_X
  1007. #define MAX_SOFTWARE_ENDSTOP_Y
  1008. #define MAX_SOFTWARE_ENDSTOP_Z
  1009. #endif
  1010. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  1011. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  1012. #endif
  1013. /**
  1014. * Filament Runout Sensors
  1015. * Mechanical or opto endstops are used to check for the presence of filament.
  1016. *
  1017. * IMPORTANT: Runout will only trigger if Marlin is aware that a print job is running.
  1018. * Marlin knows a print job is running when:
  1019. * 1. Running a print job from media started with M24.
  1020. * 2. The Print Job Timer has been started with M75.
  1021. * 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled.
  1022. *
  1023. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  1024. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  1025. */
  1026. //#define FILAMENT_RUNOUT_SENSOR
  1027. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  1028. #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
  1029. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  1030. #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
  1031. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  1032. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  1033. // Override individually if the runout sensors vary
  1034. //#define FIL_RUNOUT1_STATE LOW
  1035. //#define FIL_RUNOUT1_PULLUP
  1036. //#define FIL_RUNOUT1_PULLDOWN
  1037. //#define FIL_RUNOUT2_STATE LOW
  1038. //#define FIL_RUNOUT2_PULLUP
  1039. //#define FIL_RUNOUT2_PULLDOWN
  1040. //#define FIL_RUNOUT3_STATE LOW
  1041. //#define FIL_RUNOUT3_PULLUP
  1042. //#define FIL_RUNOUT3_PULLDOWN
  1043. //#define FIL_RUNOUT4_STATE LOW
  1044. //#define FIL_RUNOUT4_PULLUP
  1045. //#define FIL_RUNOUT4_PULLDOWN
  1046. //#define FIL_RUNOUT5_STATE LOW
  1047. //#define FIL_RUNOUT5_PULLUP
  1048. //#define FIL_RUNOUT5_PULLDOWN
  1049. //#define FIL_RUNOUT6_STATE LOW
  1050. //#define FIL_RUNOUT6_PULLUP
  1051. //#define FIL_RUNOUT6_PULLDOWN
  1052. //#define FIL_RUNOUT7_STATE LOW
  1053. //#define FIL_RUNOUT7_PULLUP
  1054. //#define FIL_RUNOUT7_PULLDOWN
  1055. //#define FIL_RUNOUT8_STATE LOW
  1056. //#define FIL_RUNOUT8_PULLUP
  1057. //#define FIL_RUNOUT8_PULLDOWN
  1058. // Set one or more commands to execute on filament runout.
  1059. // (After 'M412 H' Marlin will ask the host to handle the process.)
  1060. #define FILAMENT_RUNOUT_SCRIPT "M600"
  1061. // After a runout is detected, continue printing this length of filament
  1062. // before executing the runout script. Useful for a sensor at the end of
  1063. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  1064. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  1065. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  1066. // Enable this option to use an encoder disc that toggles the runout pin
  1067. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  1068. // large enough to avoid false positives.)
  1069. //#define FILAMENT_MOTION_SENSOR
  1070. #endif
  1071. #endif
  1072. //===========================================================================
  1073. //=============================== Bed Leveling ==============================
  1074. //===========================================================================
  1075. // @section calibrate
  1076. /**
  1077. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  1078. * and behavior of G29 will change depending on your selection.
  1079. *
  1080. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  1081. *
  1082. * - AUTO_BED_LEVELING_3POINT
  1083. * Probe 3 arbitrary points on the bed (that aren't collinear)
  1084. * You specify the XY coordinates of all 3 points.
  1085. * The result is a single tilted plane. Best for a flat bed.
  1086. *
  1087. * - AUTO_BED_LEVELING_LINEAR
  1088. * Probe several points in a grid.
  1089. * You specify the rectangle and the density of sample points.
  1090. * The result is a single tilted plane. Best for a flat bed.
  1091. *
  1092. * - AUTO_BED_LEVELING_BILINEAR
  1093. * Probe several points in a grid.
  1094. * You specify the rectangle and the density of sample points.
  1095. * The result is a mesh, best for large or uneven beds.
  1096. *
  1097. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1098. * A comprehensive bed leveling system combining the features and benefits
  1099. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1100. * Validation and Mesh Editing systems.
  1101. *
  1102. * - MESH_BED_LEVELING
  1103. * Probe a grid manually
  1104. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1105. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1106. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1107. * With an LCD controller the process is guided step-by-step.
  1108. */
  1109. //#define AUTO_BED_LEVELING_3POINT
  1110. //#define AUTO_BED_LEVELING_LINEAR
  1111. //#define AUTO_BED_LEVELING_BILINEAR
  1112. //#define AUTO_BED_LEVELING_UBL
  1113. //#define MESH_BED_LEVELING
  1114. /**
  1115. * Normally G28 leaves leveling disabled on completion. Enable one of
  1116. * these options to restore the prior leveling state or to always enable
  1117. * leveling immediately after G28.
  1118. */
  1119. //#define RESTORE_LEVELING_AFTER_G28
  1120. //#define ENABLE_LEVELING_AFTER_G28
  1121. /**
  1122. * Auto-leveling needs preheating
  1123. */
  1124. //#define PREHEAT_BEFORE_LEVELING
  1125. #if ENABLED(PREHEAT_BEFORE_LEVELING)
  1126. #define LEVELING_NOZZLE_TEMP 120
  1127. #define LEVELING_BED_TEMP 50
  1128. #endif
  1129. /**
  1130. * Enable detailed logging of G28, G29, M48, etc.
  1131. * Turn on with the command 'M111 S32'.
  1132. * NOTE: Requires a lot of PROGMEM!
  1133. */
  1134. //#define DEBUG_LEVELING_FEATURE
  1135. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1136. // Gradually reduce leveling correction until a set height is reached,
  1137. // at which point movement will be level to the machine's XY plane.
  1138. // The height can be set with M420 Z<height>
  1139. #define ENABLE_LEVELING_FADE_HEIGHT
  1140. #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
  1141. #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
  1142. #endif
  1143. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1144. // split up moves into short segments like a Delta. This follows the
  1145. // contours of the bed more closely than edge-to-edge straight moves.
  1146. #define SEGMENT_LEVELED_MOVES
  1147. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1148. /**
  1149. * Enable the G26 Mesh Validation Pattern tool.
  1150. */
  1151. //#define G26_MESH_VALIDATION
  1152. #if ENABLED(G26_MESH_VALIDATION)
  1153. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1154. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1155. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1156. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1157. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1158. #define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
  1159. #endif
  1160. #endif
  1161. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1162. // Set the number of grid points per dimension.
  1163. #define GRID_MAX_POINTS_X 3
  1164. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1165. // Probe along the Y axis, advancing X after each column
  1166. //#define PROBE_Y_FIRST
  1167. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1168. // Beyond the probed grid, continue the implied tilt?
  1169. // Default is to maintain the height of the nearest edge.
  1170. //#define EXTRAPOLATE_BEYOND_GRID
  1171. //
  1172. // Experimental Subdivision of the grid by Catmull-Rom method.
  1173. // Synthesizes intermediate points to produce a more detailed mesh.
  1174. //
  1175. //#define ABL_BILINEAR_SUBDIVISION
  1176. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1177. // Number of subdivisions between probe points
  1178. #define BILINEAR_SUBDIVISIONS 3
  1179. #endif
  1180. #endif
  1181. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1182. //===========================================================================
  1183. //========================= Unified Bed Leveling ============================
  1184. //===========================================================================
  1185. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1186. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1187. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1188. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1189. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1190. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1191. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1192. // as the Z-Height correction value.
  1193. #elif ENABLED(MESH_BED_LEVELING)
  1194. //===========================================================================
  1195. //=================================== Mesh ==================================
  1196. //===========================================================================
  1197. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1198. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1199. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1200. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1201. #endif // BED_LEVELING
  1202. /**
  1203. * Add a bed leveling sub-menu for ABL or MBL.
  1204. * Include a guided procedure if manual probing is enabled.
  1205. */
  1206. //#define LCD_BED_LEVELING
  1207. #if ENABLED(LCD_BED_LEVELING)
  1208. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1209. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1210. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1211. #endif
  1212. // Add a menu item to move between bed corners for manual bed adjustment
  1213. //#define LEVEL_BED_CORNERS
  1214. #if ENABLED(LEVEL_BED_CORNERS)
  1215. #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
  1216. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1217. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
  1218. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1219. //#define LEVEL_CORNERS_USE_PROBE
  1220. #if ENABLED(LEVEL_CORNERS_USE_PROBE)
  1221. #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
  1222. #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
  1223. //#define LEVEL_CORNERS_AUDIO_FEEDBACK
  1224. #endif
  1225. #endif
  1226. /**
  1227. * Commands to execute at the end of G29 probing.
  1228. * Useful to retract or move the Z probe out of the way.
  1229. */
  1230. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1231. // @section homing
  1232. // The center of the bed is at (X=0, Y=0)
  1233. //#define BED_CENTER_AT_0_0
  1234. // Manually set the home position. Leave these undefined for automatic settings.
  1235. // For DELTA this is the top-center of the Cartesian print volume.
  1236. //#define MANUAL_X_HOME_POS 0
  1237. //#define MANUAL_Y_HOME_POS 0
  1238. //#define MANUAL_Z_HOME_POS 0
  1239. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1240. //
  1241. // With this feature enabled:
  1242. //
  1243. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1244. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1245. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
  1246. // - Prevent Z homing when the Z probe is outside bed area.
  1247. //
  1248. //#define Z_SAFE_HOMING
  1249. #if ENABLED(Z_SAFE_HOMING)
  1250. #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
  1251. #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
  1252. #endif
  1253. // Homing speeds (mm/min)
  1254. #define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
  1255. // Validate that endstops are triggered on homing moves
  1256. #define VALIDATE_HOMING_ENDSTOPS
  1257. // @section calibrate
  1258. /**
  1259. * Bed Skew Compensation
  1260. *
  1261. * This feature corrects for misalignment in the XYZ axes.
  1262. *
  1263. * Take the following steps to get the bed skew in the XY plane:
  1264. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1265. * 2. For XY_DIAG_AC measure the diagonal A to C
  1266. * 3. For XY_DIAG_BD measure the diagonal B to D
  1267. * 4. For XY_SIDE_AD measure the edge A to D
  1268. *
  1269. * Marlin automatically computes skew factors from these measurements.
  1270. * Skew factors may also be computed and set manually:
  1271. *
  1272. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1273. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1274. *
  1275. * If desired, follow the same procedure for XZ and YZ.
  1276. * Use these diagrams for reference:
  1277. *
  1278. * Y Z Z
  1279. * ^ B-------C ^ B-------C ^ B-------C
  1280. * | / / | / / | / /
  1281. * | / / | / / | / /
  1282. * | A-------D | A-------D | A-------D
  1283. * +-------------->X +-------------->X +-------------->Y
  1284. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1285. */
  1286. //#define SKEW_CORRECTION
  1287. #if ENABLED(SKEW_CORRECTION)
  1288. // Input all length measurements here:
  1289. #define XY_DIAG_AC 282.8427124746
  1290. #define XY_DIAG_BD 282.8427124746
  1291. #define XY_SIDE_AD 200
  1292. // Or, set the default skew factors directly here
  1293. // to override the above measurements:
  1294. #define XY_SKEW_FACTOR 0.0
  1295. //#define SKEW_CORRECTION_FOR_Z
  1296. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1297. #define XZ_DIAG_AC 282.8427124746
  1298. #define XZ_DIAG_BD 282.8427124746
  1299. #define YZ_DIAG_AC 282.8427124746
  1300. #define YZ_DIAG_BD 282.8427124746
  1301. #define YZ_SIDE_AD 200
  1302. #define XZ_SKEW_FACTOR 0.0
  1303. #define YZ_SKEW_FACTOR 0.0
  1304. #endif
  1305. // Enable this option for M852 to set skew at runtime
  1306. //#define SKEW_CORRECTION_GCODE
  1307. #endif
  1308. //=============================================================================
  1309. //============================= Additional Features ===========================
  1310. //=============================================================================
  1311. // @section extras
  1312. /**
  1313. * EEPROM
  1314. *
  1315. * Persistent storage to preserve configurable settings across reboots.
  1316. *
  1317. * M500 - Store settings to EEPROM.
  1318. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1319. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1320. */
  1321. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1322. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1323. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1324. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
  1325. #if ENABLED(EEPROM_SETTINGS)
  1326. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1327. #endif
  1328. //
  1329. // Host Keepalive
  1330. //
  1331. // When enabled Marlin will send a busy status message to the host
  1332. // every couple of seconds when it can't accept commands.
  1333. //
  1334. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1335. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1336. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1337. //
  1338. // G20/G21 Inch mode support
  1339. //
  1340. //#define INCH_MODE_SUPPORT
  1341. //
  1342. // M149 Set temperature units support
  1343. //
  1344. //#define TEMPERATURE_UNITS_SUPPORT
  1345. // @section temperature
  1346. // Preheat Constants
  1347. #define PREHEAT_1_LABEL "PLA"
  1348. #define PREHEAT_1_TEMP_HOTEND 180
  1349. #define PREHEAT_1_TEMP_BED 70
  1350. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1351. #define PREHEAT_2_LABEL "ABS"
  1352. #define PREHEAT_2_TEMP_HOTEND 240
  1353. #define PREHEAT_2_TEMP_BED 110
  1354. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1355. /**
  1356. * Nozzle Park
  1357. *
  1358. * Park the nozzle at the given XYZ position on idle or G27.
  1359. *
  1360. * The "P" parameter controls the action applied to the Z axis:
  1361. *
  1362. * P0 (Default) If Z is below park Z raise the nozzle.
  1363. * P1 Raise the nozzle always to Z-park height.
  1364. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1365. */
  1366. //#define NOZZLE_PARK_FEATURE
  1367. #if ENABLED(NOZZLE_PARK_FEATURE)
  1368. // Specify a park position as { X, Y, Z_raise }
  1369. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1370. //#define NOZZLE_PARK_X_ONLY // X move only is required to park
  1371. //#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
  1372. #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
  1373. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1374. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1375. #endif
  1376. /**
  1377. * Clean Nozzle Feature -- EXPERIMENTAL
  1378. *
  1379. * Adds the G12 command to perform a nozzle cleaning process.
  1380. *
  1381. * Parameters:
  1382. * P Pattern
  1383. * S Strokes / Repetitions
  1384. * T Triangles (P1 only)
  1385. *
  1386. * Patterns:
  1387. * P0 Straight line (default). This process requires a sponge type material
  1388. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1389. * between the start / end points.
  1390. *
  1391. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1392. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1393. * Zig-zags are done in whichever is the narrower dimension.
  1394. * For example, "G12 P1 S1 T3" will execute:
  1395. *
  1396. * --
  1397. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1398. * | | / \ / \ / \ |
  1399. * A | | / \ / \ / \ |
  1400. * | | / \ / \ / \ |
  1401. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1402. * -- +--------------------------------+
  1403. * |________|_________|_________|
  1404. * T1 T2 T3
  1405. *
  1406. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1407. * "R" specifies the radius. "S" specifies the stroke count.
  1408. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1409. *
  1410. * Caveats: The ending Z should be the same as starting Z.
  1411. * Attention: EXPERIMENTAL. G-code arguments may change.
  1412. */
  1413. //#define NOZZLE_CLEAN_FEATURE
  1414. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1415. // Default number of pattern repetitions
  1416. #define NOZZLE_CLEAN_STROKES 12
  1417. // Default number of triangles
  1418. #define NOZZLE_CLEAN_TRIANGLES 3
  1419. // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
  1420. // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
  1421. #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } }
  1422. #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }
  1423. // Circular pattern radius
  1424. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1425. // Circular pattern circle fragments number
  1426. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1427. // Middle point of circle
  1428. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1429. // Move the nozzle to the initial position after cleaning
  1430. #define NOZZLE_CLEAN_GOBACK
  1431. // For a purge/clean station that's always at the gantry height (thus no Z move)
  1432. //#define NOZZLE_CLEAN_NO_Z
  1433. // For a purge/clean station mounted on the X axis
  1434. //#define NOZZLE_CLEAN_NO_Y
  1435. // Explicit wipe G-code script applies to a G12 with no arguments.
  1436. //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0"
  1437. #endif
  1438. /**
  1439. * Print Job Timer
  1440. *
  1441. * Automatically start and stop the print job timer on M104/M109/M190.
  1442. *
  1443. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1444. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1445. * M190 (bed, wait) - high temp = start timer, low temp = none
  1446. *
  1447. * The timer can also be controlled with the following commands:
  1448. *
  1449. * M75 - Start the print job timer
  1450. * M76 - Pause the print job timer
  1451. * M77 - Stop the print job timer
  1452. */
  1453. #define PRINTJOB_TIMER_AUTOSTART
  1454. /**
  1455. * Print Counter
  1456. *
  1457. * Track statistical data such as:
  1458. *
  1459. * - Total print jobs
  1460. * - Total successful print jobs
  1461. * - Total failed print jobs
  1462. * - Total time printing
  1463. *
  1464. * View the current statistics with M78.
  1465. */
  1466. //#define PRINTCOUNTER
  1467. /**
  1468. * Password
  1469. *
  1470. * Set a numerical password for the printer which can be requested:
  1471. *
  1472. * - When the printer boots up
  1473. * - Upon opening the 'Print from Media' Menu
  1474. * - When SD printing is completed or aborted
  1475. *
  1476. * The following G-codes can be used:
  1477. *
  1478. * M510 - Lock Printer. Blocks all commands except M511.
  1479. * M511 - Unlock Printer.
  1480. * M512 - Set, Change and Remove Password.
  1481. *
  1482. * If you forget the password and get locked out you'll need to re-flash
  1483. * the firmware with the feature disabled, reset EEPROM, and (optionally)
  1484. * re-flash the firmware again with this feature enabled.
  1485. */
  1486. //#define PASSWORD_FEATURE
  1487. #if ENABLED(PASSWORD_FEATURE)
  1488. #define PASSWORD_LENGTH 4 // (#) Number of digits (1-9). 3 or 4 is recommended
  1489. #define PASSWORD_ON_STARTUP
  1490. #define PASSWORD_UNLOCK_GCODE // Unlock with the M511 P<password> command. Disable to prevent brute-force attack.
  1491. #define PASSWORD_CHANGE_GCODE // Change the password with M512 P<old> S<new>.
  1492. //#define PASSWORD_ON_SD_PRINT_MENU // This does not prevent gcodes from running
  1493. //#define PASSWORD_AFTER_SD_PRINT_END
  1494. //#define PASSWORD_AFTER_SD_PRINT_ABORT
  1495. //#include "Configuration_Secure.h" // External file with PASSWORD_DEFAULT_VALUE
  1496. #endif
  1497. //=============================================================================
  1498. //============================= LCD and SD support ============================
  1499. //=============================================================================
  1500. // @section lcd
  1501. /**
  1502. * LCD LANGUAGE
  1503. *
  1504. * Select the language to display on the LCD. These languages are available:
  1505. *
  1506. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, hu, it,
  1507. * jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1508. *
  1509. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1510. */
  1511. #define LCD_LANGUAGE en
  1512. /**
  1513. * LCD Character Set
  1514. *
  1515. * Note: This option is NOT applicable to Graphical Displays.
  1516. *
  1517. * All character-based LCDs provide ASCII plus one of these
  1518. * language extensions:
  1519. *
  1520. * - JAPANESE ... the most common
  1521. * - WESTERN ... with more accented characters
  1522. * - CYRILLIC ... for the Russian language
  1523. *
  1524. * To determine the language extension installed on your controller:
  1525. *
  1526. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1527. * - Click the controller to view the LCD menu
  1528. * - The LCD will display Japanese, Western, or Cyrillic text
  1529. *
  1530. * See https://marlinfw.org/docs/development/lcd_language.html
  1531. *
  1532. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1533. */
  1534. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1535. /**
  1536. * Info Screen Style (0:Classic, 1:Průša)
  1537. *
  1538. * :[0:'Classic', 1:'Průša']
  1539. */
  1540. #define LCD_INFO_SCREEN_STYLE 0
  1541. /**
  1542. * SD CARD
  1543. *
  1544. * SD Card support is disabled by default. If your controller has an SD slot,
  1545. * you must uncomment the following option or it won't work.
  1546. */
  1547. //#define SDSUPPORT
  1548. /**
  1549. * SD CARD: SPI SPEED
  1550. *
  1551. * Enable one of the following items for a slower SPI transfer speed.
  1552. * This may be required to resolve "volume init" errors.
  1553. */
  1554. //#define SPI_SPEED SPI_HALF_SPEED
  1555. //#define SPI_SPEED SPI_QUARTER_SPEED
  1556. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1557. /**
  1558. * SD CARD: ENABLE CRC
  1559. *
  1560. * Use CRC checks and retries on the SD communication.
  1561. */
  1562. //#define SD_CHECK_AND_RETRY
  1563. /**
  1564. * LCD Menu Items
  1565. *
  1566. * Disable all menus and only display the Status Screen, or
  1567. * just remove some extraneous menu items to recover space.
  1568. */
  1569. //#define NO_LCD_MENUS
  1570. //#define SLIM_LCD_MENUS
  1571. //
  1572. // ENCODER SETTINGS
  1573. //
  1574. // This option overrides the default number of encoder pulses needed to
  1575. // produce one step. Should be increased for high-resolution encoders.
  1576. //
  1577. //#define ENCODER_PULSES_PER_STEP 4
  1578. //
  1579. // Use this option to override the number of step signals required to
  1580. // move between next/prev menu items.
  1581. //
  1582. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1583. /**
  1584. * Encoder Direction Options
  1585. *
  1586. * Test your encoder's behavior first with both options disabled.
  1587. *
  1588. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1589. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1590. * Reversed Value Editing only? Enable BOTH options.
  1591. */
  1592. //
  1593. // This option reverses the encoder direction everywhere.
  1594. //
  1595. // Set this option if CLOCKWISE causes values to DECREASE
  1596. //
  1597. //#define REVERSE_ENCODER_DIRECTION
  1598. //
  1599. // This option reverses the encoder direction for navigating LCD menus.
  1600. //
  1601. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1602. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1603. //
  1604. //#define REVERSE_MENU_DIRECTION
  1605. //
  1606. // This option reverses the encoder direction for Select Screen.
  1607. //
  1608. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1609. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1610. //
  1611. //#define REVERSE_SELECT_DIRECTION
  1612. //
  1613. // Individual Axis Homing
  1614. //
  1615. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1616. //
  1617. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1618. //
  1619. // SPEAKER/BUZZER
  1620. //
  1621. // If you have a speaker that can produce tones, enable it here.
  1622. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1623. //
  1624. //#define SPEAKER
  1625. //
  1626. // The duration and frequency for the UI feedback sound.
  1627. // Set these to 0 to disable audio feedback in the LCD menus.
  1628. //
  1629. // Note: Test audio output with the G-Code:
  1630. // M300 S<frequency Hz> P<duration ms>
  1631. //
  1632. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1633. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1634. //=============================================================================
  1635. //======================== LCD / Controller Selection =========================
  1636. //======================== (Character-based LCDs) =========================
  1637. //=============================================================================
  1638. //
  1639. // RepRapDiscount Smart Controller.
  1640. // https://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1641. //
  1642. // Note: Usually sold with a white PCB.
  1643. //
  1644. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1645. //
  1646. // Original RADDS LCD Display+Encoder+SDCardReader
  1647. // http://doku.radds.org/dokumentation/lcd-display/
  1648. //
  1649. //#define RADDS_DISPLAY
  1650. //
  1651. // ULTIMAKER Controller.
  1652. //
  1653. //#define ULTIMAKERCONTROLLER
  1654. //
  1655. // ULTIPANEL as seen on Thingiverse.
  1656. //
  1657. //#define ULTIPANEL
  1658. //
  1659. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1660. // https://reprap.org/wiki/PanelOne
  1661. //
  1662. //#define PANEL_ONE
  1663. //
  1664. // GADGETS3D G3D LCD/SD Controller
  1665. // https://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1666. //
  1667. // Note: Usually sold with a blue PCB.
  1668. //
  1669. //#define G3D_PANEL
  1670. //
  1671. // RigidBot Panel V1.0
  1672. // http://www.inventapart.com/
  1673. //
  1674. //#define RIGIDBOT_PANEL
  1675. //
  1676. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1677. // https://www.aliexpress.com/item/32765887917.html
  1678. //
  1679. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1680. //
  1681. // ANET and Tronxy 20x4 Controller
  1682. //
  1683. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1684. // This LCD is known to be susceptible to electrical interference
  1685. // which scrambles the display. Pressing any button clears it up.
  1686. // This is a LCD2004 display with 5 analog buttons.
  1687. //
  1688. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1689. //
  1690. //#define ULTRA_LCD
  1691. //=============================================================================
  1692. //======================== LCD / Controller Selection =========================
  1693. //===================== (I2C and Shift-Register LCDs) =====================
  1694. //=============================================================================
  1695. //
  1696. // CONTROLLER TYPE: I2C
  1697. //
  1698. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1699. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1700. //
  1701. //
  1702. // Elefu RA Board Control Panel
  1703. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1704. //
  1705. //#define RA_CONTROL_PANEL
  1706. //
  1707. // Sainsmart (YwRobot) LCD Displays
  1708. //
  1709. // These require F.Malpartida's LiquidCrystal_I2C library
  1710. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1711. //
  1712. //#define LCD_SAINSMART_I2C_1602
  1713. //#define LCD_SAINSMART_I2C_2004
  1714. //
  1715. // Generic LCM1602 LCD adapter
  1716. //
  1717. //#define LCM1602
  1718. //
  1719. // PANELOLU2 LCD with status LEDs,
  1720. // separate encoder and click inputs.
  1721. //
  1722. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1723. // For more info: https://github.com/lincomatic/LiquidTWI2
  1724. //
  1725. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1726. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1727. //
  1728. //#define LCD_I2C_PANELOLU2
  1729. //
  1730. // Panucatt VIKI LCD with status LEDs,
  1731. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1732. //
  1733. //#define LCD_I2C_VIKI
  1734. //
  1735. // CONTROLLER TYPE: Shift register panels
  1736. //
  1737. //
  1738. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1739. // LCD configuration: https://reprap.org/wiki/SAV_3D_LCD
  1740. //
  1741. //#define SAV_3DLCD
  1742. //
  1743. // 3-wire SR LCD with strobe using 74HC4094
  1744. // https://github.com/mikeshub/SailfishLCD
  1745. // Uses the code directly from Sailfish
  1746. //
  1747. //#define FF_INTERFACEBOARD
  1748. //
  1749. // TFT GLCD Panel with Marlin UI
  1750. // Panel connected to main board by SPI or I2C interface.
  1751. // See https://github.com/Serhiy-K/TFTGLCDAdapter
  1752. //
  1753. //#define TFTGLCD_PANEL_SPI
  1754. //#define TFTGLCD_PANEL_I2C
  1755. //=============================================================================
  1756. //======================= LCD / Controller Selection =======================
  1757. //========================= (Graphical LCDs) ========================
  1758. //=============================================================================
  1759. //
  1760. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1761. //
  1762. // IMPORTANT: The U8glib library is required for Graphical Display!
  1763. // https://github.com/olikraus/U8glib_Arduino
  1764. //
  1765. // NOTE: If the LCD is unresponsive you may need to reverse the plugs.
  1766. //
  1767. //
  1768. // RepRapDiscount FULL GRAPHIC Smart Controller
  1769. // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1770. //
  1771. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1772. //
  1773. // ReprapWorld Graphical LCD
  1774. // https://reprapworld.com/?products_details&products_id/1218
  1775. //
  1776. //#define REPRAPWORLD_GRAPHICAL_LCD
  1777. //
  1778. // Activate one of these if you have a Panucatt Devices
  1779. // Viki 2.0 or mini Viki with Graphic LCD
  1780. // https://www.panucatt.com
  1781. //
  1782. //#define VIKI2
  1783. //#define miniVIKI
  1784. //
  1785. // MakerLab Mini Panel with graphic
  1786. // controller and SD support - https://reprap.org/wiki/Mini_panel
  1787. //
  1788. //#define MINIPANEL
  1789. //
  1790. // MaKr3d Makr-Panel with graphic controller and SD support.
  1791. // https://reprap.org/wiki/MaKr3d_MaKrPanel
  1792. //
  1793. //#define MAKRPANEL
  1794. //
  1795. // Adafruit ST7565 Full Graphic Controller.
  1796. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1797. //
  1798. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1799. //
  1800. // BQ LCD Smart Controller shipped by
  1801. // default with the BQ Hephestos 2 and Witbox 2.
  1802. //
  1803. //#define BQ_LCD_SMART_CONTROLLER
  1804. //
  1805. // Cartesio UI
  1806. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1807. //
  1808. //#define CARTESIO_UI
  1809. //
  1810. // LCD for Melzi Card with Graphical LCD
  1811. //
  1812. //#define LCD_FOR_MELZI
  1813. //
  1814. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1815. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1816. //
  1817. //#define ULTI_CONTROLLER
  1818. //
  1819. // MKS MINI12864 with graphic controller and SD support
  1820. // https://reprap.org/wiki/MKS_MINI_12864
  1821. //
  1822. //#define MKS_MINI_12864
  1823. //
  1824. // MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout.
  1825. // https://www.aliexpress.com/item/33018110072.html
  1826. //
  1827. //#define MKS_LCD12864
  1828. //
  1829. // FYSETC variant of the MINI12864 graphic controller with SD support
  1830. // https://wiki.fysetc.com/Mini12864_Panel/
  1831. //
  1832. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1833. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1834. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1835. //#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight
  1836. //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight.
  1837. //
  1838. // Factory display for Creality CR-10
  1839. // https://www.aliexpress.com/item/32833148327.html
  1840. //
  1841. // This is RAMPS-compatible using a single 10-pin connector.
  1842. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1843. //
  1844. //#define CR10_STOCKDISPLAY
  1845. //
  1846. // Ender-2 OEM display, a variant of the MKS_MINI_12864
  1847. //
  1848. //#define ENDER2_STOCKDISPLAY
  1849. //
  1850. // ANET and Tronxy Graphical Controller
  1851. //
  1852. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1853. // A clone of the RepRapDiscount full graphics display but with
  1854. // different pins/wiring (see pins_ANET_10.h). Enable one of these.
  1855. //
  1856. //#define ANET_FULL_GRAPHICS_LCD
  1857. //#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING
  1858. //
  1859. // AZSMZ 12864 LCD with SD
  1860. // https://www.aliexpress.com/item/32837222770.html
  1861. //
  1862. //#define AZSMZ_12864
  1863. //
  1864. // Silvergate GLCD controller
  1865. // https://github.com/android444/Silvergate
  1866. //
  1867. //#define SILVER_GATE_GLCD_CONTROLLER
  1868. //=============================================================================
  1869. //============================== OLED Displays ==============================
  1870. //=============================================================================
  1871. //
  1872. // SSD1306 OLED full graphics generic display
  1873. //
  1874. //#define U8GLIB_SSD1306
  1875. //
  1876. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1877. //
  1878. //#define SAV_3DGLCD
  1879. #if ENABLED(SAV_3DGLCD)
  1880. #define U8GLIB_SSD1306
  1881. //#define U8GLIB_SH1106
  1882. #endif
  1883. //
  1884. // TinyBoy2 128x64 OLED / Encoder Panel
  1885. //
  1886. //#define OLED_PANEL_TINYBOY2
  1887. //
  1888. // MKS OLED 1.3" 128×64 FULL GRAPHICS CONTROLLER
  1889. // https://reprap.org/wiki/MKS_12864OLED
  1890. //
  1891. // Tiny, but very sharp OLED display
  1892. //
  1893. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1894. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1895. //
  1896. // Zonestar OLED 128×64 FULL GRAPHICS CONTROLLER
  1897. //
  1898. //#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller
  1899. //#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default)
  1900. //#define ZONESTAR_12864OLED_SSD1306 // 0.96" OLED with SSD1306 controller
  1901. //
  1902. // Einstart S OLED SSD1306
  1903. //
  1904. //#define U8GLIB_SH1106_EINSTART
  1905. //
  1906. // Overlord OLED display/controller with i2c buzzer and LEDs
  1907. //
  1908. //#define OVERLORD_OLED
  1909. //
  1910. // FYSETC OLED 2.42" 128×64 FULL GRAPHICS CONTROLLER with WS2812 RGB
  1911. // Where to find : https://www.aliexpress.com/item/4000345255731.html
  1912. //#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller
  1913. //=============================================================================
  1914. //========================== Extensible UI Displays ===========================
  1915. //=============================================================================
  1916. //
  1917. // DGUS Touch Display with DWIN OS. (Choose one.)
  1918. // ORIGIN : https://www.aliexpress.com/item/32993409517.html
  1919. // FYSETC : https://www.aliexpress.com/item/32961471929.html
  1920. //
  1921. //#define DGUS_LCD_UI_ORIGIN
  1922. //#define DGUS_LCD_UI_FYSETC
  1923. //#define DGUS_LCD_UI_HIPRECY
  1924. //
  1925. // Touch-screen LCD for Malyan M200/M300 printers
  1926. //
  1927. //#define MALYAN_LCD
  1928. #if ENABLED(MALYAN_LCD)
  1929. #define LCD_SERIAL_PORT 1 // Default is 1 for Malyan M200
  1930. #endif
  1931. //
  1932. // Touch UI for FTDI EVE (FT800/FT810) displays
  1933. // See Configuration_adv.h for all configuration options.
  1934. //
  1935. //#define TOUCH_UI_FTDI_EVE
  1936. //
  1937. // Touch-screen LCD for Anycubic printers
  1938. //
  1939. //#define ANYCUBIC_LCD_I3MEGA
  1940. //#define ANYCUBIC_LCD_CHIRON
  1941. #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
  1942. #define LCD_SERIAL_PORT 3 // Default is 3 for Anycubic
  1943. //#define ANYCUBIC_LCD_DEBUG
  1944. #endif
  1945. //
  1946. // Third-party or vendor-customized controller interfaces.
  1947. // Sources should be installed in 'src/lcd/extui'.
  1948. //
  1949. //#define EXTENSIBLE_UI
  1950. #if ENABLED(EXTENSIBLE_UI)
  1951. //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display
  1952. #endif
  1953. //=============================================================================
  1954. //=============================== Graphical TFTs ==============================
  1955. //=============================================================================
  1956. /**
  1957. * Specific TFT Model Presets. Enable one of the following options
  1958. * or enable TFT_GENERIC and set sub-options.
  1959. */
  1960. //
  1961. // 480x320, 3.5", SPI Display From MKS
  1962. // Normally used in MKS Robin Nano V2
  1963. //
  1964. //#define MKS_TS35_V2_0
  1965. //
  1966. // 320x240, 2.4", FSMC Display From MKS
  1967. // Normally used in MKS Robin Nano V1.2
  1968. //
  1969. //#define MKS_ROBIN_TFT24
  1970. //
  1971. // 320x240, 2.8", FSMC Display From MKS
  1972. // Normally used in MKS Robin Nano V1.2
  1973. //
  1974. //#define MKS_ROBIN_TFT28
  1975. //
  1976. // 320x240, 3.2", FSMC Display From MKS
  1977. // Normally used in MKS Robin Nano V1.2
  1978. //
  1979. //#define MKS_ROBIN_TFT32
  1980. //
  1981. // 480x320, 3.5", FSMC Display From MKS
  1982. // Normally used in MKS Robin Nano V1.2
  1983. //
  1984. //#define MKS_ROBIN_TFT35
  1985. //
  1986. // 480x272, 4.3", FSMC Display From MKS
  1987. //
  1988. //#define MKS_ROBIN_TFT43
  1989. //
  1990. // 320x240, 3.2", FSMC Display From MKS
  1991. // Normally used in MKS Robin
  1992. //
  1993. //#define MKS_ROBIN_TFT_V1_1R
  1994. //
  1995. // 480x320, 3.5", FSMC Stock Display from TronxXY
  1996. //
  1997. //#define TFT_TRONXY_X5SA
  1998. //
  1999. // 480x320, 3.5", FSMC Stock Display from AnyCubic
  2000. //
  2001. //#define ANYCUBIC_TFT35
  2002. //
  2003. // 320x240, 2.8", FSMC Stock Display from Longer/Alfawise
  2004. //
  2005. //#define LONGER_LK_TFT28
  2006. //
  2007. // Generic TFT with detailed options
  2008. //
  2009. //#define TFT_GENERIC
  2010. #if ENABLED(TFT_GENERIC)
  2011. // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
  2012. #define TFT_DRIVER AUTO
  2013. // Interface. Enable one of the following options:
  2014. //#define TFT_INTERFACE_FSMC
  2015. //#define TFT_INTERFACE_SPI
  2016. // TFT Resolution. Enable one of the following options:
  2017. //#define TFT_RES_320x240
  2018. //#define TFT_RES_480x272
  2019. //#define TFT_RES_480x320
  2020. #endif
  2021. /**
  2022. * TFT UI - User Interface Selection. Enable one of the following options:
  2023. *
  2024. * TFT_CLASSIC_UI - Emulated DOGM - 128x64 Upscaled
  2025. * TFT_COLOR_UI - Marlin Default Menus, Touch Friendly, using full TFT capabilities
  2026. * TFT_LVGL_UI - A Modern UI using LVGL
  2027. *
  2028. * For LVGL_UI also copy the 'assets' folder from the build directory to the
  2029. * root of your SD card, together with the compiled firmware.
  2030. */
  2031. //#define TFT_CLASSIC_UI
  2032. //#define TFT_COLOR_UI
  2033. //#define TFT_LVGL_UI
  2034. /**
  2035. * TFT Rotation. Set to one of the following values:
  2036. *
  2037. * TFT_ROTATE_90, TFT_ROTATE_90_MIRROR_X, TFT_ROTATE_90_MIRROR_Y,
  2038. * TFT_ROTATE_180, TFT_ROTATE_180_MIRROR_X, TFT_ROTATE_180_MIRROR_Y,
  2039. * TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y,
  2040. * TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION
  2041. */
  2042. //#define TFT_ROTATION TFT_NO_ROTATION
  2043. //=============================================================================
  2044. //============================ Other Controllers ============================
  2045. //=============================================================================
  2046. //
  2047. // Ender-3 v2 OEM display. A DWIN display with Rotary Encoder.
  2048. //
  2049. //#define DWIN_CREALITY_LCD
  2050. //
  2051. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  2052. //
  2053. //#define TOUCH_SCREEN
  2054. #if ENABLED(TOUCH_SCREEN)
  2055. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  2056. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  2057. #define TOUCH_SCREEN_CALIBRATION
  2058. //#define TOUCH_CALIBRATION_X 12316
  2059. //#define TOUCH_CALIBRATION_Y -8981
  2060. //#define TOUCH_OFFSET_X -43
  2061. //#define TOUCH_OFFSET_Y 257
  2062. #if ENABLED(TFT_COLOR_UI)
  2063. //#define SINGLE_TOUCH_NAVIGATION
  2064. #endif
  2065. #endif
  2066. //
  2067. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  2068. // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
  2069. //
  2070. //#define REPRAPWORLD_KEYPAD
  2071. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  2072. //=============================================================================
  2073. //=============================== Extra Features ==============================
  2074. //=============================================================================
  2075. // @section extras
  2076. // Set number of user-controlled fans. Disable to use all board-defined fans.
  2077. // :[1,2,3,4,5,6,7,8]
  2078. //#define NUM_M106_FANS 1
  2079. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  2080. //#define FAST_PWM_FAN
  2081. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  2082. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  2083. // is too low, you should also increment SOFT_PWM_SCALE.
  2084. //#define FAN_SOFT_PWM
  2085. // Incrementing this by 1 will double the software PWM frequency,
  2086. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  2087. // However, control resolution will be halved for each increment;
  2088. // at zero value, there are 128 effective control positions.
  2089. // :[0,1,2,3,4,5,6,7]
  2090. #define SOFT_PWM_SCALE 0
  2091. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  2092. // be used to mitigate the associated resolution loss. If enabled,
  2093. // some of the PWM cycles are stretched so on average the desired
  2094. // duty cycle is attained.
  2095. //#define SOFT_PWM_DITHER
  2096. // Temperature status LEDs that display the hotend and bed temperature.
  2097. // If all hotends, bed temperature, and target temperature are under 54C
  2098. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  2099. //#define TEMP_STAT_LEDS
  2100. // Support for the BariCUDA Paste Extruder
  2101. //#define BARICUDA
  2102. // Support for BlinkM/CyzRgb
  2103. //#define BLINKM
  2104. // Support for PCA9632 PWM LED driver
  2105. //#define PCA9632
  2106. // Support for PCA9533 PWM LED driver
  2107. //#define PCA9533
  2108. /**
  2109. * RGB LED / LED Strip Control
  2110. *
  2111. * Enable support for an RGB LED connected to 5V digital pins, or
  2112. * an RGB Strip connected to MOSFETs controlled by digital pins.
  2113. *
  2114. * Adds the M150 command to set the LED (or LED strip) color.
  2115. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  2116. * luminance values can be set from 0 to 255.
  2117. * For NeoPixel LED an overall brightness parameter is also available.
  2118. *
  2119. * *** CAUTION ***
  2120. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  2121. * as the Arduino cannot handle the current the LEDs will require.
  2122. * Failure to follow this precaution can destroy your Arduino!
  2123. * NOTE: A separate 5V power supply is required! The NeoPixel LED needs
  2124. * more current than the Arduino 5V linear regulator can produce.
  2125. * *** CAUTION ***
  2126. *
  2127. * LED Type. Enable only one of the following two options.
  2128. */
  2129. //#define RGB_LED
  2130. //#define RGBW_LED
  2131. #if EITHER(RGB_LED, RGBW_LED)
  2132. //#define RGB_LED_R_PIN 34
  2133. //#define RGB_LED_G_PIN 43
  2134. //#define RGB_LED_B_PIN 35
  2135. //#define RGB_LED_W_PIN -1
  2136. #endif
  2137. // Support for Adafruit NeoPixel LED driver
  2138. //#define NEOPIXEL_LED
  2139. #if ENABLED(NEOPIXEL_LED)
  2140. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  2141. #define NEOPIXEL_PIN 4 // LED driving pin
  2142. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  2143. //#define NEOPIXEL2_PIN 5
  2144. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
  2145. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  2146. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  2147. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  2148. // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
  2149. //#define NEOPIXEL2_SEPARATE
  2150. #if ENABLED(NEOPIXEL2_SEPARATE)
  2151. #define NEOPIXEL2_PIXELS 15 // Number of LEDs in the second strip
  2152. #define NEOPIXEL2_BRIGHTNESS 127 // Initial brightness (0-255)
  2153. #define NEOPIXEL2_STARTUP_TEST // Cycle through colors at startup
  2154. #else
  2155. //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel
  2156. #endif
  2157. // Use a single NeoPixel LED for static (background) lighting
  2158. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  2159. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  2160. #endif
  2161. /**
  2162. * Printer Event LEDs
  2163. *
  2164. * During printing, the LEDs will reflect the printer status:
  2165. *
  2166. * - Gradually change from blue to violet as the heated bed gets to target temp
  2167. * - Gradually change from violet to red as the hotend gets to temperature
  2168. * - Change to white to illuminate work surface
  2169. * - Change to green once print has finished
  2170. * - Turn off after the print has finished and the user has pushed a button
  2171. */
  2172. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  2173. #define PRINTER_EVENT_LEDS
  2174. #endif
  2175. /**
  2176. * Number of servos
  2177. *
  2178. * For some servo-related options NUM_SERVOS will be set automatically.
  2179. * Set this manually if there are extra servos needing manual control.
  2180. * Set to 0 to turn off servo support.
  2181. */
  2182. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  2183. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  2184. // 300ms is a good value but you can try less delay.
  2185. // If the servo can't reach the requested position, increase it.
  2186. #define SERVO_DELAY { 300 }
  2187. // Only power servos during movement, otherwise leave off to prevent jitter
  2188. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  2189. // Edit servo angles with M281 and save to EEPROM with M500
  2190. //#define EDITABLE_SERVO_ANGLES