My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Ви не можете вибрати більше 25 тем Теми мають розпочинатися з літери або цифри, можуть містити дефіси (-) і не повинні перевищувати 35 символів.

Configuration_adv.h 107KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397139813991400140114021403140414051406140714081409141014111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472147314741475147614771478147914801481148214831484148514861487148814891490149114921493149414951496149714981499150015011502150315041505150615071508150915101511151215131514151515161517151815191520152115221523152415251526152715281529153015311532153315341535153615371538153915401541154215431544154515461547154815491550155115521553155415551556155715581559156015611562156315641565156615671568156915701571157215731574157515761577157815791580158115821583158415851586158715881589159015911592159315941595159615971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628162916301631163216331634163516361637163816391640164116421643164416451646164716481649165016511652165316541655165616571658165916601661166216631664166516661667166816691670167116721673167416751676167716781679168016811682168316841685168616871688168916901691169216931694169516961697169816991700170117021703170417051706170717081709171017111712171317141715171617171718171917201721172217231724172517261727172817291730173117321733173417351736173717381739174017411742174317441745174617471748174917501751175217531754175517561757175817591760176117621763176417651766176717681769177017711772177317741775177617771778177917801781178217831784178517861787178817891790179117921793179417951796179717981799180018011802180318041805180618071808180918101811181218131814181518161817181818191820182118221823182418251826182718281829183018311832183318341835183618371838183918401841184218431844184518461847184818491850185118521853185418551856185718581859186018611862186318641865186618671868186918701871187218731874187518761877187818791880188118821883188418851886188718881889189018911892189318941895189618971898189919001901190219031904190519061907190819091910191119121913191419151916191719181919192019211922192319241925192619271928192919301931193219331934193519361937193819391940194119421943194419451946194719481949195019511952195319541955195619571958195919601961196219631964196519661967196819691970197119721973197419751976197719781979198019811982198319841985198619871988198919901991199219931994199519961997199819992000200120022003200420052006200720082009201020112012201320142015201620172018201920202021202220232024202520262027202820292030203120322033203420352036203720382039204020412042204320442045204620472048204920502051205220532054205520562057205820592060206120622063206420652066206720682069207020712072207320742075207620772078207920802081208220832084208520862087208820892090209120922093209420952096209720982099210021012102210321042105210621072108210921102111211221132114211521162117211821192120212121222123212421252126212721282129213021312132213321342135213621372138213921402141214221432144214521462147214821492150215121522153215421552156215721582159216021612162216321642165216621672168216921702171217221732174217521762177217821792180218121822183218421852186218721882189219021912192219321942195219621972198219922002201220222032204220522062207220822092210221122122213221422152216221722182219222022212222222322242225222622272228222922302231223222332234223522362237223822392240224122422243224422452246224722482249225022512252225322542255225622572258225922602261226222632264226522662267226822692270227122722273227422752276227722782279228022812282228322842285228622872288228922902291229222932294229522962297229822992300230123022303230423052306230723082309231023112312231323142315231623172318231923202321232223232324232523262327232823292330233123322333233423352336233723382339234023412342234323442345234623472348234923502351235223532354235523562357235823592360236123622363236423652366236723682369237023712372237323742375237623772378237923802381238223832384238523862387238823892390239123922393239423952396239723982399240024012402240324042405240624072408240924102411241224132414241524162417241824192420242124222423242424252426242724282429243024312432243324342435243624372438243924402441244224432444244524462447244824492450245124522453245424552456245724582459246024612462246324642465246624672468246924702471247224732474247524762477247824792480248124822483248424852486248724882489249024912492249324942495249624972498249925002501250225032504250525062507250825092510251125122513251425152516251725182519252025212522252325242525252625272528252925302531253225332534253525362537253825392540254125422543254425452546254725482549255025512552255325542555255625572558255925602561256225632564256525662567256825692570257125722573257425752576257725782579258025812582258325842585258625872588258925902591259225932594259525962597259825992600260126022603260426052606260726082609261026112612261326142615261626172618261926202621262226232624262526262627262826292630263126322633263426352636263726382639264026412642264326442645264626472648264926502651265226532654265526562657265826592660266126622663266426652666266726682669267026712672267326742675267626772678267926802681268226832684268526862687268826892690269126922693269426952696269726982699270027012702270327042705270627072708270927102711271227132714271527162717271827192720272127222723272427252726272727282729273027312732273327342735273627372738273927402741274227432744274527462747274827492750275127522753275427552756275727582759276027612762276327642765
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration_adv.h
  25. *
  26. * Advanced settings.
  27. * Only change these if you know exactly what you're doing.
  28. * Some of these settings can damage your printer if improperly set!
  29. *
  30. * Basic settings can be found in Configuration.h
  31. *
  32. */
  33. #define CONFIGURATION_ADV_H_VERSION 020000
  34. // @section temperature
  35. //===========================================================================
  36. //=============================Thermal Settings ============================
  37. //===========================================================================
  38. //
  39. // Custom Thermistor 1000 parameters
  40. //
  41. #if TEMP_SENSOR_0 == 1000
  42. #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  43. #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  44. #define HOTEND0_BETA 3950 // Beta value
  45. #endif
  46. #if TEMP_SENSOR_1 == 1000
  47. #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  48. #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  49. #define HOTEND1_BETA 3950 // Beta value
  50. #endif
  51. #if TEMP_SENSOR_2 == 1000
  52. #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  53. #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  54. #define HOTEND2_BETA 3950 // Beta value
  55. #endif
  56. #if TEMP_SENSOR_3 == 1000
  57. #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  58. #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  59. #define HOTEND3_BETA 3950 // Beta value
  60. #endif
  61. #if TEMP_SENSOR_4 == 1000
  62. #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  63. #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  64. #define HOTEND4_BETA 3950 // Beta value
  65. #endif
  66. #if TEMP_SENSOR_5 == 1000
  67. #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  68. #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  69. #define HOTEND5_BETA 3950 // Beta value
  70. #endif
  71. #if TEMP_SENSOR_BED == 1000
  72. #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  73. #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  74. #define BED_BETA 3950 // Beta value
  75. #endif
  76. #if TEMP_SENSOR_CHAMBER == 1000
  77. #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  78. #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  79. #define CHAMBER_BETA 3950 // Beta value
  80. #endif
  81. //
  82. // Hephestos 2 24V heated bed upgrade kit.
  83. // https://store.bq.com/en/heated-bed-kit-hephestos2
  84. //
  85. //#define HEPHESTOS2_HEATED_BED_KIT
  86. #if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
  87. #undef TEMP_SENSOR_BED
  88. #define TEMP_SENSOR_BED 70
  89. #define HEATER_BED_INVERTING true
  90. #endif
  91. /**
  92. * Heated Chamber settings
  93. */
  94. #if TEMP_SENSOR_CHAMBER
  95. #define CHAMBER_MINTEMP 5
  96. #define CHAMBER_MAXTEMP 60
  97. #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
  98. //#define CHAMBER_LIMIT_SWITCHING
  99. //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
  100. //#define HEATER_CHAMBER_INVERTING false
  101. #endif
  102. #if DISABLED(PIDTEMPBED)
  103. #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
  104. #if ENABLED(BED_LIMIT_SWITCHING)
  105. #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
  106. #endif
  107. #endif
  108. /**
  109. * Thermal Protection provides additional protection to your printer from damage
  110. * and fire. Marlin always includes safe min and max temperature ranges which
  111. * protect against a broken or disconnected thermistor wire.
  112. *
  113. * The issue: If a thermistor falls out, it will report the much lower
  114. * temperature of the air in the room, and the the firmware will keep
  115. * the heater on.
  116. *
  117. * The solution: Once the temperature reaches the target, start observing.
  118. * If the temperature stays too far below the target (hysteresis) for too
  119. * long (period), the firmware will halt the machine as a safety precaution.
  120. *
  121. * If you get false positives for "Thermal Runaway", increase
  122. * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  123. */
  124. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  125. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  126. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  127. //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
  128. #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
  129. //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
  130. #endif
  131. /**
  132. * Whenever an M104, M109, or M303 increases the target temperature, the
  133. * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
  134. * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
  135. * requires a hard reset. This test restarts with any M104/M109/M303, but only
  136. * if the current temperature is far enough below the target for a reliable
  137. * test.
  138. *
  139. * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
  140. * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
  141. * below 2.
  142. */
  143. #define WATCH_TEMP_PERIOD 20 // Seconds
  144. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  145. #endif
  146. /**
  147. * Thermal Protection parameters for the bed are just as above for hotends.
  148. */
  149. #if ENABLED(THERMAL_PROTECTION_BED)
  150. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  151. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  152. /**
  153. * As described above, except for the bed (M140/M190/M303).
  154. */
  155. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  156. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  157. #endif
  158. /**
  159. * Thermal Protection parameters for the heated chamber.
  160. */
  161. #if ENABLED(THERMAL_PROTECTION_CHAMBER)
  162. #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
  163. #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
  164. /**
  165. * Heated chamber watch settings (M141/M191).
  166. */
  167. #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
  168. #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
  169. #endif
  170. #if ENABLED(PIDTEMP)
  171. // Add an experimental additional term to the heater power, proportional to the extrusion speed.
  172. // A well-chosen Kc value should add just enough power to melt the increased material volume.
  173. //#define PID_EXTRUSION_SCALING
  174. #if ENABLED(PID_EXTRUSION_SCALING)
  175. #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
  176. #define LPQ_MAX_LEN 50
  177. #endif
  178. #endif
  179. /**
  180. * Automatic Temperature:
  181. * The hotend target temperature is calculated by all the buffered lines of gcode.
  182. * The maximum buffered steps/sec of the extruder motor is called "se".
  183. * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
  184. * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
  185. * mintemp and maxtemp. Turn this off by executing M109 without F*
  186. * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
  187. * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
  188. */
  189. #define AUTOTEMP
  190. #if ENABLED(AUTOTEMP)
  191. #define AUTOTEMP_OLDWEIGHT 0.98
  192. #endif
  193. // Show extra position information with 'M114 D'
  194. //#define M114_DETAIL
  195. // Show Temperature ADC value
  196. // Enable for M105 to include ADC values read from temperature sensors.
  197. //#define SHOW_TEMP_ADC_VALUES
  198. /**
  199. * High Temperature Thermistor Support
  200. *
  201. * Thermistors able to support high temperature tend to have a hard time getting
  202. * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
  203. * will probably be caught when the heating element first turns on during the
  204. * preheating process, which will trigger a min_temp_error as a safety measure
  205. * and force stop everything.
  206. * To circumvent this limitation, we allow for a preheat time (during which,
  207. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  208. * aberrant readings.
  209. *
  210. * If you want to enable this feature for your hotend thermistor(s)
  211. * uncomment and set values > 0 in the constants below
  212. */
  213. // The number of consecutive low temperature errors that can occur
  214. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  215. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  216. // The number of milliseconds a hotend will preheat before starting to check
  217. // the temperature. This value should NOT be set to the time it takes the
  218. // hot end to reach the target temperature, but the time it takes to reach
  219. // the minimum temperature your thermistor can read. The lower the better/safer.
  220. // This shouldn't need to be more than 30 seconds (30000)
  221. //#define MILLISECONDS_PREHEAT_TIME 0
  222. // @section extruder
  223. // Extruder runout prevention.
  224. // If the machine is idle and the temperature over MINTEMP
  225. // then extrude some filament every couple of SECONDS.
  226. //#define EXTRUDER_RUNOUT_PREVENT
  227. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  228. #define EXTRUDER_RUNOUT_MINTEMP 190
  229. #define EXTRUDER_RUNOUT_SECONDS 30
  230. #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m)
  231. #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm)
  232. #endif
  233. // @section temperature
  234. // Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
  235. // The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
  236. #define TEMP_SENSOR_AD595_OFFSET 0.0
  237. #define TEMP_SENSOR_AD595_GAIN 1.0
  238. #define TEMP_SENSOR_AD8495_OFFSET 0.0
  239. #define TEMP_SENSOR_AD8495_GAIN 1.0
  240. /**
  241. * Controller Fan
  242. * To cool down the stepper drivers and MOSFETs.
  243. *
  244. * The fan will turn on automatically whenever any stepper is enabled
  245. * and turn off after a set period after all steppers are turned off.
  246. */
  247. //#define USE_CONTROLLER_FAN
  248. #if ENABLED(USE_CONTROLLER_FAN)
  249. //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
  250. #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
  251. #define CONTROLLERFAN_SPEED 255 // 255 == full speed
  252. //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled
  253. #endif
  254. // When first starting the main fan, run it at full speed for the
  255. // given number of milliseconds. This gets the fan spinning reliably
  256. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  257. //#define FAN_KICKSTART_TIME 100
  258. /**
  259. * PWM Fan Scaling
  260. *
  261. * Define the min/max speeds for PWM fans (as set with M106).
  262. *
  263. * With these options the M106 0-255 value range is scaled to a subset
  264. * to ensure that the fan has enough power to spin, or to run lower
  265. * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
  266. * Value 0 always turns off the fan.
  267. *
  268. * Define one or both of these to override the default 0-255 range.
  269. */
  270. //#define FAN_MIN_PWM 50
  271. //#define FAN_MAX_PWM 128
  272. /**
  273. * FAST PWM FAN Settings
  274. *
  275. * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
  276. * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
  277. * frequency as close as possible to the desired frequency.
  278. *
  279. * FAST_PWM_FAN_FREQUENCY [undefined by default]
  280. * Set this to your desired frequency.
  281. * If left undefined this defaults to F = F_CPU/(2*255*1)
  282. * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
  283. * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
  284. * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
  285. *
  286. * USE_OCR2A_AS_TOP [undefined by default]
  287. * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
  288. * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz]
  289. * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz]
  290. * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of
  291. * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  292. * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  293. */
  294. #if ENABLED(FAST_PWM_FAN)
  295. //#define FAST_PWM_FAN_FREQUENCY 31400
  296. //#define USE_OCR2A_AS_TOP
  297. #endif
  298. // @section extruder
  299. /**
  300. * Extruder cooling fans
  301. *
  302. * Extruder auto fans automatically turn on when their extruders'
  303. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  304. *
  305. * Your board's pins file specifies the recommended pins. Override those here
  306. * or set to -1 to disable completely.
  307. *
  308. * Multiple extruders can be assigned to the same pin in which case
  309. * the fan will turn on when any selected extruder is above the threshold.
  310. */
  311. #define E0_AUTO_FAN_PIN -1
  312. #define E1_AUTO_FAN_PIN -1
  313. #define E2_AUTO_FAN_PIN -1
  314. #define E3_AUTO_FAN_PIN -1
  315. #define E4_AUTO_FAN_PIN -1
  316. #define E5_AUTO_FAN_PIN -1
  317. #define CHAMBER_AUTO_FAN_PIN -1
  318. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  319. #define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
  320. #define CHAMBER_AUTO_FAN_TEMPERATURE 30
  321. #define CHAMBER_AUTO_FAN_SPEED 255
  322. /**
  323. * Part-Cooling Fan Multiplexer
  324. *
  325. * This feature allows you to digitally multiplex the fan output.
  326. * The multiplexer is automatically switched at tool-change.
  327. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  328. */
  329. #define FANMUX0_PIN -1
  330. #define FANMUX1_PIN -1
  331. #define FANMUX2_PIN -1
  332. /**
  333. * M355 Case Light on-off / brightness
  334. */
  335. //#define CASE_LIGHT_ENABLE
  336. #if ENABLED(CASE_LIGHT_ENABLE)
  337. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  338. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  339. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  340. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  341. //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm
  342. //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
  343. //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
  344. //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED.
  345. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
  346. #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
  347. #endif
  348. #endif
  349. // @section homing
  350. // If you want endstops to stay on (by default) even when not homing
  351. // enable this option. Override at any time with M120, M121.
  352. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  353. // @section extras
  354. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  355. // Employ an external closed loop controller. Override pins here if needed.
  356. //#define EXTERNAL_CLOSED_LOOP_CONTROLLER
  357. #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
  358. //#define CLOSED_LOOP_ENABLE_PIN -1
  359. //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
  360. #endif
  361. /**
  362. * Dual Steppers / Dual Endstops
  363. *
  364. * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes.
  365. *
  366. * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to
  367. * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop
  368. * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug
  369. * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'.
  370. *
  371. * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors
  372. * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error
  373. * in X2. Dual endstop offsets can be set at runtime with 'M666 X<offset> Y<offset> Z<offset>'.
  374. */
  375. //#define X_DUAL_STEPPER_DRIVERS
  376. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  377. #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions
  378. //#define X_DUAL_ENDSTOPS
  379. #if ENABLED(X_DUAL_ENDSTOPS)
  380. #define X2_USE_ENDSTOP _XMAX_
  381. #define X_DUAL_ENDSTOPS_ADJUSTMENT 0
  382. #endif
  383. #endif
  384. //#define Y_DUAL_STEPPER_DRIVERS
  385. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  386. #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions
  387. //#define Y_DUAL_ENDSTOPS
  388. #if ENABLED(Y_DUAL_ENDSTOPS)
  389. #define Y2_USE_ENDSTOP _YMAX_
  390. #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0
  391. #endif
  392. #endif
  393. //#define Z_DUAL_STEPPER_DRIVERS
  394. #if ENABLED(Z_DUAL_STEPPER_DRIVERS)
  395. //#define Z_DUAL_ENDSTOPS
  396. #if ENABLED(Z_DUAL_ENDSTOPS)
  397. #define Z2_USE_ENDSTOP _XMAX_
  398. #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0
  399. #endif
  400. #endif
  401. //#define Z_TRIPLE_STEPPER_DRIVERS
  402. #if ENABLED(Z_TRIPLE_STEPPER_DRIVERS)
  403. //#define Z_TRIPLE_ENDSTOPS
  404. #if ENABLED(Z_TRIPLE_ENDSTOPS)
  405. #define Z2_USE_ENDSTOP _XMAX_
  406. #define Z3_USE_ENDSTOP _YMAX_
  407. #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0
  408. #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0
  409. #endif
  410. #endif
  411. /**
  412. * Dual X Carriage
  413. *
  414. * This setup has two X carriages that can move independently, each with its own hotend.
  415. * The carriages can be used to print an object with two colors or materials, or in
  416. * "duplication mode" it can print two identical or X-mirrored objects simultaneously.
  417. * The inactive carriage is parked automatically to prevent oozing.
  418. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
  419. * By default the X2 stepper is assigned to the first unused E plug on the board.
  420. *
  421. * The following Dual X Carriage modes can be selected with M605 S<mode>:
  422. *
  423. * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel
  424. * results as long as it supports dual X-carriages. (M605 S0)
  425. *
  426. * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so
  427. * that additional slicer support is not required. (M605 S1)
  428. *
  429. * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with
  430. * the first X-carriage and extruder, to print 2 copies of the same object at the same time.
  431. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
  432. * follow with M605 S2 to initiate duplicated movement.
  433. *
  434. * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates
  435. * the movement of the first except the second extruder is reversed in the X axis.
  436. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  437. * follow with M605 S3 to initiate mirrored movement.
  438. */
  439. //#define DUAL_X_CARRIAGE
  440. #if ENABLED(DUAL_X_CARRIAGE)
  441. #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS
  442. #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage
  443. #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage
  444. #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed
  445. #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position
  446. #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
  447. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  448. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  449. // without modifying the firmware (through the "M218 T1 X???" command).
  450. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  451. // This is the default power-up mode which can be later using M605.
  452. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
  453. // Default x offset in duplication mode (typically set to half print bed width)
  454. #define DEFAULT_DUPLICATION_X_OFFSET 100
  455. #endif // DUAL_X_CARRIAGE
  456. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  457. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  458. //#define EXT_SOLENOID
  459. // @section homing
  460. // Homing hits each endstop, retracts by these distances, then does a slower bump.
  461. #define X_HOME_BUMP_MM 5
  462. #define Y_HOME_BUMP_MM 5
  463. #define Z_HOME_BUMP_MM 2
  464. #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  465. //#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
  466. //#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing
  467. // When G28 is called, this option will make Y home before X
  468. //#define HOME_Y_BEFORE_X
  469. // Enable this if X or Y can't home without homing the other axis first.
  470. //#define CODEPENDENT_XY_HOMING
  471. #if ENABLED(BLTOUCH)
  472. /**
  473. * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
  474. * Do not activate settings that the probe might not understand. Clones might misunderstand
  475. * advanced commands.
  476. *
  477. * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
  478. * check the wiring of the BROWN, RED and ORANGE wires.
  479. *
  480. * Note: If the trigger signal of your probe is not being recognized, it has been very often
  481. * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
  482. * like they would be with a real switch. So please check the wiring first.
  483. *
  484. * Settings for all BLTouch and clone probes:
  485. */
  486. // Safety: The probe needs time to recognize the command.
  487. // Minimum command delay (ms). Enable and increase if needed.
  488. //#define BLTOUCH_DELAY 500
  489. /**
  490. * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
  491. */
  492. // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
  493. // in special cases, like noisy or filtered input configurations.
  494. //#define BLTOUCH_FORCE_SW_MODE
  495. /**
  496. * Settings for BLTouch Smart 3.0 and 3.1
  497. * Summary:
  498. * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
  499. * - High-Speed mode
  500. * - Disable LCD voltage options
  501. */
  502. /**
  503. * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
  504. * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
  505. * If disabled, OD mode is the hard-coded default on 3.0
  506. * On startup, Marlin will compare its eeprom to this vale. If the selected mode
  507. * differs, a mode set eeprom write will be completed at initialization.
  508. * Use the option below to force an eeprom write to a V3.1 probe regardless.
  509. */
  510. //#define BLTOUCH_SET_5V_MODE
  511. /**
  512. * Safety: Activate if connecting a probe with an unknown voltage mode.
  513. * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
  514. * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
  515. * To preserve the life of the probe, use this once then turn it off and re-flash.
  516. */
  517. //#define BLTOUCH_FORCE_MODE_SET
  518. /**
  519. * Use "HIGH SPEED" mode for probing.
  520. * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
  521. * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
  522. * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
  523. */
  524. //#define BLTOUCH_HS_MODE
  525. // Safety: Enable voltage mode settings in the LCD menu.
  526. //#define BLTOUCH_LCD_VOLTAGE_MENU
  527. #endif // BLTOUCH
  528. /**
  529. * Z Steppers Auto-Alignment
  530. * Add the G34 command to align multiple Z steppers using a bed probe.
  531. */
  532. //#define Z_STEPPER_AUTO_ALIGN
  533. #if ENABLED(Z_STEPPER_AUTO_ALIGN)
  534. // Define probe X and Y positions for Z1, Z2 [, Z3]
  535. #define Z_STEPPER_ALIGN_XY { { 10, 290 }, { 150, 10 }, { 290, 290 } } // Set number of iterations to align
  536. #define Z_STEPPER_ALIGN_ITERATIONS 3
  537. // Enable to restore leveling setup after operation
  538. #define RESTORE_LEVELING_AFTER_G34
  539. // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
  540. #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle
  541. // Use the amplification factor to de-/increase correction step.
  542. // In case the stepper (spindle) position is further out than the test point
  543. // Use a value > 1. NOTE: This may cause instability
  544. #define Z_STEPPER_ALIGN_AMP 1.0
  545. // Stop criterion. If the accuracy is better than this stop iterating early
  546. #define Z_STEPPER_ALIGN_ACC 0.02
  547. #endif
  548. // @section motion
  549. #define AXIS_RELATIVE_MODES { false, false, false, false }
  550. // Add a Duplicate option for well-separated conjoined nozzles
  551. //#define MULTI_NOZZLE_DUPLICATION
  552. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  553. #define INVERT_X_STEP_PIN false
  554. #define INVERT_Y_STEP_PIN false
  555. #define INVERT_Z_STEP_PIN false
  556. #define INVERT_E_STEP_PIN false
  557. // Default stepper release if idle. Set to 0 to deactivate.
  558. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
  559. // Time can be set by M18 and M84.
  560. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  561. #define DISABLE_INACTIVE_X true
  562. #define DISABLE_INACTIVE_Y true
  563. #define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished.
  564. #define DISABLE_INACTIVE_E true
  565. #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
  566. #define DEFAULT_MINTRAVELFEEDRATE 0.0
  567. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
  568. // Minimum time that a segment needs to take if the buffer is emptied
  569. #define DEFAULT_MINSEGMENTTIME 20000 // (ms)
  570. // If defined the movements slow down when the look ahead buffer is only half full
  571. #define SLOWDOWN
  572. // Frequency limit
  573. // See nophead's blog for more info
  574. // Not working O
  575. //#define XY_FREQUENCY_LIMIT 15
  576. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  577. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  578. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  579. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
  580. //
  581. // Backlash Compensation
  582. // Adds extra movement to axes on direction-changes to account for backlash.
  583. //
  584. //#define BACKLASH_COMPENSATION
  585. #if ENABLED(BACKLASH_COMPENSATION)
  586. // Define values for backlash distance and correction.
  587. // If BACKLASH_GCODE is enabled these values are the defaults.
  588. #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm)
  589. #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
  590. // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments
  591. // to reduce print artifacts. (Enabling this is costly in memory and computation!)
  592. //#define BACKLASH_SMOOTHING_MM 3 // (mm)
  593. // Add runtime configuration and tuning of backlash values (M425)
  594. //#define BACKLASH_GCODE
  595. #if ENABLED(BACKLASH_GCODE)
  596. // Measure the Z backlash when probing (G29) and set with "M425 Z"
  597. #define MEASURE_BACKLASH_WHEN_PROBING
  598. #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
  599. // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
  600. // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION
  601. // increments while checking for the contact to be broken.
  602. #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm)
  603. #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm)
  604. #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m)
  605. #endif
  606. #endif
  607. #endif
  608. /**
  609. * Automatic backlash, position and hotend offset calibration
  610. *
  611. * Enable G425 to run automatic calibration using an electrically-
  612. * conductive cube, bolt, or washer mounted on the bed.
  613. *
  614. * G425 uses the probe to touch the top and sides of the calibration object
  615. * on the bed and measures and/or correct positional offsets, axis backlash
  616. * and hotend offsets.
  617. *
  618. * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
  619. * ±5mm of true values for G425 to succeed.
  620. */
  621. //#define CALIBRATION_GCODE
  622. #if ENABLED(CALIBRATION_GCODE)
  623. #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm
  624. #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m
  625. #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m
  626. #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m
  627. // The following parameters refer to the conical section of the nozzle tip.
  628. #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
  629. #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
  630. // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
  631. //#define CALIBRATION_REPORTING
  632. // The true location and dimension the cube/bolt/washer on the bed.
  633. #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
  634. #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
  635. // Comment out any sides which are unreachable by the probe. For best
  636. // auto-calibration results, all sides must be reachable.
  637. #define CALIBRATION_MEASURE_RIGHT
  638. #define CALIBRATION_MEASURE_FRONT
  639. #define CALIBRATION_MEASURE_LEFT
  640. #define CALIBRATION_MEASURE_BACK
  641. // Probing at the exact top center only works if the center is flat. If
  642. // probing on a screwhead or hollow washer, probe near the edges.
  643. //#define CALIBRATION_MEASURE_AT_TOP_EDGES
  644. // Define pin which is read during calibration
  645. #ifndef CALIBRATION_PIN
  646. #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
  647. #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
  648. //#define CALIBRATION_PIN_PULLDOWN
  649. #define CALIBRATION_PIN_PULLUP
  650. #endif
  651. #endif
  652. /**
  653. * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
  654. * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
  655. * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  656. * lowest stepping frequencies.
  657. */
  658. //#define ADAPTIVE_STEP_SMOOTHING
  659. /**
  660. * Custom Microstepping
  661. * Override as-needed for your setup. Up to 3 MS pins are supported.
  662. */
  663. //#define MICROSTEP1 LOW,LOW,LOW
  664. //#define MICROSTEP2 HIGH,LOW,LOW
  665. //#define MICROSTEP4 LOW,HIGH,LOW
  666. //#define MICROSTEP8 HIGH,HIGH,LOW
  667. //#define MICROSTEP16 LOW,LOW,HIGH
  668. //#define MICROSTEP32 HIGH,LOW,HIGH
  669. // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
  670. #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
  671. /**
  672. * @section stepper motor current
  673. *
  674. * Some boards have a means of setting the stepper motor current via firmware.
  675. *
  676. * The power on motor currents are set by:
  677. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  678. * known compatible chips: A4982
  679. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  680. * known compatible chips: AD5206
  681. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  682. * known compatible chips: MCP4728
  683. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE
  684. * known compatible chips: MCP4451, MCP4018
  685. *
  686. * Motor currents can also be set by M907 - M910 and by the LCD.
  687. * M907 - applies to all.
  688. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  689. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  690. */
  691. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  692. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  693. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  694. // Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro)
  695. //#define DIGIPOT_I2C
  696. #if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A)
  697. /**
  698. * Common slave addresses:
  699. *
  700. * A (A shifted) B (B shifted) IC
  701. * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
  702. * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
  703. * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451
  704. * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451
  705. * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
  706. */
  707. #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT
  708. #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT
  709. #endif
  710. //#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
  711. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5
  712. // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
  713. // These correspond to the physical drivers, so be mindful if the order is changed.
  714. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  715. //===========================================================================
  716. //=============================Additional Features===========================
  717. //===========================================================================
  718. // @section lcd
  719. #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
  720. #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
  721. #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
  722. #if ENABLED(ULTIPANEL)
  723. #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
  724. #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen
  725. #endif
  726. #endif
  727. // Change values more rapidly when the encoder is rotated faster
  728. #define ENCODER_RATE_MULTIPLIER
  729. #if ENABLED(ENCODER_RATE_MULTIPLIER)
  730. #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed
  731. #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
  732. #endif
  733. // Play a beep when the feedrate is changed from the Status Screen
  734. //#define BEEP_ON_FEEDRATE_CHANGE
  735. #if ENABLED(BEEP_ON_FEEDRATE_CHANGE)
  736. #define FEEDRATE_CHANGE_BEEP_DURATION 10
  737. #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
  738. #endif
  739. #if HAS_LCD_MENU
  740. // Include a page of printer information in the LCD Main Menu
  741. //#define LCD_INFO_MENU
  742. #if ENABLED(LCD_INFO_MENU)
  743. //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
  744. #endif
  745. // BACK menu items keep the highlight at the top
  746. //#define TURBO_BACK_MENU_ITEM
  747. /**
  748. * LED Control Menu
  749. * Add LED Control to the LCD menu
  750. */
  751. //#define LED_CONTROL_MENU
  752. #if ENABLED(LED_CONTROL_MENU)
  753. #define LED_COLOR_PRESETS // Enable the Preset Color menu option
  754. #if ENABLED(LED_COLOR_PRESETS)
  755. #define LED_USER_PRESET_RED 255 // User defined RED value
  756. #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
  757. #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
  758. #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
  759. #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  760. //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
  761. #endif
  762. #endif
  763. #endif // HAS_LCD_MENU
  764. // Scroll a longer status message into view
  765. //#define STATUS_MESSAGE_SCROLLING
  766. // On the Info Screen, display XY with one decimal place when possible
  767. //#define LCD_DECIMAL_SMALL_XY
  768. // The timeout (in ms) to return to the status screen from sub-menus
  769. //#define LCD_TIMEOUT_TO_STATUS 15000
  770. // Add an 'M73' G-code to set the current percentage
  771. //#define LCD_SET_PROGRESS_MANUALLY
  772. #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
  773. //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
  774. #if ENABLED(LCD_PROGRESS_BAR)
  775. #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
  776. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
  777. #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
  778. //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
  779. //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
  780. #endif
  781. #endif
  782. #if ENABLED(SDSUPPORT)
  783. // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
  784. // around this by connecting a push button or single throw switch to the pin defined
  785. // as SD_DETECT_PIN in your board's pins definitions.
  786. // This setting should be disabled unless you are using a push button, pulling the pin to ground.
  787. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
  788. #define SD_DETECT_INVERTED
  789. #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
  790. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
  791. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
  792. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
  793. #define SDCARD_RATHERRECENTFIRST
  794. #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
  795. //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
  796. #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
  797. /**
  798. * Continue after Power-Loss (Creality3D)
  799. *
  800. * Store the current state to the SD Card at the start of each layer
  801. * during SD printing. If the recovery file is found at boot time, present
  802. * an option on the LCD screen to continue the print from the last-known
  803. * point in the file.
  804. */
  805. //#define POWER_LOSS_RECOVERY
  806. #if ENABLED(POWER_LOSS_RECOVERY)
  807. //#define POWER_LOSS_PIN 44 // Pin to detect power loss
  808. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
  809. //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
  810. //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
  811. //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
  812. // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
  813. // especially with "vase mode" printing. Set too high and vases cannot be continued.
  814. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
  815. #endif
  816. /**
  817. * Sort SD file listings in alphabetical order.
  818. *
  819. * With this option enabled, items on SD cards will be sorted
  820. * by name for easier navigation.
  821. *
  822. * By default...
  823. *
  824. * - Use the slowest -but safest- method for sorting.
  825. * - Folders are sorted to the top.
  826. * - The sort key is statically allocated.
  827. * - No added G-code (M34) support.
  828. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  829. *
  830. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  831. * compiler to calculate the worst-case usage and throw an error if the SRAM
  832. * limit is exceeded.
  833. *
  834. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  835. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  836. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  837. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  838. */
  839. //#define SDCARD_SORT_ALPHA
  840. // SD Card Sorting options
  841. #if ENABLED(SDCARD_SORT_ALPHA)
  842. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  843. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  844. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
  845. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  846. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  847. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  848. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  849. #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
  850. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
  851. #endif
  852. // This allows hosts to request long names for files and folders with M33
  853. //#define LONG_FILENAME_HOST_SUPPORT
  854. // Enable this option to scroll long filenames in the SD card menu
  855. //#define SCROLL_LONG_FILENAMES
  856. // Leave the heaters on after Stop Print (not recommended!)
  857. //#define SD_ABORT_NO_COOLDOWN
  858. /**
  859. * This option allows you to abort SD printing when any endstop is triggered.
  860. * This feature must be enabled with "M540 S1" or from the LCD menu.
  861. * To have any effect, endstops must be enabled during SD printing.
  862. */
  863. //#define SD_ABORT_ON_ENDSTOP_HIT
  864. /**
  865. * This option makes it easier to print the same SD Card file again.
  866. * On print completion the LCD Menu will open with the file selected.
  867. * You can just click to start the print, or navigate elsewhere.
  868. */
  869. //#define SD_REPRINT_LAST_SELECTED_FILE
  870. /**
  871. * Auto-report SdCard status with M27 S<seconds>
  872. */
  873. //#define AUTO_REPORT_SD_STATUS
  874. /**
  875. * Support for USB thumb drives using an Arduino USB Host Shield or
  876. * equivalent MAX3421E breakout board. The USB thumb drive will appear
  877. * to Marlin as an SD card.
  878. *
  879. * The MAX3421E can be assigned the same pins as the SD card reader, with
  880. * the following pin mapping:
  881. *
  882. * SCLK, MOSI, MISO --> SCLK, MOSI, MISO
  883. * INT --> SD_DETECT_PIN [1]
  884. * SS --> SDSS
  885. *
  886. * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility.
  887. */
  888. //#define USB_FLASH_DRIVE_SUPPORT
  889. #if ENABLED(USB_FLASH_DRIVE_SUPPORT)
  890. #define USB_CS_PIN SDSS
  891. #define USB_INTR_PIN SD_DETECT_PIN
  892. /**
  893. * USB Host Shield Library
  894. *
  895. * - UHS2 uses no interrupts and has been production-tested
  896. * on a LulzBot TAZ Pro with a 32-bit Archim board.
  897. *
  898. * - UHS3 is newer code with better USB compatibility. But it
  899. * is less tested and is known to interfere with Servos.
  900. * [1] This requires USB_INTR_PIN to be interrupt-capable.
  901. */
  902. //#define USE_UHS3_USB
  903. #endif
  904. /**
  905. * When using a bootloader that supports SD-Firmware-Flashing,
  906. * add a menu item to activate SD-FW-Update on the next reboot.
  907. *
  908. * Requires ATMEGA2560 (Arduino Mega)
  909. *
  910. * Tested with this bootloader:
  911. * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560
  912. */
  913. //#define SD_FIRMWARE_UPDATE
  914. #if ENABLED(SD_FIRMWARE_UPDATE)
  915. #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF
  916. #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0
  917. #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF
  918. #endif
  919. // Add an optimized binary file transfer mode, initiated with 'M28 B1'
  920. //#define BINARY_FILE_TRANSFER
  921. #if HAS_SDCARD_CONNECTION
  922. /**
  923. * Set this option to one of the following (or the board's defaults apply):
  924. *
  925. * LCD - Use the SD drive in the external LCD controller.
  926. * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
  927. * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
  928. *
  929. * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
  930. */
  931. //#define SDCARD_CONNECTION LCD
  932. #endif
  933. #endif // SDSUPPORT
  934. /**
  935. * By default an onboard SD card reader may be shared as a USB mass-
  936. * storage device. This option hides the SD card from the host PC.
  937. */
  938. //#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security).
  939. /**
  940. * Additional options for Graphical Displays
  941. *
  942. * Use the optimizations here to improve printing performance,
  943. * which can be adversely affected by graphical display drawing,
  944. * especially when doing several short moves, and when printing
  945. * on DELTA and SCARA machines.
  946. *
  947. * Some of these options may result in the display lagging behind
  948. * controller events, as there is a trade-off between reliable
  949. * printing performance versus fast display updates.
  950. */
  951. #if HAS_GRAPHICAL_LCD
  952. // Show SD percentage next to the progress bar
  953. //#define DOGM_SD_PERCENT
  954. // Enable to save many cycles by drawing a hollow frame on the Info Screen
  955. #define XYZ_HOLLOW_FRAME
  956. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  957. #define MENU_HOLLOW_FRAME
  958. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  959. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  960. //#define USE_BIG_EDIT_FONT
  961. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
  962. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  963. //#define USE_SMALL_INFOFONT
  964. // Enable this option and reduce the value to optimize screen updates.
  965. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  966. //#define DOGM_SPI_DELAY_US 5
  967. // Swap the CW/CCW indicators in the graphics overlay
  968. //#define OVERLAY_GFX_REVERSE
  969. /**
  970. * ST7920-based LCDs can emulate a 16 x 4 character display using
  971. * the ST7920 character-generator for very fast screen updates.
  972. * Enable LIGHTWEIGHT_UI to use this special display mode.
  973. *
  974. * Since LIGHTWEIGHT_UI has limited space, the position and status
  975. * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
  976. * length of time to display the status message before clearing.
  977. *
  978. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
  979. * This will prevent position updates from being displayed.
  980. */
  981. #if ENABLED(U8GLIB_ST7920)
  982. //#define LIGHTWEIGHT_UI
  983. #if ENABLED(LIGHTWEIGHT_UI)
  984. #define STATUS_EXPIRE_SECONDS 20
  985. #endif
  986. #endif
  987. /**
  988. * Status (Info) Screen customizations
  989. * These options may affect code size and screen render time.
  990. * Custom status screens can forcibly override these settings.
  991. */
  992. //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones
  993. //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends)
  994. #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM)
  995. #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating
  996. #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating
  997. #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating
  998. //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
  999. //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
  1000. //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
  1001. //#define STATUS_HEAT_PERCENT // Show heating in a progress bar
  1002. //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
  1003. //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
  1004. // Frivolous Game Options
  1005. //#define MARLIN_BRICKOUT
  1006. //#define MARLIN_INVADERS
  1007. //#define MARLIN_SNAKE
  1008. //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu
  1009. #endif // HAS_GRAPHICAL_LCD
  1010. //
  1011. // Lulzbot Touch UI
  1012. //
  1013. #if ENABLED(LULZBOT_TOUCH_UI)
  1014. // Display board used
  1015. //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240)
  1016. //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
  1017. //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272)
  1018. //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480)
  1019. //#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI
  1020. // Correct the resolution if not using the stock TFT panel.
  1021. //#define TOUCH_UI_320x240
  1022. //#define TOUCH_UI_480x272
  1023. //#define TOUCH_UI_800x480
  1024. // Mappings for boards with a standard RepRapDiscount Display connector
  1025. //#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping
  1026. //#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping
  1027. //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping
  1028. //#define OTHER_PIN_LAYOUT // Define pins manually below
  1029. #if ENABLED(OTHER_PIN_LAYOUT)
  1030. // The pins for CS and MOD_RESET (PD) must be chosen.
  1031. #define CLCD_MOD_RESET 9
  1032. #define CLCD_SPI_CS 10
  1033. // If using software SPI, specify pins for SCLK, MOSI, MISO
  1034. //#define CLCD_USE_SOFT_SPI
  1035. #if ENABLED(CLCD_USE_SOFT_SPI)
  1036. #define CLCD_SOFT_SPI_MOSI 11
  1037. #define CLCD_SOFT_SPI_MISO 12
  1038. #define CLCD_SOFT_SPI_SCLK 13
  1039. #endif
  1040. #endif
  1041. // Display Orientation. An inverted (i.e. upside-down) display
  1042. // is supported on the FT800. The FT810 and beyond also support
  1043. // portrait and mirrored orientations.
  1044. //#define TOUCH_UI_INVERTED
  1045. //#define TOUCH_UI_PORTRAIT
  1046. //#define TOUCH_UI_MIRRORED
  1047. // UTF8 processing and rendering.
  1048. // Unsupported characters are shown as '?'.
  1049. //#define TOUCH_UI_USE_UTF8
  1050. #if ENABLED(TOUCH_UI_USE_UTF8)
  1051. // Western accents support. These accented characters use
  1052. // combined bitmaps and require relatively little storage.
  1053. #define TOUCH_UI_UTF8_WESTERN_CHARSET
  1054. #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
  1055. // Additional character groups. These characters require
  1056. // full bitmaps and take up considerable storage:
  1057. //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³
  1058. //#define TOUCH_UI_UTF8_COPYRIGHT // © ®
  1059. //#define TOUCH_UI_UTF8_GERMANIC // ß
  1060. //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ
  1061. //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡
  1062. //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥
  1063. //#define TOUCH_UI_UTF8_ORDINALS // º ª
  1064. //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷
  1065. //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾
  1066. //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬
  1067. #endif
  1068. #endif
  1069. // Use a smaller font when labels don't fit buttons
  1070. #define TOUCH_UI_FIT_TEXT
  1071. // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE)
  1072. //#define LCD_LANGUAGE_1 en
  1073. //#define LCD_LANGUAGE_2 fr
  1074. //#define LCD_LANGUAGE_3 de
  1075. //#define LCD_LANGUAGE_4 es
  1076. //#define LCD_LANGUAGE_5 it
  1077. // Use a numeric passcode for "Screen lock" keypad.
  1078. // (recommended for smaller displays)
  1079. //#define TOUCH_UI_PASSCODE
  1080. // Output extra debug info for Touch UI events
  1081. //#define TOUCH_UI_DEBUG
  1082. #endif
  1083. //
  1084. // FSMC Graphical TFT
  1085. //
  1086. #if ENABLED(FSMC_GRAPHICAL_TFT)
  1087. //#define TFT_MARLINUI_COLOR 0xFFFF // White
  1088. //#define TFT_MARLINBG_COLOR 0x0000 // Black
  1089. //#define TFT_DISABLED_COLOR 0x0003 // Almost black
  1090. //#define TFT_BTCANCEL_COLOR 0xF800 // Red
  1091. //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow
  1092. //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
  1093. #endif
  1094. // @section safety
  1095. /**
  1096. * The watchdog hardware timer will do a reset and disable all outputs
  1097. * if the firmware gets too overloaded to read the temperature sensors.
  1098. *
  1099. * If you find that watchdog reboot causes your AVR board to hang forever,
  1100. * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
  1101. * NOTE: This method is less reliable as it can only catch hangups while
  1102. * interrupts are enabled.
  1103. */
  1104. #define USE_WATCHDOG
  1105. #if ENABLED(USE_WATCHDOG)
  1106. //#define WATCHDOG_RESET_MANUAL
  1107. #endif
  1108. // @section lcd
  1109. /**
  1110. * Babystepping enables movement of the axes by tiny increments without changing
  1111. * the current position values. This feature is used primarily to adjust the Z
  1112. * axis in the first layer of a print in real-time.
  1113. *
  1114. * Warning: Does not respect endstops!
  1115. */
  1116. //#define BABYSTEPPING
  1117. #if ENABLED(BABYSTEPPING)
  1118. //#define BABYSTEP_WITHOUT_HOMING
  1119. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  1120. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  1121. #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
  1122. //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  1123. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
  1124. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  1125. // Note: Extra time may be added to mitigate controller latency.
  1126. //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
  1127. //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
  1128. #if ENABLED(MOVE_Z_WHEN_IDLE)
  1129. #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
  1130. #endif
  1131. #endif
  1132. //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
  1133. //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
  1134. #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
  1135. //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
  1136. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  1137. #endif
  1138. #endif
  1139. // @section extruder
  1140. /**
  1141. * Linear Pressure Control v1.5
  1142. *
  1143. * Assumption: advance [steps] = k * (delta velocity [steps/s])
  1144. * K=0 means advance disabled.
  1145. *
  1146. * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
  1147. *
  1148. * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
  1149. * Larger K values will be needed for flexible filament and greater distances.
  1150. * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
  1151. * print acceleration will be reduced during the affected moves to keep within the limit.
  1152. *
  1153. * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
  1154. * Mention @Sebastianv650 on GitHub to alert the author of any issues.
  1155. */
  1156. //#define LIN_ADVANCE
  1157. #if ENABLED(LIN_ADVANCE)
  1158. //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
  1159. #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
  1160. //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
  1161. #endif
  1162. // @section leveling
  1163. /**
  1164. * Points to probe for all 3-point Leveling procedures.
  1165. * Override if the automatically selected points are inadequate.
  1166. */
  1167. #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
  1168. //#define PROBE_PT_1_X 15
  1169. //#define PROBE_PT_1_Y 180
  1170. //#define PROBE_PT_2_X 15
  1171. //#define PROBE_PT_2_Y 20
  1172. //#define PROBE_PT_3_X 170
  1173. //#define PROBE_PT_3_Y 20
  1174. #endif
  1175. /**
  1176. * Override MIN_PROBE_EDGE for each side of the build plate
  1177. * Useful to get probe points to exact positions on targets or
  1178. * to allow leveling to avoid plate clamps on only specific
  1179. * sides of the bed.
  1180. *
  1181. * If you are replacing the prior *_PROBE_BED_POSITION options,
  1182. * LEFT and FRONT values in most cases will map directly over
  1183. * RIGHT and REAR would be the inverse such as
  1184. * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
  1185. *
  1186. * This will allow all positions to match at compilation, however
  1187. * should the probe position be modified with M851XY then the
  1188. * probe points will follow. This prevents any change from causing
  1189. * the probe to be unable to reach any points.
  1190. */
  1191. #if PROBE_SELECTED && !IS_KINEMATIC && !IS_KINEMATIC
  1192. //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
  1193. //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
  1194. //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
  1195. //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
  1196. #endif
  1197. #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
  1198. // Override the mesh area if the automatic (max) area is too large
  1199. //#define MESH_MIN_X MESH_INSET
  1200. //#define MESH_MIN_Y MESH_INSET
  1201. //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
  1202. //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
  1203. #endif
  1204. /**
  1205. * Repeatedly attempt G29 leveling until it succeeds.
  1206. * Stop after G29_MAX_RETRIES attempts.
  1207. */
  1208. //#define G29_RETRY_AND_RECOVER
  1209. #if ENABLED(G29_RETRY_AND_RECOVER)
  1210. #define G29_MAX_RETRIES 3
  1211. #define G29_HALT_ON_FAILURE
  1212. /**
  1213. * Specify the GCODE commands that will be executed when leveling succeeds,
  1214. * between attempts, and after the maximum number of retries have been tried.
  1215. */
  1216. #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
  1217. #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
  1218. #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
  1219. #endif
  1220. // @section extras
  1221. //
  1222. // G2/G3 Arc Support
  1223. //
  1224. #define ARC_SUPPORT // Disable this feature to save ~3226 bytes
  1225. #if ENABLED(ARC_SUPPORT)
  1226. #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
  1227. #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle
  1228. #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections
  1229. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  1230. //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
  1231. #endif
  1232. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  1233. //#define BEZIER_CURVE_SUPPORT
  1234. /**
  1235. * G38 Probe Target
  1236. *
  1237. * This option adds G38.2 and G38.3 (probe towards target)
  1238. * and optionally G38.4 and G38.5 (probe away from target).
  1239. * Set MULTIPLE_PROBING for G38 to probe more than once.
  1240. */
  1241. //#define G38_PROBE_TARGET
  1242. #if ENABLED(G38_PROBE_TARGET)
  1243. //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target
  1244. #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move.
  1245. #endif
  1246. // Moves (or segments) with fewer steps than this will be joined with the next move
  1247. #define MIN_STEPS_PER_SEGMENT 6
  1248. /**
  1249. * Minimum delay before and after setting the stepper DIR (in ns)
  1250. * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
  1251. * 20 : Minimum for TMC2xxx drivers
  1252. * 200 : Minimum for A4988 drivers
  1253. * 400 : Minimum for A5984 drivers
  1254. * 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
  1255. * 650 : Minimum for DRV8825 drivers
  1256. * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
  1257. * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
  1258. *
  1259. * Override the default value based on the driver type set in Configuration.h.
  1260. */
  1261. //#define MINIMUM_STEPPER_POST_DIR_DELAY 650
  1262. //#define MINIMUM_STEPPER_PRE_DIR_DELAY 650
  1263. /**
  1264. * Minimum stepper driver pulse width (in µs)
  1265. * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
  1266. * 0 : Minimum 500ns for LV8729, adjusted in stepper.h
  1267. * 1 : Minimum for A4988 and A5984 stepper drivers
  1268. * 2 : Minimum for DRV8825 stepper drivers
  1269. * 3 : Minimum for TB6600 stepper drivers
  1270. * 30 : Minimum for TB6560 stepper drivers
  1271. *
  1272. * Override the default value based on the driver type set in Configuration.h.
  1273. */
  1274. //#define MINIMUM_STEPPER_PULSE 2
  1275. /**
  1276. * Maximum stepping rate (in Hz) the stepper driver allows
  1277. * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
  1278. * 500000 : Maximum for A4988 stepper driver
  1279. * 400000 : Maximum for TMC2xxx stepper drivers
  1280. * 250000 : Maximum for DRV8825 stepper driver
  1281. * 200000 : Maximum for LV8729 stepper driver
  1282. * 150000 : Maximum for TB6600 stepper driver
  1283. * 15000 : Maximum for TB6560 stepper driver
  1284. *
  1285. * Override the default value based on the driver type set in Configuration.h.
  1286. */
  1287. //#define MAXIMUM_STEPPER_RATE 250000
  1288. // @section temperature
  1289. // Control heater 0 and heater 1 in parallel.
  1290. //#define HEATERS_PARALLEL
  1291. //===========================================================================
  1292. //================================= Buffers =================================
  1293. //===========================================================================
  1294. // @section hidden
  1295. // The number of linear motions that can be in the plan at any give time.
  1296. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
  1297. #if ENABLED(SDSUPPORT)
  1298. #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
  1299. #else
  1300. #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
  1301. #endif
  1302. // @section serial
  1303. // The ASCII buffer for serial input
  1304. #define MAX_CMD_SIZE 96
  1305. #define BUFSIZE 4
  1306. // Transmission to Host Buffer Size
  1307. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  1308. // To buffer a simple "ok" you need 4 bytes.
  1309. // For ADVANCED_OK (M105) you need 32 bytes.
  1310. // For debug-echo: 128 bytes for the optimal speed.
  1311. // Other output doesn't need to be that speedy.
  1312. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  1313. #define TX_BUFFER_SIZE 0
  1314. // Host Receive Buffer Size
  1315. // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
  1316. // To use flow control, set this buffer size to at least 1024 bytes.
  1317. // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
  1318. //#define RX_BUFFER_SIZE 1024
  1319. #if RX_BUFFER_SIZE >= 1024
  1320. // Enable to have the controller send XON/XOFF control characters to
  1321. // the host to signal the RX buffer is becoming full.
  1322. //#define SERIAL_XON_XOFF
  1323. #endif
  1324. // Add M575 G-code to change the baud rate
  1325. //#define BAUD_RATE_GCODE
  1326. #if ENABLED(SDSUPPORT)
  1327. // Enable this option to collect and display the maximum
  1328. // RX queue usage after transferring a file to SD.
  1329. //#define SERIAL_STATS_MAX_RX_QUEUED
  1330. // Enable this option to collect and display the number
  1331. // of dropped bytes after a file transfer to SD.
  1332. //#define SERIAL_STATS_DROPPED_RX
  1333. #endif
  1334. // Enable an emergency-command parser to intercept certain commands as they
  1335. // enter the serial receive buffer, so they cannot be blocked.
  1336. // Currently handles M108, M112, M410
  1337. // Does not work on boards using AT90USB (USBCON) processors!
  1338. //#define EMERGENCY_PARSER
  1339. // Bad Serial-connections can miss a received command by sending an 'ok'
  1340. // Therefore some clients abort after 30 seconds in a timeout.
  1341. // Some other clients start sending commands while receiving a 'wait'.
  1342. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  1343. //#define NO_TIMEOUTS 1000 // Milliseconds
  1344. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  1345. //#define ADVANCED_OK
  1346. // Printrun may have trouble receiving long strings all at once.
  1347. // This option inserts short delays between lines of serial output.
  1348. #define SERIAL_OVERRUN_PROTECTION
  1349. // @section extras
  1350. /**
  1351. * Extra Fan Speed
  1352. * Adds a secondary fan speed for each print-cooling fan.
  1353. * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
  1354. * 'M106 P<fan> T2' : Use the set secondary speed
  1355. * 'M106 P<fan> T1' : Restore the previous fan speed
  1356. */
  1357. //#define EXTRA_FAN_SPEED
  1358. /**
  1359. * Firmware-based and LCD-controlled retract
  1360. *
  1361. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  1362. * Use M207 and M208 to define parameters for retract / recover.
  1363. *
  1364. * Use M209 to enable or disable auto-retract.
  1365. * With auto-retract enabled, all G1 E moves within the set range
  1366. * will be converted to firmware-based retract/recover moves.
  1367. *
  1368. * Be sure to turn off auto-retract during filament change.
  1369. *
  1370. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  1371. *
  1372. */
  1373. //#define FWRETRACT
  1374. #if ENABLED(FWRETRACT)
  1375. #define FWRETRACT_AUTORETRACT // Override slicer retractions
  1376. #if ENABLED(FWRETRACT_AUTORETRACT)
  1377. #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length
  1378. #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length
  1379. #endif
  1380. #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value)
  1381. #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
  1382. #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting
  1383. #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise
  1384. #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover)
  1385. #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
  1386. #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction
  1387. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction
  1388. #if ENABLED(MIXING_EXTRUDER)
  1389. //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously
  1390. #endif
  1391. #endif
  1392. /**
  1393. * Universal tool change settings.
  1394. * Applies to all types of extruders except where explicitly noted.
  1395. */
  1396. #if EXTRUDERS > 1
  1397. // Z raise distance for tool-change, as needed for some extruders
  1398. #define TOOLCHANGE_ZRAISE 2 // (mm)
  1399. //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change
  1400. // Retract and prime filament on tool-change
  1401. //#define TOOLCHANGE_FILAMENT_SWAP
  1402. #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
  1403. #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm)
  1404. #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm)
  1405. #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m)
  1406. #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m)
  1407. #endif
  1408. /**
  1409. * Position to park head during tool change.
  1410. * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
  1411. */
  1412. //#define TOOLCHANGE_PARK
  1413. #if ENABLED(TOOLCHANGE_PARK)
  1414. #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 }
  1415. #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m)
  1416. #endif
  1417. #endif
  1418. /**
  1419. * Advanced Pause
  1420. * Experimental feature for filament change support and for parking the nozzle when paused.
  1421. * Adds the GCode M600 for initiating filament change.
  1422. * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
  1423. *
  1424. * Requires an LCD display.
  1425. * Requires NOZZLE_PARK_FEATURE.
  1426. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  1427. */
  1428. //#define ADVANCED_PAUSE_FEATURE
  1429. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  1430. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
  1431. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
  1432. // This short retract is done immediately, before parking the nozzle.
  1433. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
  1434. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  1435. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
  1436. // For Bowden, the full length of the tube and nozzle.
  1437. // For direct drive, the full length of the nozzle.
  1438. // Set to 0 for manual unloading.
  1439. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
  1440. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
  1441. // 0 to disable start loading and skip to fast load only
  1442. #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
  1443. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  1444. #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
  1445. // For Bowden, the full length of the tube and nozzle.
  1446. // For direct drive, the full length of the nozzle.
  1447. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
  1448. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  1449. #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
  1450. // Set to 0 for manual extrusion.
  1451. // Filament can be extruded repeatedly from the Filament Change menu
  1452. // until extrusion is consistent, and to purge old filament.
  1453. #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
  1454. //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
  1455. // Filament Unload does a Retract, Delay, and Purge first:
  1456. #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
  1457. #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
  1458. #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
  1459. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
  1460. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
  1461. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
  1462. //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
  1463. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
  1464. //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  1465. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
  1466. #endif
  1467. // @section tmc
  1468. /**
  1469. * TMC26X Stepper Driver options
  1470. *
  1471. * The TMC26XStepper library is required for this stepper driver.
  1472. * https://github.com/trinamic/TMC26XStepper
  1473. */
  1474. #if HAS_DRIVER(TMC26X)
  1475. #if AXIS_DRIVER_TYPE_X(TMC26X)
  1476. #define X_MAX_CURRENT 1000 // (mA)
  1477. #define X_SENSE_RESISTOR 91 // (mOhms)
  1478. #define X_MICROSTEPS 16 // Number of microsteps
  1479. #endif
  1480. #if AXIS_DRIVER_TYPE_X2(TMC26X)
  1481. #define X2_MAX_CURRENT 1000
  1482. #define X2_SENSE_RESISTOR 91
  1483. #define X2_MICROSTEPS 16
  1484. #endif
  1485. #if AXIS_DRIVER_TYPE_Y(TMC26X)
  1486. #define Y_MAX_CURRENT 1000
  1487. #define Y_SENSE_RESISTOR 91
  1488. #define Y_MICROSTEPS 16
  1489. #endif
  1490. #if AXIS_DRIVER_TYPE_Y2(TMC26X)
  1491. #define Y2_MAX_CURRENT 1000
  1492. #define Y2_SENSE_RESISTOR 91
  1493. #define Y2_MICROSTEPS 16
  1494. #endif
  1495. #if AXIS_DRIVER_TYPE_Z(TMC26X)
  1496. #define Z_MAX_CURRENT 1000
  1497. #define Z_SENSE_RESISTOR 91
  1498. #define Z_MICROSTEPS 16
  1499. #endif
  1500. #if AXIS_DRIVER_TYPE_Z2(TMC26X)
  1501. #define Z2_MAX_CURRENT 1000
  1502. #define Z2_SENSE_RESISTOR 91
  1503. #define Z2_MICROSTEPS 16
  1504. #endif
  1505. #if AXIS_DRIVER_TYPE_Z3(TMC26X)
  1506. #define Z3_MAX_CURRENT 1000
  1507. #define Z3_SENSE_RESISTOR 91
  1508. #define Z3_MICROSTEPS 16
  1509. #endif
  1510. #if AXIS_DRIVER_TYPE_E0(TMC26X)
  1511. #define E0_MAX_CURRENT 1000
  1512. #define E0_SENSE_RESISTOR 91
  1513. #define E0_MICROSTEPS 16
  1514. #endif
  1515. #if AXIS_DRIVER_TYPE_E1(TMC26X)
  1516. #define E1_MAX_CURRENT 1000
  1517. #define E1_SENSE_RESISTOR 91
  1518. #define E1_MICROSTEPS 16
  1519. #endif
  1520. #if AXIS_DRIVER_TYPE_E2(TMC26X)
  1521. #define E2_MAX_CURRENT 1000
  1522. #define E2_SENSE_RESISTOR 91
  1523. #define E2_MICROSTEPS 16
  1524. #endif
  1525. #if AXIS_DRIVER_TYPE_E3(TMC26X)
  1526. #define E3_MAX_CURRENT 1000
  1527. #define E3_SENSE_RESISTOR 91
  1528. #define E3_MICROSTEPS 16
  1529. #endif
  1530. #if AXIS_DRIVER_TYPE_E4(TMC26X)
  1531. #define E4_MAX_CURRENT 1000
  1532. #define E4_SENSE_RESISTOR 91
  1533. #define E4_MICROSTEPS 16
  1534. #endif
  1535. #if AXIS_DRIVER_TYPE_E5(TMC26X)
  1536. #define E5_MAX_CURRENT 1000
  1537. #define E5_SENSE_RESISTOR 91
  1538. #define E5_MICROSTEPS 16
  1539. #endif
  1540. #endif // TMC26X
  1541. // @section tmc_smart
  1542. /**
  1543. * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode
  1544. * connect your SPI pins to the hardware SPI interface on your board and define
  1545. * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3
  1546. * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  1547. * You may also use software SPI if you wish to use general purpose IO pins.
  1548. *
  1549. * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN
  1550. * to the driver side PDN_UART pin with a 1K resistor.
  1551. * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without
  1552. * a resistor.
  1553. * The drivers can also be used with hardware serial.
  1554. *
  1555. * TMCStepper library is required to use TMC stepper drivers.
  1556. * https://github.com/teemuatlut/TMCStepper
  1557. */
  1558. #if HAS_TRINAMIC
  1559. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  1560. #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256
  1561. #if AXIS_IS_TMC(X)
  1562. #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current.
  1563. #define X_MICROSTEPS 16 // 0..256
  1564. #define X_RSENSE 0.11
  1565. #define X_CHAIN_POS -1 // <=0 : Not chained. 1 : MCU MOSI connected. 2 : Next in chain, ...
  1566. #endif
  1567. #if AXIS_IS_TMC(X2)
  1568. #define X2_CURRENT 800
  1569. #define X2_MICROSTEPS 16
  1570. #define X2_RSENSE 0.11
  1571. #define X2_CHAIN_POS -1
  1572. #endif
  1573. #if AXIS_IS_TMC(Y)
  1574. #define Y_CURRENT 800
  1575. #define Y_MICROSTEPS 16
  1576. #define Y_RSENSE 0.11
  1577. #define Y_CHAIN_POS -1
  1578. #endif
  1579. #if AXIS_IS_TMC(Y2)
  1580. #define Y2_CURRENT 800
  1581. #define Y2_MICROSTEPS 16
  1582. #define Y2_RSENSE 0.11
  1583. #define Y2_CHAIN_POS -1
  1584. #endif
  1585. #if AXIS_IS_TMC(Z)
  1586. #define Z_CURRENT 800
  1587. #define Z_MICROSTEPS 16
  1588. #define Z_RSENSE 0.11
  1589. #define Z_CHAIN_POS -1
  1590. #endif
  1591. #if AXIS_IS_TMC(Z2)
  1592. #define Z2_CURRENT 800
  1593. #define Z2_MICROSTEPS 16
  1594. #define Z2_RSENSE 0.11
  1595. #define Z2_CHAIN_POS -1
  1596. #endif
  1597. #if AXIS_IS_TMC(Z3)
  1598. #define Z3_CURRENT 800
  1599. #define Z3_MICROSTEPS 16
  1600. #define Z3_RSENSE 0.11
  1601. #define Z3_CHAIN_POS -1
  1602. #endif
  1603. #if AXIS_IS_TMC(E0)
  1604. #define E0_CURRENT 800
  1605. #define E0_MICROSTEPS 16
  1606. #define E0_RSENSE 0.11
  1607. #define E0_CHAIN_POS -1
  1608. #endif
  1609. #if AXIS_IS_TMC(E1)
  1610. #define E1_CURRENT 800
  1611. #define E1_MICROSTEPS 16
  1612. #define E1_RSENSE 0.11
  1613. #define E1_CHAIN_POS -1
  1614. #endif
  1615. #if AXIS_IS_TMC(E2)
  1616. #define E2_CURRENT 800
  1617. #define E2_MICROSTEPS 16
  1618. #define E2_RSENSE 0.11
  1619. #define E2_CHAIN_POS -1
  1620. #endif
  1621. #if AXIS_IS_TMC(E3)
  1622. #define E3_CURRENT 800
  1623. #define E3_MICROSTEPS 16
  1624. #define E3_RSENSE 0.11
  1625. #define E3_CHAIN_POS -1
  1626. #endif
  1627. #if AXIS_IS_TMC(E4)
  1628. #define E4_CURRENT 800
  1629. #define E4_MICROSTEPS 16
  1630. #define E4_RSENSE 0.11
  1631. #define E4_CHAIN_POS -1
  1632. #endif
  1633. #if AXIS_IS_TMC(E5)
  1634. #define E5_CURRENT 800
  1635. #define E5_MICROSTEPS 16
  1636. #define E5_RSENSE 0.11
  1637. #define E5_CHAIN_POS -1
  1638. #endif
  1639. /**
  1640. * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here.
  1641. * The default pins can be found in your board's pins file.
  1642. */
  1643. //#define X_CS_PIN -1
  1644. //#define Y_CS_PIN -1
  1645. //#define Z_CS_PIN -1
  1646. //#define X2_CS_PIN -1
  1647. //#define Y2_CS_PIN -1
  1648. //#define Z2_CS_PIN -1
  1649. //#define Z3_CS_PIN -1
  1650. //#define E0_CS_PIN -1
  1651. //#define E1_CS_PIN -1
  1652. //#define E2_CS_PIN -1
  1653. //#define E3_CS_PIN -1
  1654. //#define E4_CS_PIN -1
  1655. //#define E5_CS_PIN -1
  1656. /**
  1657. * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
  1658. * The default SW SPI pins are defined the respective pins files,
  1659. * but you can override or define them here.
  1660. */
  1661. //#define TMC_USE_SW_SPI
  1662. //#define TMC_SW_MOSI -1
  1663. //#define TMC_SW_MISO -1
  1664. //#define TMC_SW_SCK -1
  1665. /**
  1666. * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses.
  1667. * Set the address using jumpers on pins MS1 and MS2.
  1668. * Address | MS1 | MS2
  1669. * 0 | LOW | LOW
  1670. * 1 | HIGH | LOW
  1671. * 2 | LOW | HIGH
  1672. * 3 | HIGH | HIGH
  1673. *
  1674. * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers
  1675. * on the same serial port, either here or in your board's pins file.
  1676. */
  1677. #define X_SLAVE_ADDRESS 0
  1678. #define Y_SLAVE_ADDRESS 0
  1679. #define Z_SLAVE_ADDRESS 0
  1680. #define X2_SLAVE_ADDRESS 0
  1681. #define Y2_SLAVE_ADDRESS 0
  1682. #define Z2_SLAVE_ADDRESS 0
  1683. #define Z3_SLAVE_ADDRESS 0
  1684. #define E0_SLAVE_ADDRESS 0
  1685. #define E1_SLAVE_ADDRESS 0
  1686. #define E2_SLAVE_ADDRESS 0
  1687. #define E3_SLAVE_ADDRESS 0
  1688. #define E4_SLAVE_ADDRESS 0
  1689. #define E5_SLAVE_ADDRESS 0
  1690. /**
  1691. * Software enable
  1692. *
  1693. * Use for drivers that do not use a dedicated enable pin, but rather handle the same
  1694. * function through a communication line such as SPI or UART.
  1695. */
  1696. //#define SOFTWARE_DRIVER_ENABLE
  1697. /**
  1698. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  1699. * Use Trinamic's ultra quiet stepping mode.
  1700. * When disabled, Marlin will use spreadCycle stepping mode.
  1701. */
  1702. #define STEALTHCHOP_XY
  1703. #define STEALTHCHOP_Z
  1704. #define STEALTHCHOP_E
  1705. /**
  1706. * Optimize spreadCycle chopper parameters by using predefined parameter sets
  1707. * or with the help of an example included in the library.
  1708. * Provided parameter sets are
  1709. * CHOPPER_DEFAULT_12V
  1710. * CHOPPER_DEFAULT_19V
  1711. * CHOPPER_DEFAULT_24V
  1712. * CHOPPER_DEFAULT_36V
  1713. * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V)
  1714. * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9
  1715. *
  1716. * Define you own with
  1717. * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
  1718. */
  1719. #define CHOPPER_TIMING CHOPPER_DEFAULT_12V
  1720. /**
  1721. * Monitor Trinamic drivers for error conditions,
  1722. * like overtemperature and short to ground.
  1723. * In the case of overtemperature Marlin can decrease the driver current until error condition clears.
  1724. * Other detected conditions can be used to stop the current print.
  1725. * Relevant g-codes:
  1726. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  1727. * M911 - Report stepper driver overtemperature pre-warn condition.
  1728. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  1729. * M122 - Report driver parameters (Requires TMC_DEBUG)
  1730. */
  1731. //#define MONITOR_DRIVER_STATUS
  1732. #if ENABLED(MONITOR_DRIVER_STATUS)
  1733. #define CURRENT_STEP_DOWN 50 // [mA]
  1734. #define REPORT_CURRENT_CHANGE
  1735. #define STOP_ON_ERROR
  1736. #endif
  1737. /**
  1738. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  1739. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  1740. * This mode allows for faster movements at the expense of higher noise levels.
  1741. * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
  1742. * M913 X/Y/Z/E to live tune the setting
  1743. */
  1744. //#define HYBRID_THRESHOLD
  1745. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  1746. #define X2_HYBRID_THRESHOLD 100
  1747. #define Y_HYBRID_THRESHOLD 100
  1748. #define Y2_HYBRID_THRESHOLD 100
  1749. #define Z_HYBRID_THRESHOLD 3
  1750. #define Z2_HYBRID_THRESHOLD 3
  1751. #define Z3_HYBRID_THRESHOLD 3
  1752. #define E0_HYBRID_THRESHOLD 30
  1753. #define E1_HYBRID_THRESHOLD 30
  1754. #define E2_HYBRID_THRESHOLD 30
  1755. #define E3_HYBRID_THRESHOLD 30
  1756. #define E4_HYBRID_THRESHOLD 30
  1757. #define E5_HYBRID_THRESHOLD 30
  1758. /**
  1759. * Use StallGuard2 to home / probe X, Y, Z.
  1760. *
  1761. * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
  1762. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
  1763. * X, Y, and Z homing will always be done in spreadCycle mode.
  1764. *
  1765. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
  1766. * Use M914 X Y Z to set the stall threshold at runtime:
  1767. *
  1768. * Sensitivity TMC2209 Others
  1769. * HIGHEST 255 -64 (Too sensitive => False positive)
  1770. * LOWEST 0 63 (Too insensitive => No trigger)
  1771. *
  1772. * It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
  1773. *
  1774. * SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only ***
  1775. * Poll the driver through SPI to determine load when homing.
  1776. * Removes the need for a wire from DIAG1 to an endstop pin.
  1777. *
  1778. * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
  1779. * homing and adds a guard period for endstop triggering.
  1780. */
  1781. //#define SENSORLESS_HOMING // StallGuard capable drivers only
  1782. /**
  1783. * Use StallGuard2 to probe the bed with the nozzle.
  1784. *
  1785. * CAUTION: This could cause damage to machines that use a lead screw or threaded rod
  1786. * to move the Z axis. Take extreme care when attempting to enable this feature.
  1787. */
  1788. //#define SENSORLESS_PROBING // StallGuard capable drivers only
  1789. #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
  1790. // TMC2209: 0...255. TMC2130: -64...63
  1791. #define X_STALL_SENSITIVITY 8
  1792. #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
  1793. #define Y_STALL_SENSITIVITY 8
  1794. //#define Z_STALL_SENSITIVITY 8
  1795. //#define SPI_ENDSTOPS // TMC2130 only
  1796. //#define IMPROVE_HOMING_RELIABILITY
  1797. #endif
  1798. /**
  1799. * Beta feature!
  1800. * Create a 50/50 square wave step pulse optimal for stepper drivers.
  1801. */
  1802. //#define SQUARE_WAVE_STEPPING
  1803. /**
  1804. * Enable M122 debugging command for TMC stepper drivers.
  1805. * M122 S0/1 will enable continous reporting.
  1806. */
  1807. //#define TMC_DEBUG
  1808. /**
  1809. * You can set your own advanced settings by filling in predefined functions.
  1810. * A list of available functions can be found on the library github page
  1811. * https://github.com/teemuatlut/TMCStepper
  1812. *
  1813. * Example:
  1814. * #define TMC_ADV() { \
  1815. * stepperX.diag0_temp_prewarn(1); \
  1816. * stepperY.interpolate(0); \
  1817. * }
  1818. */
  1819. #define TMC_ADV() { }
  1820. #endif // HAS_TRINAMIC
  1821. // @section L6470
  1822. /**
  1823. * L6470 Stepper Driver options
  1824. *
  1825. * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver.
  1826. * https://github.com/ameyer/Arduino-L6470
  1827. *
  1828. * Requires the following to be defined in your pins_YOUR_BOARD file
  1829. * L6470_CHAIN_SCK_PIN
  1830. * L6470_CHAIN_MISO_PIN
  1831. * L6470_CHAIN_MOSI_PIN
  1832. * L6470_CHAIN_SS_PIN
  1833. * L6470_RESET_CHAIN_PIN (optional)
  1834. */
  1835. #if HAS_DRIVER(L6470)
  1836. //#define L6470_CHITCHAT // Display additional status info
  1837. #if AXIS_DRIVER_TYPE_X(L6470)
  1838. #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128)
  1839. #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down)
  1840. #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down)
  1841. #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper
  1842. #define X_CHAIN_POS -1 // Position in SPI chain. (<=0 : Not in chain. 1 : Nearest MOSI)
  1843. #endif
  1844. #if AXIS_DRIVER_TYPE_X2(L6470)
  1845. #define X2_MICROSTEPS 128
  1846. #define X2_OVERCURRENT 2000
  1847. #define X2_STALLCURRENT 1500
  1848. #define X2_MAX_VOLTAGE 127
  1849. #define X2_CHAIN_POS -1
  1850. #endif
  1851. #if AXIS_DRIVER_TYPE_Y(L6470)
  1852. #define Y_MICROSTEPS 128
  1853. #define Y_OVERCURRENT 2000
  1854. #define Y_STALLCURRENT 1500
  1855. #define Y_MAX_VOLTAGE 127
  1856. #define Y_CHAIN_POS -1
  1857. #endif
  1858. #if AXIS_DRIVER_TYPE_Y2(L6470)
  1859. #define Y2_MICROSTEPS 128
  1860. #define Y2_OVERCURRENT 2000
  1861. #define Y2_STALLCURRENT 1500
  1862. #define Y2_MAX_VOLTAGE 127
  1863. #define Y2_CHAIN_POS -1
  1864. #endif
  1865. #if AXIS_DRIVER_TYPE_Z(L6470)
  1866. #define Z_MICROSTEPS 128
  1867. #define Z_OVERCURRENT 2000
  1868. #define Z_STALLCURRENT 1500
  1869. #define Z_MAX_VOLTAGE 127
  1870. #define Z_CHAIN_POS -1
  1871. #endif
  1872. #if AXIS_DRIVER_TYPE_Z2(L6470)
  1873. #define Z2_MICROSTEPS 128
  1874. #define Z2_OVERCURRENT 2000
  1875. #define Z2_STALLCURRENT 1500
  1876. #define Z2_MAX_VOLTAGE 127
  1877. #define Z2_CHAIN_POS -1
  1878. #endif
  1879. #if AXIS_DRIVER_TYPE_Z3(L6470)
  1880. #define Z3_MICROSTEPS 128
  1881. #define Z3_OVERCURRENT 2000
  1882. #define Z3_STALLCURRENT 1500
  1883. #define Z3_MAX_VOLTAGE 127
  1884. #define Z3_CHAIN_POS -1
  1885. #endif
  1886. #if AXIS_DRIVER_TYPE_E0(L6470)
  1887. #define E0_MICROSTEPS 128
  1888. #define E0_OVERCURRENT 2000
  1889. #define E0_STALLCURRENT 1500
  1890. #define E0_MAX_VOLTAGE 127
  1891. #define E0_CHAIN_POS -1
  1892. #endif
  1893. #if AXIS_DRIVER_TYPE_E1(L6470)
  1894. #define E1_MICROSTEPS 128
  1895. #define E1_OVERCURRENT 2000
  1896. #define E1_STALLCURRENT 1500
  1897. #define E1_MAX_VOLTAGE 127
  1898. #define E1_CHAIN_POS -1
  1899. #endif
  1900. #if AXIS_DRIVER_TYPE_E2(L6470)
  1901. #define E2_MICROSTEPS 128
  1902. #define E2_OVERCURRENT 2000
  1903. #define E2_STALLCURRENT 1500
  1904. #define E2_MAX_VOLTAGE 127
  1905. #define E2_CHAIN_POS -1
  1906. #endif
  1907. #if AXIS_DRIVER_TYPE_E3(L6470)
  1908. #define E3_MICROSTEPS 128
  1909. #define E3_OVERCURRENT 2000
  1910. #define E3_STALLCURRENT 1500
  1911. #define E3_MAX_VOLTAGE 127
  1912. #define E3_CHAIN_POS -1
  1913. #endif
  1914. #if AXIS_DRIVER_TYPE_E4(L6470)
  1915. #define E4_MICROSTEPS 128
  1916. #define E4_OVERCURRENT 2000
  1917. #define E4_STALLCURRENT 1500
  1918. #define E4_MAX_VOLTAGE 127
  1919. #define E4_CHAIN_POS -1
  1920. #endif
  1921. #if AXIS_DRIVER_TYPE_E5(L6470)
  1922. #define E5_MICROSTEPS 128
  1923. #define E5_OVERCURRENT 2000
  1924. #define E5_STALLCURRENT 1500
  1925. #define E5_MAX_VOLTAGE 127
  1926. #define E5_CHAIN_POS -1
  1927. #endif
  1928. /**
  1929. * Monitor L6470 drivers for error conditions like over temperature and over current.
  1930. * In the case of over temperature Marlin can decrease the drive until the error condition clears.
  1931. * Other detected conditions can be used to stop the current print.
  1932. * Relevant g-codes:
  1933. * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given.
  1934. * I not present or I0 or I1 - X, Y, Z or E0
  1935. * I2 - X2, Y2, Z2 or E1
  1936. * I3 - Z3 or E3
  1937. * I4 - E4
  1938. * I5 - E5
  1939. * M916 - Increase drive level until get thermal warning
  1940. * M917 - Find minimum current thresholds
  1941. * M918 - Increase speed until max or error
  1942. * M122 S0/1 - Report driver parameters
  1943. */
  1944. //#define MONITOR_L6470_DRIVER_STATUS
  1945. #if ENABLED(MONITOR_L6470_DRIVER_STATUS)
  1946. #define KVAL_HOLD_STEP_DOWN 1
  1947. //#define L6470_STOP_ON_ERROR
  1948. #endif
  1949. #endif // L6470
  1950. /**
  1951. * TWI/I2C BUS
  1952. *
  1953. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  1954. * machines. Enabling this will allow you to send and receive I2C data from slave
  1955. * devices on the bus.
  1956. *
  1957. * ; Example #1
  1958. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  1959. * ; It uses multiple M260 commands with one B<base 10> arg
  1960. * M260 A99 ; Target slave address
  1961. * M260 B77 ; M
  1962. * M260 B97 ; a
  1963. * M260 B114 ; r
  1964. * M260 B108 ; l
  1965. * M260 B105 ; i
  1966. * M260 B110 ; n
  1967. * M260 S1 ; Send the current buffer
  1968. *
  1969. * ; Example #2
  1970. * ; Request 6 bytes from slave device with address 0x63 (99)
  1971. * M261 A99 B5
  1972. *
  1973. * ; Example #3
  1974. * ; Example serial output of a M261 request
  1975. * echo:i2c-reply: from:99 bytes:5 data:hello
  1976. */
  1977. // @section i2cbus
  1978. //#define EXPERIMENTAL_I2CBUS
  1979. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  1980. // @section extras
  1981. /**
  1982. * Photo G-code
  1983. * Add the M240 G-code to take a photo.
  1984. * The photo can be triggered by a digital pin or a physical movement.
  1985. */
  1986. //#define PHOTO_GCODE
  1987. #if ENABLED(PHOTO_GCODE)
  1988. // A position to move to (and raise Z) before taking the photo
  1989. //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z)
  1990. //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P)
  1991. //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S)
  1992. // Canon RC-1 or homebrew digital camera trigger
  1993. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1994. //#define PHOTOGRAPH_PIN 23
  1995. // Canon Hack Development Kit
  1996. // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  1997. //#define CHDK_PIN 4
  1998. // Optional second move with delay to trigger the camera shutter
  1999. //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J)
  2000. // Duration to hold the switch or keep CHDK_PIN high
  2001. //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)
  2002. #endif
  2003. /**
  2004. * Spindle & Laser control
  2005. *
  2006. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  2007. * to set spindle speed, spindle direction, and laser power.
  2008. *
  2009. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  2010. * Marlin can be used to turn the spindle on and off. It can also be used to set
  2011. * the spindle speed from 5,000 to 30,000 RPM.
  2012. *
  2013. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  2014. * hardware PWM pin for the speed control and a pin for the rotation direction.
  2015. *
  2016. * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  2017. */
  2018. //#define SPINDLE_FEATURE
  2019. //#define LASER_FEATURE
  2020. #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
  2021. #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
  2022. #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
  2023. #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
  2024. #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
  2025. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
  2026. #if ENABLED(SPINDLE_FEATURE)
  2027. //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
  2028. #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
  2029. #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
  2030. /**
  2031. * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
  2032. *
  2033. * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
  2034. * where PWM duty cycle varies from 0 to 255
  2035. *
  2036. * set the following for your controller (ALL MUST BE SET)
  2037. */
  2038. #define SPEED_POWER_SLOPE 118.4
  2039. #define SPEED_POWER_INTERCEPT 0
  2040. #define SPEED_POWER_MIN 5000
  2041. #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
  2042. #else
  2043. #define SPEED_POWER_SLOPE 0.3922
  2044. #define SPEED_POWER_INTERCEPT 0
  2045. #define SPEED_POWER_MIN 10
  2046. #define SPEED_POWER_MAX 100 // 0-100%
  2047. #endif
  2048. #endif
  2049. /**
  2050. * Coolant Control
  2051. *
  2052. * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off.
  2053. *
  2054. * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined.
  2055. */
  2056. //#define COOLANT_CONTROL
  2057. #if ENABLED(COOLANT_CONTROL)
  2058. #define COOLANT_MIST // Enable if mist coolant is present
  2059. #define COOLANT_FLOOD // Enable if flood coolant is present
  2060. #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed
  2061. #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
  2062. #endif
  2063. /**
  2064. * Filament Width Sensor
  2065. *
  2066. * Measures the filament width in real-time and adjusts
  2067. * flow rate to compensate for any irregularities.
  2068. *
  2069. * Also allows the measured filament diameter to set the
  2070. * extrusion rate, so the slicer only has to specify the
  2071. * volume.
  2072. *
  2073. * Only a single extruder is supported at this time.
  2074. *
  2075. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  2076. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  2077. * 301 RAMBO : Analog input 3
  2078. *
  2079. * Note: May require analog pins to be defined for other boards.
  2080. */
  2081. //#define FILAMENT_WIDTH_SENSOR
  2082. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  2083. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
  2084. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  2085. #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
  2086. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  2087. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  2088. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  2089. //#define FILAMENT_LCD_DISPLAY
  2090. #endif
  2091. /**
  2092. * CNC Coordinate Systems
  2093. *
  2094. * Enables G53 and G54-G59.3 commands to select coordinate systems
  2095. * and G92.1 to reset the workspace to native machine space.
  2096. */
  2097. //#define CNC_COORDINATE_SYSTEMS
  2098. /**
  2099. * Auto-report temperatures with M155 S<seconds>
  2100. */
  2101. #define AUTO_REPORT_TEMPERATURES
  2102. /**
  2103. * Include capabilities in M115 output
  2104. */
  2105. #define EXTENDED_CAPABILITIES_REPORT
  2106. /**
  2107. * Expected Printer Check
  2108. * Add the M16 G-code to compare a string to the MACHINE_NAME.
  2109. * M16 with a non-matching string causes the printer to halt.
  2110. */
  2111. //#define EXPECTED_PRINTER_CHECK
  2112. /**
  2113. * Disable all Volumetric extrusion options
  2114. */
  2115. //#define NO_VOLUMETRICS
  2116. #if DISABLED(NO_VOLUMETRICS)
  2117. /**
  2118. * Volumetric extrusion default state
  2119. * Activate to make volumetric extrusion the default method,
  2120. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  2121. *
  2122. * M200 D0 to disable, M200 Dn to set a new diameter.
  2123. */
  2124. //#define VOLUMETRIC_DEFAULT_ON
  2125. #endif
  2126. /**
  2127. * Enable this option for a leaner build of Marlin that removes all
  2128. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  2129. *
  2130. * - M206 and M428 are disabled.
  2131. * - G92 will revert to its behavior from Marlin 1.0.
  2132. */
  2133. //#define NO_WORKSPACE_OFFSETS
  2134. /**
  2135. * Set the number of proportional font spaces required to fill up a typical character space.
  2136. * This can help to better align the output of commands like `G29 O` Mesh Output.
  2137. *
  2138. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  2139. * Otherwise, adjust according to your client and font.
  2140. */
  2141. #define PROPORTIONAL_FONT_RATIO 1.0
  2142. /**
  2143. * Spend 28 bytes of SRAM to optimize the GCode parser
  2144. */
  2145. #define FASTER_GCODE_PARSER
  2146. /**
  2147. * CNC G-code options
  2148. * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
  2149. * Note that G0 feedrates should be used with care for 3D printing (if used at all).
  2150. * High feedrates may cause ringing and harm print quality.
  2151. */
  2152. //#define PAREN_COMMENTS // Support for parentheses-delimited comments
  2153. //#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
  2154. // Enable and set a (default) feedrate for all G0 moves
  2155. //#define G0_FEEDRATE 3000 // (mm/m)
  2156. #ifdef G0_FEEDRATE
  2157. //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
  2158. #endif
  2159. /**
  2160. * Startup commands
  2161. *
  2162. * Execute certain G-code commands immediately after power-on.
  2163. */
  2164. //#define STARTUP_COMMANDS "M17 Z"
  2165. /**
  2166. * G-code Macros
  2167. *
  2168. * Add G-codes M810-M819 to define and run G-code macros.
  2169. * Macros are not saved to EEPROM.
  2170. */
  2171. //#define GCODE_MACROS
  2172. #if ENABLED(GCODE_MACROS)
  2173. #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used
  2174. #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro
  2175. #endif
  2176. /**
  2177. * User-defined menu items that execute custom GCode
  2178. */
  2179. //#define CUSTOM_USER_MENUS
  2180. #if ENABLED(CUSTOM_USER_MENUS)
  2181. //#define CUSTOM_USER_MENU_TITLE "Custom Commands"
  2182. #define USER_SCRIPT_DONE "M117 User Script Done"
  2183. #define USER_SCRIPT_AUDIBLE_FEEDBACK
  2184. //#define USER_SCRIPT_RETURN // Return to status screen after a script
  2185. #define USER_DESC_1 "Home & UBL Info"
  2186. #define USER_GCODE_1 "G28\nG29 W"
  2187. #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
  2188. #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  2189. #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
  2190. #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  2191. #define USER_DESC_4 "Heat Bed/Home/Level"
  2192. #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  2193. #define USER_DESC_5 "Home & Info"
  2194. #define USER_GCODE_5 "G28\nM503"
  2195. #endif
  2196. /**
  2197. * Host Action Commands
  2198. *
  2199. * Define host streamer action commands in compliance with the standard.
  2200. *
  2201. * See https://reprap.org/wiki/G-code#Action_commands
  2202. * Common commands ........ poweroff, pause, paused, resume, resumed, cancel
  2203. * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed
  2204. *
  2205. * Some features add reason codes to extend these commands.
  2206. *
  2207. * Host Prompt Support enables Marlin to use the host for user prompts so
  2208. * filament runout and other processes can be managed from the host side.
  2209. */
  2210. //#define HOST_ACTION_COMMANDS
  2211. #if ENABLED(HOST_ACTION_COMMANDS)
  2212. //#define HOST_PROMPT_SUPPORT
  2213. #endif
  2214. /**
  2215. * I2C position encoders for closed loop control.
  2216. * Developed by Chris Barr at Aus3D.
  2217. *
  2218. * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
  2219. * Github: https://github.com/Aus3D/MagneticEncoder
  2220. *
  2221. * Supplier: http://aus3d.com.au/magnetic-encoder-module
  2222. * Alternative Supplier: http://reliabuild3d.com/
  2223. *
  2224. * Reliabuild encoders have been modified to improve reliability.
  2225. */
  2226. //#define I2C_POSITION_ENCODERS
  2227. #if ENABLED(I2C_POSITION_ENCODERS)
  2228. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  2229. // encoders supported currently.
  2230. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  2231. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  2232. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  2233. // I2CPE_ENC_TYPE_ROTARY.
  2234. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  2235. // 1mm poles. For linear encoders this is ticks / mm,
  2236. // for rotary encoders this is ticks / revolution.
  2237. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  2238. // steps per full revolution (motor steps/rev * microstepping)
  2239. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  2240. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
  2241. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  2242. // printer will attempt to correct the error; errors
  2243. // smaller than this are ignored to minimize effects of
  2244. // measurement noise / latency (filter).
  2245. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  2246. #define I2CPE_ENC_2_AXIS Y_AXIS
  2247. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  2248. #define I2CPE_ENC_2_TICKS_UNIT 2048
  2249. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  2250. //#define I2CPE_ENC_2_INVERT
  2251. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
  2252. #define I2CPE_ENC_2_EC_THRESH 0.10
  2253. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  2254. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  2255. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  2256. #define I2CPE_ENC_4_AXIS E_AXIS
  2257. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  2258. #define I2CPE_ENC_5_AXIS E_AXIS
  2259. // Default settings for encoders which are enabled, but without settings configured above.
  2260. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  2261. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  2262. #define I2CPE_DEF_TICKS_REV (16 * 200)
  2263. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  2264. #define I2CPE_DEF_EC_THRESH 0.1
  2265. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  2266. // axis after which the printer will abort. Comment out to
  2267. // disable abort behavior.
  2268. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  2269. // for this amount of time (in ms) before the encoder
  2270. // is trusted again.
  2271. /**
  2272. * Position is checked every time a new command is executed from the buffer but during long moves,
  2273. * this setting determines the minimum update time between checks. A value of 100 works well with
  2274. * error rolling average when attempting to correct only for skips and not for vibration.
  2275. */
  2276. #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
  2277. // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
  2278. #define I2CPE_ERR_ROLLING_AVERAGE
  2279. #endif // I2C_POSITION_ENCODERS
  2280. /**
  2281. * Analog Joystick(s)
  2282. */
  2283. //#define JOYSTICK
  2284. #if ENABLED(JOYSTICK)
  2285. #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2
  2286. #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2
  2287. #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
  2288. #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
  2289. // Use M119 to find reasonable values after connecting your hardware:
  2290. #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
  2291. #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
  2292. #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
  2293. #endif
  2294. /**
  2295. * MAX7219 Debug Matrix
  2296. *
  2297. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
  2298. * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  2299. */
  2300. //#define MAX7219_DEBUG
  2301. #if ENABLED(MAX7219_DEBUG)
  2302. #define MAX7219_CLK_PIN 64
  2303. #define MAX7219_DIN_PIN 57
  2304. #define MAX7219_LOAD_PIN 44
  2305. //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix
  2306. #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral)
  2307. #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain.
  2308. #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°)
  2309. // connector at: right=0 bottom=-90 top=90 left=180
  2310. //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order
  2311. //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side
  2312. /**
  2313. * Sample debug features
  2314. * If you add more debug displays, be careful to avoid conflicts!
  2315. */
  2316. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  2317. #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row
  2318. #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row
  2319. #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row
  2320. // If you experience stuttering, reboots, etc. this option can reveal how
  2321. // tweaks made to the configuration are affecting the printer in real-time.
  2322. #endif
  2323. /**
  2324. * NanoDLP Sync support
  2325. *
  2326. * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp"
  2327. * string to enable synchronization with DLP projector exposure. This change will allow to use
  2328. * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  2329. */
  2330. //#define NANODLP_Z_SYNC
  2331. #if ENABLED(NANODLP_Z_SYNC)
  2332. //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
  2333. // Default behavior is limited to Z axis only.
  2334. #endif
  2335. /**
  2336. * WiFi Support (Espressif ESP32 WiFi)
  2337. */
  2338. //#define WIFISUPPORT
  2339. #if ENABLED(WIFISUPPORT)
  2340. #define WIFI_SSID "Wifi SSID"
  2341. #define WIFI_PWD "Wifi Password"
  2342. //#define WEBSUPPORT // Start a webserver with auto-discovery
  2343. //#define OTASUPPORT // Support over-the-air firmware updates
  2344. #endif
  2345. /**
  2346. * Prusa Multi-Material Unit v2
  2347. * Enable in Configuration.h
  2348. */
  2349. #if ENABLED(PRUSA_MMU2)
  2350. // Serial port used for communication with MMU2.
  2351. // For AVR enable the UART port used for the MMU. (e.g., internalSerial)
  2352. // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2)
  2353. #define INTERNAL_SERIAL_PORT 2
  2354. #define MMU2_SERIAL internalSerial
  2355. // Use hardware reset for MMU if a pin is defined for it
  2356. //#define MMU2_RST_PIN 23
  2357. // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up)
  2358. //#define MMU2_MODE_12V
  2359. // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout
  2360. #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600"
  2361. // Add an LCD menu for MMU2
  2362. //#define MMU2_MENUS
  2363. #if ENABLED(MMU2_MENUS)
  2364. // Settings for filament load / unload from the LCD menu.
  2365. // This is for Prusa MK3-style extruders. Customize for your hardware.
  2366. #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0
  2367. #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \
  2368. { 7.2, 562 }, \
  2369. { 14.4, 871 }, \
  2370. { 36.0, 1393 }, \
  2371. { 14.4, 871 }, \
  2372. { 50.0, 198 }
  2373. #define MMU2_RAMMING_SEQUENCE \
  2374. { 1.0, 1000 }, \
  2375. { 1.0, 1500 }, \
  2376. { 2.0, 2000 }, \
  2377. { 1.5, 3000 }, \
  2378. { 2.5, 4000 }, \
  2379. { -15.0, 5000 }, \
  2380. { -14.0, 1200 }, \
  2381. { -6.0, 600 }, \
  2382. { 10.0, 700 }, \
  2383. { -10.0, 400 }, \
  2384. { -50.0, 2000 }
  2385. #endif
  2386. //#define MMU2_DEBUG // Write debug info to serial output
  2387. #endif // PRUSA_MMU2
  2388. /**
  2389. * Advanced Print Counter settings
  2390. */
  2391. #if ENABLED(PRINTCOUNTER)
  2392. #define SERVICE_WARNING_BUZZES 3
  2393. // Activate up to 3 service interval watchdogs
  2394. //#define SERVICE_NAME_1 "Service S"
  2395. //#define SERVICE_INTERVAL_1 100 // print hours
  2396. //#define SERVICE_NAME_2 "Service L"
  2397. //#define SERVICE_INTERVAL_2 200 // print hours
  2398. //#define SERVICE_NAME_3 "Service 3"
  2399. //#define SERVICE_INTERVAL_3 1 // print hours
  2400. #endif
  2401. // @section develop
  2402. /**
  2403. * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
  2404. */
  2405. //#define PINS_DEBUGGING
  2406. // Enable Marlin dev mode which adds some special commands
  2407. //#define MARLIN_DEV_MODE