My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 40KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839
  1. #ifndef CONFIGURATION_H
  2. #define CONFIGURATION_H
  3. #include "boards.h"
  4. #include "macros.h"
  5. //===========================================================================
  6. //============================= Getting Started =============================
  7. //===========================================================================
  8. /*
  9. Here are some standard links for getting your machine calibrated:
  10. * http://reprap.org/wiki/Calibration
  11. * http://youtu.be/wAL9d7FgInk
  12. * http://calculator.josefprusa.cz
  13. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  14. * http://www.thingiverse.com/thing:5573
  15. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  16. * http://www.thingiverse.com/thing:298812
  17. */
  18. // This configuration file contains the basic settings.
  19. // Advanced settings can be found in Configuration_adv.h
  20. // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
  21. //===========================================================================
  22. //============================= DELTA Printer ===============================
  23. //===========================================================================
  24. // For a Delta printer replace the configuration files with the files in the
  25. // example_configurations/delta directory.
  26. //
  27. //===========================================================================
  28. //============================= SCARA Printer ===============================
  29. //===========================================================================
  30. // For a Scara printer replace the configuration files with the files in the
  31. // example_configurations/SCARA directory.
  32. //
  33. // @section info
  34. #if ENABLED(USE_AUTOMATIC_VERSIONING)
  35. #include "_Version.h"
  36. #else
  37. #include "Default_Version.h"
  38. #endif
  39. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  40. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  41. // build by the user have been successfully uploaded into firmware.
  42. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  43. #define SHOW_BOOTSCREEN
  44. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  45. //#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
  46. // @section machine
  47. // SERIAL_PORT selects which serial port should be used for communication with the host.
  48. // This allows the connection of wireless adapters (for instance) to non-default port pins.
  49. // Serial port 0 is still used by the Arduino bootloader regardless of this setting.
  50. // :[0,1,2,3,4,5,6,7]
  51. #define SERIAL_PORT 0
  52. // This determines the communication speed of the printer
  53. // :[2400,9600,19200,38400,57600,115200,250000]
  54. #define BAUDRATE 250000
  55. // Enable the Bluetooth serial interface on AT90USB devices
  56. //#define BLUETOOTH
  57. // The following define selects which electronics board you have.
  58. // Please choose the name from boards.h that matches your setup
  59. #ifndef MOTHERBOARD
  60. #define MOTHERBOARD BOARD_FELIX2
  61. #endif
  62. // Optional custom name for your RepStrap or other custom machine
  63. // Displayed in the LCD "Ready" message
  64. #define CUSTOM_MACHINE_NAME "Felix"
  65. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  66. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  67. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  68. // This defines the number of extruders
  69. // :[1,2,3,4]
  70. #define EXTRUDERS 1
  71. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  72. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  73. // For the other hotends it is their distance from the extruder 0 hotend.
  74. //#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  75. //#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  76. //// The following define selects which power supply you have. Please choose the one that matches your setup
  77. // 1 = ATX
  78. // 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  79. // :{1:'ATX',2:'X-Box 360'}
  80. #define POWER_SUPPLY 1
  81. // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
  82. #define PS_DEFAULT_OFF
  83. // @section temperature
  84. //===========================================================================
  85. //============================= Thermal Settings ============================
  86. //===========================================================================
  87. //
  88. //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  89. //
  90. //// Temperature sensor settings:
  91. // -2 is thermocouple with MAX6675 (only for sensor 0)
  92. // -1 is thermocouple with AD595
  93. // 0 is not used
  94. // 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  95. // 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  96. // 3 is Mendel-parts thermistor (4.7k pullup)
  97. // 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  98. // 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  99. // 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  100. // 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  101. // 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  102. // 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  103. // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  104. // 10 is 100k RS thermistor 198-961 (4.7k pullup)
  105. // 11 is 100k beta 3950 1% thermistor (4.7k pullup)
  106. // 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  107. // 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  108. // 20 is the PT100 circuit found in the Ultimainboard V2.x
  109. // 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  110. //
  111. // 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
  112. // (but gives greater accuracy and more stable PID)
  113. // 51 is 100k thermistor - EPCOS (1k pullup)
  114. // 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  115. // 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  116. //
  117. // 1047 is Pt1000 with 4k7 pullup
  118. // 1010 is Pt1000 with 1k pullup (non standard)
  119. // 147 is Pt100 with 4k7 pullup
  120. // 110 is Pt100 with 1k pullup (non standard)
  121. // 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
  122. // Use it for Testing or Development purposes. NEVER for production machine.
  123. //#define DUMMY_THERMISTOR_998_VALUE 25
  124. //#define DUMMY_THERMISTOR_999_VALUE 100
  125. // :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
  126. #define TEMP_SENSOR_0 1
  127. #define TEMP_SENSOR_1 0
  128. #define TEMP_SENSOR_2 0
  129. #define TEMP_SENSOR_3 0
  130. #define TEMP_SENSOR_BED 1
  131. // This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
  132. //#define TEMP_SENSOR_1_AS_REDUNDANT
  133. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  134. // Actual temperature must be close to target for this long before M109 returns success
  135. #define TEMP_RESIDENCY_TIME 15 // (seconds)
  136. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  137. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  138. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  139. // to check that the wiring to the thermistor is not broken.
  140. // Otherwise this would lead to the heater being powered on all the time.
  141. #define HEATER_0_MINTEMP 5
  142. #define HEATER_1_MINTEMP 5
  143. #define HEATER_2_MINTEMP 5
  144. #define HEATER_3_MINTEMP 5
  145. #define BED_MINTEMP 5
  146. // When temperature exceeds max temp, your heater will be switched off.
  147. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  148. // You should use MINTEMP for thermistor short/failure protection.
  149. #define HEATER_0_MAXTEMP 275
  150. #define HEATER_1_MAXTEMP 275
  151. #define HEATER_2_MAXTEMP 275
  152. #define HEATER_3_MAXTEMP 275
  153. #define BED_MAXTEMP 150
  154. // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
  155. //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
  156. //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
  157. //===========================================================================
  158. //============================= PID Settings ================================
  159. //===========================================================================
  160. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  161. // Comment the following line to disable PID and enable bang-bang.
  162. #define PIDTEMP
  163. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  164. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  165. #if ENABLED(PIDTEMP)
  166. //#define PID_DEBUG // Sends debug data to the serial port.
  167. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  168. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  169. //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  170. // Set/get with gcode: M301 E[extruder number, 0-2]
  171. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  172. // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  173. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
  174. #define K1 0.95 //smoothing factor within the PID
  175. // Felix 2.0+ electronics with v4 Hotend
  176. #define DEFAULT_Kp 12
  177. #define DEFAULT_Ki 0.84
  178. #define DEFAULT_Kd 85
  179. #endif // PIDTEMP
  180. //===========================================================================
  181. //============================= PID > Bed Temperature Control ===============
  182. //===========================================================================
  183. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  184. //
  185. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  186. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  187. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  188. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  189. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  190. // shouldn't use bed PID until someone else verifies your hardware works.
  191. // If this is enabled, find your own PID constants below.
  192. #define PIDTEMPBED
  193. //#define BED_LIMIT_SWITCHING
  194. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  195. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  196. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  197. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  198. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  199. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  200. #if ENABLED(PIDTEMPBED)
  201. #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
  202. // Felix Foil Heater
  203. #define DEFAULT_bedKp 103.37
  204. #define DEFAULT_bedKi 2.79
  205. #define DEFAULT_bedKd 956.94
  206. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  207. #endif // PIDTEMPBED
  208. // @section extruder
  209. //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
  210. //can be software-disabled for whatever purposes by
  211. #define PREVENT_DANGEROUS_EXTRUDE
  212. //if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
  213. #define PREVENT_LENGTHY_EXTRUDE
  214. #define EXTRUDE_MINTEMP 170
  215. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
  216. //===========================================================================
  217. //======================== Thermal Runaway Protection =======================
  218. //===========================================================================
  219. /**
  220. * Thermal Runaway Protection protects your printer from damage and fire if a
  221. * thermistor falls out or temperature sensors fail in any way.
  222. *
  223. * The issue: If a thermistor falls out or a temperature sensor fails,
  224. * Marlin can no longer sense the actual temperature. Since a disconnected
  225. * thermistor reads as a low temperature, the firmware will keep the heater on.
  226. *
  227. * The solution: Once the temperature reaches the target, start observing.
  228. * If the temperature stays too far below the target (hysteresis) for too long,
  229. * the firmware will halt as a safety precaution.
  230. */
  231. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  232. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  233. //===========================================================================
  234. //============================= Mechanical Settings =========================
  235. //===========================================================================
  236. // @section machine
  237. // Uncomment this option to enable CoreXY kinematics
  238. //#define COREXY
  239. // Uncomment this option to enable CoreXZ kinematics
  240. //#define COREXZ
  241. // Enable this option for Toshiba steppers
  242. //#define CONFIG_STEPPERS_TOSHIBA
  243. // @section homing
  244. // coarse Endstop Settings
  245. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  246. #if DISABLED(ENDSTOPPULLUPS)
  247. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  248. //#define ENDSTOPPULLUP_XMAX
  249. //#define ENDSTOPPULLUP_YMAX
  250. //#define ENDSTOPPULLUP_ZMAX
  251. //#define ENDSTOPPULLUP_XMIN
  252. //#define ENDSTOPPULLUP_YMIN
  253. //#define ENDSTOPPULLUP_ZMIN
  254. //#define ENDSTOPPULLUP_ZMIN_PROBE
  255. #endif
  256. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  257. const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
  258. const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
  259. const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
  260. const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
  261. const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
  262. const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
  263. const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
  264. #define DISABLE_MAX_ENDSTOPS
  265. //#define DISABLE_MIN_ENDSTOPS
  266. // If you want to enable the Z probe pin, but disable its use, uncomment the line below.
  267. // This only affects a Z probe endstop if you have separate Z min endstop as well and have
  268. // activated Z_MIN_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z probe,
  269. // this has no effect.
  270. //#define DISABLE_Z_MIN_PROBE_ENDSTOP
  271. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  272. // :{0:'Low',1:'High'}
  273. #define X_ENABLE_ON 0
  274. #define Y_ENABLE_ON 0
  275. #define Z_ENABLE_ON 0
  276. #define E_ENABLE_ON 0 // For all extruders
  277. // Disables axis stepper immediately when it's not being used.
  278. // WARNING: When motors turn off there is a chance of losing position accuracy!
  279. #define DISABLE_X false
  280. #define DISABLE_Y false
  281. #define DISABLE_Z false
  282. // Warn on display about possibly reduced accuracy
  283. //#define DISABLE_REDUCED_ACCURACY_WARNING
  284. // @section extruder
  285. #define DISABLE_E false // For all extruders
  286. #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
  287. // @section machine
  288. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  289. #define INVERT_X_DIR true
  290. #define INVERT_Y_DIR true
  291. #define INVERT_Z_DIR true
  292. // @section extruder
  293. // For direct drive extruder v9 set to true, for geared extruder set to false.
  294. #define INVERT_E0_DIR false
  295. #define INVERT_E1_DIR false
  296. #define INVERT_E2_DIR false
  297. #define INVERT_E3_DIR false
  298. // @section homing
  299. // ENDSTOP SETTINGS:
  300. // Sets direction of endstops when homing; 1=MAX, -1=MIN
  301. // :[-1,1]
  302. #define X_HOME_DIR -1
  303. #define Y_HOME_DIR -1
  304. #define Z_HOME_DIR -1
  305. #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
  306. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
  307. // @section machine
  308. // Travel limits after homing (units are in mm)
  309. #define X_MIN_POS 0
  310. #define Y_MIN_POS 0
  311. #define Z_MIN_POS 0
  312. #define X_MAX_POS 255
  313. #define Y_MAX_POS 205
  314. #define Z_MAX_POS 235
  315. //===========================================================================
  316. //========================= Filament Runout Sensor ==========================
  317. //===========================================================================
  318. //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
  319. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
  320. // It is assumed that when logic high = filament available
  321. // when logic low = filament ran out
  322. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  323. const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
  324. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  325. #define FILAMENT_RUNOUT_SCRIPT "M600"
  326. #endif
  327. //===========================================================================
  328. //============================ Mesh Bed Leveling ============================
  329. //===========================================================================
  330. //#define MESH_BED_LEVELING // Enable mesh bed leveling.
  331. #if ENABLED(MESH_BED_LEVELING)
  332. #define MESH_MIN_X 10
  333. #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
  334. #define MESH_MIN_Y 10
  335. #define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y)
  336. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
  337. #define MESH_NUM_Y_POINTS 3
  338. #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
  339. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
  340. #if ENABLED(MANUAL_BED_LEVELING)
  341. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  342. #endif // MANUAL_BED_LEVELING
  343. #endif // MESH_BED_LEVELING
  344. //===========================================================================
  345. //============================ Bed Auto Leveling ============================
  346. //===========================================================================
  347. // @section bedlevel
  348. //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
  349. //#define DEBUG_LEVELING_FEATURE
  350. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
  351. #if ENABLED(AUTO_BED_LEVELING_FEATURE)
  352. // There are 2 different ways to specify probing locations:
  353. //
  354. // - "grid" mode
  355. // Probe several points in a rectangular grid.
  356. // You specify the rectangle and the density of sample points.
  357. // This mode is preferred because there are more measurements.
  358. //
  359. // - "3-point" mode
  360. // Probe 3 arbitrary points on the bed (that aren't collinear)
  361. // You specify the XY coordinates of all 3 points.
  362. // Enable this to sample the bed in a grid (least squares solution).
  363. // Note: this feature generates 10KB extra code size.
  364. #define AUTO_BED_LEVELING_GRID
  365. #if ENABLED(AUTO_BED_LEVELING_GRID)
  366. #define LEFT_PROBE_BED_POSITION 15
  367. #define RIGHT_PROBE_BED_POSITION 170
  368. #define FRONT_PROBE_BED_POSITION 20
  369. #define BACK_PROBE_BED_POSITION 180
  370. #define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
  371. // Set the number of grid points per dimension.
  372. // You probably don't need more than 3 (squared=9).
  373. #define AUTO_BED_LEVELING_GRID_POINTS 2
  374. #else // !AUTO_BED_LEVELING_GRID
  375. // Arbitrary points to probe.
  376. // A simple cross-product is used to estimate the plane of the bed.
  377. #define ABL_PROBE_PT_1_X 15
  378. #define ABL_PROBE_PT_1_Y 180
  379. #define ABL_PROBE_PT_2_X 15
  380. #define ABL_PROBE_PT_2_Y 20
  381. #define ABL_PROBE_PT_3_X 170
  382. #define ABL_PROBE_PT_3_Y 20
  383. #endif // AUTO_BED_LEVELING_GRID
  384. // Offsets to the Z probe relative to the nozzle tip.
  385. // X and Y offsets must be integers.
  386. #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Z probe to nozzle X offset: -left +right
  387. #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z probe to nozzle Y offset: -front +behind
  388. #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z probe to nozzle Z offset: -below (always!)
  389. #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
  390. // Be sure you have this distance over your Z_MAX_POS in case.
  391. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
  392. #define Z_RAISE_BEFORE_PROBING 15 // How much the Z axis will be raised before traveling to the first probing point.
  393. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points.
  394. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point.
  395. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
  396. // Useful to retract a deployable Z probe.
  397. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
  398. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  399. // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
  400. // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
  401. #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area.
  402. // When defined, it will:
  403. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  404. // - If stepper drivers timeout, it will need X and Y homing again before Z homing.
  405. // - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28).
  406. // - Block Z homing only when the Z probe is outside bed area.
  407. #if ENABLED(Z_SAFE_HOMING)
  408. #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
  409. #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
  410. #endif
  411. // Support for a dedicated Z probe endstop separate from the Z min endstop.
  412. // If you would like to use both a Z probe and a Z min endstop together,
  413. // uncomment #define Z_MIN_PROBE_ENDSTOP and read the instructions below.
  414. // If you still want to use the Z min endstop for homing, disable Z_SAFE_HOMING above.
  415. // Example: To park the head outside the bed area when homing with G28.
  416. //
  417. // WARNING:
  418. // The Z min endstop will need to set properly as it would without a Z probe
  419. // to prevent head crashes and premature stopping during a print.
  420. //
  421. // To use a separate Z probe endstop, you must have a Z_MIN_PROBE_PIN
  422. // defined in the pins_XXXXX.h file for your control board.
  423. // If you are using a servo based Z probe, you will need to enable NUM_SERVOS,
  424. // Z_ENDSTOP_SERVO_NR and SERVO_ENDSTOP_ANGLES in the R/C SERVO support below.
  425. // RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin
  426. // in the Aux 4 section of the RAMPS board. Use 5V for powered sensors,
  427. // otherwise connect to ground and D32 for normally closed configuration
  428. // and 5V and D32 for normally open configurations.
  429. // Normally closed configuration is advised and assumed.
  430. // The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin.
  431. // Z_MIN_PROBE_PIN is setting the pin to use on the Arduino.
  432. // Since the D32 pin on the RAMPS maps to D32 on Arduino, this works.
  433. // D32 is currently selected in the RAMPS 1.3/1.4 pin file.
  434. // All other boards will need changes to the respective pins_XXXXX.h file.
  435. //
  436. // WARNING:
  437. // Setting the wrong pin may have unexpected and potentially disastrous outcomes.
  438. // Use with caution and do your homework.
  439. //
  440. //#define Z_MIN_PROBE_ENDSTOP
  441. #endif // AUTO_BED_LEVELING_FEATURE
  442. // @section homing
  443. // The position of the homing switches
  444. //#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
  445. //#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
  446. // Manual homing switch locations:
  447. // For deltabots this means top and center of the Cartesian print volume.
  448. #if ENABLED(MANUAL_HOME_POSITIONS)
  449. #define MANUAL_X_HOME_POS 0
  450. #define MANUAL_Y_HOME_POS 0
  451. #define MANUAL_Z_HOME_POS 0
  452. //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
  453. #endif
  454. // @section movement
  455. /**
  456. * MOVEMENT SETTINGS
  457. */
  458. #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
  459. // default settings
  460. // default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
  461. #define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
  462. #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
  463. #define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
  464. #define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
  465. #define DEFAULT_RETRACT_ACCELERATION 5000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
  466. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
  467. // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
  468. #define DEFAULT_XYJERK 10 // (mm/sec)
  469. #define DEFAULT_ZJERK 0.3 //0.4 // (mm/sec)
  470. #define DEFAULT_EJERK 5.0 // (mm/sec)
  471. //=============================================================================
  472. //============================= Additional Features ===========================
  473. //=============================================================================
  474. // @section more
  475. // Custom M code points
  476. #define CUSTOM_M_CODES
  477. #if ENABLED(CUSTOM_M_CODES)
  478. #if ENABLED(AUTO_BED_LEVELING_FEATURE)
  479. #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
  480. #define Z_PROBE_OFFSET_RANGE_MIN -20
  481. #define Z_PROBE_OFFSET_RANGE_MAX 20
  482. #endif
  483. #endif
  484. // @section extras
  485. // EEPROM
  486. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  487. // M500 - stores parameters in EEPROM
  488. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  489. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  490. //define this to enable EEPROM support
  491. //#define EEPROM_SETTINGS
  492. #if ENABLED(EEPROM_SETTINGS)
  493. // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
  494. #define EEPROM_CHITCHAT // Please keep turned on if you can.
  495. #endif
  496. //
  497. // M100 Free Memory Watcher
  498. //
  499. //#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
  500. // @section temperature
  501. // Preheat Constants
  502. #define PLA_PREHEAT_HOTEND_TEMP 180
  503. #define PLA_PREHEAT_HPB_TEMP 70
  504. #define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
  505. #define ABS_PREHEAT_HOTEND_TEMP 240
  506. #define ABS_PREHEAT_HPB_TEMP 100
  507. #define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
  508. //==============================LCD and SD support=============================
  509. // @section lcd
  510. // Define your display language below. Replace (en) with your language code and uncomment.
  511. // en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
  512. // See also language.h
  513. //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
  514. // Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
  515. // To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
  516. // See also documentation/LCDLanguageFont.md
  517. #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware
  518. //#define DISPLAY_CHARSET_HD44780_WESTERN
  519. //#define DISPLAY_CHARSET_HD44780_CYRILLIC
  520. //#define ULTRA_LCD //general LCD support, also 16x2
  521. //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
  522. //#define SDSUPPORT // Enable SD Card Support in Hardware Console
  523. // Changed behaviour! If you need SDSUPPORT uncomment it!
  524. //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
  525. //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
  526. //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
  527. //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
  528. //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
  529. //#define ULTIPANEL //the UltiPanel as on Thingiverse
  530. //#define SPEAKER // The sound device is a speaker - not a buzzer. A buzzer resonates with his own frequency.
  531. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
  532. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
  533. // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
  534. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  535. // http://reprap.org/wiki/PanelOne
  536. //#define PANEL_ONE
  537. // The MaKr3d Makr-Panel with graphic controller and SD support
  538. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  539. //#define MAKRPANEL
  540. // The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
  541. // http://panucatt.com
  542. // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
  543. //#define VIKI2
  544. //#define miniVIKI
  545. // This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  546. //
  547. // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
  548. //#define ELB_FULL_GRAPHIC_CONTROLLER
  549. //#define SD_DETECT_INVERTED
  550. // The RepRapDiscount Smart Controller (white PCB)
  551. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  552. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  553. // The GADGETS3D G3D LCD/SD Controller (blue PCB)
  554. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  555. //#define G3D_PANEL
  556. // The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
  557. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  558. //
  559. // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
  560. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  561. // The RepRapWorld REPRAPWORLD_KEYPAD v1.1
  562. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  563. //#define REPRAPWORLD_KEYPAD
  564. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
  565. // The Elefu RA Board Control Panel
  566. // http://www.elefu.com/index.php?route=product/product&product_id=53
  567. // REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  568. //#define RA_CONTROL_PANEL
  569. // The MakerLab Mini Panel with graphic controller and SD support
  570. // http://reprap.org/wiki/Mini_panel
  571. //#define MINIPANEL
  572. /**
  573. * I2C Panels
  574. */
  575. //#define LCD_I2C_SAINSMART_YWROBOT
  576. // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
  577. //
  578. // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
  579. // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
  580. // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
  581. // Note: The PANELOLU2 encoder click input can either be directly connected to a pin
  582. // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  583. //#define LCD_I2C_PANELOLU2
  584. // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
  585. //#define LCD_I2C_VIKI
  586. // SSD1306 OLED generic display support
  587. // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
  588. //#define U8GLIB_SSD1306
  589. // Shift register panels
  590. // ---------------------
  591. // 2 wire Non-latching LCD SR from:
  592. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
  593. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  594. //#define SAV_3DLCD
  595. // @section extras
  596. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  597. #define FAST_PWM_FAN
  598. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  599. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  600. // is too low, you should also increment SOFT_PWM_SCALE.
  601. //#define FAN_SOFT_PWM
  602. // Incrementing this by 1 will double the software PWM frequency,
  603. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  604. // However, control resolution will be halved for each increment;
  605. // at zero value, there are 128 effective control positions.
  606. #define SOFT_PWM_SCALE 0
  607. // Temperature status LEDs that display the hotend and bet temperature.
  608. // If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
  609. // Otherwise the RED led is on. There is 1C hysteresis.
  610. //#define TEMP_STAT_LEDS
  611. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  612. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  613. //#define PHOTOGRAPH_PIN 23
  614. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  615. //#define SF_ARC_FIX
  616. // Support for the BariCUDA Paste Extruder.
  617. //#define BARICUDA
  618. //define BlinkM/CyzRgb Support
  619. //#define BLINKM
  620. /*********************************************************************\
  621. * R/C SERVO support
  622. * Sponsored by TrinityLabs, Reworked by codexmas
  623. **********************************************************************/
  624. // Number of servos
  625. //
  626. // If you select a configuration below, this will receive a default value and does not need to be set manually
  627. // set it manually if you have more servos than extruders and wish to manually control some
  628. // leaving it undefined or defining as 0 will disable the servo subsystem
  629. // If unsure, leave commented / disabled
  630. //
  631. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  632. // Servo Endstops
  633. //
  634. // This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
  635. // Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500.
  636. //
  637. //#define X_ENDSTOP_SERVO_NR 1
  638. //#define Y_ENDSTOP_SERVO_NR 2
  639. //#define Z_ENDSTOP_SERVO_NR 0
  640. //#define SERVO_ENDSTOP_ANGLES {{0,0}, {0,0}, {70,0}} // X,Y,Z Axis Extend and Retract angles
  641. // Servo deactivation
  642. //
  643. // With this option servos are powered only during movement, then turned off to prevent jitter.
  644. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  645. #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
  646. // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
  647. // 300ms is a good value but you can try less delay.
  648. // If the servo can't reach the requested position, increase it.
  649. #define SERVO_DEACTIVATION_DELAY 300
  650. #endif
  651. /**********************************************************************\
  652. * Support for a filament diameter sensor
  653. * Also allows adjustment of diameter at print time (vs at slicing)
  654. * Single extruder only at this point (extruder 0)
  655. *
  656. * Motherboards
  657. * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
  658. * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
  659. * 301 - Rambo - uses Analog input 3
  660. * Note may require analog pins to be defined for different motherboards
  661. **********************************************************************/
  662. // Uncomment below to enable
  663. //#define FILAMENT_SENSOR
  664. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
  665. #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
  666. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
  667. #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
  668. #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
  669. #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm) - limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
  670. //defines used in the code
  671. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
  672. //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
  673. //#define FILAMENT_LCD_DISPLAY
  674. #include "Configuration_adv.h"
  675. #include "thermistortables.h"
  676. #endif //CONFIGURATION_H