My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Ви не можете вибрати більше 25 тем Теми мають розпочинатися з літери або цифри, можуть містити дефіси (-) і не повинні перевищувати 35 символів.

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915191619171918191919201921192219231924192519261927192819291930193119321933193419351936193719381939194019411942194319441945194619471948194919501951195219531954195519561957195819591960196119621963196419651966196719681969197019711972197319741975197619771978197919801981198219831984198519861987198819891990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026202720282029203020312032203320342035203620372038203920402041204220432044204520462047204820492050205120522053205420552056205720582059206020612062206320642065206620672068206920702071207220732074207520762077207820792080208120822083208420852086208720882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149215021512152215321542155215621572158215921602161216221632164216521662167216821692170217121722173217421752176217721782179218021812182218321842185218621872188218921902191219221932194219521962197219821992200220122022203220422052206220722082209221022112212221322142215221622172218221922202221222222232224222522262227222822292230223122322233223422352236223722382239224022412242224322442245224622472248224922502251225222532254225522562257225822592260226122622263226422652266226722682269227022712272227322742275227622772278227922802281228222832284228522862287228822892290229122922293229422952296229722982299230023012302230323042305230623072308230923102311231223132314231523162317231823192320232123222323232423252326232723282329233023312332233323342335233623372338233923402341234223432344234523462347234823492350235123522353235423552356235723582359236023612362236323642365236623672368236923702371237223732374237523762377237823792380238123822383238423852386238723882389239023912392239323942395239623972398239924002401240224032404240524062407240824092410241124122413241424152416241724182419242024212422242324242425242624272428242924302431243224332434243524362437243824392440244124422443244424452446244724482449245024512452245324542455245624572458245924602461246224632464246524662467246824692470247124722473247424752476247724782479248024812482248324842485248624872488248924902491249224932494249524962497249824992500250125022503250425052506250725082509251025112512251325142515251625172518251925202521252225232524252525262527252825292530253125322533253425352536253725382539254025412542254325442545254625472548254925502551255225532554255525562557255825592560256125622563256425652566256725682569257025712572257325742575257625772578257925802581258225832584258525862587258825892590259125922593259425952596259725982599260026012602260326042605260626072608260926102611261226132614261526162617261826192620262126222623262426252626262726282629263026312632263326342635263626372638263926402641264226432644264526462647264826492650265126522653265426552656265726582659266026612662266326642665266626672668266926702671267226732674267526762677267826792680268126822683268426852686268726882689269026912692269326942695269626972698269927002701270227032704270527062707270827092710271127122713271427152716271727182719272027212722272327242725272627272728272927302731273227332734273527362737273827392740274127422743274427452746274727482749275027512752275327542755275627572758275927602761276227632764276527662767276827692770277127722773277427752776277727782779278027812782278327842785278627872788278927902791279227932794279527962797279827992800280128022803280428052806280728082809281028112812281328142815281628172818281928202821282228232824282528262827282828292830283128322833283428352836283728382839284028412842284328442845284628472848284928502851285228532854285528562857285828592860286128622863286428652866286728682869287028712872287328742875287628772878287928802881288228832884288528862887288828892890289128922893289428952896289728982899290029012902290329042905290629072908290929102911291229132914291529162917291829192920292129222923292429252926292729282929293029312932293329342935293629372938293929402941294229432944294529462947294829492950295129522953295429552956295729582959296029612962296329642965296629672968296929702971297229732974297529762977297829792980298129822983298429852986
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. */
  37. #define CONFIGURATION_H_VERSION 02000903
  38. //===========================================================================
  39. //============================= Getting Started =============================
  40. //===========================================================================
  41. /**
  42. * Here are some useful links to help get your machine configured and calibrated:
  43. *
  44. * Example Configs: https://github.com/MarlinFirmware/Configurations/branches/all
  45. *
  46. * Průša Calculator: https://blog.prusaprinters.org/calculator_3416/
  47. *
  48. * Calibration Guides: https://reprap.org/wiki/Calibration
  49. * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * https://youtu.be/wAL9d7FgInk
  52. *
  53. * Calibration Objects: https://www.thingiverse.com/thing:5573
  54. * https://www.thingiverse.com/thing:1278865
  55. */
  56. //===========================================================================
  57. //========================== DELTA / SCARA / TPARA ==========================
  58. //===========================================================================
  59. //
  60. // Download configurations from the link above and customize for your machine.
  61. // Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
  62. //
  63. //===========================================================================
  64. // @section info
  65. // Author info of this build printed to the host during boot and M115
  66. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  67. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  68. /**
  69. * *** VENDORS PLEASE READ ***
  70. *
  71. * Marlin allows you to add a custom boot image for Graphical LCDs.
  72. * With this option Marlin will first show your custom screen followed
  73. * by the standard Marlin logo with version number and web URL.
  74. *
  75. * We encourage you to take advantage of this new feature and we also
  76. * respectfully request that you retain the unmodified Marlin boot screen.
  77. */
  78. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  79. #define SHOW_BOOTSCREEN
  80. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  81. //#define SHOW_CUSTOM_BOOTSCREEN
  82. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  83. //#define CUSTOM_STATUS_SCREEN_IMAGE
  84. // @section machine
  85. // Choose the name from boards.h that matches your setup
  86. #ifndef MOTHERBOARD
  87. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  88. #endif
  89. /**
  90. * Select the serial port on the board to use for communication with the host.
  91. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  92. * Serial port -1 is the USB emulated serial port, if available.
  93. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  94. *
  95. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  96. */
  97. #define SERIAL_PORT 0
  98. /**
  99. * Serial Port Baud Rate
  100. * This is the default communication speed for all serial ports.
  101. * Set the baud rate defaults for additional serial ports below.
  102. *
  103. * 250000 works in most cases, but you might try a lower speed if
  104. * you commonly experience drop-outs during host printing.
  105. * You may try up to 1000000 to speed up SD file transfer.
  106. *
  107. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  108. */
  109. #define BAUDRATE 250000
  110. //#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate
  111. /**
  112. * Select a secondary serial port on the board to use for communication with the host.
  113. * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  114. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  115. */
  116. //#define SERIAL_PORT_2 -1
  117. //#define BAUDRATE_2 250000 // Enable to override BAUDRATE
  118. /**
  119. * Select a third serial port on the board to use for communication with the host.
  120. * Currently only supported for AVR, DUE, LPC1768/9 and STM32/STM32F1
  121. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  122. */
  123. //#define SERIAL_PORT_3 1
  124. //#define BAUDRATE_3 250000 // Enable to override BAUDRATE
  125. // Enable the Bluetooth serial interface on AT90USB devices
  126. //#define BLUETOOTH
  127. // Name displayed in the LCD "Ready" message and Info menu
  128. //#define CUSTOM_MACHINE_NAME "3D Printer"
  129. // Printer's unique ID, used by some programs to differentiate between machines.
  130. // Choose your own or use a service like https://www.uuidgenerator.net/version4
  131. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  132. /**
  133. * Define the number of coordinated linear axes.
  134. * See https://github.com/DerAndere1/Marlin/wiki
  135. * Each linear axis gets its own stepper control and endstop:
  136. *
  137. * Steppers: *_STEP_PIN, *_ENABLE_PIN, *_DIR_PIN, *_ENABLE_ON
  138. * Endstops: *_STOP_PIN, USE_*MIN_PLUG, USE_*MAX_PLUG
  139. * Axes: *_MIN_POS, *_MAX_POS, INVERT_*_DIR
  140. * Planner: DEFAULT_AXIS_STEPS_PER_UNIT, DEFAULT_MAX_FEEDRATE
  141. * DEFAULT_MAX_ACCELERATION, AXIS_RELATIVE_MODES,
  142. * MICROSTEP_MODES, MANUAL_FEEDRATE
  143. *
  144. * :[3, 4, 5, 6]
  145. */
  146. //#define LINEAR_AXES 3
  147. /**
  148. * Axis codes for additional axes:
  149. * This defines the axis code that is used in G-code commands to
  150. * reference a specific axis.
  151. * 'A' for rotational axis parallel to X
  152. * 'B' for rotational axis parallel to Y
  153. * 'C' for rotational axis parallel to Z
  154. * 'U' for secondary linear axis parallel to X
  155. * 'V' for secondary linear axis parallel to Y
  156. * 'W' for secondary linear axis parallel to Z
  157. * Regardless of the settings, firmware-internal axis IDs are
  158. * I (AXIS4), J (AXIS5), K (AXIS6).
  159. */
  160. #if LINEAR_AXES >= 4
  161. #define AXIS4_NAME 'A' // :['A', 'B', 'C', 'U', 'V', 'W']
  162. #endif
  163. #if LINEAR_AXES >= 5
  164. #define AXIS5_NAME 'B' // :['A', 'B', 'C', 'U', 'V', 'W']
  165. #endif
  166. #if LINEAR_AXES >= 6
  167. #define AXIS6_NAME 'C' // :['A', 'B', 'C', 'U', 'V', 'W']
  168. #endif
  169. // @section extruder
  170. // This defines the number of extruders
  171. // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
  172. #define EXTRUDERS 1
  173. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  174. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  175. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  176. //#define SINGLENOZZLE
  177. // Save and restore temperature and fan speed on tool-change.
  178. // Set standby for the unselected tool with M104/106/109 T...
  179. #if ENABLED(SINGLENOZZLE)
  180. //#define SINGLENOZZLE_STANDBY_TEMP
  181. //#define SINGLENOZZLE_STANDBY_FAN
  182. #endif
  183. /**
  184. * Multi-Material Unit
  185. * Set to one of these predefined models:
  186. *
  187. * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version)
  188. * PRUSA_MMU2 : Průša MMU2
  189. * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
  190. * EXTENDABLE_EMU_MMU2 : MMU with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  191. * EXTENDABLE_EMU_MMU2S : MMUS with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  192. *
  193. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  194. * See additional options in Configuration_adv.h.
  195. */
  196. //#define MMU_MODEL PRUSA_MMU2
  197. // A dual extruder that uses a single stepper motor
  198. //#define SWITCHING_EXTRUDER
  199. #if ENABLED(SWITCHING_EXTRUDER)
  200. #define SWITCHING_EXTRUDER_SERVO_NR 0
  201. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  202. #if EXTRUDERS > 3
  203. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  204. #endif
  205. #endif
  206. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  207. //#define SWITCHING_NOZZLE
  208. #if ENABLED(SWITCHING_NOZZLE)
  209. #define SWITCHING_NOZZLE_SERVO_NR 0
  210. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  211. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  212. #endif
  213. /**
  214. * Two separate X-carriages with extruders that connect to a moving part
  215. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  216. */
  217. //#define PARKING_EXTRUDER
  218. /**
  219. * Two separate X-carriages with extruders that connect to a moving part
  220. * via a magnetic docking mechanism using movements and no solenoid
  221. *
  222. * project : https://www.thingiverse.com/thing:3080893
  223. * movements : https://youtu.be/0xCEiG9VS3k
  224. * https://youtu.be/Bqbcs0CU2FE
  225. */
  226. //#define MAGNETIC_PARKING_EXTRUDER
  227. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  228. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  229. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  230. #if ENABLED(PARKING_EXTRUDER)
  231. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  232. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  233. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  234. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  235. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  236. #define MPE_FAST_SPEED 9000 // (mm/min) Speed for travel before last distance point
  237. #define MPE_SLOW_SPEED 4500 // (mm/min) Speed for last distance travel to park and couple
  238. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  239. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  240. #endif
  241. #endif
  242. /**
  243. * Switching Toolhead
  244. *
  245. * Support for swappable and dockable toolheads, such as
  246. * the E3D Tool Changer. Toolheads are locked with a servo.
  247. */
  248. //#define SWITCHING_TOOLHEAD
  249. /**
  250. * Magnetic Switching Toolhead
  251. *
  252. * Support swappable and dockable toolheads with a magnetic
  253. * docking mechanism using movement and no servo.
  254. */
  255. //#define MAGNETIC_SWITCHING_TOOLHEAD
  256. /**
  257. * Electromagnetic Switching Toolhead
  258. *
  259. * Parking for CoreXY / HBot kinematics.
  260. * Toolheads are parked at one edge and held with an electromagnet.
  261. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  262. */
  263. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  264. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  265. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  266. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  267. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  268. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  269. #if ENABLED(SWITCHING_TOOLHEAD)
  270. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  271. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  272. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  273. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  274. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  275. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  276. #if ENABLED(PRIME_BEFORE_REMOVE)
  277. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  278. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  279. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/min) Extruder prime feedrate
  280. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/min) Extruder retract feedrate
  281. #endif
  282. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  283. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  284. #endif
  285. #endif
  286. /**
  287. * "Mixing Extruder"
  288. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  289. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  290. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  291. * - This implementation supports up to two mixing extruders.
  292. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  293. */
  294. //#define MIXING_EXTRUDER
  295. #if ENABLED(MIXING_EXTRUDER)
  296. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  297. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  298. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  299. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  300. //#define MIXING_PRESETS // Assign 8 default V-tool presets for 2 or 3 MIXING_STEPPERS
  301. #if ENABLED(GRADIENT_MIX)
  302. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  303. #endif
  304. #endif
  305. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  306. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  307. // For the other hotends it is their distance from the extruder 0 hotend.
  308. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  309. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  310. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  311. // @section machine
  312. /**
  313. * Power Supply Control
  314. *
  315. * Enable and connect the power supply to the PS_ON_PIN.
  316. * Specify whether the power supply is active HIGH or active LOW.
  317. */
  318. //#define PSU_CONTROL
  319. //#define PSU_NAME "Power Supply"
  320. #if ENABLED(PSU_CONTROL)
  321. //#define MKS_PWC // Using the MKS PWC add-on
  322. //#define PS_OFF_CONFIRM // Confirm dialog when power off
  323. //#define PS_OFF_SOUND // Beep 1s when power off
  324. #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box
  325. //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
  326. //#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power
  327. //#define PSU_POWERUP_GCODE "M355 S1" // G-code to run after power-on (e.g., case light on)
  328. //#define PSU_POWEROFF_GCODE "M355 S0" // G-code to run before power-off (e.g., case light off)
  329. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  330. #if ENABLED(AUTO_POWER_CONTROL)
  331. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  332. #define AUTO_POWER_E_FANS
  333. #define AUTO_POWER_CONTROLLERFAN
  334. #define AUTO_POWER_CHAMBER_FAN
  335. #define AUTO_POWER_COOLER_FAN
  336. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU if any extruder is over this temperature
  337. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU if the chamber is over this temperature
  338. //#define AUTO_POWER_COOLER_TEMP 26 // (°C) Turn on PSU if the cooler is over this temperature
  339. #define POWER_TIMEOUT 30 // (s) Turn off power if the machine is idle for this duration
  340. //#define POWER_OFF_DELAY 60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
  341. #endif
  342. #endif
  343. //===========================================================================
  344. //============================= Thermal Settings ============================
  345. //===========================================================================
  346. // @section temperature
  347. /**
  348. * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  349. *
  350. * Temperature sensors available:
  351. *
  352. * SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
  353. * -------
  354. * -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
  355. * NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
  356. * -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
  357. * -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
  358. *
  359. * NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
  360. * Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
  361. * Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
  362. * Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
  363. *
  364. * Analog Themocouple Boards
  365. * -------
  366. * -4 : AD8495 with Thermocouple
  367. * -1 : AD595 with Thermocouple
  368. *
  369. * Analog Thermistors - 4.7kΩ pullup - Normal
  370. * -------
  371. * 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
  372. * 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
  373. * 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
  374. * 2 : 200kΩ ATC Semitec 204GT-2
  375. * 202 : 200kΩ Copymaster 3D
  376. * 3 : ???Ω Mendel-parts thermistor
  377. * 4 : 10kΩ Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
  378. * 5 : 100kΩ ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
  379. * 501 : 100kΩ Zonestar - Tronxy X3A
  380. * 502 : 100kΩ Zonestar - used by hot bed in Zonestar Průša P802M
  381. * 512 : 100kΩ RPW-Ultra hotend
  382. * 6 : 100kΩ EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
  383. * 7 : 100kΩ Honeywell 135-104LAG-J01
  384. * 71 : 100kΩ Honeywell 135-104LAF-J01
  385. * 8 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT
  386. * 9 : 100kΩ GE Sensing AL03006-58.2K-97-G1
  387. * 10 : 100kΩ RS PRO 198-961
  388. * 11 : 100kΩ Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
  389. * 12 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
  390. * 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
  391. * 15 : 100kΩ Calibrated for JGAurora A5 hotend
  392. * 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
  393. * 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
  394. * 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
  395. * 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
  396. * 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
  397. * 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
  398. * 66 : 4.7MΩ Dyze Design High Temperature Thermistor
  399. * 67 : 500kΩ SliceEngineering 450°C Thermistor
  400. * 70 : 100kΩ bq Hephestos 2
  401. * 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
  402. * 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
  403. *
  404. * Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
  405. * ------- (but gives greater accuracy and more stable PID)
  406. * 51 : 100kΩ EPCOS (1kΩ pullup)
  407. * 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
  408. * 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
  409. *
  410. * Analog Thermistors - 10kΩ pullup - Atypical
  411. * -------
  412. * 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
  413. *
  414. * Analog RTDs (Pt100/Pt1000)
  415. * -------
  416. * 110 : Pt100 with 1kΩ pullup (atypical)
  417. * 147 : Pt100 with 4.7kΩ pullup
  418. * 1010 : Pt1000 with 1kΩ pullup (atypical)
  419. * 1047 : Pt1000 with 4.7kΩ pullup (E3D)
  420. * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  421. * NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
  422. * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
  423. * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  424. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  425. *
  426. * Custom/Dummy/Other Thermal Sensors
  427. * ------
  428. * 0 : not used
  429. * 1000 : Custom - Specify parameters in Configuration_adv.h
  430. *
  431. * !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  432. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  433. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  434. *
  435. */
  436. #define TEMP_SENSOR_0 1
  437. #define TEMP_SENSOR_1 0
  438. #define TEMP_SENSOR_2 0
  439. #define TEMP_SENSOR_3 0
  440. #define TEMP_SENSOR_4 0
  441. #define TEMP_SENSOR_5 0
  442. #define TEMP_SENSOR_6 0
  443. #define TEMP_SENSOR_7 0
  444. #define TEMP_SENSOR_BED 0
  445. #define TEMP_SENSOR_PROBE 0
  446. #define TEMP_SENSOR_CHAMBER 0
  447. #define TEMP_SENSOR_COOLER 0
  448. #define TEMP_SENSOR_BOARD 0
  449. #define TEMP_SENSOR_REDUNDANT 0
  450. // Dummy thermistor constant temperature readings, for use with 998 and 999
  451. #define DUMMY_THERMISTOR_998_VALUE 25
  452. #define DUMMY_THERMISTOR_999_VALUE 100
  453. // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
  454. //#define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000)
  455. //#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for Adafruit PT100; 4300 for Adafruit PT1000
  456. //#define MAX31865_SENSOR_OHMS_1 100
  457. //#define MAX31865_CALIBRATION_OHMS_1 430
  458. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  459. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  460. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  461. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  462. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  463. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  464. #define TEMP_CHAMBER_RESIDENCY_TIME 10 // (seconds) Time to wait for chamber to "settle" in M191
  465. #define TEMP_CHAMBER_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  466. #define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  467. /**
  468. * Redundant Temperature Sensor (TEMP_SENSOR_REDUNDANT)
  469. *
  470. * Use a temp sensor as a redundant sensor for another reading. Select an unused temperature sensor, and another
  471. * sensor you'd like it to be redundant for. If the two thermistors differ by TEMP_SENSOR_REDUNDANT_MAX_DIFF (°C),
  472. * the print will be aborted. Whichever sensor is selected will have its normal functions disabled; i.e. selecting
  473. * the Bed sensor (-1) will disable bed heating/monitoring.
  474. *
  475. * For selecting source/target use: COOLER, PROBE, BOARD, CHAMBER, BED, E0, E1, E2, E3, E4, E5, E6, E7
  476. */
  477. #if TEMP_SENSOR_REDUNDANT
  478. #define TEMP_SENSOR_REDUNDANT_SOURCE E1 // The sensor that will provide the redundant reading.
  479. #define TEMP_SENSOR_REDUNDANT_TARGET E0 // The sensor that we are providing a redundant reading for.
  480. #define TEMP_SENSOR_REDUNDANT_MAX_DIFF 10 // (°C) Temperature difference that will trigger a print abort.
  481. #endif
  482. // Below this temperature the heater will be switched off
  483. // because it probably indicates a broken thermistor wire.
  484. #define HEATER_0_MINTEMP 5
  485. #define HEATER_1_MINTEMP 5
  486. #define HEATER_2_MINTEMP 5
  487. #define HEATER_3_MINTEMP 5
  488. #define HEATER_4_MINTEMP 5
  489. #define HEATER_5_MINTEMP 5
  490. #define HEATER_6_MINTEMP 5
  491. #define HEATER_7_MINTEMP 5
  492. #define BED_MINTEMP 5
  493. #define CHAMBER_MINTEMP 5
  494. // Above this temperature the heater will be switched off.
  495. // This can protect components from overheating, but NOT from shorts and failures.
  496. // (Use MINTEMP for thermistor short/failure protection.)
  497. #define HEATER_0_MAXTEMP 275
  498. #define HEATER_1_MAXTEMP 275
  499. #define HEATER_2_MAXTEMP 275
  500. #define HEATER_3_MAXTEMP 275
  501. #define HEATER_4_MAXTEMP 275
  502. #define HEATER_5_MAXTEMP 275
  503. #define HEATER_6_MAXTEMP 275
  504. #define HEATER_7_MAXTEMP 275
  505. #define BED_MAXTEMP 150
  506. #define CHAMBER_MAXTEMP 60
  507. /**
  508. * Thermal Overshoot
  509. * During heatup (and printing) the temperature can often "overshoot" the target by many degrees
  510. * (especially before PID tuning). Setting the target temperature too close to MAXTEMP guarantees
  511. * a MAXTEMP shutdown! Use these values to forbid temperatures being set too close to MAXTEMP.
  512. */
  513. #define HOTEND_OVERSHOOT 15 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
  514. #define BED_OVERSHOOT 10 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
  515. #define COOLER_OVERSHOOT 2 // (°C) Forbid temperatures closer than OVERSHOOT
  516. //===========================================================================
  517. //============================= PID Settings ================================
  518. //===========================================================================
  519. // PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning
  520. // Comment the following line to disable PID and enable bang-bang.
  521. #define PIDTEMP
  522. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  523. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  524. #define PID_K1 0.95 // Smoothing factor within any PID loop
  525. #if ENABLED(PIDTEMP)
  526. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  527. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  528. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  529. // Set/get with gcode: M301 E[extruder number, 0-2]
  530. #if ENABLED(PID_PARAMS_PER_HOTEND)
  531. // Specify up to one value per hotend here, according to your setup.
  532. // If there are fewer values, the last one applies to the remaining hotends.
  533. #define DEFAULT_Kp_LIST { 22.20, 22.20 }
  534. #define DEFAULT_Ki_LIST { 1.08, 1.08 }
  535. #define DEFAULT_Kd_LIST { 114.00, 114.00 }
  536. #else
  537. #define DEFAULT_Kp 22.20
  538. #define DEFAULT_Ki 1.08
  539. #define DEFAULT_Kd 114.00
  540. #endif
  541. #endif // PIDTEMP
  542. //===========================================================================
  543. //====================== PID > Bed Temperature Control ======================
  544. //===========================================================================
  545. /**
  546. * PID Bed Heating
  547. *
  548. * If this option is enabled set PID constants below.
  549. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  550. *
  551. * The PID frequency will be the same as the extruder PWM.
  552. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  553. * which is fine for driving a square wave into a resistive load and does not significantly
  554. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  555. * heater. If your configuration is significantly different than this and you don't understand
  556. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  557. */
  558. //#define PIDTEMPBED
  559. //#define BED_LIMIT_SWITCHING
  560. /**
  561. * Max Bed Power
  562. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  563. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  564. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  565. */
  566. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  567. #if ENABLED(PIDTEMPBED)
  568. //#define MIN_BED_POWER 0
  569. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  570. // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  571. // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  572. #define DEFAULT_bedKp 10.00
  573. #define DEFAULT_bedKi .023
  574. #define DEFAULT_bedKd 305.4
  575. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  576. #endif // PIDTEMPBED
  577. //===========================================================================
  578. //==================== PID > Chamber Temperature Control ====================
  579. //===========================================================================
  580. /**
  581. * PID Chamber Heating
  582. *
  583. * If this option is enabled set PID constants below.
  584. * If this option is disabled, bang-bang will be used and CHAMBER_LIMIT_SWITCHING will enable
  585. * hysteresis.
  586. *
  587. * The PID frequency will be the same as the extruder PWM.
  588. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  589. * which is fine for driving a square wave into a resistive load and does not significantly
  590. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
  591. * heater. If your configuration is significantly different than this and you don't understand
  592. * the issues involved, don't use chamber PID until someone else verifies that your hardware works.
  593. */
  594. //#define PIDTEMPCHAMBER
  595. //#define CHAMBER_LIMIT_SWITCHING
  596. /**
  597. * Max Chamber Power
  598. * Applies to all forms of chamber control (PID, bang-bang, and bang-bang with hysteresis).
  599. * When set to any value below 255, enables a form of PWM to the chamber heater that acts like a divider
  600. * so don't use it unless you are OK with PWM on your heater. (See the comment on enabling PIDTEMPCHAMBER)
  601. */
  602. #define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
  603. #if ENABLED(PIDTEMPCHAMBER)
  604. #define MIN_CHAMBER_POWER 0
  605. //#define PID_CHAMBER_DEBUG // Sends debug data to the serial port.
  606. // Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
  607. // and placed inside the small Creality printer enclosure tent.
  608. //
  609. #define DEFAULT_chamberKp 37.04
  610. #define DEFAULT_chamberKi 1.40
  611. #define DEFAULT_chamberKd 655.17
  612. // M309 P37.04 I1.04 D655.17
  613. // FIND YOUR OWN: "M303 E-2 C8 S50" to run autotune on the chamber at 50 degreesC for 8 cycles.
  614. #endif // PIDTEMPCHAMBER
  615. #if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
  616. //#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
  617. //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  618. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  619. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  620. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  621. #endif
  622. // @section extruder
  623. /**
  624. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  625. * Add M302 to set the minimum extrusion temperature and/or turn
  626. * cold extrusion prevention on and off.
  627. *
  628. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  629. */
  630. #define PREVENT_COLD_EXTRUSION
  631. #define EXTRUDE_MINTEMP 170
  632. /**
  633. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  634. * Note: For Bowden Extruders make this large enough to allow load/unload.
  635. */
  636. #define PREVENT_LENGTHY_EXTRUDE
  637. #define EXTRUDE_MAXLENGTH 200
  638. //===========================================================================
  639. //======================== Thermal Runaway Protection =======================
  640. //===========================================================================
  641. /**
  642. * Thermal Protection provides additional protection to your printer from damage
  643. * and fire. Marlin always includes safe min and max temperature ranges which
  644. * protect against a broken or disconnected thermistor wire.
  645. *
  646. * The issue: If a thermistor falls out, it will report the much lower
  647. * temperature of the air in the room, and the the firmware will keep
  648. * the heater on.
  649. *
  650. * If you get "Thermal Runaway" or "Heating failed" errors the
  651. * details can be tuned in Configuration_adv.h
  652. */
  653. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  654. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  655. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  656. #define THERMAL_PROTECTION_COOLER // Enable thermal protection for the laser cooling
  657. //===========================================================================
  658. //============================= Mechanical Settings =========================
  659. //===========================================================================
  660. // @section machine
  661. // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
  662. // either in the usual order or reversed
  663. //#define COREXY
  664. //#define COREXZ
  665. //#define COREYZ
  666. //#define COREYX
  667. //#define COREZX
  668. //#define COREZY
  669. //#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042
  670. //#define MARKFORGED_YX
  671. // Enable for a belt style printer with endless "Z" motion
  672. //#define BELTPRINTER
  673. // Enable for Polargraph Kinematics
  674. //#define POLARGRAPH
  675. #if ENABLED(POLARGRAPH)
  676. #define POLARGRAPH_MAX_BELT_LEN 1035.0
  677. #define POLAR_SEGMENTS_PER_SECOND 5
  678. #endif
  679. //===========================================================================
  680. //============================== Endstop Settings ===========================
  681. //===========================================================================
  682. // @section homing
  683. // Specify here all the endstop connectors that are connected to any endstop or probe.
  684. // Almost all printers will be using one per axis. Probes will use one or more of the
  685. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  686. #define USE_XMIN_PLUG
  687. #define USE_YMIN_PLUG
  688. #define USE_ZMIN_PLUG
  689. //#define USE_IMIN_PLUG
  690. //#define USE_JMIN_PLUG
  691. //#define USE_KMIN_PLUG
  692. //#define USE_XMAX_PLUG
  693. //#define USE_YMAX_PLUG
  694. //#define USE_ZMAX_PLUG
  695. //#define USE_IMAX_PLUG
  696. //#define USE_JMAX_PLUG
  697. //#define USE_KMAX_PLUG
  698. // Enable pullup for all endstops to prevent a floating state
  699. #define ENDSTOPPULLUPS
  700. #if DISABLED(ENDSTOPPULLUPS)
  701. // Disable ENDSTOPPULLUPS to set pullups individually
  702. //#define ENDSTOPPULLUP_XMIN
  703. //#define ENDSTOPPULLUP_YMIN
  704. //#define ENDSTOPPULLUP_ZMIN
  705. //#define ENDSTOPPULLUP_IMIN
  706. //#define ENDSTOPPULLUP_JMIN
  707. //#define ENDSTOPPULLUP_KMIN
  708. //#define ENDSTOPPULLUP_XMAX
  709. //#define ENDSTOPPULLUP_YMAX
  710. //#define ENDSTOPPULLUP_ZMAX
  711. //#define ENDSTOPPULLUP_IMAX
  712. //#define ENDSTOPPULLUP_JMAX
  713. //#define ENDSTOPPULLUP_KMAX
  714. //#define ENDSTOPPULLUP_ZMIN_PROBE
  715. #endif
  716. // Enable pulldown for all endstops to prevent a floating state
  717. //#define ENDSTOPPULLDOWNS
  718. #if DISABLED(ENDSTOPPULLDOWNS)
  719. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  720. //#define ENDSTOPPULLDOWN_XMIN
  721. //#define ENDSTOPPULLDOWN_YMIN
  722. //#define ENDSTOPPULLDOWN_ZMIN
  723. //#define ENDSTOPPULLDOWN_IMIN
  724. //#define ENDSTOPPULLDOWN_JMIN
  725. //#define ENDSTOPPULLDOWN_KMIN
  726. //#define ENDSTOPPULLDOWN_XMAX
  727. //#define ENDSTOPPULLDOWN_YMAX
  728. //#define ENDSTOPPULLDOWN_ZMAX
  729. //#define ENDSTOPPULLDOWN_IMAX
  730. //#define ENDSTOPPULLDOWN_JMAX
  731. //#define ENDSTOPPULLDOWN_KMAX
  732. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  733. #endif
  734. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  735. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  736. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  737. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  738. #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  739. #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  740. #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  741. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  742. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  743. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  744. #define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  745. #define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  746. #define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  747. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  748. /**
  749. * Stepper Drivers
  750. *
  751. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  752. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  753. *
  754. * A4988 is assumed for unspecified drivers.
  755. *
  756. * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  757. *
  758. * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
  759. * TB6560, TB6600, TMC2100,
  760. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  761. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  762. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  763. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  764. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  765. */
  766. #define X_DRIVER_TYPE A4988
  767. #define Y_DRIVER_TYPE A4988
  768. #define Z_DRIVER_TYPE A4988
  769. //#define X2_DRIVER_TYPE A4988
  770. //#define Y2_DRIVER_TYPE A4988
  771. //#define Z2_DRIVER_TYPE A4988
  772. //#define Z3_DRIVER_TYPE A4988
  773. //#define Z4_DRIVER_TYPE A4988
  774. //#define I_DRIVER_TYPE A4988
  775. //#define J_DRIVER_TYPE A4988
  776. //#define K_DRIVER_TYPE A4988
  777. #define E0_DRIVER_TYPE A4988
  778. //#define E1_DRIVER_TYPE A4988
  779. //#define E2_DRIVER_TYPE A4988
  780. //#define E3_DRIVER_TYPE A4988
  781. //#define E4_DRIVER_TYPE A4988
  782. //#define E5_DRIVER_TYPE A4988
  783. //#define E6_DRIVER_TYPE A4988
  784. //#define E7_DRIVER_TYPE A4988
  785. // Enable this feature if all enabled endstop pins are interrupt-capable.
  786. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  787. //#define ENDSTOP_INTERRUPTS_FEATURE
  788. /**
  789. * Endstop Noise Threshold
  790. *
  791. * Enable if your probe or endstops falsely trigger due to noise.
  792. *
  793. * - Higher values may affect repeatability or accuracy of some bed probes.
  794. * - To fix noise install a 100nF ceramic capacitor in parallel with the switch.
  795. * - This feature is not required for common micro-switches mounted on PCBs
  796. * based on the Makerbot design, which already have the 100nF capacitor.
  797. *
  798. * :[2,3,4,5,6,7]
  799. */
  800. //#define ENDSTOP_NOISE_THRESHOLD 2
  801. // Check for stuck or disconnected endstops during homing moves.
  802. //#define DETECT_BROKEN_ENDSTOP
  803. //=============================================================================
  804. //============================== Movement Settings ============================
  805. //=============================================================================
  806. // @section motion
  807. /**
  808. * Default Settings
  809. *
  810. * These settings can be reset by M502
  811. *
  812. * Note that if EEPROM is enabled, saved values will override these.
  813. */
  814. /**
  815. * With this option each E stepper can have its own factors for the
  816. * following movement settings. If fewer factors are given than the
  817. * total number of extruders, the last value applies to the rest.
  818. */
  819. //#define DISTINCT_E_FACTORS
  820. /**
  821. * Default Axis Steps Per Unit (steps/mm)
  822. * Override with M92
  823. * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  824. */
  825. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
  826. /**
  827. * Default Max Feed Rate (mm/s)
  828. * Override with M203
  829. * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  830. */
  831. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  832. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  833. #if ENABLED(LIMITED_MAX_FR_EDITING)
  834. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  835. #endif
  836. /**
  837. * Default Max Acceleration (change/s) change = mm/s
  838. * (Maximum start speed for accelerated moves)
  839. * Override with M201
  840. * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  841. */
  842. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  843. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  844. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  845. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  846. #endif
  847. /**
  848. * Default Acceleration (change/s) change = mm/s
  849. * Override with M204
  850. *
  851. * M204 P Acceleration
  852. * M204 R Retract Acceleration
  853. * M204 T Travel Acceleration
  854. */
  855. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  856. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  857. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  858. /**
  859. * Default Jerk limits (mm/s)
  860. * Override with M205 X Y Z E
  861. *
  862. * "Jerk" specifies the minimum speed change that requires acceleration.
  863. * When changing speed and direction, if the difference is less than the
  864. * value set here, it may happen instantaneously.
  865. */
  866. //#define CLASSIC_JERK
  867. #if ENABLED(CLASSIC_JERK)
  868. #define DEFAULT_XJERK 10.0
  869. #define DEFAULT_YJERK 10.0
  870. #define DEFAULT_ZJERK 0.3
  871. //#define DEFAULT_IJERK 0.3
  872. //#define DEFAULT_JJERK 0.3
  873. //#define DEFAULT_KJERK 0.3
  874. //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
  875. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  876. #if ENABLED(LIMITED_JERK_EDITING)
  877. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  878. #endif
  879. #endif
  880. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  881. /**
  882. * Junction Deviation Factor
  883. *
  884. * See:
  885. * https://reprap.org/forum/read.php?1,739819
  886. * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  887. */
  888. #if DISABLED(CLASSIC_JERK)
  889. #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
  890. #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
  891. // for small segments (< 1mm) with large junction angles (> 135°).
  892. #endif
  893. /**
  894. * S-Curve Acceleration
  895. *
  896. * This option eliminates vibration during printing by fitting a Bézier
  897. * curve to move acceleration, producing much smoother direction changes.
  898. *
  899. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  900. */
  901. //#define S_CURVE_ACCELERATION
  902. //===========================================================================
  903. //============================= Z Probe Options =============================
  904. //===========================================================================
  905. // @section probes
  906. //
  907. // See https://marlinfw.org/docs/configuration/probes.html
  908. //
  909. /**
  910. * Enable this option for a probe connected to the Z-MIN pin.
  911. * The probe replaces the Z-MIN endstop and is used for Z homing.
  912. * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  913. */
  914. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  915. // Force the use of the probe for Z-axis homing
  916. //#define USE_PROBE_FOR_Z_HOMING
  917. /**
  918. * Z_MIN_PROBE_PIN
  919. *
  920. * Define this pin if the probe is not connected to Z_MIN_PIN.
  921. * If not defined the default pin for the selected MOTHERBOARD
  922. * will be used. Most of the time the default is what you want.
  923. *
  924. * - The simplest option is to use a free endstop connector.
  925. * - Use 5V for powered (usually inductive) sensors.
  926. *
  927. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  928. * - For simple switches connect...
  929. * - normally-closed switches to GND and D32.
  930. * - normally-open switches to 5V and D32.
  931. */
  932. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  933. /**
  934. * Probe Type
  935. *
  936. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  937. * Activate one of these to use Auto Bed Leveling below.
  938. */
  939. /**
  940. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  941. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  942. * or (with LCD_BED_LEVELING) the LCD controller.
  943. */
  944. //#define PROBE_MANUALLY
  945. /**
  946. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  947. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  948. */
  949. //#define FIX_MOUNTED_PROBE
  950. /**
  951. * Use the nozzle as the probe, as with a conductive
  952. * nozzle system or a piezo-electric smart effector.
  953. */
  954. //#define NOZZLE_AS_PROBE
  955. /**
  956. * Z Servo Probe, such as an endstop switch on a rotating arm.
  957. */
  958. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  959. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  960. /**
  961. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  962. */
  963. //#define BLTOUCH
  964. /**
  965. * MagLev V4 probe by MDD
  966. *
  967. * This probe is deployed and activated by powering a built-in electromagnet.
  968. */
  969. //#define MAGLEV4
  970. #if ENABLED(MAGLEV4)
  971. //#define MAGLEV_TRIGGER_PIN 11 // Set to the connected digital output
  972. #define MAGLEV_TRIGGER_DELAY 15 // Changing this risks overheating the coil
  973. #endif
  974. /**
  975. * Touch-MI Probe by hotends.fr
  976. *
  977. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  978. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  979. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  980. *
  981. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  982. * and a minimum Z_HOMING_HEIGHT of 10.
  983. */
  984. //#define TOUCH_MI_PROBE
  985. #if ENABLED(TOUCH_MI_PROBE)
  986. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  987. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  988. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  989. #endif
  990. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  991. //#define SOLENOID_PROBE
  992. // A sled-mounted probe like those designed by Charles Bell.
  993. //#define Z_PROBE_SLED
  994. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  995. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  996. //#define RACK_AND_PINION_PROBE
  997. #if ENABLED(RACK_AND_PINION_PROBE)
  998. #define Z_PROBE_DEPLOY_X X_MIN_POS
  999. #define Z_PROBE_RETRACT_X X_MAX_POS
  1000. #endif
  1001. // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
  1002. // When the pin is defined you can use M672 to set/reset the probe sensitivity.
  1003. //#define DUET_SMART_EFFECTOR
  1004. #if ENABLED(DUET_SMART_EFFECTOR)
  1005. #define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin
  1006. #endif
  1007. /**
  1008. * Use StallGuard2 to probe the bed with the nozzle.
  1009. * Requires stallGuard-capable Trinamic stepper drivers.
  1010. * CAUTION: This can damage machines with Z lead screws.
  1011. * Take extreme care when setting up this feature.
  1012. */
  1013. //#define SENSORLESS_PROBING
  1014. //
  1015. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  1016. //
  1017. /**
  1018. * Nozzle-to-Probe offsets { X, Y, Z }
  1019. *
  1020. * X and Y offset
  1021. * Use a caliper or ruler to measure the distance from the tip of
  1022. * the Nozzle to the center-point of the Probe in the X and Y axes.
  1023. *
  1024. * Z offset
  1025. * - For the Z offset use your best known value and adjust at runtime.
  1026. * - Common probes trigger below the nozzle and have negative values for Z offset.
  1027. * - Probes triggering above the nozzle height are uncommon but do exist. When using
  1028. * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES
  1029. * to avoid collisions during probing.
  1030. *
  1031. * Tune and Adjust
  1032. * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc.
  1033. * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset.
  1034. *
  1035. * Assuming the typical work area orientation:
  1036. * - Probe to RIGHT of the Nozzle has a Positive X offset
  1037. * - Probe to LEFT of the Nozzle has a Negative X offset
  1038. * - Probe in BACK of the Nozzle has a Positive Y offset
  1039. * - Probe in FRONT of the Nozzle has a Negative Y offset
  1040. *
  1041. * Some examples:
  1042. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 } // Example "1"
  1043. * #define NOZZLE_TO_PROBE_OFFSET {-10, 5, -1 } // Example "2"
  1044. * #define NOZZLE_TO_PROBE_OFFSET { 5, -5, -1 } // Example "3"
  1045. * #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 } // Example "4"
  1046. *
  1047. * +-- BACK ---+
  1048. * | [+] |
  1049. * L | 1 | R <-- Example "1" (right+, back+)
  1050. * E | 2 | I <-- Example "2" ( left-, back+)
  1051. * F |[-] N [+]| G <-- Nozzle
  1052. * T | 3 | H <-- Example "3" (right+, front-)
  1053. * | 4 | T <-- Example "4" ( left-, front-)
  1054. * | [-] |
  1055. * O-- FRONT --+
  1056. */
  1057. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  1058. // Most probes should stay away from the edges of the bed, but
  1059. // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
  1060. #define PROBING_MARGIN 10
  1061. // X and Y axis travel speed (mm/min) between probes
  1062. #define XY_PROBE_FEEDRATE (133*60)
  1063. // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  1064. #define Z_PROBE_FEEDRATE_FAST (4*60)
  1065. // Feedrate (mm/min) for the "accurate" probe of each point
  1066. #define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
  1067. /**
  1068. * Probe Activation Switch
  1069. * A switch indicating proper deployment, or an optical
  1070. * switch triggered when the carriage is near the bed.
  1071. */
  1072. //#define PROBE_ACTIVATION_SWITCH
  1073. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  1074. #define PROBE_ACTIVATION_SWITCH_STATE LOW // State indicating probe is active
  1075. //#define PROBE_ACTIVATION_SWITCH_PIN PC6 // Override default pin
  1076. #endif
  1077. /**
  1078. * Tare Probe (determine zero-point) prior to each probe.
  1079. * Useful for a strain gauge or piezo sensor that needs to factor out
  1080. * elements such as cables pulling on the carriage.
  1081. */
  1082. //#define PROBE_TARE
  1083. #if ENABLED(PROBE_TARE)
  1084. #define PROBE_TARE_TIME 200 // (ms) Time to hold tare pin
  1085. #define PROBE_TARE_DELAY 200 // (ms) Delay after tare before
  1086. #define PROBE_TARE_STATE HIGH // State to write pin for tare
  1087. //#define PROBE_TARE_PIN PA5 // Override default pin
  1088. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  1089. //#define PROBE_TARE_ONLY_WHILE_INACTIVE // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active
  1090. #endif
  1091. #endif
  1092. /**
  1093. * Probe Enable / Disable
  1094. * The probe only provides a triggered signal when enabled.
  1095. */
  1096. //#define PROBE_ENABLE_DISABLE
  1097. #if ENABLED(PROBE_ENABLE_DISABLE)
  1098. //#define PROBE_ENABLE_PIN -1 // Override the default pin here
  1099. #endif
  1100. /**
  1101. * Multiple Probing
  1102. *
  1103. * You may get improved results by probing 2 or more times.
  1104. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  1105. *
  1106. * A total of 2 does fast/slow probes with a weighted average.
  1107. * A total of 3 or more adds more slow probes, taking the average.
  1108. */
  1109. //#define MULTIPLE_PROBING 2
  1110. //#define EXTRA_PROBING 1
  1111. /**
  1112. * Z probes require clearance when deploying, stowing, and moving between
  1113. * probe points to avoid hitting the bed and other hardware.
  1114. * Servo-mounted probes require extra space for the arm to rotate.
  1115. * Inductive probes need space to keep from triggering early.
  1116. *
  1117. * Use these settings to specify the distance (mm) to raise the probe (or
  1118. * lower the bed). The values set here apply over and above any (negative)
  1119. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  1120. * Only integer values >= 1 are valid here.
  1121. *
  1122. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  1123. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  1124. */
  1125. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  1126. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  1127. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  1128. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  1129. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  1130. // For M851 give a range for adjusting the Z probe offset
  1131. #define Z_PROBE_OFFSET_RANGE_MIN -20
  1132. #define Z_PROBE_OFFSET_RANGE_MAX 20
  1133. // Enable the M48 repeatability test to test probe accuracy
  1134. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  1135. // Before deploy/stow pause for user confirmation
  1136. //#define PAUSE_BEFORE_DEPLOY_STOW
  1137. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  1138. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  1139. #endif
  1140. /**
  1141. * Enable one or more of the following if probing seems unreliable.
  1142. * Heaters and/or fans can be disabled during probing to minimize electrical
  1143. * noise. A delay can also be added to allow noise and vibration to settle.
  1144. * These options are most useful for the BLTouch probe, but may also improve
  1145. * readings with inductive probes and piezo sensors.
  1146. */
  1147. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  1148. #if ENABLED(PROBING_HEATERS_OFF)
  1149. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  1150. //#define WAIT_FOR_HOTEND // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
  1151. #endif
  1152. //#define PROBING_FANS_OFF // Turn fans off when probing
  1153. //#define PROBING_ESTEPPERS_OFF // Turn all extruder steppers off when probing
  1154. //#define PROBING_STEPPERS_OFF // Turn all steppers off (unless needed to hold position) when probing (including extruders)
  1155. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  1156. // Require minimum nozzle and/or bed temperature for probing
  1157. //#define PREHEAT_BEFORE_PROBING
  1158. #if ENABLED(PREHEAT_BEFORE_PROBING)
  1159. #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1160. #define PROBING_BED_TEMP 50
  1161. #endif
  1162. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  1163. // :{ 0:'Low', 1:'High' }
  1164. #define X_ENABLE_ON 0
  1165. #define Y_ENABLE_ON 0
  1166. #define Z_ENABLE_ON 0
  1167. #define E_ENABLE_ON 0 // For all extruders
  1168. //#define I_ENABLE_ON 0
  1169. //#define J_ENABLE_ON 0
  1170. //#define K_ENABLE_ON 0
  1171. // Disable axis steppers immediately when they're not being stepped.
  1172. // WARNING: When motors turn off there is a chance of losing position accuracy!
  1173. #define DISABLE_X false
  1174. #define DISABLE_Y false
  1175. #define DISABLE_Z false
  1176. //#define DISABLE_I false
  1177. //#define DISABLE_J false
  1178. //#define DISABLE_K false
  1179. // Turn off the display blinking that warns about possible accuracy reduction
  1180. //#define DISABLE_REDUCED_ACCURACY_WARNING
  1181. // @section extruder
  1182. #define DISABLE_E false // Disable the extruder when not stepping
  1183. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  1184. // @section machine
  1185. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  1186. #define INVERT_X_DIR false
  1187. #define INVERT_Y_DIR true
  1188. #define INVERT_Z_DIR false
  1189. //#define INVERT_I_DIR false
  1190. //#define INVERT_J_DIR false
  1191. //#define INVERT_K_DIR false
  1192. // @section extruder
  1193. // For direct drive extruder v9 set to true, for geared extruder set to false.
  1194. #define INVERT_E0_DIR false
  1195. #define INVERT_E1_DIR false
  1196. #define INVERT_E2_DIR false
  1197. #define INVERT_E3_DIR false
  1198. #define INVERT_E4_DIR false
  1199. #define INVERT_E5_DIR false
  1200. #define INVERT_E6_DIR false
  1201. #define INVERT_E7_DIR false
  1202. // @section homing
  1203. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
  1204. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
  1205. /**
  1206. * Set Z_IDLE_HEIGHT if the Z-Axis moves on its own when steppers are disabled.
  1207. * - Use a low value (i.e., Z_MIN_POS) if the nozzle falls down to the bed.
  1208. * - Use a large value (i.e., Z_MAX_POS) if the bed falls down, away from the nozzle.
  1209. */
  1210. //#define Z_IDLE_HEIGHT Z_HOME_POS
  1211. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  1212. // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
  1213. //#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
  1214. // Direction of endstops when homing; 1=MAX, -1=MIN
  1215. // :[-1,1]
  1216. #define X_HOME_DIR -1
  1217. #define Y_HOME_DIR -1
  1218. #define Z_HOME_DIR -1
  1219. //#define I_HOME_DIR -1
  1220. //#define J_HOME_DIR -1
  1221. //#define K_HOME_DIR -1
  1222. // @section machine
  1223. // The size of the printable area
  1224. #define X_BED_SIZE 200
  1225. #define Y_BED_SIZE 200
  1226. // Travel limits (mm) after homing, corresponding to endstop positions.
  1227. #define X_MIN_POS 0
  1228. #define Y_MIN_POS 0
  1229. #define Z_MIN_POS 0
  1230. #define X_MAX_POS X_BED_SIZE
  1231. #define Y_MAX_POS Y_BED_SIZE
  1232. #define Z_MAX_POS 200
  1233. //#define I_MIN_POS 0
  1234. //#define I_MAX_POS 50
  1235. //#define J_MIN_POS 0
  1236. //#define J_MAX_POS 50
  1237. //#define K_MIN_POS 0
  1238. //#define K_MAX_POS 50
  1239. /**
  1240. * Software Endstops
  1241. *
  1242. * - Prevent moves outside the set machine bounds.
  1243. * - Individual axes can be disabled, if desired.
  1244. * - X and Y only apply to Cartesian robots.
  1245. * - Use 'M211' to set software endstops on/off or report current state
  1246. */
  1247. // Min software endstops constrain movement within minimum coordinate bounds
  1248. #define MIN_SOFTWARE_ENDSTOPS
  1249. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  1250. #define MIN_SOFTWARE_ENDSTOP_X
  1251. #define MIN_SOFTWARE_ENDSTOP_Y
  1252. #define MIN_SOFTWARE_ENDSTOP_Z
  1253. #define MIN_SOFTWARE_ENDSTOP_I
  1254. #define MIN_SOFTWARE_ENDSTOP_J
  1255. #define MIN_SOFTWARE_ENDSTOP_K
  1256. #endif
  1257. // Max software endstops constrain movement within maximum coordinate bounds
  1258. #define MAX_SOFTWARE_ENDSTOPS
  1259. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  1260. #define MAX_SOFTWARE_ENDSTOP_X
  1261. #define MAX_SOFTWARE_ENDSTOP_Y
  1262. #define MAX_SOFTWARE_ENDSTOP_Z
  1263. #define MAX_SOFTWARE_ENDSTOP_I
  1264. #define MAX_SOFTWARE_ENDSTOP_J
  1265. #define MAX_SOFTWARE_ENDSTOP_K
  1266. #endif
  1267. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  1268. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  1269. #endif
  1270. /**
  1271. * Filament Runout Sensors
  1272. * Mechanical or opto endstops are used to check for the presence of filament.
  1273. *
  1274. * IMPORTANT: Runout will only trigger if Marlin is aware that a print job is running.
  1275. * Marlin knows a print job is running when:
  1276. * 1. Running a print job from media started with M24.
  1277. * 2. The Print Job Timer has been started with M75.
  1278. * 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled.
  1279. *
  1280. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  1281. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  1282. */
  1283. //#define FILAMENT_RUNOUT_SENSOR
  1284. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  1285. #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
  1286. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  1287. #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
  1288. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  1289. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  1290. //#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder.
  1291. // This is automatically enabled for MIXING_EXTRUDERs.
  1292. // Override individually if the runout sensors vary
  1293. //#define FIL_RUNOUT1_STATE LOW
  1294. //#define FIL_RUNOUT1_PULLUP
  1295. //#define FIL_RUNOUT1_PULLDOWN
  1296. //#define FIL_RUNOUT2_STATE LOW
  1297. //#define FIL_RUNOUT2_PULLUP
  1298. //#define FIL_RUNOUT2_PULLDOWN
  1299. //#define FIL_RUNOUT3_STATE LOW
  1300. //#define FIL_RUNOUT3_PULLUP
  1301. //#define FIL_RUNOUT3_PULLDOWN
  1302. //#define FIL_RUNOUT4_STATE LOW
  1303. //#define FIL_RUNOUT4_PULLUP
  1304. //#define FIL_RUNOUT4_PULLDOWN
  1305. //#define FIL_RUNOUT5_STATE LOW
  1306. //#define FIL_RUNOUT5_PULLUP
  1307. //#define FIL_RUNOUT5_PULLDOWN
  1308. //#define FIL_RUNOUT6_STATE LOW
  1309. //#define FIL_RUNOUT6_PULLUP
  1310. //#define FIL_RUNOUT6_PULLDOWN
  1311. //#define FIL_RUNOUT7_STATE LOW
  1312. //#define FIL_RUNOUT7_PULLUP
  1313. //#define FIL_RUNOUT7_PULLDOWN
  1314. //#define FIL_RUNOUT8_STATE LOW
  1315. //#define FIL_RUNOUT8_PULLUP
  1316. //#define FIL_RUNOUT8_PULLDOWN
  1317. // Commands to execute on filament runout.
  1318. // With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
  1319. // NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
  1320. #define FILAMENT_RUNOUT_SCRIPT "M600"
  1321. // After a runout is detected, continue printing this length of filament
  1322. // before executing the runout script. Useful for a sensor at the end of
  1323. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  1324. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  1325. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  1326. // Enable this option to use an encoder disc that toggles the runout pin
  1327. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  1328. // large enough to avoid false positives.)
  1329. //#define FILAMENT_MOTION_SENSOR
  1330. #endif
  1331. #endif
  1332. //===========================================================================
  1333. //=============================== Bed Leveling ==============================
  1334. //===========================================================================
  1335. // @section calibrate
  1336. /**
  1337. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  1338. * and behavior of G29 will change depending on your selection.
  1339. *
  1340. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  1341. *
  1342. * - AUTO_BED_LEVELING_3POINT
  1343. * Probe 3 arbitrary points on the bed (that aren't collinear)
  1344. * You specify the XY coordinates of all 3 points.
  1345. * The result is a single tilted plane. Best for a flat bed.
  1346. *
  1347. * - AUTO_BED_LEVELING_LINEAR
  1348. * Probe several points in a grid.
  1349. * You specify the rectangle and the density of sample points.
  1350. * The result is a single tilted plane. Best for a flat bed.
  1351. *
  1352. * - AUTO_BED_LEVELING_BILINEAR
  1353. * Probe several points in a grid.
  1354. * You specify the rectangle and the density of sample points.
  1355. * The result is a mesh, best for large or uneven beds.
  1356. *
  1357. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1358. * A comprehensive bed leveling system combining the features and benefits
  1359. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1360. * Validation and Mesh Editing systems.
  1361. *
  1362. * - MESH_BED_LEVELING
  1363. * Probe a grid manually
  1364. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1365. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1366. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1367. * With an LCD controller the process is guided step-by-step.
  1368. */
  1369. //#define AUTO_BED_LEVELING_3POINT
  1370. //#define AUTO_BED_LEVELING_LINEAR
  1371. //#define AUTO_BED_LEVELING_BILINEAR
  1372. //#define AUTO_BED_LEVELING_UBL
  1373. //#define MESH_BED_LEVELING
  1374. /**
  1375. * Normally G28 leaves leveling disabled on completion. Enable one of
  1376. * these options to restore the prior leveling state or to always enable
  1377. * leveling immediately after G28.
  1378. */
  1379. //#define RESTORE_LEVELING_AFTER_G28
  1380. //#define ENABLE_LEVELING_AFTER_G28
  1381. /**
  1382. * Auto-leveling needs preheating
  1383. */
  1384. //#define PREHEAT_BEFORE_LEVELING
  1385. #if ENABLED(PREHEAT_BEFORE_LEVELING)
  1386. #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1387. #define LEVELING_BED_TEMP 50
  1388. #endif
  1389. /**
  1390. * Enable detailed logging of G28, G29, M48, etc.
  1391. * Turn on with the command 'M111 S32'.
  1392. * NOTE: Requires a lot of PROGMEM!
  1393. */
  1394. //#define DEBUG_LEVELING_FEATURE
  1395. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, PROBE_MANUALLY)
  1396. // Set a height for the start of manual adjustment
  1397. #define MANUAL_PROBE_START_Z 0.2 // (mm) Comment out to use the last-measured height
  1398. #endif
  1399. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1400. // Gradually reduce leveling correction until a set height is reached,
  1401. // at which point movement will be level to the machine's XY plane.
  1402. // The height can be set with M420 Z<height>
  1403. #define ENABLE_LEVELING_FADE_HEIGHT
  1404. #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
  1405. #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
  1406. #endif
  1407. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1408. // split up moves into short segments like a Delta. This follows the
  1409. // contours of the bed more closely than edge-to-edge straight moves.
  1410. #define SEGMENT_LEVELED_MOVES
  1411. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1412. /**
  1413. * Enable the G26 Mesh Validation Pattern tool.
  1414. */
  1415. //#define G26_MESH_VALIDATION
  1416. #if ENABLED(G26_MESH_VALIDATION)
  1417. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1418. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
  1419. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26.
  1420. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26.
  1421. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves.
  1422. #define G26_XY_FEEDRATE_TRAVEL 100 // (mm/s) Feedrate for G26 XY travel moves.
  1423. #define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
  1424. #endif
  1425. #endif
  1426. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1427. // Set the number of grid points per dimension.
  1428. #define GRID_MAX_POINTS_X 3
  1429. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1430. // Probe along the Y axis, advancing X after each column
  1431. //#define PROBE_Y_FIRST
  1432. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1433. // Beyond the probed grid, continue the implied tilt?
  1434. // Default is to maintain the height of the nearest edge.
  1435. //#define EXTRAPOLATE_BEYOND_GRID
  1436. //
  1437. // Experimental Subdivision of the grid by Catmull-Rom method.
  1438. // Synthesizes intermediate points to produce a more detailed mesh.
  1439. //
  1440. //#define ABL_BILINEAR_SUBDIVISION
  1441. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1442. // Number of subdivisions between probe points
  1443. #define BILINEAR_SUBDIVISIONS 3
  1444. #endif
  1445. #endif
  1446. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1447. //===========================================================================
  1448. //========================= Unified Bed Leveling ============================
  1449. //===========================================================================
  1450. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1451. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1452. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1453. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1454. //#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
  1455. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1456. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1457. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1458. // as the Z-Height correction value.
  1459. //#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
  1460. #elif ENABLED(MESH_BED_LEVELING)
  1461. //===========================================================================
  1462. //=================================== Mesh ==================================
  1463. //===========================================================================
  1464. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1465. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1466. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1467. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1468. #endif // BED_LEVELING
  1469. /**
  1470. * Add a bed leveling sub-menu for ABL or MBL.
  1471. * Include a guided procedure if manual probing is enabled.
  1472. */
  1473. //#define LCD_BED_LEVELING
  1474. #if ENABLED(LCD_BED_LEVELING)
  1475. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1476. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1477. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1478. #endif
  1479. // Add a menu item to move between bed corners for manual bed adjustment
  1480. //#define LEVEL_BED_CORNERS
  1481. #if ENABLED(LEVEL_BED_CORNERS)
  1482. #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
  1483. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1484. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
  1485. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1486. //#define LEVEL_CORNERS_USE_PROBE
  1487. #if ENABLED(LEVEL_CORNERS_USE_PROBE)
  1488. #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
  1489. #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
  1490. //#define LEVEL_CORNERS_AUDIO_FEEDBACK
  1491. #endif
  1492. /**
  1493. * Corner Leveling Order
  1494. *
  1495. * Set 2 or 4 points. When 2 points are given, the 3rd is the center of the opposite edge.
  1496. *
  1497. * LF Left-Front RF Right-Front
  1498. * LB Left-Back RB Right-Back
  1499. *
  1500. * Examples:
  1501. *
  1502. * Default {LF,RB,LB,RF} {LF,RF} {LB,LF}
  1503. * LB --------- RB LB --------- RB LB --------- RB LB --------- RB
  1504. * | 4 3 | | 3 2 | | <3> | | 1 |
  1505. * | | | | | | | <3>|
  1506. * | 1 2 | | 1 4 | | 1 2 | | 2 |
  1507. * LF --------- RF LF --------- RF LF --------- RF LF --------- RF
  1508. */
  1509. #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB }
  1510. #endif
  1511. /**
  1512. * Commands to execute at the end of G29 probing.
  1513. * Useful to retract or move the Z probe out of the way.
  1514. */
  1515. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1516. // @section homing
  1517. // The center of the bed is at (X=0, Y=0)
  1518. //#define BED_CENTER_AT_0_0
  1519. // Manually set the home position. Leave these undefined for automatic settings.
  1520. // For DELTA this is the top-center of the Cartesian print volume.
  1521. //#define MANUAL_X_HOME_POS 0
  1522. //#define MANUAL_Y_HOME_POS 0
  1523. //#define MANUAL_Z_HOME_POS 0
  1524. //#define MANUAL_I_HOME_POS 0
  1525. //#define MANUAL_J_HOME_POS 0
  1526. //#define MANUAL_K_HOME_POS 0
  1527. /**
  1528. * Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1529. *
  1530. * - Moves the Z probe (or nozzle) to a defined XY point before Z homing.
  1531. * - Allows Z homing only when XY positions are known and trusted.
  1532. * - If stepper drivers sleep, XY homing may be required again before Z homing.
  1533. */
  1534. //#define Z_SAFE_HOMING
  1535. #if ENABLED(Z_SAFE_HOMING)
  1536. #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
  1537. #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
  1538. #endif
  1539. // Homing speeds (mm/min)
  1540. #define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
  1541. // Validate that endstops are triggered on homing moves
  1542. #define VALIDATE_HOMING_ENDSTOPS
  1543. // @section calibrate
  1544. /**
  1545. * Bed Skew Compensation
  1546. *
  1547. * This feature corrects for misalignment in the XYZ axes.
  1548. *
  1549. * Take the following steps to get the bed skew in the XY plane:
  1550. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1551. * 2. For XY_DIAG_AC measure the diagonal A to C
  1552. * 3. For XY_DIAG_BD measure the diagonal B to D
  1553. * 4. For XY_SIDE_AD measure the edge A to D
  1554. *
  1555. * Marlin automatically computes skew factors from these measurements.
  1556. * Skew factors may also be computed and set manually:
  1557. *
  1558. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1559. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1560. *
  1561. * If desired, follow the same procedure for XZ and YZ.
  1562. * Use these diagrams for reference:
  1563. *
  1564. * Y Z Z
  1565. * ^ B-------C ^ B-------C ^ B-------C
  1566. * | / / | / / | / /
  1567. * | / / | / / | / /
  1568. * | A-------D | A-------D | A-------D
  1569. * +-------------->X +-------------->X +-------------->Y
  1570. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1571. */
  1572. //#define SKEW_CORRECTION
  1573. #if ENABLED(SKEW_CORRECTION)
  1574. // Input all length measurements here:
  1575. #define XY_DIAG_AC 282.8427124746
  1576. #define XY_DIAG_BD 282.8427124746
  1577. #define XY_SIDE_AD 200
  1578. // Or, set the default skew factors directly here
  1579. // to override the above measurements:
  1580. #define XY_SKEW_FACTOR 0.0
  1581. //#define SKEW_CORRECTION_FOR_Z
  1582. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1583. #define XZ_DIAG_AC 282.8427124746
  1584. #define XZ_DIAG_BD 282.8427124746
  1585. #define YZ_DIAG_AC 282.8427124746
  1586. #define YZ_DIAG_BD 282.8427124746
  1587. #define YZ_SIDE_AD 200
  1588. #define XZ_SKEW_FACTOR 0.0
  1589. #define YZ_SKEW_FACTOR 0.0
  1590. #endif
  1591. // Enable this option for M852 to set skew at runtime
  1592. //#define SKEW_CORRECTION_GCODE
  1593. #endif
  1594. //=============================================================================
  1595. //============================= Additional Features ===========================
  1596. //=============================================================================
  1597. // @section extras
  1598. /**
  1599. * EEPROM
  1600. *
  1601. * Persistent storage to preserve configurable settings across reboots.
  1602. *
  1603. * M500 - Store settings to EEPROM.
  1604. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1605. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1606. */
  1607. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1608. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1609. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1610. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
  1611. #if ENABLED(EEPROM_SETTINGS)
  1612. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1613. //#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
  1614. #endif
  1615. //
  1616. // Host Keepalive
  1617. //
  1618. // When enabled Marlin will send a busy status message to the host
  1619. // every couple of seconds when it can't accept commands.
  1620. //
  1621. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1622. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1623. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1624. //
  1625. // G20/G21 Inch mode support
  1626. //
  1627. //#define INCH_MODE_SUPPORT
  1628. //
  1629. // M149 Set temperature units support
  1630. //
  1631. //#define TEMPERATURE_UNITS_SUPPORT
  1632. // @section temperature
  1633. //
  1634. // Preheat Constants - Up to 5 are supported without changes
  1635. //
  1636. #define PREHEAT_1_LABEL "PLA"
  1637. #define PREHEAT_1_TEMP_HOTEND 180
  1638. #define PREHEAT_1_TEMP_BED 70
  1639. #define PREHEAT_1_TEMP_CHAMBER 35
  1640. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1641. #define PREHEAT_2_LABEL "ABS"
  1642. #define PREHEAT_2_TEMP_HOTEND 240
  1643. #define PREHEAT_2_TEMP_BED 110
  1644. #define PREHEAT_2_TEMP_CHAMBER 35
  1645. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1646. /**
  1647. * Nozzle Park
  1648. *
  1649. * Park the nozzle at the given XYZ position on idle or G27.
  1650. *
  1651. * The "P" parameter controls the action applied to the Z axis:
  1652. *
  1653. * P0 (Default) If Z is below park Z raise the nozzle.
  1654. * P1 Raise the nozzle always to Z-park height.
  1655. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1656. */
  1657. //#define NOZZLE_PARK_FEATURE
  1658. #if ENABLED(NOZZLE_PARK_FEATURE)
  1659. // Specify a park position as { X, Y, Z_raise }
  1660. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1661. //#define NOZZLE_PARK_X_ONLY // X move only is required to park
  1662. //#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
  1663. #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
  1664. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1665. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1666. #endif
  1667. /**
  1668. * Clean Nozzle Feature -- EXPERIMENTAL
  1669. *
  1670. * Adds the G12 command to perform a nozzle cleaning process.
  1671. *
  1672. * Parameters:
  1673. * P Pattern
  1674. * S Strokes / Repetitions
  1675. * T Triangles (P1 only)
  1676. *
  1677. * Patterns:
  1678. * P0 Straight line (default). This process requires a sponge type material
  1679. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1680. * between the start / end points.
  1681. *
  1682. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1683. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1684. * Zig-zags are done in whichever is the narrower dimension.
  1685. * For example, "G12 P1 S1 T3" will execute:
  1686. *
  1687. * --
  1688. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1689. * | | / \ / \ / \ |
  1690. * A | | / \ / \ / \ |
  1691. * | | / \ / \ / \ |
  1692. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1693. * -- +--------------------------------+
  1694. * |________|_________|_________|
  1695. * T1 T2 T3
  1696. *
  1697. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1698. * "R" specifies the radius. "S" specifies the stroke count.
  1699. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1700. *
  1701. * Caveats: The ending Z should be the same as starting Z.
  1702. * Attention: EXPERIMENTAL. G-code arguments may change.
  1703. */
  1704. //#define NOZZLE_CLEAN_FEATURE
  1705. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1706. // Default number of pattern repetitions
  1707. #define NOZZLE_CLEAN_STROKES 12
  1708. // Default number of triangles
  1709. #define NOZZLE_CLEAN_TRIANGLES 3
  1710. // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
  1711. // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
  1712. #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } }
  1713. #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }
  1714. // Circular pattern radius
  1715. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1716. // Circular pattern circle fragments number
  1717. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1718. // Middle point of circle
  1719. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1720. // Move the nozzle to the initial position after cleaning
  1721. #define NOZZLE_CLEAN_GOBACK
  1722. // For a purge/clean station that's always at the gantry height (thus no Z move)
  1723. //#define NOZZLE_CLEAN_NO_Z
  1724. // For a purge/clean station mounted on the X axis
  1725. //#define NOZZLE_CLEAN_NO_Y
  1726. // Require a minimum hotend temperature for cleaning
  1727. #define NOZZLE_CLEAN_MIN_TEMP 170
  1728. //#define NOZZLE_CLEAN_HEATUP // Heat up the nozzle instead of skipping wipe
  1729. // Explicit wipe G-code script applies to a G12 with no arguments.
  1730. //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0"
  1731. #endif
  1732. /**
  1733. * Print Job Timer
  1734. *
  1735. * Automatically start and stop the print job timer on M104/M109/M140/M190/M141/M191.
  1736. * The print job timer will only be stopped if the bed/chamber target temp is
  1737. * below BED_MINTEMP/CHAMBER_MINTEMP.
  1738. *
  1739. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1740. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1741. * M140 (bed, no wait) - high temp = none, low temp = stop timer
  1742. * M190 (bed, wait) - high temp = start timer, low temp = none
  1743. * M141 (chamber, no wait) - high temp = none, low temp = stop timer
  1744. * M191 (chamber, wait) - high temp = start timer, low temp = none
  1745. *
  1746. * For M104/M109, high temp is anything over EXTRUDE_MINTEMP / 2.
  1747. * For M140/M190, high temp is anything over BED_MINTEMP.
  1748. * For M141/M191, high temp is anything over CHAMBER_MINTEMP.
  1749. *
  1750. * The timer can also be controlled with the following commands:
  1751. *
  1752. * M75 - Start the print job timer
  1753. * M76 - Pause the print job timer
  1754. * M77 - Stop the print job timer
  1755. */
  1756. #define PRINTJOB_TIMER_AUTOSTART
  1757. /**
  1758. * Print Counter
  1759. *
  1760. * Track statistical data such as:
  1761. *
  1762. * - Total print jobs
  1763. * - Total successful print jobs
  1764. * - Total failed print jobs
  1765. * - Total time printing
  1766. *
  1767. * View the current statistics with M78.
  1768. */
  1769. //#define PRINTCOUNTER
  1770. #if ENABLED(PRINTCOUNTER)
  1771. #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
  1772. #endif
  1773. /**
  1774. * Password
  1775. *
  1776. * Set a numerical password for the printer which can be requested:
  1777. *
  1778. * - When the printer boots up
  1779. * - Upon opening the 'Print from Media' Menu
  1780. * - When SD printing is completed or aborted
  1781. *
  1782. * The following G-codes can be used:
  1783. *
  1784. * M510 - Lock Printer. Blocks all commands except M511.
  1785. * M511 - Unlock Printer.
  1786. * M512 - Set, Change and Remove Password.
  1787. *
  1788. * If you forget the password and get locked out you'll need to re-flash
  1789. * the firmware with the feature disabled, reset EEPROM, and (optionally)
  1790. * re-flash the firmware again with this feature enabled.
  1791. */
  1792. //#define PASSWORD_FEATURE
  1793. #if ENABLED(PASSWORD_FEATURE)
  1794. #define PASSWORD_LENGTH 4 // (#) Number of digits (1-9). 3 or 4 is recommended
  1795. #define PASSWORD_ON_STARTUP
  1796. #define PASSWORD_UNLOCK_GCODE // Unlock with the M511 P<password> command. Disable to prevent brute-force attack.
  1797. #define PASSWORD_CHANGE_GCODE // Change the password with M512 P<old> S<new>.
  1798. //#define PASSWORD_ON_SD_PRINT_MENU // This does not prevent gcodes from running
  1799. //#define PASSWORD_AFTER_SD_PRINT_END
  1800. //#define PASSWORD_AFTER_SD_PRINT_ABORT
  1801. //#include "Configuration_Secure.h" // External file with PASSWORD_DEFAULT_VALUE
  1802. #endif
  1803. //=============================================================================
  1804. //============================= LCD and SD support ============================
  1805. //=============================================================================
  1806. // @section lcd
  1807. /**
  1808. * LCD LANGUAGE
  1809. *
  1810. * Select the language to display on the LCD. These languages are available:
  1811. *
  1812. * en, an, bg, ca, cz, da, de, el, el_CY, es, eu, fi, fr, gl, hr, hu, it,
  1813. * jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, sv, tr, uk, vi, zh_CN, zh_TW
  1814. *
  1815. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek (Greece)', 'el_CY':'Greek (Cyprus)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'sv':'Swedish', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)' }
  1816. */
  1817. #define LCD_LANGUAGE en
  1818. /**
  1819. * LCD Character Set
  1820. *
  1821. * Note: This option is NOT applicable to Graphical Displays.
  1822. *
  1823. * All character-based LCDs provide ASCII plus one of these
  1824. * language extensions:
  1825. *
  1826. * - JAPANESE ... the most common
  1827. * - WESTERN ... with more accented characters
  1828. * - CYRILLIC ... for the Russian language
  1829. *
  1830. * To determine the language extension installed on your controller:
  1831. *
  1832. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1833. * - Click the controller to view the LCD menu
  1834. * - The LCD will display Japanese, Western, or Cyrillic text
  1835. *
  1836. * See https://marlinfw.org/docs/development/lcd_language.html
  1837. *
  1838. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1839. */
  1840. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1841. /**
  1842. * Info Screen Style (0:Classic, 1:Průša)
  1843. *
  1844. * :[0:'Classic', 1:'Průša']
  1845. */
  1846. #define LCD_INFO_SCREEN_STYLE 0
  1847. /**
  1848. * SD CARD
  1849. *
  1850. * SD Card support is disabled by default. If your controller has an SD slot,
  1851. * you must uncomment the following option or it won't work.
  1852. */
  1853. //#define SDSUPPORT
  1854. /**
  1855. * SD CARD: ENABLE CRC
  1856. *
  1857. * Use CRC checks and retries on the SD communication.
  1858. */
  1859. //#define SD_CHECK_AND_RETRY
  1860. /**
  1861. * LCD Menu Items
  1862. *
  1863. * Disable all menus and only display the Status Screen, or
  1864. * just remove some extraneous menu items to recover space.
  1865. */
  1866. //#define NO_LCD_MENUS
  1867. //#define SLIM_LCD_MENUS
  1868. //
  1869. // ENCODER SETTINGS
  1870. //
  1871. // This option overrides the default number of encoder pulses needed to
  1872. // produce one step. Should be increased for high-resolution encoders.
  1873. //
  1874. //#define ENCODER_PULSES_PER_STEP 4
  1875. //
  1876. // Use this option to override the number of step signals required to
  1877. // move between next/prev menu items.
  1878. //
  1879. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1880. /**
  1881. * Encoder Direction Options
  1882. *
  1883. * Test your encoder's behavior first with both options disabled.
  1884. *
  1885. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1886. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1887. * Reversed Value Editing only? Enable BOTH options.
  1888. */
  1889. //
  1890. // This option reverses the encoder direction everywhere.
  1891. //
  1892. // Set this option if CLOCKWISE causes values to DECREASE
  1893. //
  1894. //#define REVERSE_ENCODER_DIRECTION
  1895. //
  1896. // This option reverses the encoder direction for navigating LCD menus.
  1897. //
  1898. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1899. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1900. //
  1901. //#define REVERSE_MENU_DIRECTION
  1902. //
  1903. // This option reverses the encoder direction for Select Screen.
  1904. //
  1905. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1906. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1907. //
  1908. //#define REVERSE_SELECT_DIRECTION
  1909. //
  1910. // Individual Axis Homing
  1911. //
  1912. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1913. //
  1914. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1915. //#define INDIVIDUAL_AXIS_HOMING_SUBMENU
  1916. //
  1917. // SPEAKER/BUZZER
  1918. //
  1919. // If you have a speaker that can produce tones, enable it here.
  1920. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1921. //
  1922. //#define SPEAKER
  1923. //
  1924. // The duration and frequency for the UI feedback sound.
  1925. // Set these to 0 to disable audio feedback in the LCD menus.
  1926. //
  1927. // Note: Test audio output with the G-Code:
  1928. // M300 S<frequency Hz> P<duration ms>
  1929. //
  1930. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1931. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1932. //=============================================================================
  1933. //======================== LCD / Controller Selection =========================
  1934. //======================== (Character-based LCDs) =========================
  1935. //=============================================================================
  1936. //
  1937. // RepRapDiscount Smart Controller.
  1938. // https://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1939. //
  1940. // Note: Usually sold with a white PCB.
  1941. //
  1942. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1943. //
  1944. // GT2560 (YHCB2004) LCD Display
  1945. //
  1946. // Requires Testato, Koepel softwarewire library and
  1947. // Andriy Golovnya's LiquidCrystal_AIP31068 library.
  1948. //
  1949. //#define YHCB2004
  1950. //
  1951. // Original RADDS LCD Display+Encoder+SDCardReader
  1952. // http://doku.radds.org/dokumentation/lcd-display/
  1953. //
  1954. //#define RADDS_DISPLAY
  1955. //
  1956. // ULTIMAKER Controller.
  1957. //
  1958. //#define ULTIMAKERCONTROLLER
  1959. //
  1960. // ULTIPANEL as seen on Thingiverse.
  1961. //
  1962. //#define ULTIPANEL
  1963. //
  1964. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1965. // https://reprap.org/wiki/PanelOne
  1966. //
  1967. //#define PANEL_ONE
  1968. //
  1969. // GADGETS3D G3D LCD/SD Controller
  1970. // https://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1971. //
  1972. // Note: Usually sold with a blue PCB.
  1973. //
  1974. //#define G3D_PANEL
  1975. //
  1976. // RigidBot Panel V1.0
  1977. // http://www.inventapart.com/
  1978. //
  1979. //#define RIGIDBOT_PANEL
  1980. //
  1981. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1982. // https://www.aliexpress.com/item/32765887917.html
  1983. //
  1984. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1985. //
  1986. // ANET and Tronxy 20x4 Controller
  1987. //
  1988. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1989. // This LCD is known to be susceptible to electrical interference
  1990. // which scrambles the display. Pressing any button clears it up.
  1991. // This is a LCD2004 display with 5 analog buttons.
  1992. //
  1993. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1994. //
  1995. //#define ULTRA_LCD
  1996. //=============================================================================
  1997. //======================== LCD / Controller Selection =========================
  1998. //===================== (I2C and Shift-Register LCDs) =====================
  1999. //=============================================================================
  2000. //
  2001. // CONTROLLER TYPE: I2C
  2002. //
  2003. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  2004. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  2005. //
  2006. //
  2007. // Elefu RA Board Control Panel
  2008. // http://www.elefu.com/index.php?route=product/product&product_id=53
  2009. //
  2010. //#define RA_CONTROL_PANEL
  2011. //
  2012. // Sainsmart (YwRobot) LCD Displays
  2013. //
  2014. // These require F.Malpartida's LiquidCrystal_I2C library
  2015. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  2016. //
  2017. //#define LCD_SAINSMART_I2C_1602
  2018. //#define LCD_SAINSMART_I2C_2004
  2019. //
  2020. // Generic LCM1602 LCD adapter
  2021. //
  2022. //#define LCM1602
  2023. //
  2024. // PANELOLU2 LCD with status LEDs,
  2025. // separate encoder and click inputs.
  2026. //
  2027. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  2028. // For more info: https://github.com/lincomatic/LiquidTWI2
  2029. //
  2030. // Note: The PANELOLU2 encoder click input can either be directly connected to
  2031. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  2032. //
  2033. //#define LCD_I2C_PANELOLU2
  2034. //
  2035. // Panucatt VIKI LCD with status LEDs,
  2036. // integrated click & L/R/U/D buttons, separate encoder inputs.
  2037. //
  2038. //#define LCD_I2C_VIKI
  2039. //
  2040. // CONTROLLER TYPE: Shift register panels
  2041. //
  2042. //
  2043. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  2044. // LCD configuration: https://reprap.org/wiki/SAV_3D_LCD
  2045. //
  2046. //#define SAV_3DLCD
  2047. //
  2048. // 3-wire SR LCD with strobe using 74HC4094
  2049. // https://github.com/mikeshub/SailfishLCD
  2050. // Uses the code directly from Sailfish
  2051. //
  2052. //#define FF_INTERFACEBOARD
  2053. //
  2054. // TFT GLCD Panel with Marlin UI
  2055. // Panel connected to main board by SPI or I2C interface.
  2056. // See https://github.com/Serhiy-K/TFTGLCDAdapter
  2057. //
  2058. //#define TFTGLCD_PANEL_SPI
  2059. //#define TFTGLCD_PANEL_I2C
  2060. //=============================================================================
  2061. //======================= LCD / Controller Selection =======================
  2062. //========================= (Graphical LCDs) ========================
  2063. //=============================================================================
  2064. //
  2065. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  2066. //
  2067. // IMPORTANT: The U8glib library is required for Graphical Display!
  2068. // https://github.com/olikraus/U8glib_Arduino
  2069. //
  2070. // NOTE: If the LCD is unresponsive you may need to reverse the plugs.
  2071. //
  2072. //
  2073. // RepRapDiscount FULL GRAPHIC Smart Controller
  2074. // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  2075. //
  2076. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  2077. //
  2078. // K.3D Full Graphic Smart Controller
  2079. //
  2080. //#define K3D_FULL_GRAPHIC_SMART_CONTROLLER
  2081. //
  2082. // ReprapWorld Graphical LCD
  2083. // https://reprapworld.com/?products_details&products_id/1218
  2084. //
  2085. //#define REPRAPWORLD_GRAPHICAL_LCD
  2086. //
  2087. // Activate one of these if you have a Panucatt Devices
  2088. // Viki 2.0 or mini Viki with Graphic LCD
  2089. // https://www.panucatt.com
  2090. //
  2091. //#define VIKI2
  2092. //#define miniVIKI
  2093. //
  2094. // Alfawise Ex8 printer LCD marked as WYH L12864 COG
  2095. //
  2096. //#define WYH_L12864
  2097. //
  2098. // MakerLab Mini Panel with graphic
  2099. // controller and SD support - https://reprap.org/wiki/Mini_panel
  2100. //
  2101. //#define MINIPANEL
  2102. //
  2103. // MaKr3d Makr-Panel with graphic controller and SD support.
  2104. // https://reprap.org/wiki/MaKr3d_MaKrPanel
  2105. //
  2106. //#define MAKRPANEL
  2107. //
  2108. // Adafruit ST7565 Full Graphic Controller.
  2109. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  2110. //
  2111. //#define ELB_FULL_GRAPHIC_CONTROLLER
  2112. //
  2113. // BQ LCD Smart Controller shipped by
  2114. // default with the BQ Hephestos 2 and Witbox 2.
  2115. //
  2116. //#define BQ_LCD_SMART_CONTROLLER
  2117. //
  2118. // Cartesio UI
  2119. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  2120. //
  2121. //#define CARTESIO_UI
  2122. //
  2123. // LCD for Melzi Card with Graphical LCD
  2124. //
  2125. //#define LCD_FOR_MELZI
  2126. //
  2127. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  2128. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  2129. //
  2130. //#define ULTI_CONTROLLER
  2131. //
  2132. // MKS MINI12864 with graphic controller and SD support
  2133. // https://reprap.org/wiki/MKS_MINI_12864
  2134. //
  2135. //#define MKS_MINI_12864
  2136. //
  2137. // MKS MINI12864 V3 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
  2138. //
  2139. //#define MKS_MINI_12864_V3
  2140. //
  2141. // MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout.
  2142. // https://www.aliexpress.com/item/33018110072.html
  2143. //
  2144. //#define MKS_LCD12864A
  2145. //#define MKS_LCD12864B
  2146. //
  2147. // FYSETC variant of the MINI12864 graphic controller with SD support
  2148. // https://wiki.fysetc.com/Mini12864_Panel/
  2149. //
  2150. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  2151. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  2152. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  2153. //#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight
  2154. //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight.
  2155. //
  2156. // BigTreeTech Mini 12864 V1.0 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
  2157. //
  2158. //#define BTT_MINI_12864_V1
  2159. //
  2160. // Factory display for Creality CR-10
  2161. // https://www.aliexpress.com/item/32833148327.html
  2162. //
  2163. // This is RAMPS-compatible using a single 10-pin connector.
  2164. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  2165. //
  2166. //#define CR10_STOCKDISPLAY
  2167. //
  2168. // Ender-2 OEM display, a variant of the MKS_MINI_12864
  2169. //
  2170. //#define ENDER2_STOCKDISPLAY
  2171. //
  2172. // ANET and Tronxy Graphical Controller
  2173. //
  2174. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  2175. // A clone of the RepRapDiscount full graphics display but with
  2176. // different pins/wiring (see pins_ANET_10.h). Enable one of these.
  2177. //
  2178. //#define ANET_FULL_GRAPHICS_LCD
  2179. //#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING
  2180. //
  2181. // AZSMZ 12864 LCD with SD
  2182. // https://www.aliexpress.com/item/32837222770.html
  2183. //
  2184. //#define AZSMZ_12864
  2185. //
  2186. // Silvergate GLCD controller
  2187. // https://github.com/android444/Silvergate
  2188. //
  2189. //#define SILVER_GATE_GLCD_CONTROLLER
  2190. //=============================================================================
  2191. //============================== OLED Displays ==============================
  2192. //=============================================================================
  2193. //
  2194. // SSD1306 OLED full graphics generic display
  2195. //
  2196. //#define U8GLIB_SSD1306
  2197. //
  2198. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  2199. //
  2200. //#define SAV_3DGLCD
  2201. #if ENABLED(SAV_3DGLCD)
  2202. #define U8GLIB_SSD1306
  2203. //#define U8GLIB_SH1106
  2204. #endif
  2205. //
  2206. // TinyBoy2 128x64 OLED / Encoder Panel
  2207. //
  2208. //#define OLED_PANEL_TINYBOY2
  2209. //
  2210. // MKS OLED 1.3" 128×64 Full Graphics Controller
  2211. // https://reprap.org/wiki/MKS_12864OLED
  2212. //
  2213. // Tiny, but very sharp OLED display
  2214. //
  2215. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  2216. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  2217. //
  2218. // Zonestar OLED 128×64 Full Graphics Controller
  2219. //
  2220. //#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller
  2221. //#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default)
  2222. //#define ZONESTAR_12864OLED_SSD1306 // 0.96" OLED with SSD1306 controller
  2223. //
  2224. // Einstart S OLED SSD1306
  2225. //
  2226. //#define U8GLIB_SH1106_EINSTART
  2227. //
  2228. // Overlord OLED display/controller with i2c buzzer and LEDs
  2229. //
  2230. //#define OVERLORD_OLED
  2231. //
  2232. // FYSETC OLED 2.42" 128×64 Full Graphics Controller with WS2812 RGB
  2233. // Where to find : https://www.aliexpress.com/item/4000345255731.html
  2234. //#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller
  2235. //
  2236. // K.3D SSD1309 OLED 2.42" 128×64 Full Graphics Controller
  2237. //
  2238. //#define K3D_242_OLED_CONTROLLER // Software SPI
  2239. //=============================================================================
  2240. //========================== Extensible UI Displays ===========================
  2241. //=============================================================================
  2242. //
  2243. // DGUS Touch Display with DWIN OS. (Choose one.)
  2244. // ORIGIN : https://www.aliexpress.com/item/32993409517.html
  2245. // FYSETC : https://www.aliexpress.com/item/32961471929.html
  2246. // MKS : https://www.aliexpress.com/item/1005002008179262.html
  2247. //
  2248. // Flash display with DGUS Displays for Marlin:
  2249. // - Format the SD card to FAT32 with an allocation size of 4kb.
  2250. // - Download files as specified for your type of display.
  2251. // - Plug the microSD card into the back of the display.
  2252. // - Boot the display and wait for the update to complete.
  2253. //
  2254. // ORIGIN (Marlin DWIN_SET)
  2255. // - Download https://github.com/coldtobi/Marlin_DGUS_Resources
  2256. // - Copy the downloaded DWIN_SET folder to the SD card.
  2257. //
  2258. // FYSETC (Supplier default)
  2259. // - Download https://github.com/FYSETC/FYSTLCD-2.0
  2260. // - Copy the downloaded SCREEN folder to the SD card.
  2261. //
  2262. // HIPRECY (Supplier default)
  2263. // - Download https://github.com/HiPrecy/Touch-Lcd-LEO
  2264. // - Copy the downloaded DWIN_SET folder to the SD card.
  2265. //
  2266. // MKS (MKS-H43) (Supplier default)
  2267. // - Download https://github.com/makerbase-mks/MKS-H43
  2268. // - Copy the downloaded DWIN_SET folder to the SD card.
  2269. //
  2270. // RELOADED (T5UID1)
  2271. // - Download https://github.com/Desuuuu/DGUS-reloaded/releases
  2272. // - Copy the downloaded DWIN_SET folder to the SD card.
  2273. //
  2274. //#define DGUS_LCD_UI_ORIGIN
  2275. //#define DGUS_LCD_UI_FYSETC
  2276. //#define DGUS_LCD_UI_HIPRECY
  2277. //#define DGUS_LCD_UI_MKS
  2278. //#define DGUS_LCD_UI_RELOADED
  2279. #if ENABLED(DGUS_LCD_UI_MKS)
  2280. #define USE_MKS_GREEN_UI
  2281. #endif
  2282. //
  2283. // Touch-screen LCD for Malyan M200/M300 printers
  2284. //
  2285. //#define MALYAN_LCD
  2286. #if ENABLED(MALYAN_LCD)
  2287. #define LCD_SERIAL_PORT 1 // Default is 1 for Malyan M200
  2288. #endif
  2289. //
  2290. // Touch UI for FTDI EVE (FT800/FT810) displays
  2291. // See Configuration_adv.h for all configuration options.
  2292. //
  2293. //#define TOUCH_UI_FTDI_EVE
  2294. //
  2295. // Touch-screen LCD for Anycubic printers
  2296. //
  2297. //#define ANYCUBIC_LCD_I3MEGA
  2298. //#define ANYCUBIC_LCD_CHIRON
  2299. #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
  2300. #define LCD_SERIAL_PORT 3 // Default is 3 for Anycubic
  2301. //#define ANYCUBIC_LCD_DEBUG
  2302. #endif
  2303. //
  2304. // 320x240 Nextion 2.8" serial TFT Resistive Touch Screen NX3224T028
  2305. //
  2306. //#define NEXTION_TFT
  2307. #if ENABLED(NEXTION_TFT)
  2308. #define LCD_SERIAL_PORT 1 // Default is 1 for Nextion
  2309. #endif
  2310. //
  2311. // Third-party or vendor-customized controller interfaces.
  2312. // Sources should be installed in 'src/lcd/extui'.
  2313. //
  2314. //#define EXTENSIBLE_UI
  2315. #if ENABLED(EXTENSIBLE_UI)
  2316. //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display
  2317. #endif
  2318. //=============================================================================
  2319. //=============================== Graphical TFTs ==============================
  2320. //=============================================================================
  2321. /**
  2322. * Specific TFT Model Presets. Enable one of the following options
  2323. * or enable TFT_GENERIC and set sub-options.
  2324. */
  2325. //
  2326. // 480x320, 3.5", SPI Display with Rotary Encoder from MKS
  2327. // Usually paired with MKS Robin Nano V2 & V3
  2328. //
  2329. //#define MKS_TS35_V2_0
  2330. //
  2331. // 320x240, 2.4", FSMC Display From MKS
  2332. // Usually paired with MKS Robin Nano V1.2
  2333. //
  2334. //#define MKS_ROBIN_TFT24
  2335. //
  2336. // 320x240, 2.8", FSMC Display From MKS
  2337. // Usually paired with MKS Robin Nano V1.2
  2338. //
  2339. //#define MKS_ROBIN_TFT28
  2340. //
  2341. // 320x240, 3.2", FSMC Display From MKS
  2342. // Usually paired with MKS Robin Nano V1.2
  2343. //
  2344. //#define MKS_ROBIN_TFT32
  2345. //
  2346. // 480x320, 3.5", FSMC Display From MKS
  2347. // Usually paired with MKS Robin Nano V1.2
  2348. //
  2349. //#define MKS_ROBIN_TFT35
  2350. //
  2351. // 480x272, 4.3", FSMC Display From MKS
  2352. //
  2353. //#define MKS_ROBIN_TFT43
  2354. //
  2355. // 320x240, 3.2", FSMC Display From MKS
  2356. // Usually paired with MKS Robin
  2357. //
  2358. //#define MKS_ROBIN_TFT_V1_1R
  2359. //
  2360. // 480x320, 3.5", FSMC Stock Display from TronxXY
  2361. //
  2362. //#define TFT_TRONXY_X5SA
  2363. //
  2364. // 480x320, 3.5", FSMC Stock Display from AnyCubic
  2365. //
  2366. //#define ANYCUBIC_TFT35
  2367. //
  2368. // 320x240, 2.8", FSMC Stock Display from Longer/Alfawise
  2369. //
  2370. //#define LONGER_LK_TFT28
  2371. //
  2372. // 320x240, 2.8", FSMC Stock Display from ET4
  2373. //
  2374. //#define ANET_ET4_TFT28
  2375. //
  2376. // 480x320, 3.5", FSMC Stock Display from ET5
  2377. //
  2378. //#define ANET_ET5_TFT35
  2379. //
  2380. // 1024x600, 7", RGB Stock Display with Rotary Encoder from BIQU-BX
  2381. //
  2382. //#define BIQU_BX_TFT70
  2383. //
  2384. // 480x320, 3.5", SPI Stock Display with Rotary Encoder from BIQU B1 SE Series
  2385. //
  2386. //#define BTT_TFT35_SPI_V1_0
  2387. //
  2388. // Generic TFT with detailed options
  2389. //
  2390. //#define TFT_GENERIC
  2391. #if ENABLED(TFT_GENERIC)
  2392. // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
  2393. #define TFT_DRIVER AUTO
  2394. // Interface. Enable one of the following options:
  2395. //#define TFT_INTERFACE_FSMC
  2396. //#define TFT_INTERFACE_SPI
  2397. // TFT Resolution. Enable one of the following options:
  2398. //#define TFT_RES_320x240
  2399. //#define TFT_RES_480x272
  2400. //#define TFT_RES_480x320
  2401. //#define TFT_RES_1024x600
  2402. #endif
  2403. /**
  2404. * TFT UI - User Interface Selection. Enable one of the following options:
  2405. *
  2406. * TFT_CLASSIC_UI - Emulated DOGM - 128x64 Upscaled
  2407. * TFT_COLOR_UI - Marlin Default Menus, Touch Friendly, using full TFT capabilities
  2408. * TFT_LVGL_UI - A Modern UI using LVGL
  2409. *
  2410. * For LVGL_UI also copy the 'assets' folder from the build directory to the
  2411. * root of your SD card, together with the compiled firmware.
  2412. */
  2413. //#define TFT_CLASSIC_UI
  2414. //#define TFT_COLOR_UI
  2415. //#define TFT_LVGL_UI
  2416. #if ENABLED(TFT_LVGL_UI)
  2417. //#define MKS_WIFI_MODULE // MKS WiFi module
  2418. #endif
  2419. /**
  2420. * TFT Rotation. Set to one of the following values:
  2421. *
  2422. * TFT_ROTATE_90, TFT_ROTATE_90_MIRROR_X, TFT_ROTATE_90_MIRROR_Y,
  2423. * TFT_ROTATE_180, TFT_ROTATE_180_MIRROR_X, TFT_ROTATE_180_MIRROR_Y,
  2424. * TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y,
  2425. * TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION
  2426. */
  2427. //#define TFT_ROTATION TFT_NO_ROTATION
  2428. //=============================================================================
  2429. //============================ Other Controllers ============================
  2430. //=============================================================================
  2431. //
  2432. // Ender-3 v2 OEM display. A DWIN display with Rotary Encoder.
  2433. //
  2434. //#define DWIN_CREALITY_LCD // Creality UI
  2435. //#define DWIN_CREALITY_LCD_ENHANCED // Enhanced UI
  2436. //#define DWIN_CREALITY_LCD_JYERSUI // Jyers UI by Jacob Myers
  2437. //#define DWIN_MARLINUI_PORTRAIT // MarlinUI (portrait orientation)
  2438. //#define DWIN_MARLINUI_LANDSCAPE // MarlinUI (landscape orientation)
  2439. //
  2440. // Touch Screen Settings
  2441. //
  2442. //#define TOUCH_SCREEN
  2443. #if ENABLED(TOUCH_SCREEN)
  2444. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  2445. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  2446. //#define TOUCH_IDLE_SLEEP 300 // (secs) Turn off the TFT backlight if set (5mn)
  2447. #define TOUCH_SCREEN_CALIBRATION
  2448. //#define TOUCH_CALIBRATION_X 12316
  2449. //#define TOUCH_CALIBRATION_Y -8981
  2450. //#define TOUCH_OFFSET_X -43
  2451. //#define TOUCH_OFFSET_Y 257
  2452. //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
  2453. #if BOTH(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
  2454. #define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
  2455. #endif
  2456. #if ENABLED(TFT_COLOR_UI)
  2457. //#define SINGLE_TOUCH_NAVIGATION
  2458. #endif
  2459. #endif
  2460. //
  2461. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  2462. // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
  2463. //
  2464. //#define REPRAPWORLD_KEYPAD
  2465. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  2466. //
  2467. // EasyThreeD ET-4000+ with button input and status LED
  2468. //
  2469. //#define EASYTHREED_UI
  2470. //=============================================================================
  2471. //=============================== Extra Features ==============================
  2472. //=============================================================================
  2473. // @section extras
  2474. // Set number of user-controlled fans. Disable to use all board-defined fans.
  2475. // :[1,2,3,4,5,6,7,8]
  2476. //#define NUM_M106_FANS 1
  2477. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  2478. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  2479. // is too low, you should also increment SOFT_PWM_SCALE.
  2480. //#define FAN_SOFT_PWM
  2481. // Incrementing this by 1 will double the software PWM frequency,
  2482. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  2483. // However, control resolution will be halved for each increment;
  2484. // at zero value, there are 128 effective control positions.
  2485. // :[0,1,2,3,4,5,6,7]
  2486. #define SOFT_PWM_SCALE 0
  2487. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  2488. // be used to mitigate the associated resolution loss. If enabled,
  2489. // some of the PWM cycles are stretched so on average the desired
  2490. // duty cycle is attained.
  2491. //#define SOFT_PWM_DITHER
  2492. // Temperature status LEDs that display the hotend and bed temperature.
  2493. // If all hotends, bed temperature, and target temperature are under 54C
  2494. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  2495. //#define TEMP_STAT_LEDS
  2496. // Support for the BariCUDA Paste Extruder
  2497. //#define BARICUDA
  2498. // Support for BlinkM/CyzRgb
  2499. //#define BLINKM
  2500. // Support for PCA9632 PWM LED driver
  2501. //#define PCA9632
  2502. // Support for PCA9533 PWM LED driver
  2503. //#define PCA9533
  2504. /**
  2505. * RGB LED / LED Strip Control
  2506. *
  2507. * Enable support for an RGB LED connected to 5V digital pins, or
  2508. * an RGB Strip connected to MOSFETs controlled by digital pins.
  2509. *
  2510. * Adds the M150 command to set the LED (or LED strip) color.
  2511. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  2512. * luminance values can be set from 0 to 255.
  2513. * For NeoPixel LED an overall brightness parameter is also available.
  2514. *
  2515. * *** CAUTION ***
  2516. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  2517. * as the Arduino cannot handle the current the LEDs will require.
  2518. * Failure to follow this precaution can destroy your Arduino!
  2519. * NOTE: A separate 5V power supply is required! The NeoPixel LED needs
  2520. * more current than the Arduino 5V linear regulator can produce.
  2521. * *** CAUTION ***
  2522. *
  2523. * LED Type. Enable only one of the following two options.
  2524. */
  2525. //#define RGB_LED
  2526. //#define RGBW_LED
  2527. #if EITHER(RGB_LED, RGBW_LED)
  2528. //#define RGB_LED_R_PIN 34
  2529. //#define RGB_LED_G_PIN 43
  2530. //#define RGB_LED_B_PIN 35
  2531. //#define RGB_LED_W_PIN -1
  2532. #endif
  2533. // Support for Adafruit NeoPixel LED driver
  2534. //#define NEOPIXEL_LED
  2535. #if ENABLED(NEOPIXEL_LED)
  2536. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  2537. //#define NEOPIXEL_PIN 4 // LED driving pin
  2538. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  2539. //#define NEOPIXEL2_PIN 5
  2540. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
  2541. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  2542. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  2543. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  2544. // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
  2545. //#define NEOPIXEL2_SEPARATE
  2546. #if ENABLED(NEOPIXEL2_SEPARATE)
  2547. #define NEOPIXEL2_PIXELS 15 // Number of LEDs in the second strip
  2548. #define NEOPIXEL2_BRIGHTNESS 127 // Initial brightness (0-255)
  2549. #define NEOPIXEL2_STARTUP_TEST // Cycle through colors at startup
  2550. #else
  2551. //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel
  2552. #endif
  2553. // Use some of the NeoPixel LEDs for static (background) lighting
  2554. //#define NEOPIXEL_BKGD_INDEX_FIRST 0 // Index of the first background LED
  2555. //#define NEOPIXEL_BKGD_INDEX_LAST 5 // Index of the last background LED
  2556. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  2557. //#define NEOPIXEL_BKGD_ALWAYS_ON // Keep the backlight on when other NeoPixels are off
  2558. #endif
  2559. /**
  2560. * Printer Event LEDs
  2561. *
  2562. * During printing, the LEDs will reflect the printer status:
  2563. *
  2564. * - Gradually change from blue to violet as the heated bed gets to target temp
  2565. * - Gradually change from violet to red as the hotend gets to temperature
  2566. * - Change to white to illuminate work surface
  2567. * - Change to green once print has finished
  2568. * - Turn off after the print has finished and the user has pushed a button
  2569. */
  2570. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  2571. #define PRINTER_EVENT_LEDS
  2572. #endif
  2573. /**
  2574. * Number of servos
  2575. *
  2576. * For some servo-related options NUM_SERVOS will be set automatically.
  2577. * Set this manually if there are extra servos needing manual control.
  2578. * Set to 0 to turn off servo support.
  2579. */
  2580. //#define NUM_SERVOS 3 // Note: Servo index starts with 0 for M280-M282 commands
  2581. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  2582. // 300ms is a good value but you can try less delay.
  2583. // If the servo can't reach the requested position, increase it.
  2584. #define SERVO_DELAY { 300 }
  2585. // Only power servos during movement, otherwise leave off to prevent jitter
  2586. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  2587. // Edit servo angles with M281 and save to EEPROM with M500
  2588. //#define EDITABLE_SERVO_ANGLES
  2589. // Disable servo with M282 to reduce power consumption, noise, and heat when not in use
  2590. //#define SERVO_DETACH_GCODE