auto_brightness.md 8.5KB
title: AutoBrightness description: USB ambient light sensor for DDC/CI backlight control parent: projects git: https://git.xythobuz.de/thomas/AutoBrightness github: https://github.com/xythobuz/AutoBrightness date: 2024-09-07 update: 2024-09-09
comments: true
One of my two ~10 year old 23” 1080p main displays died recently. So I finally upgraded to two used 27” 1440p displays. These are now the first displays on my desktop that allow adjustments of the backlight from software. So I tried to find out how to go about that.
Turns out on laptops both the display backlight intensity and the ambient light sensors are controlled via ACPI, with proper kernel support already available (see eg. the Arch Wiki).
But on desktops no standard for ambient light sensors seems to be established. Instead of ACPI, the backlight of some desktop monitors can be controlled using DDC/CI.
There are some projects, both hardware and software, available for this already. But as usual I decided to make my own.
Prototype Hardware
Initially I tought I could just go the most simple route and use an LDR on the ADC of an MCU. I already had a Digispark Rev. 3 clone, LDR, resistor and potentiometer on hand.
But deep down I already knew this would not be good.
The range of LDRs is far too big to easily measure the human eye dynamic range with an ADC. You can extend the range by switching different resistor values into your voltage divider using GPIOs, but I didn’t want to go that far. Instead I added a 1M potentiometer to manually adjust the measurement range.
This gave me an opportunity to play around with integer low pass filters using bit shifts, as described here (which I got from here).
So as suspected, the resulting values were not able to measure both a dark room at night and a sunny day.
Proper Hardware
To get usable values I had to use a “real” sensor.
The final hardware is just a Digispark Rev. 3 clone with a GY-302 breakout board (for the BH1750 sensor) connected to it.
The BH1750 is a nice small ambient light sensor and very easy to use. This is literally the whole driver I wrote.
void luxInit(void) {
twiWrite(LUX_ADDR, OP_POWER_ON); // reset registers
twiWrite(LUX_ADDR, OP_CONT_0_5X); // continuous measurement at 0.5lx resolution
}
uint16_t luxGet(void) {
uint16_t val = twiRead(LUX_ADDR); // read measurement
return val;
}
USB Communication
The Digispark has the USB D+ and D- signals directly connected to GPIOs of the AtTiny85. So the USB protocol is bit-banged using the V-USB library. Because I did not use the Arduino Cores already available, I had to do some fiddling to configure the library properly for this device.
The code is based on the custom-class example from V-USB. This abuses USB control transfers to transmit data.
On the PC side I’m using PyUSB instead of going to libusb directly, as in the example.
CUSTOM_RQ_GET = 2 # get ldr value
def is_target_device(dev):
if dev.manufacturer == "xythobuz.de" and dev.product == "AutoBrightness":
return True
return False
dev = usb.core.find(idVendor=0x16c0, idProduct=0x05dc, custom_match=is_target_device)
dev.set_configuration()
r = dev.ctrl_transfer(usb.util.CTRL_TYPE_VENDOR | usb.util.CTRL_IN, CUSTOM_RQ_GET, 0, 0, 2)
val = int.from_bytes(r, "little")
To run this without root permissions you need to add a udev rule (in eg. /etc/udev/rules.d/49-autobrightness.rules).
SUBSYSTEMS=="usb", ATTRS{idVendor}=="16c0", ATTRS{idProduct}=="05dc", ATTRS{manufacturer}=="xythobuz.de", ATTRS{product}=="AutoBrightness", MODE:="0666"
I’m using the shared V-USB vendor and product IDs, so I have to always do the matching using my manufacturer and product strings as well.
Prototype Client
With the hardware side out of the way the next step was adjusting the display brightness. I made a short prototype using ddcutil to set the values.
To calculate the resulting values I made some measurements at midday (~500 lux) and night (~50 lux). And I thought about my habits (the MSI display seems ~10% brighter than the HP).
c_in = 0.6, -60.0, # in_a, in_b
calibration = {
"HPN:HP 27xq:CNK1072BJY": [
1.0, 30.0, # out_a, out_b
],
"MSI:MSI G27CQ4:": [
1.0, 20.0, # out_a, out_b
],
}
def cal(v, c):
# out = out_b + out_a * in_a * max(0, in_b + in)
return c[1] + c[0] * c_in[0] * max(0, c_in[1] + v)
This simple formula gives surprisingly good results. To avoid noticable noisy changes I do some simple low-pass filtering of the sensor values.
filter_fact = 0.9
def filter_lux(old, new):
return (old * filter_fact) + (new * (1.0 - filter_fact))
All this just runs once per second.
Unfortunately, using ddcutil to adjust the brightness causes a noticable stutter of the whole system each time the value is changed. So this is not a good long-term solution.
Telling ddcutil to directly talk to the I2C bus helped a bit, but it still stutters slightly.
To alleviate this a bit I’m now using a KWin script to check for a full-screen app so I can pause brightness updates.
As usual I’m also sending all these values to my local InfluxDB.
Proper Client
My initial idea for the client was to use the ambient light sensor to also “calibrate” the two displays to each other.
To do this, a white square could be shown on both screens.
Then the sensor can be placed in front of each display to measure their brightness “ramps”.
This could then give the calibration dictionary shown above.
To determine the c_in values the room brightness has to be measured at day and night.
This should automate the process I’ve done manually to determine the calibration values.
But as you may have noticed, I’m more the prototype kind of guy and don’t really do finished products on here. So…
To Do 😅
License
The AutoBrightness project is licensed under the GNU General Public License.
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
See <http://www.gnu.org/licenses/>.