Why double touch probing is not a good thing.

It's widely believed we can get better __probing__ results when using a double touch when probing.

Let's compare to double touch __homing__.
Or better let's begin with single touch __homing__.
We home to find out out position, so our position is unknown.
To find the endstop we have to move into the direction of the endstop.
The maximum way we have to move is a bit longer than the axis length.
When we arrive at the endstop - when it triggers, the stepper pulses are stopped immediately.
It's a sudden stop. No smooth deacceleration is possible.
Depending on the speed and the moving mass we lose steps here.
Only if we approached slow enough (below jerk speed?) we will not lose steps.

Moving a complete axis length, that slow, takes for ever.
To speed up homing, we now make the first approach faster, get a guess about our position,
back up a bit and make a second slower approach to get a exact result without losing steps.

What we do in double touch probing is the same. But the difference here is:
a. we already know where we are
b. if the first approach is to fast we will lose steps here to.
But this time there is no second approach to set the position to 0. We are measuring only.
The lost steps are permanent until we home the next time.

So if you experienced permanently rising values in M48 you now know why. (Too fast, suddenly stopped, first approach)

What can we do to improve probing?
We can use the information about our current position.
We can make a really fast, but deaccelerated, move to a place we know it is a bit before the trigger point.
And then move the rest of the way really slow.

No need for `MANUAL_HOME_POSITIONS`. Just set each one as-needed to
override the automatic behavior.

Rather than include twice, which is tricky but may confuse

Unify run_z_probe
Add double touch for DELTAs.
Introduce Z_PROBE_SPEED_FAST and Z_PROBE_SPEED_SLOW
  defaulting to homing_feedrate_mm_m[Z_AXIS] and homing_feedrate_mm_m[Z_AXIS]/2

・Update forgotten K8400 files

・Update a forgotten Configuration_adv.h of K8400

・Update forgotten Configuration.h of K8400

・Update forgotten example configuration files

Similar to the current Arduino HardwareSerial
but with max. 256 byte buffer-size.

Deactivated by default.

The boards with AT90USB processor (USBCON) already use a TX-buffer.

Add an emergency-command parser to MarlinSerial's RX interrupt.

The parser tries to find and execute M108,M112,M410 before the commands disappear in the RX-buffer.

To avoid false positives for M117, comments and commands followed by filenames (M23, M28, M30, M32, M33) are filtered.

This enables Marlin to receive and react on the Emergency command at all times - regardless of whether the buffers are full or not. It remains to convince hosts to send the commands. To inform the hosts about the new feature a new entry in the M115-report was made. "`EMERGENCY_CODES:M112,M108,M410;`".

The parser is fast. It only ever needs two switch decisions and one assignment of the new state for every character.

One problem remains. If the host has sent an incomplete line before sending an emergency command the emergency command could be omitted when the parser is in `state_IGNORE`.
In that case the host should send "\ncommand\n"

Also introduces M108 to break the waiting for the heaters in M109, M190 and M303.

Rename `cancel_heatup` to `wait_for_heatup` to better see the purpose.

There was an hidden extra move after the scripts. This is configurable now.
Added the extra moves to the relevant configs.

Supports both dual and single head printers (with the correct config).
Includes community sourced feed rate fix.

Rename / move files.

Remove redundant definitions.

・Update a forgotten Configuration_adv.h of Cartesio

Includes:
  *firmware version / branch / date.
  *extruder count
  *board information (name, serial details, power supply type)
  *thermistors (names, min/max temperatures)
  *printer statistics (PRINTCOUNTER details)

Thanks to @thinkyhead for contributions.