Changes to temperature.cpp from Ultimaker fork, intended to address
#1226 and #1227

Done

This define is not used.

Changes to temperature.cpp from Ultimaker fork, intended to address
#1226 and #1227

Without this fix, the code wont compile with extruder but without bed
runaway protection defined.

removed function step_wait() from stepper.cpp because its used nowhere.

Issue #1385 describes a delay that the compiler is optimizing out and
this solution.

# Add: Example Configuration for Vellemann K8200 - based on new
BOARD_K8200 #1391

* K8200: new folder in example_configurations for Vellemann K8200 (3Drag
clone - should work with 3Drag http://reprap.org/wiki/3drag, too. Please
report)
* K8200/Configuration.h/Configuration_adv.h: updated manually with
parameters form genuine Vellemann Firmware "firmware_k8200_marlinv2"
based on the recent development branch

I tested the changes on my K8200 with 20x4-LCD and Arduino 1.0.5 for
Windows (SD library added to IDE manually) - everything works well

## Add: Board for Vellemann K8200 (derived from 3Drag)

* Boards.h: updated comment for board 3Drag - K8200 removed
* Boards.h: added `BOARD_K8200` with ID 78

* language.h.: machine name and firmware URL for new board

* pins.h: added `K8200` to any `#if` with `3Drag` and corresponding
comments

Show Custom M Code when entering M503

This reverts commit 935ee968a7.

Still not fine tuned but working.

When a melzi board and a full gfx are both selected, the build fails
blaming for some missing defines.

This is a fix for the issue: now my configuration works.

## Update Boards.h for Vellemann K8200 - comment only

* Boards.h: updated comment for board 3Drag - K8200 uses same board

This reverts commit 5333590ac2.

* K8200: new folder in example_configurations for Vellemann K8200 (3Drag
clone - should work with 3Drag too, please report)

* K8200/language.h: updated machine name and URL for K8200

* K8200/Configuration.h/Configuration_adv.h: updated manually with
parameters
form genuine Vellemann Firmware "firmware_k8200_marlinv2" based on the
recent development branch

* K8200/files by Vellemann: added folder with original files from
Vellemann homepage, since there is no GitHub fork you could link to by
them

I tested the changes on my K8200 with 20x4-LCD and Arduino 1.0.5 for
Windows - everything works well

Change default value of AVRDUDE_PROGRAMMER to 'wiring'.

Backported from Printrbot branch, allows the fan to work correctly.

G29 E was not retracting the probe on the last probe point when used with ABL grid. Corrected.

* Adds config parameter `PID_PARAMS_PER_EXTRUDER` - allows single PID
parameters to be used where this would be preferable (e.g. dual
identical extruders)
* When disabled, will use `float Kp, Ki, Kd, Kc;` as before.
Preprocessor macros used to switch between.
* ultralcd.cpp defines extra menus for extra parameters only where
required
* M301 reports `e:xx` only if independent pid parameters enabled
* EEPROM structure still leaves space for 3 extruders worth, when undef
will save single parameter to all extruder positions, but only read the
first
* Switching off saves approx 330 B with no LCD enabled, 2634B with LCD
(RRD) enabled: this is significant.
* LCD modifications should be tested.

This change introduces an improvement to G29 command on Marlin.

Auto bed leveling operation's reliability is based on the repeatability of the Z-probe switch and the servo. This change introduces an option to G29 command. When the G29 command is sent with an "e" option, during auto bed levelling the servo is not retracted between probes which decreases the bias on auto bed levelling resulting from servo.

G29 command does the auto bed probing as it is.

G29 E command engages the servo on first probing point, probes all points and retracts the servo after probing the last point.

Please comment your opinions, test on your printer and check the code on a programmer's perspective. (I am not a good programmer.)

* Depending on extruder count, will add menu items for ultralcd to edit
individual PID parameters for each extruder
* Added menu items to each language_xx.h
* Builds OK, but recommend testing with typical LCD

* R-H reads incorrect M301 line from EEPROM output if more than one is
present. Reverted to original output format, using only E0 value.

* Variables Kp, Ki, Kd, Kc now arrays of size EXTRUDERS
* M301 gains (optional, default=0) E parameter to define which
extruder's settings to modify. Tested, works with Repetier Host's EEPROM
config window, albeit only reads/updates settings for E0.
* All Kp, Ki, Kd, Kc parameters saved in EEPROM (version now v14), up to
3 extruders supported (same as Marlin in general)

Small changes (and formatting to confuse the diff’er) which first
allows DOGLCD and LCD_PROGRESS_BAR to be enabled in tandem, then a
#warning (rather than error) that the extra progress bar / message
options don’t apply to graphical displays at this time. This leaves
open perhaps combining the progress bar and message area in some future
(or forked custom) graphical LCD display arrangement (at which time the
relevant variables may be moved into ultralcd.cpp with externs in
ultralcd.h). I also added a conditional error that the progress bar and
the filament display may not work well together.

new version is pretty generic and should work in most scenarios

logo is now 110 pixels wide and starts 9 pixels in from top left corner and also 9 pixels down from same corner... this will give a 9 pixel border all way round

ver info is placed centered and there is a 9 pixel from bottom of display to ver info

The previous calc was wrong. Between N points there are only N-1 gaps,
not N.

So changing AUTO_BED_LEVELING_GRID_POINTS to
(AUTO_BED_LEVELING_GRID_POINTS-1)