marlin

Commit graph

Autor	SHA1	Nachricht	Datum
AnHardt	b7e9ba7591	Back to 1.0.3 dev - for now	vor 9 Jahren
AnHardt	b1404a0743	fix thermal protection state machine target temp. V2 If the target temperature is changed then it would always stay in the reset state. Thanks to @tonokip. Replaces #2119	vor 9 Jahren
AnHardt	17b0ec84ed	Fix out_of_range_error() For sprintf_P() the first parameter has to be a `char` not `const char`.	vor 9 Jahren
wurstnase	e7e964432b	consistency name for multiplier replace extruder_multiply with extruder_multiplier like feedrate_multiplier or volumetric_multiplier	vor 9 Jahren
AnHardt	0d9d21d15f	Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.	vor 9 Jahren
MagoKimbra	881146bc22	Fix problem Width Cura	vor 9 Jahren
Alexey Shvetsov	a8670b66a7	Update ru translation Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>	vor 9 Jahren
fmalpartida	93da52d011	Added support for OLED SSD1306 I2C based LCDs.	vor 9 Jahren
wurstnase	0f3f7d6835	clean up double endstops	vor 9 Jahren
Scott Lahteine	be5236e839	Reduce setTargetedHotend by removing the switch	vor 9 Jahren
Scott Lahteine	06f401e7e5	Redo "invalid extruder" to save 264 bytes - Use `setTargetedHotend` in `M200`, as with other commands that use `T` for the extruder - Synthesize the "invalid extruder" message, obviating several long strings	vor 9 Jahren
Scott Lahteine	9beed830eb	Drop commented code_is_good lines	vor 9 Jahren
Scott Lahteine	068d4a1eb2	Ignore unknown commands if they start with G, M, or T	vor 9 Jahren
Scott Lahteine	0564625757	Update M33 for new gcode parser	vor 9 Jahren
AnHardt	f18f689c01	Replace MSG_F? with MSG_N? To avoid double definitions. I prefer to read N for Number not for Nozzle.	vor 9 Jahren
AnHardt	af7e3f5076	Print active extruder with M105 for MAX6675 Was omitted when T0 is a MAX6675.	vor 9 Jahren
Jonathan Bastien-Filiatrault	d46d9d998e	Add maximum bed integral term in example configurations.	vor 9 Jahren
Jonathan Bastien-Filiatrault	e86f2342c0	Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX. My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed to reach its intended temperature. The head requires a low maximum power since I run on 24 volts and it has a somewhat low thermal mass.	vor 9 Jahren
AnHardt	f0523b5816	Initialize the display earlier to have it ready to display errors during (temperature)-setup.	vor 9 Jahren
Scott Lahteine	790c697c19	Fix DEGREES macro	vor 9 Jahren
Scott Lahteine	03d5709b09	M110 is a known command - The command parser now displays “unknown command” in more cases. Known commands must be added to the `switch` inside `process_commands` to suppress the error.	vor 9 Jahren
Scott Lahteine	d76a01194d	Slight size reduction by adding idle()	vor 9 Jahren
Richard Wackerbarth	2deb5a8ac5	Temporary Hack REVERT THIS CHANGE In proper use, we want to force the vendor to update this file to reflect distribution parameters However, until most users have converted to automatic versioning, we “grant them a pass”	vor 9 Jahren
Richard Wackerbarth	b5743d6927	Use SOURCE_CODE_URL rather than FIRMWARE_URL	vor 9 Jahren
Richard Wackerbarth	5ea139fd79	Revised Versioning mechanism	vor 9 Jahren
AnHardt	da246f5cb1	Activate BED_MINTEMP error. And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error(). Includes #2156.	vor 9 Jahren
AnHardt	959da98d8e	Call kill() only once when triggered by a temperature error to avoid stack overflow when called from interrupt. Some clean up for calls of disable_all_heaters(). 'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().	vor 9 Jahren
Scott Lahteine	68f6f149d0	Reduce code size with out_of_range_error function - Affects code size when automatic bed leveling is enabled	vor 9 Jahren
wurstnase	94120740d8	faster compare !(~(ab)&0x3) and ab == 0x3 are equal	vor 9 Jahren
Scott Lahteine	b55f8718c3	Indent G90/G91, G92	vor 9 Jahren
Scott Lahteine	b0d520b109	Indent G30, G31/G32	vor 9 Jahren
Scott Lahteine	ffe27a6225	Indent G29	vor 9 Jahren
Scott Lahteine	86083badc2	Indent G4, G10/G11, G28	vor 9 Jahren
Scott Lahteine	47d7a9cb5e	Indent G2/G3	vor 9 Jahren
Scott Lahteine	350f239d84	Indent G0/G1	vor 9 Jahren
Scott Lahteine	672b0c1fd3	Cleanup pins in RAMPS_13_EFB boards	vor 9 Jahren
Scott Lahteine	15a2351675	No need for +1 on initial seen_pointer	vor 9 Jahren
Scott Lahteine	550dd87b2a	Set seen_pointer before calling code_value	vor 9 Jahren
Scott Lahteine	063881b5bd	Fix a couple of doubled semicolons	vor 9 Jahren
AnHardt	0c0ace2a04	Remove start_watching_heater() fom M104 and M109	vor 9 Jahren
Scott Lahteine	00716d0ca0	Small start_watching_heater adjustment	vor 9 Jahren
Scott Lahteine	bde9c70d42	Suppress the line mismatch error after M303	vor 9 Jahren
wurstnase	ff98b8632b	new endstop bits	vor 9 Jahren
AnHardt	9b0fa9c309	Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS	vor 9 Jahren
AnHardt	bc0764894a	Shift call of start_watching_heater() into setTargetHotend() to warrant watching is set or reset. Make setTargetBed() in _lcd_preheat() dependant of TEMP_SENSOR_BED. Use disable_all_heaters() in lcd_cooldown() and abort_on_endstop_hit.	vor 9 Jahren
Richard Wackerbarth	b878bc5620	Introducing the Kossel Pro Build Configuration	vor 9 Jahren
Richard Wackerbarth	1d8f61ca8a	AT90USB is defined in pins.h	vor 9 Jahren
Richard Wackerbarth	735bf2d35f	Describe Custom M Code	vor 9 Jahren
Scott Lahteine	f39658c822	M120 and M121 are reversed	vor 9 Jahren
Scott Lahteine	6eb4f90ce7	Also synchronize configurator copies of configs	vor 9 Jahren

Erste Vorherige 1 2 3 4 5 ... Nächste Letzte

2726 Commits (5ed0c1a2bd272c374ecf77559261c820ef0a50b3)