Scott Lahteine
99282a46e9
Make sure ABL (manual) starts close to the bed
6 anos atrás
Roxy-3D
21f13f9e57
Stow Probe at end of G29 J3
6 anos atrás
KangDroid
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops (#10389 )
6 anos atrás
Scott Lahteine
3c5c6d478a
Prettify process_parsed_command
6 anos atrás
Scott Lahteine
0535ebc4d2
MESH_BED_LEVELING before PROBE_MANUALLY
6 anos atrás
Scott Lahteine
bb7064cc30
Tweak MBL move to bed code
6 anos atrás
Chris Pepper
cc6d41e1d3
Use a macro for HAL header redirection (#10380 )
6 anos atrás
Luc Van Daele
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT (#10386 )
6 anos atrás
Yunhui Fu
c96412a78f
[2.0.x] UTF-8 language translation support (#10213 )
6 anos atrás
Scott Lahteine
daa712455b
Make sure MBL starts close to the bed
Fix #10390
6 anos atrás
Scott Lahteine
4c8751727a
Fix M118 parameter handling
Fix #10388
6 anos atrás
Scott Lahteine
3bc179a16f
Compress/update comments ubl_motion
…to fit more code on the screen and correct outdated commentary contrasting ABL.
6 anos atrás
Luc Van Daele
646aa20b43
Overhaul of G33 Delta Calibration (#8822 )
6 anos atrás
Luc Van Daele
ac2e0afb62
Low Point for delta calibration (#10363 )
6 anos atrás
Eduardo José Tagle
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR (#10373 )
6 anos atrás
Bob-the-Kuhn
85014cd132
[2.0.x] LPC1768 - automatic selection of upload disk (#10374 )
6 anos atrás
Scott Lahteine
472ab0cc24
Tweak RAMPS SDSS pins
6 anos atrás
LichtiMC
b94c8defee
Provide additional information about SMART-RAMPS board (#10353 )
6 anos atrás
Scott Lahteine
6f8e228880
Add RESET_PIN to pins_RAMPS_SMART.h
6 anos atrás
Sean
2d9b0a66fe
Add Filament Change accelerations
6 anos atrás
Scott Lahteine
71d3523254
Add Filament Change accelerations to example configs
6 anos atrás
Scott Lahteine
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
6 anos atrás
Scott Lahteine
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
6 anos atrás
Roxy-3D
a731a723e8
Better i3-2020 Z_PROBE_OFFSET_FROM_EXTRUDER
6 anos atrás
Roxy-3D
26cc12eaa4
Resolve corruption of Max7219 Debug LED Matrix
6 anos atrás
Scott Lahteine
dca69efc11
Update Bed PID comments
6 anos atrás
Scott Lahteine
56486c5c0e
Apply const to manage_inactivity
6 anos atrás
Scott Lahteine
a6485456df
Fix LIGHTWEIGHT_UI with UBL
See https://github.com/MarlinFirmware/Marlin/issues/10317#issuecomment -379100702
6 anos atrás
Scott Lahteine
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
As suggested by @GMagician
6 anos atrás
Scott Lahteine
44a697ab04
Set STM32F1 TEMP_TIMER_FREQUENCY to 1K
Responding to https://github.com/MarlinFirmware/Marlin/pull/8833#issuecomment -379426803
6 anos atrás
Scott Lahteine
cec6e19099
Add RepRapPro Huxley configuration
Based on #10343 by @indazoo
6 anos atrás
Scott Lahteine
9ff4e9e1e6
Patch _IS_HW_SPI so defined() works
6 anos atrás
Scott Lahteine
cea398849e
Tweak to gcode_line_error/return
6 anos atrás
etagle
a29adde5c0
Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
6 anos atrás
Scott Lahteine
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
6 anos atrás
Lenbok
0e8242180d
Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
6 anos atrás
Scott Lahteine
5b3bda1c16
Add Chamber Temp options to example configs
6 anos atrás
Bob-the-Kuhn
acda4ecb20
Fix DUE Trinamic SW/HW SPI sanity check (#10336 )
6 anos atrás
Bob-the-Kuhn
ab715c70d1
TMC SPI sanity-check and pins debugging (#10324 )
6 anos atrás
Scott Lahteine
4dc7e64789
Update Slovak language
Based on #10313 by @rmoravcik
6 anos atrás
Marcio Teixeira
2efc072fdb
Clear progress bar on completion (#10333 )
Fix #10330
6 anos atrás
GMagician
6ce060cfe0
[2.0.x] Update language_it.h (#10322 )
Updated to #10296
6 anos atrás
Marcio Teixeira
9356cf648f
Added support for Einsy Retro
http://reprap.org/wiki/EinsyRetro
6 anos atrás
Marcio Teixeira
75037493fa
Default active low for TMC2130 DIAG1 (#10294 )
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
6 anos atrás
Scott Lahteine
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
6 anos atrás
Scott Lahteine
051303ad42
Russian language updates
From #10311 by @anton-piliugin
6 anos atrás
Sean
2fa0a73c2c
Implement filament change continuous purge
6 anos atrás
Scott Lahteine
d133ad61f3
Add continuous purge to example configs
6 anos atrás
Scott Lahteine
4b25543633
Backtrace formatting cleanup
6 anos atrás
Bob-the-Kuhn
902c885782
Switch to TMC2130 compatible hardware SPI & misc (#10299 )
6 anos atrás