marlin/Marlin/src/HAL/DUE/usb/sysclk.h

/**
 * \file
 *
 * \brief Chip-specific system clock management functions.
 *
 * Copyright (c) 2011-2015 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
 */

#ifndef CHIP_SYSCLK_H_INCLUDED
#define CHIP_SYSCLK_H_INCLUDED

#include "osc.h"
#include "pll.h"

/**
 * \page sysclk_quickstart Quick Start Guide for the System Clock Management service (SAM3A)
 *
 * This is the quick start guide for the \ref sysclk_group "System Clock Management"
 * service, with step-by-step instructions on how to configure and use the service for
 * specific use cases.
 *
 * \section sysclk_quickstart_usecases System Clock Management use cases
 * - \ref sysclk_quickstart_basic
 *
 * \section sysclk_quickstart_basic Basic usage of the System Clock Management service
 * This section will present a basic use case for the System Clock Management service.
 * This use case will configure the main system clock to 84MHz, using an internal PLL
 * module to multiply the frequency of a crystal attached to the microcontroller.
 *
 * \subsection sysclk_quickstart_use_case_1_prereq Prerequisites
 *  - None
 *
 * \subsection sysclk_quickstart_use_case_1_setup_steps Initialization code
 * Add to the application initialization code:
 * \code
	sysclk_init();
\endcode
 *
 * \subsection sysclk_quickstart_use_case_1_setup_steps_workflow Workflow
 * -# Configure the system clocks according to the settings in conf_clock.h:
 *    \code sysclk_init(); \endcode
 *
 * \subsection sysclk_quickstart_use_case_1_example_code Example code
 *   Add or uncomment the following in your conf_clock.h header file, commenting out all other
 *   definitions of the same symbol(s):
 *   \code
	   #define CONFIG_SYSCLK_SOURCE        SYSCLK_SRC_PLLACK

	   // Fpll0 = (Fclk * PLL_mul) / PLL_div
	   #define CONFIG_PLL0_SOURCE          PLL_SRC_MAINCK_XTAL
	   #define CONFIG_PLL0_MUL             (84000000UL / BOARD_FREQ_MAINCK_XTAL)
	   #define CONFIG_PLL0_DIV             1

	   // Fbus = Fsys / BUS_div
	   #define CONFIG_SYSCLK_PRES          SYSCLK_PRES_1
\endcode
 *
 * \subsection sysclk_quickstart_use_case_1_example_workflow Workflow
 *  -# Configure the main system clock to use the output of the PLL module as its source:
 *   \code #define CONFIG_SYSCLK_SOURCE          SYSCLK_SRC_PLLACK \endcode
 *  -# Configure the PLL module to use the fast external fast crystal oscillator as its source:
 *   \code #define CONFIG_PLL0_SOURCE            PLL_SRC_MAINCK_XTAL \endcode
 *  -# Configure the PLL module to multiply the external fast crystal oscillator frequency up to 84MHz:
 *   \code
	#define CONFIG_PLL0_MUL             (84000000UL / BOARD_FREQ_MAINCK_XTAL)
	#define CONFIG_PLL0_DIV             1
\endcode
 *   \note For user boards, \c BOARD_FREQ_MAINCK_XTAL should be defined in the board \c conf_board.h configuration
 *         file as the frequency of the fast crystal attached to the microcontroller.
 *  -# Configure the main clock to run at the full 84MHz, disable scaling of the main system clock speed:
 *    \code
	#define CONFIG_SYSCLK_PRES         SYSCLK_PRES_1
\endcode
 *    \note Some dividers are powers of two, while others are integer division factors. Refer to the
 *          formulas in the conf_clock.h template commented above each division define.
 */

/// @cond 0
/**INDENT-OFF**/
#ifdef __cplusplus
extern "C" {
#endif
/**INDENT-ON**/
/// @endcond

/**
 * \weakgroup sysclk_group
 * @{
 */

//! \name Configuration Symbols
//@{
/**
 * \def CONFIG_SYSCLK_SOURCE
 * \brief Initial/static main system clock source
 *
 * The main system clock will be configured to use this clock during
 * initialization.
 */
#ifndef CONFIG_SYSCLK_SOURCE
# define CONFIG_SYSCLK_SOURCE   SYSCLK_SRC_MAINCK_4M_RC
#endif
/**
 * \def CONFIG_SYSCLK_PRES
 * \brief Initial CPU clock divider (mck)
 *
 * The MCK will run at
 * \f[
 *   f_{MCK} = \frac{f_{sys}}{\mathrm{CONFIG\_SYSCLK\_PRES}}\,\mbox{Hz}
 * \f]
 * after initialization.
 */
#ifndef CONFIG_SYSCLK_PRES
# define CONFIG_SYSCLK_PRES  0
#endif

//@}

//! \name Master Clock Sources (MCK)
//@{
#define SYSCLK_SRC_SLCK_RC              0       //!< Internal 32kHz RC oscillator as master source clock
#define SYSCLK_SRC_SLCK_XTAL            1       //!< External 32kHz crystal oscillator as master source clock
#define SYSCLK_SRC_SLCK_BYPASS          2       //!< External 32kHz bypass oscillator as master source clock
#define SYSCLK_SRC_MAINCK_4M_RC         3       //!< Internal 4MHz RC oscillator as master source clock
#define SYSCLK_SRC_MAINCK_8M_RC         4       //!< Internal 8MHz RC oscillator as master source clock
#define SYSCLK_SRC_MAINCK_12M_RC        5       //!< Internal 12MHz RC oscillator as master source clock
#define SYSCLK_SRC_MAINCK_XTAL          6       //!< External crystal oscillator as master source clock
#define SYSCLK_SRC_MAINCK_BYPASS        7       //!< External bypass oscillator as master source clock
#define SYSCLK_SRC_PLLACK               8       //!< Use PLLACK as master source clock
#define SYSCLK_SRC_UPLLCK               9       //!< Use UPLLCK as master source clock
//@}

//! \name Master Clock Prescalers (MCK)
//@{
#define SYSCLK_PRES_1           PMC_MCKR_PRES_CLK_1     //!< Set master clock prescaler to 1
#define SYSCLK_PRES_2           PMC_MCKR_PRES_CLK_2     //!< Set master clock prescaler to 2
#define SYSCLK_PRES_4           PMC_MCKR_PRES_CLK_4     //!< Set master clock prescaler to 4
#define SYSCLK_PRES_8           PMC_MCKR_PRES_CLK_8     //!< Set master clock prescaler to 8
#define SYSCLK_PRES_16          PMC_MCKR_PRES_CLK_16    //!< Set master clock prescaler to 16
#define SYSCLK_PRES_32          PMC_MCKR_PRES_CLK_32    //!< Set master clock prescaler to 32
#define SYSCLK_PRES_64          PMC_MCKR_PRES_CLK_64    //!< Set master clock prescaler to 64
#define SYSCLK_PRES_3           PMC_MCKR_PRES_CLK_3     //!< Set master clock prescaler to 3
//@}

//! \name USB Clock Sources
//@{
#define USBCLK_SRC_PLL0       0     //!< Use PLLA
#define USBCLK_SRC_UPLL       1     //!< Use UPLL
//@}

/**
 * \def CONFIG_USBCLK_SOURCE
 * \brief Configuration symbol for the USB generic clock source
 *
 * Sets the clock source to use for the USB. The source must also be properly
 * configured.
 *
 * Define this to one of the \c USBCLK_SRC_xxx settings. Leave it undefined if
 * USB is not required.
 */
#ifdef __DOXYGEN__
# define CONFIG_USBCLK_SOURCE
#endif

/**
 * \def CONFIG_USBCLK_DIV
 * \brief Configuration symbol for the USB generic clock divider setting
 *
 * Sets the clock division for the USB generic clock. If a USB clock source is
 * selected with CONFIG_USBCLK_SOURCE, this configuration symbol must also be
 * defined.
 */
#ifdef __DOXYGEN__
# define CONFIG_USBCLK_DIV
#endif


extern void sysclk_enable_usb(void);
extern void sysclk_disable_usb(void);

//! @}

/// @cond 0
/**INDENT-OFF**/
#ifdef __cplusplus
}
#endif
/**INDENT-ON**/
/// @endcond

#endif /* CHIP_SYSCLK_H_INCLUDED */