🔥 Drop STM L64** drivers, STEVAL_3DP001V1 (#24427)

.github/workflows/test-builds.yml

@@ -81,7 +81,6 @@ jobs:
         - STM32F401RC_creality
         - STM32F103VE_longer
         - STM32F407VE_black
-        - STM32F401VE_STEVAL
         - BIGTREE_BTT002
         - BIGTREE_SKR_PRO
         - BIGTREE_GTR_V1_0

Marlin/Configuration.h

@@ -148,13 +148,12 @@
  *
  * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  *
- * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
- *          TB6560, TB6600, TMC2100,
+ * Options: A4988, A5984, DRV8825, LV8729, TB6560, TB6600, TMC2100,
  *          TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  *          TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
- * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
+ * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
 #define X_DRIVER_TYPE  A4988
 #define Y_DRIVER_TYPE  A4988

Marlin/Configuration_adv.h

@@ -3239,253 +3239,6 @@
 
 #endif // HAS_TRINAMIC_CONFIG
 
-// @section L64XX
-
-/**
- * L64XX Stepper Driver options
- *
- * Arduino-L6470 library (0.8.0 or higher) is required.
- * https://github.com/ameyer/Arduino-L6470
- *
- * Requires the following to be defined in your pins_YOUR_BOARD file
- *     L6470_CHAIN_SCK_PIN
- *     L6470_CHAIN_MISO_PIN
- *     L6470_CHAIN_MOSI_PIN
- *     L6470_CHAIN_SS_PIN
- *     ENABLE_RESET_L64XX_CHIPS(Q)  where Q is 1 to enable and 0 to reset
- */
-
-#if HAS_L64XX
-
-  //#define L6470_CHITCHAT        // Display additional status info
-
-  #if AXIS_IS_L64XX(X)
-    #define X_MICROSTEPS       128  // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) - L6474 max is 16
-    #define X_OVERCURRENT     2000  // (mA) Current where the driver detects an over current
-                                    //   L6470 & L6474 - VALID: 375 x (1 - 16) - 6A max - rounds down
-                                    //   POWERSTEP01: VALID: 1000 x (1 - 32) - 32A max - rounds down
-    #define X_STALLCURRENT    1500  // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) -  4A max - rounds down)
-                                    //   L6470 & L6474 - VALID: 31.25 * (1-128) -  4A max - rounds down
-                                    //   POWERSTEP01: VALID: 200 x (1 - 32) - 6.4A max - rounds down
-                                    //   L6474 - STALLCURRENT setting is used to set the nominal (TVAL) current
-    #define X_MAX_VOLTAGE      127  // 0-255, Maximum effective voltage seen by stepper - not used by L6474
-    #define X_CHAIN_POS         -1  // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI
-    #define X_SLEW_RATE          1  // 0-3, Slew 0 is slowest, 3 is fastest
-  #endif
-
-  #if AXIS_IS_L64XX(X2)
-    #define X2_MICROSTEPS     X_MICROSTEPS
-    #define X2_OVERCURRENT            2000
-    #define X2_STALLCURRENT           1500
-    #define X2_MAX_VOLTAGE             127
-    #define X2_CHAIN_POS                -1
-    #define X2_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(Y)
-    #define Y_MICROSTEPS               128
-    #define Y_OVERCURRENT             2000
-    #define Y_STALLCURRENT            1500
-    #define Y_MAX_VOLTAGE              127
-    #define Y_CHAIN_POS                 -1
-    #define Y_SLEW_RATE                  1
-  #endif
-
-  #if AXIS_IS_L64XX(Y2)
-    #define Y2_MICROSTEPS     Y_MICROSTEPS
-    #define Y2_OVERCURRENT            2000
-    #define Y2_STALLCURRENT           1500
-    #define Y2_MAX_VOLTAGE             127
-    #define Y2_CHAIN_POS                -1
-    #define Y2_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(Z)
-    #define Z_MICROSTEPS               128
-    #define Z_OVERCURRENT             2000
-    #define Z_STALLCURRENT            1500
-    #define Z_MAX_VOLTAGE              127
-    #define Z_CHAIN_POS                 -1
-    #define Z_SLEW_RATE                  1
-  #endif
-
-  #if AXIS_IS_L64XX(Z2)
-    #define Z2_MICROSTEPS     Z_MICROSTEPS
-    #define Z2_OVERCURRENT            2000
-    #define Z2_STALLCURRENT           1500
-    #define Z2_MAX_VOLTAGE             127
-    #define Z2_CHAIN_POS                -1
-    #define Z2_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(Z3)
-    #define Z3_MICROSTEPS     Z_MICROSTEPS
-    #define Z3_OVERCURRENT            2000
-    #define Z3_STALLCURRENT           1500
-    #define Z3_MAX_VOLTAGE             127
-    #define Z3_CHAIN_POS                -1
-    #define Z3_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(Z4)
-    #define Z4_MICROSTEPS     Z_MICROSTEPS
-    #define Z4_OVERCURRENT            2000
-    #define Z4_STALLCURRENT           1500
-    #define Z4_MAX_VOLTAGE             127
-    #define Z4_CHAIN_POS                -1
-    #define Z4_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(I)
-    #define I_MICROSTEPS      128
-    #define I_OVERCURRENT    2000
-    #define I_STALLCURRENT   1500
-    #define I_MAX_VOLTAGE     127
-    #define I_CHAIN_POS        -1
-    #define I_SLEW_RATE         1
-  #endif
-
-  #if AXIS_IS_L64XX(J)
-    #define J_MICROSTEPS      128
-    #define J_OVERCURRENT    2000
-    #define J_STALLCURRENT   1500
-    #define J_MAX_VOLTAGE     127
-    #define J_CHAIN_POS        -1
-    #define J_SLEW_RATE         1
-  #endif
-
-  #if AXIS_IS_L64XX(K)
-    #define K_MICROSTEPS      128
-    #define K_OVERCURRENT    2000
-    #define K_STALLCURRENT   1500
-    #define K_MAX_VOLTAGE     127
-    #define K_CHAIN_POS        -1
-    #define K_SLEW_RATE         1
-  #endif
-
-  #if AXIS_IS_L64XX(U)
-    #define U_MICROSTEPS      128
-    #define U_OVERCURRENT    2000
-    #define U_STALLCURRENT   1500
-    #define U_MAX_VOLTAGE     127
-    #define U_CHAIN_POS        -1
-    #define U_SLEW_RATE         1
-  #endif
-
-  #if AXIS_IS_L64XX(V)
-    #define V_MICROSTEPS      128
-    #define V_OVERCURRENT    2000
-    #define V_STALLCURRENT   1500
-    #define V_MAX_VOLTAGE     127
-    #define V_CHAIN_POS        -1
-    #define V_SLEW_RATE         1
-  #endif
-
-  #if AXIS_IS_L64XX(W)
-    #define W_MICROSTEPS      128
-    #define W_OVERCURRENT    2000
-    #define W_STALLCURRENT   1500
-    #define W_MAX_VOLTAGE     127
-    #define W_CHAIN_POS        -1
-    #define W_SLEW_RATE         1
-  #endif
-
-  #if AXIS_IS_L64XX(E0)
-    #define E0_MICROSTEPS              128
-    #define E0_OVERCURRENT            2000
-    #define E0_STALLCURRENT           1500
-    #define E0_MAX_VOLTAGE             127
-    #define E0_CHAIN_POS                -1
-    #define E0_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E1)
-    #define E1_MICROSTEPS    E0_MICROSTEPS
-    #define E1_OVERCURRENT            2000
-    #define E1_STALLCURRENT           1500
-    #define E1_MAX_VOLTAGE             127
-    #define E1_CHAIN_POS                -1
-    #define E1_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E2)
-    #define E2_MICROSTEPS    E0_MICROSTEPS
-    #define E2_OVERCURRENT            2000
-    #define E2_STALLCURRENT           1500
-    #define E2_MAX_VOLTAGE             127
-    #define E2_CHAIN_POS                -1
-    #define E2_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E3)
-    #define E3_MICROSTEPS    E0_MICROSTEPS
-    #define E3_OVERCURRENT            2000
-    #define E3_STALLCURRENT           1500
-    #define E3_MAX_VOLTAGE             127
-    #define E3_CHAIN_POS                -1
-    #define E3_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E4)
-    #define E4_MICROSTEPS    E0_MICROSTEPS
-    #define E4_OVERCURRENT            2000
-    #define E4_STALLCURRENT           1500
-    #define E4_MAX_VOLTAGE             127
-    #define E4_CHAIN_POS                -1
-    #define E4_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E5)
-    #define E5_MICROSTEPS    E0_MICROSTEPS
-    #define E5_OVERCURRENT            2000
-    #define E5_STALLCURRENT           1500
-    #define E5_MAX_VOLTAGE             127
-    #define E5_CHAIN_POS                -1
-    #define E5_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E6)
-    #define E6_MICROSTEPS    E0_MICROSTEPS
-    #define E6_OVERCURRENT            2000
-    #define E6_STALLCURRENT           1500
-    #define E6_MAX_VOLTAGE             127
-    #define E6_CHAIN_POS                -1
-    #define E6_SLEW_RATE                 1
-  #endif
-
-  #if AXIS_IS_L64XX(E7)
-    #define E7_MICROSTEPS    E0_MICROSTEPS
-    #define E7_OVERCURRENT            2000
-    #define E7_STALLCURRENT           1500
-    #define E7_MAX_VOLTAGE             127
-    #define E7_CHAIN_POS                -1
-    #define E7_SLEW_RATE                 1
-  #endif
-
-  /**
-   * Monitor L6470 drivers for error conditions like over temperature and over current.
-   * In the case of over temperature Marlin can decrease the drive until the error condition clears.
-   * Other detected conditions can be used to stop the current print.
-   * Relevant G-codes:
-   * M906 - I1/2/3/4/5  Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given.
-   *         I not present or I0 or I1 - X, Y, Z or E0
-   *         I2 - X2, Y2, Z2 or E1
-   *         I3 - Z3 or E3
-   *         I4 - Z4 or E4
-   *         I5 - E5
-   * M916 - Increase drive level until get thermal warning
-   * M917 - Find minimum current thresholds
-   * M918 - Increase speed until max or error
-   * M122 S0/1 - Report driver parameters
-   */
-  //#define MONITOR_L6470_DRIVER_STATUS
-
-  #if ENABLED(MONITOR_L6470_DRIVER_STATUS)
-    #define KVAL_HOLD_STEP_DOWN     1
-    //#define L6470_STOP_ON_ERROR
-  #endif
-
-#endif // HAS_L64XX
 
 // @section i2cbus
 

Marlin/src/HAL/shared/HAL_spi_L6470.cpp

@@ -1,139 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
-/**
- * Software L6470 SPI functions originally from Arduino Sd2Card Library
- * Copyright (c) 2009 by William Greiman
- */
-
-#include "../../inc/MarlinConfig.h"
-
-#if HAS_L64XX
-
-#include "Delay.h"
-
-#include "../../core/serial.h"
-#include "../../libs/L64XX/L64XX_Marlin.h"
-
-// Make sure GCC optimizes this file.
-// Note that this line triggers a bug in GCC which is fixed by casting.
-// See the note below.
-#pragma GCC optimize (3)
-
-// run at ~4Mhz
-inline uint8_t L6470_SpiTransfer_Mode_0(uint8_t b) { // using Mode 0
-  for (uint8_t bits = 8; bits--;) {
-    WRITE(L6470_CHAIN_MOSI_PIN, b & 0x80);
-    b <<= 1;        // little setup time
-
-    WRITE(L6470_CHAIN_SCK_PIN, HIGH);
-    DELAY_NS(125);  // 10 cycles @ 84mhz
-
-    b |= (READ(L6470_CHAIN_MISO_PIN) != 0);
-
-    WRITE(L6470_CHAIN_SCK_PIN, LOW);
-    DELAY_NS(125);  // 10 cycles @ 84mhz
-  }
-  return b;
-}
-
-inline uint8_t L6470_SpiTransfer_Mode_3(uint8_t b) { // using Mode 3
-  for (uint8_t bits = 8; bits--;) {
-    WRITE(L6470_CHAIN_SCK_PIN, LOW);
-    WRITE(L6470_CHAIN_MOSI_PIN, b & 0x80);
-
-    DELAY_NS(125);  // 10 cycles @ 84mhz
-    WRITE(L6470_CHAIN_SCK_PIN, HIGH);
-    DELAY_NS(125);  // Need more delay for fast CPUs
-
-    b <<= 1;        // little setup time
-    b |= (READ(L6470_CHAIN_MISO_PIN) != 0);
-  }
-  DELAY_NS(125);    // 10 cycles @ 84mhz
-  return b;
-}
-
-/**
- * L64XX methods for SPI init and transfer
- */
-void L64XX_Marlin::spi_init() {
-  OUT_WRITE(L6470_CHAIN_SS_PIN, HIGH);
-  OUT_WRITE(L6470_CHAIN_SCK_PIN, HIGH);
-  OUT_WRITE(L6470_CHAIN_MOSI_PIN, HIGH);
-  SET_INPUT(L6470_CHAIN_MISO_PIN);
-
-  #if PIN_EXISTS(L6470_BUSY)
-    SET_INPUT(L6470_BUSY_PIN);
-  #endif
-
-  OUT_WRITE(L6470_CHAIN_MOSI_PIN, HIGH);
-}
-
-uint8_t L64XX_Marlin::transfer_single(uint8_t data, int16_t ss_pin) {
-  // First device in chain has data sent last
-  extDigitalWrite(ss_pin, LOW);
-
-  hal.isr_off();  // Disable interrupts during SPI transfer (can't allow partial command to chips)
-  const uint8_t data_out = L6470_SpiTransfer_Mode_3(data);
-  hal.isr_on();   // Enable interrupts
-
-  extDigitalWrite(ss_pin, HIGH);
-  return data_out;
-}
-
-uint8_t L64XX_Marlin::transfer_chain(uint8_t data, int16_t ss_pin, uint8_t chain_position) {
-  uint8_t data_out = 0;
-
-  // first device in chain has data sent last
-  extDigitalWrite(ss_pin, LOW);
-
-  for (uint8_t i = L64XX::chain[0]; !L64xxManager.spi_abort && i >= 1; i--) {   // Send data unless aborted
-    hal.isr_off();    // Disable interrupts during SPI transfer (can't allow partial command to chips)
-    const uint8_t temp = L6470_SpiTransfer_Mode_3(uint8_t(i == chain_position ? data : dSPIN_NOP));
-    hal.isr_on();     // Enable interrupts
-    if (i == chain_position) data_out = temp;
-  }
-
-  extDigitalWrite(ss_pin, HIGH);
-  return data_out;
-}
-
-/**
- * Platform-supplied L6470 buffer transfer method
- */
-void L64XX_Marlin::transfer(uint8_t L6470_buf[], const uint8_t length) {
-  // First device in chain has its data sent last
-
-  if (spi_active) {                   // Interrupted SPI transfer so need to
-    WRITE(L6470_CHAIN_SS_PIN, HIGH);  //  guarantee min high of 650ns
-    DELAY_US(1);
-  }
-
-  WRITE(L6470_CHAIN_SS_PIN, LOW);
-  for (uint8_t i = length; i >= 1; i--)
-    L6470_SpiTransfer_Mode_3(uint8_t(L6470_buf[i]));
-  WRITE(L6470_CHAIN_SS_PIN, HIGH);
-}
-
-#pragma GCC reset_options
-
-#endif // HAS_L64XX

Marlin/src/MarlinCore.cpp

@@ -226,10 +226,6 @@
   #include "feature/mmu/mmu2.h"
 #endif
 
-#if HAS_L64XX
-  #include "libs/L64XX/L64XX_Marlin.h"
-#endif
-
 #if ENABLED(PASSWORD_FEATURE)
   #include "feature/password/password.h"
 #endif
@@ -432,7 +428,7 @@ inline void manage_inactivity(const bool no_stepper_sleep=false) {
 
       if (!has_blocks && !do_reset_timeout && gcode.stepper_inactive_timeout()) {
         if (!already_shutdown_steppers) {
-          already_shutdown_steppers = true;  // L6470 SPI will consume 99% of free time without this
+          already_shutdown_steppers = true;
 
           // Individual axes will be disabled if configured
           TERN_(DISABLE_INACTIVE_X, stepper.disable_axis(X_AXIS));
@@ -731,8 +727,6 @@ inline void manage_inactivity(const bool no_stepper_sleep=false) {
 
   TERN_(MONITOR_DRIVER_STATUS, monitor_tmc_drivers());
 
-  TERN_(MONITOR_L6470_DRIVER_STATUS, L64xxManager.monitor_driver());
-
   // Limit check_axes_activity frequency to 10Hz
   static millis_t next_check_axes_ms = 0;
   if (ELAPSED(ms, next_check_axes_ms)) {
@@ -1062,7 +1056,6 @@ inline void tmc_standby_setup() {
  *    • TMC220x Stepper Drivers (Serial)
  *    • PSU control
  *    • Power-loss Recovery
- *    • L64XX Stepper Drivers (SPI)
  *    • Stepper Driver Reset: DISABLE
  *    • TMC Stepper Drivers (SPI)
  *    • Run hal.init_board() for additional pins setup
@@ -1251,10 +1244,6 @@ void setup() {
     SETUP_RUN(tmc_init_cs_pins());
   #endif
 
-  #if HAS_L64XX
-    SETUP_RUN(L64xxManager.init());  // Set up SPI, init drivers
-  #endif
-
   #if ENABLED(PSU_CONTROL)
     SETUP_LOG("PSU_CONTROL");
     powerManager.init();

Marlin/src/core/boards.h

@@ -385,7 +385,6 @@
 #define BOARD_RUMBA32_BTT             4204  // RUMBA32 STM32F446VE based controller from BIGTREETECH
 #define BOARD_BLACK_STM32F407VE       4205  // BLACK_STM32F407VE
 #define BOARD_BLACK_STM32F407ZE       4206  // BLACK_STM32F407ZE
-#define BOARD_STEVAL_3DP001V1         4207  // STEVAL-3DP001V1 3D PRINTER BOARD
 #define BOARD_BTT_SKR_PRO_V1_1        4208  // BigTreeTech SKR Pro v1.1 (STM32F407ZG)
 #define BOARD_BTT_SKR_PRO_V1_2        4209  // BigTreeTech SKR Pro v1.2 (STM32F407ZG)
 #define BOARD_BTT_BTT002_V1_0         4210  // BigTreeTech BTT002 v1.0 (STM32F407VG)

Marlin/src/core/drivers.h

@@ -30,10 +30,6 @@
 #define _A5984              0x5984
 #define _DRV8825            0x8825
 #define _LV8729             0x8729
-#define _L6470              0x6470
-#define _L6474              0x6474
-#define _L6480              0x6480
-#define _POWERSTEP01        0xF00D
 #define _TB6560             0x6560
 #define _TB6600             0x6600
 #define _TMC2100            0x2100
@@ -193,16 +189,3 @@
 #if HAS_DRIVER(TMC26X)
   #define HAS_TMC26X 1
 #endif
-
-//
-// L64XX Stepper Drivers
-//
-
-#if HAS_DRIVER(L6470) || HAS_DRIVER(L6474) || HAS_DRIVER(L6480) || HAS_DRIVER(POWERSTEP01)
-  #define HAS_L64XX 1
-#endif
-#if HAS_L64XX && !HAS_DRIVER(L6474)
-  #define HAS_L64XX_NOT_L6474 1
-#endif
-
-#define AXIS_IS_L64XX(A) (AXIS_DRIVER_TYPE_##A(L6470) || AXIS_DRIVER_TYPE_##A(L6474) || AXIS_DRIVER_TYPE_##A(L6480) || AXIS_DRIVER_TYPE_##A(POWERSTEP01))

Marlin/src/gcode/calibrate/G28.cpp

@@ -55,10 +55,6 @@
   #include "../../lcd/e3v2/proui/dwin.h"
 #endif
 
-#if HAS_L64XX                         // set L6470 absolute position registers to counts
-  #include "../../libs/L64XX/L64XX_Marlin.h"
-#endif
-
 #if ENABLED(LASER_FEATURE)
   #include "../../feature/spindle_laser.h"
 #endif
@@ -601,20 +597,4 @@ void GcodeSuite::G28() {
 
   TERN_(FULL_REPORT_TO_HOST_FEATURE, set_and_report_grblstate(old_grblstate));
 
-  #if HAS_L64XX
-    // Set L6470 absolute position registers to counts
-    // constexpr *might* move this to PROGMEM.
-    // If not, this will need a PROGMEM directive and an accessor.
-    #define _EN_ITEM(N) , E_AXIS
-    static constexpr AxisEnum L64XX_axis_xref[MAX_L64XX] = {
-      NUM_AXIS_LIST(X_AXIS, Y_AXIS, Z_AXIS, I_AXIS, J_AXIS, K_AXIS, U_AXIS, V_AXIS, W_AXIS),
-      X_AXIS, Y_AXIS, Z_AXIS, Z_AXIS, Z_AXIS
-      REPEAT(E_STEPPERS, _EN_ITEM)
-    };
-    #undef _EN_ITEM
-    for (uint8_t j = 1; j <= L64XX::chain[0]; j++) {
-      const uint8_t cv = L64XX::chain[j];
-      L64xxManager.set_param((L64XX_axis_t)cv, L6470_ABS_POS, stepper.position(L64XX_axis_xref[cv]));
-    }
-  #endif
 }

Marlin/src/gcode/feature/L6470/M122.cpp

@@ -1,151 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
-#include "../../../inc/MarlinConfig.h"
-
-#if HAS_L64XX
-
-#include "../../gcode.h"
-#include "../../../libs/L64XX/L64XX_Marlin.h"
-#include "../../../module/stepper/indirection.h"
-
-void echo_yes_no(const bool yes);
-
-inline void L6470_say_status(const L64XX_axis_t axis) {
-  if (L64xxManager.spi_abort) return;
-  const L64XX_Marlin::L64XX_shadow_t &sh = L64xxManager.shadow;
-  L64xxManager.get_status(axis);
-  L64xxManager.say_axis(axis);
-  #if ENABLED(L6470_CHITCHAT)
-    char temp_buf[20];
-    sprintf_P(temp_buf, PSTR("   status: %4x   "), sh.STATUS_AXIS_RAW);
-    SERIAL_ECHO(temp_buf);
-    print_bin(sh.STATUS_AXIS_RAW);
-    switch (sh.STATUS_AXIS_LAYOUT) {
-      case L6470_STATUS_LAYOUT: SERIAL_ECHOPGM("   L6470"); break;
-      case L6474_STATUS_LAYOUT: SERIAL_ECHOPGM("   L6474"); break;
-      case L6480_STATUS_LAYOUT: SERIAL_ECHOPGM("   L6480/powerSTEP01"); break;
-    }
-  #endif
-  SERIAL_ECHOPGM("\n...OUTPUT: ");
-  SERIAL_ECHOF(sh.STATUS_AXIS & STATUS_HIZ ? F("OFF") : F("ON "));
-  SERIAL_ECHOPGM("   BUSY: "); echo_yes_no((sh.STATUS_AXIS & STATUS_BUSY) == 0);
-  SERIAL_ECHOPGM("   DIR: ");
-  SERIAL_ECHOF((((sh.STATUS_AXIS & STATUS_DIR) >> 4) ^ L64xxManager.index_to_dir[axis]) ? F("FORWARD") : F("REVERSE"));
-  if (sh.STATUS_AXIS_LAYOUT == L6480_STATUS_LAYOUT) {
-    SERIAL_ECHOPGM("   Last Command: ");
-    if (sh.STATUS_AXIS & sh.STATUS_AXIS_WRONG_CMD) SERIAL_ECHOPGM("VALID");
-    else                                           SERIAL_ECHOPGM("ERROR");
-    SERIAL_ECHOPGM("\n...THERMAL: ");
-    switch ((sh.STATUS_AXIS & (sh.STATUS_AXIS_TH_SD | sh.STATUS_AXIS_TH_WRN)) >> 11) {
-      case 0: SERIAL_ECHOPGM("DEVICE SHUTDOWN"); break;
-      case 1: SERIAL_ECHOPGM("BRIDGE SHUTDOWN"); break;
-      case 2: SERIAL_ECHOPGM("WARNING        "); break;
-      case 3: SERIAL_ECHOPGM("OK             "); break;
-    }
-  }
-  else {
-    SERIAL_ECHOPGM("   Last Command: ");
-    if (!(sh.STATUS_AXIS & sh.STATUS_AXIS_WRONG_CMD)) SERIAL_ECHOPGM("IN");
-    SERIAL_ECHOPGM("VALID    ");
-    SERIAL_ECHOF(sh.STATUS_AXIS & sh.STATUS_AXIS_NOTPERF_CMD ?  F("COMPLETED    ") : F("Not PERFORMED"));
-    SERIAL_ECHOPGM("\n...THERMAL: ", !(sh.STATUS_AXIS & sh.STATUS_AXIS_TH_SD) ? "SHUTDOWN       " : !(sh.STATUS_AXIS & sh.STATUS_AXIS_TH_WRN) ? "WARNING        " : "OK             ");
-  }
-  SERIAL_ECHOPGM("   OVERCURRENT:"); echo_yes_no((sh.STATUS_AXIS & sh.STATUS_AXIS_OCD) == 0);
-  if (sh.STATUS_AXIS_LAYOUT != L6474_STATUS_LAYOUT) {
-    SERIAL_ECHOPGM("   STALL:"); echo_yes_no((sh.STATUS_AXIS & sh.STATUS_AXIS_STEP_LOSS_A) == 0 || (sh.STATUS_AXIS & sh.STATUS_AXIS_STEP_LOSS_B) == 0);
-    SERIAL_ECHOPGM("   STEP-CLOCK MODE:"); echo_yes_no((sh.STATUS_AXIS & sh.STATUS_AXIS_SCK_MOD) != 0);
-  }
-  else {
-    SERIAL_ECHOPGM("   STALL: NA "
-                   "   STEP-CLOCK MODE: NA"
-                   "   UNDER VOLTAGE LOCKOUT: "); echo_yes_no((sh.STATUS_AXIS & sh.STATUS_AXIS_UVLO) == 0);
-  }
-  SERIAL_EOL();
-}
-
-/**
- * M122: Debug L6470 drivers
- */
-void GcodeSuite::M122() {
-  L64xxManager.pause_monitor(true); // Keep monitor_driver() from stealing status
-  L64xxManager.spi_active = true;   // Tell set_directions() a series of SPI transfers is underway
-
-  //if (parser.seen('S'))
-  //  tmc_set_report_interval(parser.value_bool());
-  //else
-
-  #if AXIS_IS_L64XX(X)
-    L6470_say_status(X);
-  #endif
-  #if AXIS_IS_L64XX(X2)
-    L6470_say_status(X2);
-  #endif
-  #if AXIS_IS_L64XX(Y)
-    L6470_say_status(Y);
-  #endif
-  #if AXIS_IS_L64XX(Y2)
-    L6470_say_status(Y2);
-  #endif
-  #if AXIS_IS_L64XX(Z)
-    L6470_say_status(Z);
-  #endif
-  #if AXIS_IS_L64XX(Z2)
-    L6470_say_status(Z2);
-  #endif
-  #if AXIS_IS_L64XX(Z3)
-    L6470_say_status(Z3);
-  #endif
-  #if AXIS_IS_L64XX(Z4)
-    L6470_say_status(Z4);
-  #endif
-  #if AXIS_IS_L64XX(E0)
-    L6470_say_status(E0);
-  #endif
-  #if AXIS_IS_L64XX(E1)
-    L6470_say_status(E1);
-  #endif
-  #if AXIS_IS_L64XX(E2)
-    L6470_say_status(E2);
-  #endif
-  #if AXIS_IS_L64XX(E3)
-    L6470_say_status(E3);
-  #endif
-  #if AXIS_IS_L64XX(E4)
-    L6470_say_status(E4);
-  #endif
-  #if AXIS_IS_L64XX(E5)
-    L6470_say_status(E5);
-  #endif
-  #if AXIS_IS_L64XX(E6)
-    L6470_say_status(E6);
-  #endif
-  #if AXIS_IS_L64XX(E7)
-    L6470_say_status(E7);
-  #endif
-
-  L64xxManager.spi_active = false;   // done with all SPI transfers - clear handshake flags
-  L64xxManager.spi_abort = false;
-  L64xxManager.pause_monitor(false);
-}
-
-#endif // HAS_L64XX

Marlin/src/gcode/feature/L6470/M906.cpp

@@ -1,417 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
-#include "../../../inc/MarlinConfig.h"
-
-#if HAS_L64XX
-
-#if AXIS_COLLISION('I')
-  #error "M906 parameter 'I' collision with axis name."
-#endif
-
-#include "../../gcode.h"
-#include "../../../libs/L64XX/L64XX_Marlin.h"
-#include "../../../module/stepper/indirection.h"
-#include "../../../module/planner.h"
-
-#define DEBUG_OUT ENABLED(L6470_CHITCHAT)
-#include "../../../core/debug_out.h"
-
-/**
- * MACRO to fetch information on the items associated with current limiting
- * and maximum voltage output.
- *
- * L6470 can be setup to shutdown if either current threshold is exceeded.
- *
- * L6470 output current can not be set directly.  It is set indirectly by
- * setting the maximum effective output voltage.
- *
- *  Effective output voltage is set by PWM duty cycle.
- *
- *  Maximum effective output voltage is affected by MANY variables.  The main ones are:
- *    KVAL_HOLD
- *    KVAL_RUN
- *    KVAL_ACC
- *    KVAL_DEC
- *    Vs compensation (if enabled)
- */
-void L64XX_report_current(L64XX &motor, const L64XX_axis_t axis) {
-
-  if (L64xxManager.spi_abort) return;  // don't do anything if set_directions() has occurred
-
-  const L64XX_Marlin::L64XX_shadow_t &sh = L64xxManager.shadow;
-  const uint16_t status = L64xxManager.get_status(axis);    //also populates shadow structure
-  const uint8_t OverCurrent_Threshold = uint8_t(motor.GetParam(L6470_OCD_TH));
-
-  auto say_axis_status = [](const L64XX_axis_t axis, const uint16_t status) {
-    L64xxManager.say_axis(axis);
-    #if ENABLED(L6470_CHITCHAT)
-      char tmp[10];
-      sprintf_P(tmp, PSTR("%4x   "), status);
-      DEBUG_ECHOPGM("   status: ", tmp);
-      print_bin(status);
-    #else
-      UNUSED(status);
-    #endif
-    SERIAL_EOL();
-  };
-
-  char temp_buf[10];
-
-  switch (sh.STATUS_AXIS_LAYOUT) {
-    case L6470_STATUS_LAYOUT:       // L6470
-    case L6480_STATUS_LAYOUT: {     // L6480 & powerstep01
-      const uint16_t Stall_Threshold = (uint8_t)motor.GetParam(L6470_STALL_TH),
-                     motor_status = (status & (STATUS_MOT_STATUS)) >> 5,
-                     L6470_ADC_out = motor.GetParam(L6470_ADC_OUT),
-                     L6470_ADC_out_limited = constrain(L6470_ADC_out, 8, 24);
-      const float comp_coef = 1600.0f / L6470_ADC_out_limited;
-      const uint16_t MicroSteps = _BV(motor.GetParam(L6470_STEP_MODE) & 0x07);
-
-      say_axis_status(axis, sh.STATUS_AXIS_RAW);
-
-      SERIAL_ECHOPGM("...OverCurrent Threshold: ");
-      sprintf_P(temp_buf, PSTR("%2d ("), OverCurrent_Threshold);
-      SERIAL_ECHO(temp_buf);
-      SERIAL_ECHO((OverCurrent_Threshold + 1) * motor.OCD_CURRENT_CONSTANT_INV);
-      SERIAL_ECHOPGM(" mA)");
-      SERIAL_ECHOPGM("   Stall Threshold: ");
-      sprintf_P(temp_buf, PSTR("%2d ("), Stall_Threshold);
-      SERIAL_ECHO(temp_buf);
-      SERIAL_ECHO((Stall_Threshold + 1) * motor.STALL_CURRENT_CONSTANT_INV);
-      SERIAL_ECHOPGM(" mA)");
-      SERIAL_ECHOPGM("   Motor Status: ");
-      switch (motor_status) {
-        case 0: SERIAL_ECHOPGM("stopped"); break;
-        case 1: SERIAL_ECHOPGM("accelerating"); break;
-        case 2: SERIAL_ECHOPGM("decelerating"); break;
-        case 3: SERIAL_ECHOPGM("at constant speed"); break;
-      }
-      SERIAL_EOL();
-
-      SERIAL_ECHOPGM("...MicroSteps: ", MicroSteps,
-                      "   ADC_OUT: ", L6470_ADC_out);
-      SERIAL_ECHOPGM("   Vs_compensation: ");
-      SERIAL_ECHOF((motor.GetParam(sh.L6470_AXIS_CONFIG) & CONFIG_EN_VSCOMP) ? F("ENABLED ") : F("DISABLED"));
-      SERIAL_ECHOLNPGM("   Compensation coefficient: ~", comp_coef * 0.01f);
-
-      SERIAL_ECHOPGM("...KVAL_HOLD: ", motor.GetParam(L6470_KVAL_HOLD),
-                      "   KVAL_RUN : ", motor.GetParam(L6470_KVAL_RUN),
-                      "   KVAL_ACC: ", motor.GetParam(L6470_KVAL_ACC),
-                      "   KVAL_DEC: ", motor.GetParam(L6470_KVAL_DEC),
-                      "   V motor max = ");
-      switch (motor_status) {
-        case 0: SERIAL_ECHO(motor.GetParam(L6470_KVAL_HOLD) * 100 / 256); SERIAL_ECHOPGM("% (KVAL_HOLD)"); break;
-        case 1: SERIAL_ECHO(motor.GetParam(L6470_KVAL_RUN)  * 100 / 256); SERIAL_ECHOPGM("% (KVAL_RUN)"); break;
-        case 2: SERIAL_ECHO(motor.GetParam(L6470_KVAL_ACC)  * 100 / 256); SERIAL_ECHOPGM("% (KVAL_ACC)"); break;
-        case 3: SERIAL_ECHO(motor.GetParam(L6470_KVAL_DEC)  * 100 / 256); SERIAL_ECHOPGM("% (KVAL_HOLD)"); break;
-      }
-      SERIAL_EOL();
-
-      #if ENABLED(L6470_CHITCHAT)
-        DEBUG_ECHOPGM("...SLEW RATE: ");
-        switch (sh.STATUS_AXIS_LAYOUT) {
-          case L6470_STATUS_LAYOUT: {
-            switch ((motor.GetParam(sh.L6470_AXIS_CONFIG) & CONFIG_POW_SR) >> CONFIG_POW_SR_BIT) {
-              case 0: { DEBUG_ECHOLNPGM("320V/uS") ; break; }
-              case 1: { DEBUG_ECHOLNPGM("75V/uS")  ; break; }
-              case 2: { DEBUG_ECHOLNPGM("110V/uS") ; break; }
-              case 3: { DEBUG_ECHOLNPGM("260V/uS") ; break; }
-            }
-            break;
-          }
-        case L6480_STATUS_LAYOUT: {
-            switch (motor.GetParam(L6470_GATECFG1) & CONFIG1_SR ) {
-              case CONFIG1_SR_220V_us: { DEBUG_ECHOLNPGM("220V/uS") ; break; }
-              case CONFIG1_SR_400V_us: { DEBUG_ECHOLNPGM("400V/uS") ; break; }
-              case CONFIG1_SR_520V_us: { DEBUG_ECHOLNPGM("520V/uS") ; break; }
-              case CONFIG1_SR_980V_us: { DEBUG_ECHOLNPGM("980V/uS") ; break; }
-              default: { DEBUG_ECHOLNPGM("unknown") ; break; }
-            }
-          }
-        }
-      #endif
-      SERIAL_EOL();
-      break;
-    }
-
-    case L6474_STATUS_LAYOUT: {  // L6474
-      const uint16_t L6470_ADC_out = motor.GetParam(L6470_ADC_OUT) & 0x1F,
-                     L6474_TVAL_val = motor.GetParam(L6474_TVAL) & 0x7F;
-
-      say_axis_status(axis, sh.STATUS_AXIS_RAW);
-
-      SERIAL_ECHOPGM("...OverCurrent Threshold: ");
-      sprintf_P(temp_buf, PSTR("%2d ("), OverCurrent_Threshold);
-      SERIAL_ECHO(temp_buf);
-      SERIAL_ECHO((OverCurrent_Threshold + 1) * motor.OCD_CURRENT_CONSTANT_INV);
-      SERIAL_ECHOPGM(" mA)");
-      SERIAL_ECHOPGM("   TVAL: ");
-      sprintf_P(temp_buf, PSTR("%2d ("), L6474_TVAL_val);
-      SERIAL_ECHO(temp_buf);
-      SERIAL_ECHO((L6474_TVAL_val + 1) * motor.STALL_CURRENT_CONSTANT_INV);
-      SERIAL_ECHOLNPGM(" mA)   Motor Status: NA");
-
-      const uint16_t MicroSteps = _BV(motor.GetParam(L6470_STEP_MODE) & 0x07); //NOMORE(MicroSteps, 16);
-      SERIAL_ECHOPGM("...MicroSteps: ", MicroSteps,
-                      "   ADC_OUT: ", L6470_ADC_out);
-
-      SERIAL_ECHOLNPGM("   Vs_compensation: NA\n");
-      SERIAL_ECHOLNPGM("...KVAL_HOLD: NA"
-                       "   KVAL_RUN : NA"
-                       "   KVAL_ACC: NA"
-                       "   KVAL_DEC: NA"
-                       "   V motor max =  NA");
-
-      #if ENABLED(L6470_CHITCHAT)
-        DEBUG_ECHOPGM("...SLEW RATE: ");
-        switch ((motor.GetParam(sh.L6470_AXIS_CONFIG) & CONFIG_POW_SR) >> CONFIG_POW_SR_BIT) {
-          case 0:  DEBUG_ECHOLNPGM("320V/uS") ; break;
-          case 1:  DEBUG_ECHOLNPGM("75V/uS")  ; break;
-          case 2:  DEBUG_ECHOLNPGM("110V/uS") ; break;
-          case 3:  DEBUG_ECHOLNPGM("260V/uS") ; break;
-          default: DEBUG_ECHOLNPGM("slew rate: ", (motor.GetParam(sh.L6470_AXIS_CONFIG) & CONFIG_POW_SR) >> CONFIG_POW_SR_BIT); break;
-        }
-      #endif
-      SERIAL_EOL();
-      SERIAL_EOL();
-      break;
-    }
-  }
-}
-
-/**
- * M906: report or set KVAL_HOLD which sets the maximum effective voltage provided by the
- *       PWMs to the steppers
- *
- * On L6474 this sets the TVAL register (same address).
- *
- * I - select which driver(s) to change on multi-driver axis
- *         (default) all drivers on the axis
- *     0 - monitor only the first XYZ... driver
- *     1 - monitor only X2, Y2, Z2
- *     2 - monitor only Z3
- *     3 - monitor only Z4
- * Xxxx, Yxxx, Zxxx, Axxx, Bxxx, Cxxx, Uxxx, Vxxx, Wxxx, Exxx - axis to change (optional)
- *     L6474 - current in mA (4A max)
- *     All others - 0-255
- *
- * Sets KVAL_HOLD which affects the current being driven through the stepper.
- *
- * L6470 is used in the STEP-CLOCK mode.  KVAL_HOLD is the only KVAL_xxx
- * that affects the effective voltage seen by the stepper.
- */
-void GcodeSuite::M906() {
-
-  L64xxManager.pause_monitor(true); // Keep monitor_driver() from stealing status
-
-  #define L6470_SET_KVAL_HOLD(Q) (AXIS_IS_L64XX(Q) ? stepper##Q.setTVALCurrent(value) : stepper##Q.SetParam(L6470_KVAL_HOLD, uint8_t(value)))
-
-  DEBUG_ECHOLNPGM("M906");
-
-  uint8_t report_current = true;
-
-  #if AXIS_IS_L64XX(X2) || AXIS_IS_L64XX(Y2) || AXIS_IS_L64XX(Z2) || AXIS_IS_L64XX(Z3) || AXIS_IS_L64XX(Z4)
-    const int8_t index = parser.byteval('I', -1);
-  #else
-    constexpr int8_t index = -1;
-  #endif
-
-  LOOP_LOGICAL_AXES(i) if (uint16_t value = parser.intval(AXIS_CHAR(i))) {
-
-    report_current = false;
-
-    if (planner.has_blocks_queued() || planner.cleaning_buffer_counter) {
-      SERIAL_ECHOLNPGM("Test aborted. Can't set KVAL_HOLD while steppers are moving.");
-      return;
-    }
-
-    switch (i) {
-      #if AXIS_IS_L64XX(X) || AXIS_IS_L64XX(X2)
-        case X_AXIS:
-          #if AXIS_IS_L64XX(X)
-            if (index < 0 || index == 0) L6470_SET_KVAL_HOLD(X);
-          #endif
-          #if AXIS_IS_L64XX(X2)
-            if (index < 0 || index == 1) L6470_SET_KVAL_HOLD(X2);
-          #endif
-          break;
-      #endif
-
-      #if AXIS_IS_L64XX(Y) || AXIS_IS_L64XX(Y2)
-        case Y_AXIS:
-          #if AXIS_IS_L64XX(Y)
-            if (index < 0 || index == 0) L6470_SET_KVAL_HOLD(Y);
-          #endif
-          #if AXIS_IS_L64XX(Y2)
-            if (index < 0 || index == 1) L6470_SET_KVAL_HOLD(Y2);
-          #endif
-          break;
-      #endif
-
-      #if AXIS_IS_L64XX(Z) || AXIS_IS_L64XX(Z2) || AXIS_IS_L64XX(Z3) || AXIS_IS_L64XX(Z4)
-        case Z_AXIS:
-          #if AXIS_IS_L64XX(Z)
-            if (index < 0 || index == 0) L6470_SET_KVAL_HOLD(Z);
-          #endif
-          #if AXIS_IS_L64XX(Z2)
-            if (index < 0 || index == 1) L6470_SET_KVAL_HOLD(Z2);
-          #endif
-          #if AXIS_IS_L64XX(Z3)
-            if (index < 0 || index == 2) L6470_SET_KVAL_HOLD(Z3);
-          #endif
-          #if AXIS_IS_L64XX(Z4)
-            if (index < 0 || index == 3) L6470_SET_KVAL_HOLD(Z4);
-          #endif
-          break;
-      #endif
-
-      #if AXIS_IS_L64XX(I)
-        case I_AXIS: L6470_SET_KVAL_HOLD(I); break;
-      #endif
-      #if AXIS_IS_L64XX(J)
-        case J_AXIS: L6470_SET_KVAL_HOLD(J); break;
-      #endif
-      #if AXIS_IS_L64XX(K)
-        case K_AXIS: L6470_SET_KVAL_HOLD(K); break;
-      #endif
-      #if AXIS_IS_L64XX(U)
-        case U_AXIS: L6470_SET_KVAL_HOLD(U); break;
-      #endif
-      #if AXIS_IS_L64XX(V)
-        case V_AXIS: L6470_SET_KVAL_HOLD(V); break;
-      #endif
-      #if AXIS_IS_L64XX(W)
-        case W_AXIS: L6470_SET_KVAL_HOLD(W); break;
-      #endif
-
-      #if AXIS_IS_L64XX(E0) || AXIS_IS_L64XX(E1) || AXIS_IS_L64XX(E2) || AXIS_IS_L64XX(E3) || AXIS_IS_L64XX(E4) || AXIS_IS_L64XX(E5) || AXIS_IS_L64XX(E6) || AXIS_IS_L64XX(E7)
-        case E_AXIS: {
-          const int8_t eindex = get_target_e_stepper_from_command(-2);
-          #if AXIS_IS_L64XX(E0)
-            if (eindex < 0 || eindex == 0) L6470_SET_KVAL_HOLD(E0);
-          #endif
-          #if AXIS_IS_L64XX(E1)
-            if (eindex < 0 || eindex == 1) L6470_SET_KVAL_HOLD(E1);
-          #endif
-          #if AXIS_IS_L64XX(E2)
-            if (eindex < 0 || eindex == 2) L6470_SET_KVAL_HOLD(E2);
-          #endif
-          #if AXIS_IS_L64XX(E3)
-            if (eindex < 0 || eindex == 3) L6470_SET_KVAL_HOLD(E3);
-          #endif
-          #if AXIS_IS_L64XX(E4)
-            if (eindex < 0 || eindex == 4) L6470_SET_KVAL_HOLD(E4);
-          #endif
-          #if AXIS_IS_L64XX(E5)
-            if (eindex < 0 || eindex == 5) L6470_SET_KVAL_HOLD(E5);
-          #endif
-          #if AXIS_IS_L64XX(E6)
-            if (eindex < 0 || eindex == 6) L6470_SET_KVAL_HOLD(E6);
-          #endif
-          #if AXIS_IS_L64XX(E7)
-            if (eindex < 0 || eindex == 7) L6470_SET_KVAL_HOLD(E7);
-          #endif
-        } break;
-      #endif
-    }
-  }
-
-  if (report_current) {
-    #define L64XX_REPORT_CURRENT(Q) L64XX_report_current(stepper##Q, Q)
-
-    L64xxManager.spi_active = true; // Tell set_directions() a series of SPI transfers is underway
-
-    #if AXIS_IS_L64XX(X)
-      L64XX_REPORT_CURRENT(X);
-    #endif
-    #if AXIS_IS_L64XX(X2)
-      L64XX_REPORT_CURRENT(X2);
-    #endif
-    #if AXIS_IS_L64XX(Y)
-      L64XX_REPORT_CURRENT(Y);
-    #endif
-    #if AXIS_IS_L64XX(Y2)
-      L64XX_REPORT_CURRENT(Y2);
-    #endif
-    #if AXIS_IS_L64XX(Z)
-      L64XX_REPORT_CURRENT(Z);
-    #endif
-    #if AXIS_IS_L64XX(Z2)
-      L64XX_REPORT_CURRENT(Z2);
-    #endif
-    #if AXIS_IS_L64XX(Z3)
-      L64XX_REPORT_CURRENT(Z3);
-    #endif
-    #if AXIS_IS_L64XX(Z4)
-      L64XX_REPORT_CURRENT(Z4);
-    #endif
-    #if AXIS_IS_L64XX(I)
-      L64XX_REPORT_CURRENT(I);
-    #endif
-    #if AXIS_IS_L64XX(J)
-      L64XX_REPORT_CURRENT(J);
-    #endif
-    #if AXIS_IS_L64XX(K)
-      L64XX_REPORT_CURRENT(K);
-    #endif
-    #if AXIS_IS_L64XX(U)
-      L64XX_REPORT_CURRENT(U);
-    #endif
-    #if AXIS_IS_L64XX(V)
-      L64XX_REPORT_CURRENT(V);
-    #endif
-    #if AXIS_IS_L64XX(W)
-      L64XX_REPORT_CURRENT(W);
-    #endif
-    #if AXIS_IS_L64XX(E0)
-      L64XX_REPORT_CURRENT(E0);
-    #endif
-    #if AXIS_IS_L64XX(E1)
-      L64XX_REPORT_CURRENT(E1);
-    #endif
-    #if AXIS_IS_L64XX(E2)
-      L64XX_REPORT_CURRENT(E2);
-    #endif
-    #if AXIS_IS_L64XX(E3)
-      L64XX_REPORT_CURRENT(E3);
-    #endif
-    #if AXIS_IS_L64XX(E4)
-      L64XX_REPORT_CURRENT(E4);
-    #endif
-    #if AXIS_IS_L64XX(E5)
-      L64XX_REPORT_CURRENT(E5);
-    #endif
-    #if AXIS_IS_L64XX(E6)
-      L64XX_REPORT_CURRENT(E6);
-    #endif
-    #if AXIS_IS_L64XX(E7)
-      L64XX_REPORT_CURRENT(E7);
-    #endif
-
-    L64xxManager.spi_active = false;   // done with all SPI transfers - clear handshake flags
-    L64xxManager.spi_abort = false;
-    L64xxManager.pause_monitor(false);
-  }
-}
-
-#endif // HAS_L64XX

Marlin/src/gcode/feature/L6470/M916-M918.cpp

@@ -1,650 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
-//
-// NOTE: All tests assume each axis uses matching driver chips.
-//
-
-#include "../../../inc/MarlinConfig.h"
-
-#if HAS_L64XX
-
-#include "../../gcode.h"
-#include "../../../module/stepper/indirection.h"
-#include "../../../module/planner.h"
-#include "../../../libs/L64XX/L64XX_Marlin.h"
-
-#define DEBUG_OUT ENABLED(L6470_CHITCHAT)
-#include "../../../core/debug_out.h"
-
-/**
- * M916: increase KVAL_HOLD until get thermal warning
- *       NOTE - on L6474 it is TVAL that is used
- *
- * J - select which driver(s) to monitor on multi-driver axis
- *     0 - (default) monitor all drivers on the axis or E0
- *     1 - monitor only X, Y, Z, E1
- *     2 - monitor only X2, Y2, Z2, E2
- *     3 - monitor only Z3, E3
- *     4 - monitor only Z4, E4
- *
- * Xxxx, Yxxx, Zxxx, Exxx - axis to be monitored with displacement
- *     xxx (1-255) is distance moved on either side of current position
- *
- * F - feedrate
- *     optional - will use default max feedrate from configuration.h if not specified
- *
- * T - current (mA) setting for TVAL (0 - 4A in 31.25mA increments, rounds down) - L6474 only
- *     optional - will report current value from driver if not specified
- *
- * K - value for KVAL_HOLD (0 - 255) (ignored for L6474)
- *     optional - will report current value from driver if not specified
- *
- * D - time (in seconds) to run each setting of KVAL_HOLD/TVAL
- *     optional - defaults to zero (runs each setting once)
- */
-
-/**
- * This routine is also useful for determining the approximate KVAL_HOLD
- * where the stepper stops losing steps. The sound will get noticeably quieter
- * as it stops losing steps.
- */
-
-void GcodeSuite::M916() {
-
-  DEBUG_ECHOLNPGM("M916");
-
-  L64xxManager.pause_monitor(true); // Keep monitor_driver() from stealing status
-
-  // Variables used by L64xxManager.get_user_input function - some may not be used
-  char axis_mon[3][3] = { {"  "}, {"  "}, {"  "} };   // list of Axes to be monitored
-  L64XX_axis_t axis_index[3];
-  uint16_t axis_status[3];
-  uint8_t driver_count = 1;
-  float position_max;
-  float position_min;
-  float final_feedrate;
-  uint8_t kval_hold;
-  uint8_t OCD_TH_val = 0;
-  uint8_t STALL_TH_val = 0;
-  uint16_t over_current_threshold;
-  constexpr uint8_t over_current_flag = false;  // M916 doesn't play with the overcurrent thresholds
-
-  #define DRIVER_TYPE_L6474(Q) AXIS_DRIVER_TYPE_##Q(L6474)
-
-  uint8_t j;   // general purpose counter
-
-  if (L64xxManager.get_user_input(driver_count, axis_index, axis_mon, position_max, position_min, final_feedrate, kval_hold, over_current_flag, OCD_TH_val, STALL_TH_val, over_current_threshold))
-    return;  // quit if invalid user input
-
-  DEBUG_ECHOLNPGM("feedrate = ", final_feedrate);
-
-  planner.synchronize();                             // wait for all current movement commands to complete
-
-  const L64XX_Marlin::L64XX_shadow_t &sh = L64xxManager.shadow;
-  for (j = 0; j < driver_count; j++)
-    L64xxManager.get_status(axis_index[j]);  // clear out any pre-existing error flags
-
-  char temp_axis_string[] = " ";
-  temp_axis_string[0] = axis_mon[0][0];  // need to have a string for use within sprintf format section
-  char gcode_string[80];
-  uint16_t status_composite = 0;
-
-  uint16_t M91x_counter = kval_hold;
-  uint16_t M91x_counter_max;
-  if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT) {
-    M91x_counter_max = 128;  // TVAL is 7 bits
-    LIMIT(M91x_counter, 0U, 127U);
-  }
-  else
-    M91x_counter_max = 256;  // KVAL_HOLD is 8 bits
-
-  uint8_t M91x_delay_s = parser.byteval('D');   // get delay in seconds
-  millis_t M91x_delay_ms = SEC_TO_MS(M91x_delay_s * 60);
-  millis_t M91x_delay_end;
-
-  DEBUG_ECHOLNPGM(".\n.");
-
-  do {
-
-    if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT)
-      DEBUG_ECHOLNPGM("TVAL current (mA) = ", (M91x_counter + 1) * sh.AXIS_STALL_CURRENT_CONSTANT_INV);        // report TVAL current for this run
-    else
-      DEBUG_ECHOLNPGM("kval_hold = ", M91x_counter);                                   // report KVAL_HOLD for this run
-
-    for (j = 0; j < driver_count; j++)
-      L64xxManager.set_param(axis_index[j], L6470_KVAL_HOLD, M91x_counter);  //set KVAL_HOLD or TVAL (same register address)
-
-    M91x_delay_end = millis() + M91x_delay_ms;
-    do {
-      // turn the motor(s) both directions
-      sprintf_P(gcode_string, PSTR("G0 %s%03d F%03d"), temp_axis_string, uint16_t(position_min), uint16_t(final_feedrate));
-      process_subcommands_now(gcode_string);
-
-      sprintf_P(gcode_string, PSTR("G0 %s%03d F%03d"), temp_axis_string, uint16_t(position_max), uint16_t(final_feedrate));
-      process_subcommands_now(gcode_string);
-
-      // get the status after the motors have stopped
-      planner.synchronize();
-
-      status_composite = 0;    // clear out the old bits
-
-      for (j = 0; j < driver_count; j++) {
-        axis_status[j] = (~L64xxManager.get_status(axis_index[j])) & sh.L6470_ERROR_MASK;    // bits of interest are all active low
-        status_composite |= axis_status[j] ;
-      }
-
-      if (status_composite) break;
-    } while (millis() < M91x_delay_end);
-
-    if (status_composite) break;
-
-    M91x_counter++;
-
-  } while (!(status_composite & (sh.STATUS_AXIS_TH_WRN | sh.STATUS_AXIS_TH_SD)) && (M91x_counter < M91x_counter_max));
-
-  DEBUG_ECHOLNPGM(".");
-
-  #if ENABLED(L6470_CHITCHAT)
-    if (status_composite) {
-      L64xxManager.error_status_decode(status_composite, axis_index[0],
-        sh.STATUS_AXIS_TH_SD, sh.STATUS_AXIS_TH_WRN,
-        sh.STATUS_AXIS_STEP_LOSS_A, sh.STATUS_AXIS_STEP_LOSS_B,
-        sh.STATUS_AXIS_OCD, sh.STATUS_AXIS_LAYOUT);
-      DEBUG_ECHOLNPGM(".");
-    }
-  #endif
-
-  if ((status_composite & (sh.STATUS_AXIS_TH_WRN | sh.STATUS_AXIS_TH_SD)))
-    DEBUG_ECHOLNPGM(".\n.\nTest completed normally - Thermal warning/shutdown has occurred");
-  else if (status_composite)
-    DEBUG_ECHOLNPGM(".\n.\nTest completed abnormally - non-thermal error has occurred");
-  else
-    DEBUG_ECHOLNPGM(".\n.\nTest completed normally - Unable to get to thermal warning/shutdown");
-
-  L64xxManager.pause_monitor(false);
-}
-
-/**
- * M917: Find minimum current thresholds
- *
- *   Decrease OCD current until overcurrent error
- *   Increase OCD until overcurrent error goes away
- *   Decrease stall threshold until stall (not done on L6474)
- *   Increase stall until stall error goes away (not done on L6474)
- *
- * J - select which driver(s) to monitor on multi-driver axis
- *     0 - (default) monitor all drivers on the axis or E0
- *     1 - monitor only X, Y, Z, E1
- *     2 - monitor only X2, Y2, Z2, E2
- * Xxxx, Yxxx, Zxxx, Exxx - axis to be monitored with displacement
- *     xxx (1-255) is distance moved on either side of current position
- *
- * F - feedrate
- *     optional - will use default max feedrate from Configuration.h if not specified
- *
- * I - starting over-current threshold
- *     optional - will report current value from driver if not specified
- *     if there are multiple drivers on the axis then all will be set the same
- *
- * T - current (mA) setting for TVAL (0 - 4A in 31.25mA increments, rounds down) - L6474 only
- *     optional - will report current value from driver if not specified
- *
- * K - value for KVAL_HOLD (0 - 255) (ignored for L6474)
- *     optional - will report current value from driver if not specified
- */
-void GcodeSuite::M917() {
-
-  DEBUG_ECHOLNPGM("M917");
-
-  L64xxManager.pause_monitor(true); // Keep monitor_driver() from stealing status
-
-  char axis_mon[3][3] = { {"  "}, {"  "}, {"  "} };   // list of Axes to be monitored
-  L64XX_axis_t axis_index[3];
-  uint16_t axis_status[3];
-  uint8_t driver_count = 1;
-  float position_max;
-  float position_min;
-  float final_feedrate;
-  uint8_t kval_hold;
-  uint8_t OCD_TH_val = 0;
-  uint8_t STALL_TH_val = 0;
-  uint16_t over_current_threshold;
-  constexpr uint8_t over_current_flag = true;
-
-  uint8_t j;   // general purpose counter
-
-  if (L64xxManager.get_user_input(driver_count, axis_index, axis_mon, position_max, position_min, final_feedrate, kval_hold, over_current_flag, OCD_TH_val, STALL_TH_val, over_current_threshold))
-    return;  // quit if invalid user input
-
-  DEBUG_ECHOLNPGM("feedrate = ", final_feedrate);
-
-  planner.synchronize();                             // wait for all current movement commands to complete
-
-  const L64XX_Marlin::L64XX_shadow_t &sh = L64xxManager.shadow;
-  for (j = 0; j < driver_count; j++)
-    L64xxManager.get_status(axis_index[j]);  // clear error flags
-  char temp_axis_string[] = " ";
-  temp_axis_string[0] = axis_mon[0][0];   // need a sprintf format string
-  char gcode_string[80];
-  uint16_t status_composite = 0;
-  uint8_t test_phase = 0;                 // 0 - decreasing OCD - exit when OCD warning occurs (ignore STALL)
-                                          // 1 - increasing OCD - exit when OCD warning stops (ignore STALL)
-                                          // 2 - OCD finalized - decreasing STALL - exit when STALL warning happens
-                                          // 3 - OCD finalized - increasing STALL - exit when STALL warning stop
-                                          // 4 - all testing completed
-  DEBUG_ECHOPGM(".\n.\n.\nover_current threshold : ", (OCD_TH_val + 1) * 375);   // first status display
-  DEBUG_ECHOPGM("  (OCD_TH:  : ", OCD_TH_val);
-  if (sh.STATUS_AXIS_LAYOUT != L6474_STATUS_LAYOUT) {
-    DEBUG_ECHOPGM(")   Stall threshold: ", (STALL_TH_val + 1) * 31.25);
-    DEBUG_ECHOPGM("  (STALL_TH: ", STALL_TH_val);
-  }
-  DEBUG_ECHOLNPGM(")");
-
-  do {
-
-    if (sh.STATUS_AXIS_LAYOUT != L6474_STATUS_LAYOUT) DEBUG_ECHOPGM("STALL threshold : ", (STALL_TH_val + 1) * 31.25);
-    DEBUG_ECHOLNPGM("   OCD threshold : ", (OCD_TH_val + 1) * 375);
-
-    sprintf_P(gcode_string, PSTR("G0 %s%03d F%03d"), temp_axis_string, uint16_t(position_min), uint16_t(final_feedrate));
-    process_subcommands_now(gcode_string);
-
-    sprintf_P(gcode_string, PSTR("G0 %s%03d F%03d"), temp_axis_string, uint16_t(position_max), uint16_t(final_feedrate));
-    process_subcommands_now(gcode_string);
-
-    planner.synchronize();
-
-    status_composite = 0;    // clear out the old bits
-
-    for (j = 0; j < driver_count; j++) {
-      axis_status[j] = (~L64xxManager.get_status(axis_index[j])) & sh.L6470_ERROR_MASK;    // bits of interest are all active low
-      status_composite |= axis_status[j];
-    }
-
-    if (status_composite && (status_composite & sh.STATUS_AXIS_UVLO)) {
-      DEBUG_ECHOLNPGM("Test aborted (Undervoltage lockout active)");
-      #if ENABLED(L6470_CHITCHAT)
-        for (j = 0; j < driver_count; j++) {
-          if (j) DEBUG_ECHOPGM("...");
-          L64xxManager.error_status_decode(axis_status[j], axis_index[j],
-            sh.STATUS_AXIS_TH_SD, sh.STATUS_AXIS_TH_WRN,
-            sh.STATUS_AXIS_STEP_LOSS_A, sh.STATUS_AXIS_STEP_LOSS_B,
-            sh.STATUS_AXIS_OCD, sh.STATUS_AXIS_LAYOUT);
-        }
-      #endif
-      return;
-    }
-
-    if (status_composite & (sh.STATUS_AXIS_TH_WRN | sh.STATUS_AXIS_TH_SD)) {
-      DEBUG_ECHOLNPGM("thermal problem - waiting for chip(s) to cool down ");
-      uint16_t status_composite_temp = 0;
-      uint8_t k = 0;
-      do {
-        k++;
-        if (!(k % 4)) {
-          kval_hold *= 0.95;
-          DEBUG_EOL();
-          DEBUG_ECHOLNPGM("Lowering KVAL_HOLD by about 5% to ", kval_hold);
-          for (j = 0; j < driver_count; j++)
-            L64xxManager.set_param(axis_index[j], L6470_KVAL_HOLD, kval_hold);
-        }
-        DEBUG_ECHOLNPGM(".");
-        reset_stepper_timeout(); // keep steppers powered
-        safe_delay(5000);
-        status_composite_temp = 0;
-        for (j = 0; j < driver_count; j++) {
-          axis_status[j] = (~L64xxManager.get_status(axis_index[j])) & sh.L6470_ERROR_MASK;    // bits of interest are all active low
-          status_composite_temp |= axis_status[j];
-        }
-      }
-      while (status_composite_temp & (sh.STATUS_AXIS_TH_WRN | sh.STATUS_AXIS_TH_SD));
-      DEBUG_EOL();
-    }
-    if (status_composite & (sh.STATUS_AXIS_STEP_LOSS_A | sh.STATUS_AXIS_STEP_LOSS_B | sh.STATUS_AXIS_OCD)) {
-      switch (test_phase) {
-
-        case 0: {
-          if (status_composite & sh.STATUS_AXIS_OCD) {
-            // phase 0 with OCD warning - time to go to next phase
-            if (OCD_TH_val >= sh.AXIS_OCD_TH_MAX) {
-              OCD_TH_val = sh.AXIS_OCD_TH_MAX;           // limit to max
-              test_phase = 2;            // at highest value so skip phase 1
-              //DEBUG_ECHOLNPGM("LOGIC E0A OCD at highest - skip to 2");
-              DEBUG_ECHOLNPGM("OCD at highest - OCD finalized");
-            }
-            else {
-              OCD_TH_val++;              // normal exit to next phase
-              test_phase = 1;            // setup for first pass of phase 1
-              //DEBUG_ECHOLNPGM("LOGIC E0B - inc OCD  & go to 1");
-              DEBUG_ECHOLNPGM("inc OCD");
-            }
-          }
-          else {  // phase 0 without OCD warning - keep on decrementing if can
-            if (OCD_TH_val) {
-              OCD_TH_val--;              // try lower value
-              //DEBUG_ECHOLNPGM("LOGIC E0C - dec OCD");
-              DEBUG_ECHOLNPGM("dec OCD");
-            }
-            else {
-              test_phase = 2;            // at lowest value without warning so skip phase 1
-              //DEBUG_ECHOLNPGM("LOGIC E0D - OCD at latest - go to 2");
-              DEBUG_ECHOLNPGM("OCD finalized");
-            }
-          }
-        } break;
-
-        case 1: {
-          if (status_composite & sh.STATUS_AXIS_OCD) {
-            // phase 1 with OCD warning - increment if can
-            if (OCD_TH_val >= sh.AXIS_OCD_TH_MAX) {
-              OCD_TH_val = sh.AXIS_OCD_TH_MAX;           // limit to max
-              test_phase = 2;            // at highest value so go to next phase
-              //DEBUG_ECHOLNPGM("LOGIC E1A - OCD at max - go to 2");
-              DEBUG_ECHOLNPGM("OCD finalized");
-            }
-            else {
-              OCD_TH_val++;              // try a higher value
-              //DEBUG_ECHOLNPGM("LOGIC E1B - inc OCD");
-              DEBUG_ECHOLNPGM("inc OCD");
-            }
-          }
-          else { // phase 1 without OCD warning - normal exit to phase 2
-            test_phase = 2;
-            //DEBUG_ECHOLNPGM("LOGIC E1C - no OCD warning - go to 1");
-            DEBUG_ECHOLNPGM("OCD finalized");
-          }
-        } break;
-
-        case 2: {
-          if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT) {  // skip all STALL_TH steps if L6474
-            test_phase = 4;
-            break;
-          }
-          if (status_composite & (sh.STATUS_AXIS_STEP_LOSS_A | sh.STATUS_AXIS_STEP_LOSS_B)) {
-            // phase 2 with stall warning - time to go to next phase
-            if (STALL_TH_val >= 127) {
-              STALL_TH_val = 127;  // limit to max
-              //DEBUG_ECHOLNPGM("LOGIC E2A - STALL warning, STALL at max, quit");
-              DEBUG_ECHOLNPGM("finished - STALL at maximum value but still have stall warning");
-              test_phase = 4;
-            }
-            else {
-              test_phase = 3;              // normal exit to next phase (found failing value of STALL)
-              STALL_TH_val++;              // setup for first pass of phase 3
-              //DEBUG_ECHOLNPGM("LOGIC E2B - INC - STALL warning, inc Stall, go to 3");
-              DEBUG_ECHOLNPGM("inc Stall");
-            }
-          }
-          else {  // phase 2 without stall warning - decrement if can
-            if (STALL_TH_val) {
-              STALL_TH_val--;              // try a lower value
-              //DEBUG_ECHOLNPGM("LOGIC E2C - no STALL, dec STALL");
-              DEBUG_ECHOLNPGM("dec STALL");
-            }
-            else {
-              DEBUG_ECHOLNPGM("finished - STALL at lowest value but still do NOT have stall warning");
-              test_phase = 4;
-              //DEBUG_ECHOLNPGM("LOGIC E2D - no STALL, at lowest so quit");
-            }
-          }
-        } break;
-
-        case 3: {
-          if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT) {  // skip all STALL_TH steps if L6474
-            test_phase = 4;
-            break;
-          }
-          if (status_composite & (sh.STATUS_AXIS_STEP_LOSS_A | sh.STATUS_AXIS_STEP_LOSS_B)) {
-            // phase 3 with stall warning - increment if can
-            if (STALL_TH_val >= 127) {
-              STALL_TH_val = 127; // limit to max
-              DEBUG_ECHOLNPGM("finished - STALL at maximum value but still have stall warning");
-              test_phase = 4;
-              //DEBUG_ECHOLNPGM("LOGIC E3A - STALL, at max so quit");
-            }
-            else {
-              STALL_TH_val++;              // still looking for passing value
-              //DEBUG_ECHOLNPGM("LOGIC E3B - STALL, inc stall");
-              DEBUG_ECHOLNPGM("inc stall");
-            }
-          }
-          else {  //phase 3 without stall warning  but have OCD warning
-            DEBUG_ECHOLNPGM("Hardware problem - OCD warning without STALL warning");
-            test_phase = 4;
-            //DEBUG_ECHOLNPGM("LOGIC E3C - not STALLED, hardware problem (quit)");
-          }
-        } break;
-
-      }
-
-    }
-    else {
-      switch (test_phase) {
-        case 0: { // phase 0 without OCD warning - keep on decrementing if can
-          if (OCD_TH_val) {
-            OCD_TH_val--;             // try lower value
-            //DEBUG_ECHOLNPGM("LOGIC N0A - DEC OCD");
-            DEBUG_ECHOLNPGM("DEC OCD");
-          }
-          else {
-            test_phase = 2;           // at lowest value without warning so skip phase 1
-            //DEBUG_ECHOLNPGM("LOGIC N0B - OCD at lowest (go to phase 2)");
-            DEBUG_ECHOLNPGM("OCD finalized");
-          }
-        } break;
-
-        case 1: //DEBUG_ECHOLNPGM("LOGIC N1 (go directly to 2)"); // phase 1 without OCD warning - drop directly to phase 2
-                DEBUG_ECHOLNPGM("OCD finalized");
-
-        case 2: { // phase 2 without stall warning - keep on decrementing if can
-          if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT) {  // skip all STALL_TH steps if L6474
-            test_phase = 4;
-            break;
-          }
-          if (STALL_TH_val) {
-            STALL_TH_val--;              // try a lower value (stay in phase 2)
-            //DEBUG_ECHOLNPGM("LOGIC N2B - dec STALL");
-            DEBUG_ECHOLNPGM("dec STALL");
-          }
-          else {
-            DEBUG_ECHOLNPGM("finished - STALL at lowest value but still no stall warning");
-            test_phase = 4;
-            //DEBUG_ECHOLNPGM("LOGIC N2C - STALL at lowest (quit)");
-          }
-        } break;
-
-        case 3: {
-          if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT) {  // skip all STALL_TH steps if L6474
-            test_phase = 4;
-            break;
-          }
-          test_phase = 4;
-           //DEBUG_ECHOLNPGM("LOGIC N3 - finished!");
-           DEBUG_ECHOLNPGM("finished!");
-        } break;  // phase 3 without any warnings - desired exit
-      }  //
-    }  // end of status checks
-
-    if (test_phase != 4) {
-      for (j = 0; j < driver_count; j++) {                       // update threshold(s)
-        L64xxManager.set_param(axis_index[j], L6470_OCD_TH, OCD_TH_val);
-        if (sh.STATUS_AXIS_LAYOUT != L6474_STATUS_LAYOUT) L64xxManager.set_param(axis_index[j], L6470_STALL_TH, STALL_TH_val);
-        if (L64xxManager.get_param(axis_index[j], L6470_OCD_TH) != OCD_TH_val) DEBUG_ECHOLNPGM("OCD mismatch");
-        if ((L64xxManager.get_param(axis_index[j], L6470_STALL_TH) != STALL_TH_val) && (sh.STATUS_AXIS_LAYOUT != L6474_STATUS_LAYOUT)) DEBUG_ECHOLNPGM("STALL mismatch");
-      }
-    }
-
-  } while (test_phase != 4);
-
-  DEBUG_ECHOLNPGM(".");
-  if (status_composite) {
-    #if ENABLED(L6470_CHITCHAT)
-      for (j = 0; j < driver_count; j++) {
-        if (j) DEBUG_ECHOPGM("...");
-        L64xxManager.error_status_decode(axis_status[j], axis_index[j],
-          sh.STATUS_AXIS_TH_SD, sh.STATUS_AXIS_TH_WRN,
-          sh.STATUS_AXIS_STEP_LOSS_A, sh.STATUS_AXIS_STEP_LOSS_B,
-          sh.STATUS_AXIS_OCD, sh.STATUS_AXIS_LAYOUT);
-      }
-      DEBUG_ECHOLNPGM(".");
-    #endif
-    DEBUG_ECHOLNPGM("Completed with errors");
-  }
-  else
-    DEBUG_ECHOLNPGM("Completed with no errors");
-  DEBUG_ECHOLNPGM(".");
-
-  L64xxManager.pause_monitor(false);
-}
-
-/**
- * M918: increase speed until error or max feedrate achieved (as shown in configuration.h))
- *
- * J - select which driver(s) to monitor on multi-driver axis
- *     0 - (default) monitor all drivers on the axis or E0
- *     1 - monitor only X, Y, Z, E1
- *     2 - monitor only X2, Y2, Z2, E2
- * Xxxx, Yxxx, Zxxx, Exxx - axis to be monitored with displacement
- *     xxx (1-255) is distance moved on either side of current position
- *
- * I - over current threshold
- *     optional - will report current value from driver if not specified
- *
- * T - current (mA) setting for TVAL (0 - 4A in 31.25mA increments, rounds down) - L6474 only
- *     optional - will report current value from driver if not specified
- *
- * K - value for KVAL_HOLD (0 - 255) (ignored for L6474)
- *     optional - will report current value from driver if not specified
- *
- * M - value for microsteps (1 - 128) (optional)
- *     optional - will report current value from driver if not specified
- */
-void GcodeSuite::M918() {
-
-  DEBUG_ECHOLNPGM("M918");
-
-  L64xxManager.pause_monitor(true); // Keep monitor_driver() from stealing status
-
-  char axis_mon[3][3] = { {"  "}, {"  "}, {"  "} };   // list of Axes to be monitored
-  L64XX_axis_t axis_index[3];
-  uint16_t axis_status[3];
-  uint8_t driver_count = 1;
-  float position_max, position_min;
-  float final_feedrate;
-  uint8_t kval_hold;
-  uint8_t OCD_TH_val = 0;
-  uint8_t STALL_TH_val = 0;
-  uint16_t over_current_threshold;
-  constexpr uint8_t over_current_flag = true;
-
-  const L64XX_Marlin::L64XX_shadow_t &sh = L64xxManager.shadow;
-
-  uint8_t j;   // general purpose counter
-
-  if (L64xxManager.get_user_input(driver_count, axis_index, axis_mon, position_max, position_min, final_feedrate, kval_hold, over_current_flag, OCD_TH_val, STALL_TH_val, over_current_threshold))
-    return;  // quit if invalid user input
-
-  L64xxManager.get_status(axis_index[0]); // populate shadow array
-
-  uint8_t m_steps = parser.byteval('M');
-
-  if (m_steps != 0) {
-    LIMIT(m_steps, 1, sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT ? 16 : 128);  // L6474
-
-    uint8_t stepVal;
-    for (stepVal = 0; stepVal < 8; stepVal++) {  // convert to L64xx register value
-      if (m_steps == 1) break;
-      m_steps >>= 1;
-    }
-
-    if (sh.STATUS_AXIS_LAYOUT == L6474_STATUS_LAYOUT)
-      stepVal |= 0x98;  // NO SYNC
-    else
-      stepVal |= (!SYNC_EN) | SYNC_SEL_1 | stepVal;
-
-    for (j = 0; j < driver_count; j++) {
-      L64xxManager.set_param(axis_index[j], dSPIN_HARD_HIZ, 0);          // can't write STEP register if stepper being powered
-                                                                         //   results in an extra NOOP being sent (data 00)
-      L64xxManager.set_param(axis_index[j], L6470_STEP_MODE, stepVal);   // set microsteps
-    }
-  }
-  m_steps = L64xxManager.get_param(axis_index[0], L6470_STEP_MODE) & 0x07;   // get microsteps
-
-  DEBUG_ECHOLNPGM("Microsteps = ", _BV(m_steps));
-  DEBUG_ECHOLNPGM("target (maximum) feedrate = ", final_feedrate);
-
-  const float feedrate_inc = final_feedrate / 10,   // Start at 1/10 of max & go up by 1/10 per step
-              fr_limit = final_feedrate * 0.99f;    // Rounding-safe comparison value
-  float current_feedrate = 0;
-
-  planner.synchronize();                            // Wait for moves to complete
-
-  for (j = 0; j < driver_count; j++)
-    L64xxManager.get_status(axis_index[j]);         // Clear error flags
-
-  char temp_axis_string[2] = " ";
-  temp_axis_string[0] = axis_mon[0][0];             // Need a sprintf format string
-  //temp_axis_string[1] = '\n';
-
-  char gcode_string[80];
-  uint16_t status_composite = 0;
-  DEBUG_ECHOLNPGM(".\n.\n.");                       // Make feedrate outputs easier to read
-
-  do {
-    current_feedrate += feedrate_inc;
-    DEBUG_ECHOLNPGM("...feedrate = ", current_feedrate);
-
-    sprintf_P(gcode_string, PSTR("G0 %s%03d F%03d"), temp_axis_string, uint16_t(position_min), uint16_t(current_feedrate));
-    process_subcommands_now(gcode_string);
-
-    sprintf_P(gcode_string, PSTR("G0 %s%03d F%03d"), temp_axis_string, uint16_t(position_max), uint16_t(current_feedrate));
-    process_subcommands_now(gcode_string);
-
-    planner.synchronize();
-
-    for (j = 0; j < driver_count; j++) {
-      axis_status[j] = (~L64xxManager.get_status(axis_index[j])) & 0x0800;  // Bits of interest are all active LOW
-      status_composite |= axis_status[j];
-    }
-    if (status_composite) break;              // Break on any error
-  } while (current_feedrate < fr_limit);
-
-  DEBUG_ECHOPGM("Completed with ");
-  if (status_composite) {
-    DEBUG_ECHOLNPGM("errors");
-    #if ENABLED(L6470_CHITCHAT)
-      for (j = 0; j < driver_count; j++) {
-        if (j) DEBUG_ECHOPGM("...");
-        L64xxManager.error_status_decode(axis_status[j], axis_index[j],
-          sh.STATUS_AXIS_TH_SD, sh.STATUS_AXIS_TH_WRN,
-          sh.STATUS_AXIS_STEP_LOSS_A, sh.STATUS_AXIS_STEP_LOSS_B,
-          sh.STATUS_AXIS_OCD, sh.STATUS_AXIS_LAYOUT);
-      }
-    #endif
-  }
-  else
-    DEBUG_ECHOLNPGM("no errors");
-
-  L64xxManager.pause_monitor(false);
-}
-
-#endif // HAS_L64XX

Marlin/src/gcode/gcode.cpp

@@ -1005,14 +1005,6 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
         case 919: M919(); break;                                  // M919: Set stepper Chopper Times
       #endif
 
-      #if HAS_L64XX
-        case 122: M122(); break;                                   // M122: Report status
-        case 906: M906(); break;                                   // M906: Set or get motor drive level
-        case 916: M916(); break;                                   // M916: L6470 tuning: Increase drive level until thermal warning
-        case 917: M917(); break;                                   // M917: L6470 tuning: Find minimum current thresholds
-        case 918: M918(); break;                                   // M918: L6470 tuning: Increase speed until max or error
-      #endif
-
       #if HAS_MICROSTEPS
         case 350: M350(); break;                                  // M350: Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers.
         case 351: M351(); break;                                  // M351: Toggle MS1 MS2 pins directly, S# determines MS1 or MS2, X# sets the pin high/low.

Marlin/src/gcode/gcode.h

@@ -155,7 +155,7 @@
  * M120 - Enable endstops detection.
  * M121 - Disable endstops detection.
  *
- * M122 - Debug stepper (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470)
+ * M122 - Debug stepper (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660)
  * M123 - Report fan tachometers. (Requires En_FAN_TACHO_PIN) Optionally set auto-report interval. (Requires AUTO_REPORT_FANS)
  * M125 - Save current position and move to filament change position. (Requires PARK_HEAD_ON_PAUSE)
  *
@@ -286,7 +286,7 @@
  * M871 - Print/reset/clear first layer temperature offset values. (Requires PTC_PROBE, PTC_BED, or PTC_HOTEND)
  * M876 - Handle Prompt Response. (Requires HOST_PROMPT_SUPPORT and not EMERGENCY_PARSER)
  * M900 - Get or Set Linear Advance K-factor. (Requires LIN_ADVANCE)
- * M906 - Set or get motor current in milliamps using axis codes XYZE, etc. Report values if no axis codes given. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470)
+ * M906 - Set or get motor current in milliamps using axis codes XYZE, etc. Report values if no axis codes given. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660)
  * M907 - Set digital trimpot motor current using axis codes. (Requires a board with digital trimpots)
  * M908 - Control digital trimpot directly. (Requires HAS_MOTOR_CURRENT_DAC or DIGIPOTSS_PIN)
  * M909 - Print digipot/DAC current value. (Requires HAS_MOTOR_CURRENT_DAC)
@@ -295,9 +295,6 @@
  * M912 - Clear stepper driver overtemperature pre-warn condition flag. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660)
  * M913 - Set HYBRID_THRESHOLD speed. (Requires HYBRID_THRESHOLD)
  * M914 - Set StallGuard sensitivity. (Requires SENSORLESS_HOMING or SENSORLESS_PROBING)
- * M916 - L6470 tuning: Increase KVAL_HOLD until thermal warning. (Requires at least one _DRIVER_TYPE L6470)
- * M917 - L6470 tuning: Find minimum current thresholds. (Requires at least one _DRIVER_TYPE L6470)
- * M918 - L6470 tuning: Increase speed until max or error. (Requires at least one _DRIVER_TYPE L6470)
  * M919 - Get or Set motor Chopper Times (time_off, hysteresis_end, hysteresis_start) using axis codes XYZE, etc. If no parameters are given, report. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660)
  * M951 - Set Magnetic Parking Extruder parameters. (Requires MAGNETIC_PARKING_EXTRUDER)
  * M3426 - Read MCP3426 ADC over I2C. (Requires HAS_MCP3426_ADC)
@@ -1163,14 +1160,6 @@ private:
     static void M919();
   #endif
 
-  #if HAS_L64XX
-    static void M122();
-    static void M906();
-    static void M916();
-    static void M917();
-    static void M918();
-  #endif
-
   #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM || HAS_MOTOR_CURRENT_I2C || HAS_MOTOR_CURRENT_DAC
     static void M907();
     #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM

Marlin/src/gcode/host/M114.cpp

@@ -28,12 +28,6 @@
 
 #if ENABLED(M114_DETAIL)
 
-  #if HAS_L64XX
-    #include "../../libs/L64XX/L64XX_Marlin.h"
-    #define DEBUG_OUT ENABLED(L6470_CHITCHAT)
-    #include "../../core/debug_out.h"
-  #endif
-
   void report_all_axis_pos(const xyze_pos_t &pos, const uint8_t n=LOGICAL_AXES, const uint8_t precision=3) {
     char str[12];
     LOOP_L_N(a, n) {
@@ -84,89 +78,6 @@
 
     planner.synchronize();
 
-    #if HAS_L64XX
-      char temp_buf[80];
-      int32_t temp;
-      //#define ABS_POS_SIGN_MASK 0b1111 1111 1110 0000 0000 0000 0000 0000
-      #define ABS_POS_SIGN_MASK 0b11111111111000000000000000000000
-      #define REPORT_ABSOLUTE_POS(Q) do{                            \
-          L64xxManager.say_axis(Q, false);                          \
-          temp = L6470_GETPARAM(L6470_ABS_POS,Q);                   \
-          if (temp & ABS_POS_SIGN_MASK) temp |= ABS_POS_SIGN_MASK;  \
-          sprintf_P(temp_buf, PSTR(":%8ld   "), temp);              \
-          DEBUG_ECHO(temp_buf);                                     \
-        }while(0)
-
-      DEBUG_ECHOPGM("\nL6470:");
-      #if AXIS_IS_L64XX(X)
-        REPORT_ABSOLUTE_POS(X);
-      #endif
-      #if AXIS_IS_L64XX(X2)
-        REPORT_ABSOLUTE_POS(X2);
-      #endif
-      #if AXIS_IS_L64XX(Y)
-        REPORT_ABSOLUTE_POS(Y);
-      #endif
-      #if AXIS_IS_L64XX(Y2)
-        REPORT_ABSOLUTE_POS(Y2);
-      #endif
-      #if AXIS_IS_L64XX(Z)
-        REPORT_ABSOLUTE_POS(Z);
-      #endif
-      #if AXIS_IS_L64XX(Z2)
-        REPORT_ABSOLUTE_POS(Z2);
-      #endif
-      #if AXIS_IS_L64XX(Z3)
-        REPORT_ABSOLUTE_POS(Z3);
-      #endif
-      #if AXIS_IS_L64XX(Z4)
-        REPORT_ABSOLUTE_POS(Z4);
-      #endif
-      #if AXIS_IS_L64XX(I)
-        REPORT_ABSOLUTE_POS(I);
-      #endif
-      #if AXIS_IS_L64XX(J)
-        REPORT_ABSOLUTE_POS(J);
-      #endif
-      #if AXIS_IS_L64XX(K)
-        REPORT_ABSOLUTE_POS(K);
-      #endif
-      #if AXIS_IS_L64XX(U)
-        REPORT_ABSOLUTE_POS(U);
-      #endif
-      #if AXIS_IS_L64XX(V)
-        REPORT_ABSOLUTE_POS(V);
-      #endif
-      #if AXIS_IS_L64XX(W)
-        REPORT_ABSOLUTE_POS(W);
-      #endif
-      #if AXIS_IS_L64XX(E0)
-        REPORT_ABSOLUTE_POS(E0);
-      #endif
-      #if AXIS_IS_L64XX(E1)
-        REPORT_ABSOLUTE_POS(E1);
-      #endif
-      #if AXIS_IS_L64XX(E2)
-        REPORT_ABSOLUTE_POS(E2);
-      #endif
-      #if AXIS_IS_L64XX(E3)
-        REPORT_ABSOLUTE_POS(E3);
-      #endif
-      #if AXIS_IS_L64XX(E4)
-        REPORT_ABSOLUTE_POS(E4);
-      #endif
-      #if AXIS_IS_L64XX(E5)
-        REPORT_ABSOLUTE_POS(E5);
-      #endif
-      #if AXIS_IS_L64XX(E6)
-        REPORT_ABSOLUTE_POS(E6);
-      #endif
-      #if AXIS_IS_L64XX(E7)
-        REPORT_ABSOLUTE_POS(E7);
-      #endif
-      SERIAL_EOL();
-    #endif // HAS_L64XX
-
     SERIAL_ECHOPGM("Stepper:");
     LOOP_LOGICAL_AXES(i) {
       SERIAL_ECHOPGM_P((PGM_P)pgm_read_ptr(&SP_AXIS_LBL[i]), stepper.position((AxisEnum)i));

Marlin/src/inc/Conditionals_post.h

@@ -1610,7 +1610,7 @@
   #define HAS_X_MS_PINS 1
 #endif
 
-#if PIN_EXISTS(X2_ENABLE) || AXIS_IS_L64XX(X2) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(X2))
+#if PIN_EXISTS(X2_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(X2))
   #define HAS_X2_ENABLE 1
 #endif
 #if PIN_EXISTS(X2_DIR)
@@ -1631,7 +1631,7 @@
 #endif
 
 #if HAS_Y_AXIS
-  #if PIN_EXISTS(Y_ENABLE) || AXIS_IS_L64XX(Y) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Y))
+  #if PIN_EXISTS(Y_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Y))
     #define HAS_Y_ENABLE 1
   #endif
   #if PIN_EXISTS(Y_DIR)
@@ -1644,7 +1644,7 @@
     #define HAS_Y_MS_PINS 1
   #endif
 
-  #if PIN_EXISTS(Y2_ENABLE) || AXIS_IS_L64XX(Y2) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Y2))
+  #if PIN_EXISTS(Y2_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Y2))
     #define HAS_Y2_ENABLE 1
   #endif
   #if PIN_EXISTS(Y2_DIR)
@@ -1664,7 +1664,7 @@
 #endif
 
 #if HAS_Z_AXIS
-  #if PIN_EXISTS(Z_ENABLE) || AXIS_IS_L64XX(Z) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z))
+  #if PIN_EXISTS(Z_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z))
     #define HAS_Z_ENABLE 1
   #endif
   #if PIN_EXISTS(Z_DIR)
@@ -1684,7 +1684,7 @@
 #endif
 
 #if NUM_Z_STEPPERS >= 2
-  #if PIN_EXISTS(Z2_ENABLE) || AXIS_IS_L64XX(Z2) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z2))
+  #if PIN_EXISTS(Z2_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z2))
     #define HAS_Z2_ENABLE 1
   #endif
   #if PIN_EXISTS(Z2_DIR)
@@ -1699,7 +1699,7 @@
 #endif
 
 #if NUM_Z_STEPPERS >= 3
-  #if PIN_EXISTS(Z3_ENABLE) || AXIS_IS_L64XX(Z3) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z3))
+  #if PIN_EXISTS(Z3_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z3))
     #define HAS_Z3_ENABLE 1
   #endif
   #if PIN_EXISTS(Z3_DIR)
@@ -1714,7 +1714,7 @@
 #endif
 
 #if NUM_Z_STEPPERS >= 4
-  #if PIN_EXISTS(Z4_ENABLE) || AXIS_IS_L64XX(Z4) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z4))
+  #if PIN_EXISTS(Z4_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(Z4))
     #define HAS_Z4_ENABLE 1
   #endif
   #if PIN_EXISTS(Z4_DIR)
@@ -1729,7 +1729,7 @@
 #endif
 
 #if HAS_I_AXIS
-  #if PIN_EXISTS(I_ENABLE) || AXIS_IS_L64XX(I) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(I))
+  #if PIN_EXISTS(I_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(I))
     #define HAS_I_ENABLE 1
   #endif
   #if PIN_EXISTS(I_DIR)
@@ -1749,7 +1749,7 @@
 #endif
 
 #if HAS_J_AXIS
-  #if PIN_EXISTS(J_ENABLE) || AXIS_IS_L64XX(J) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(J))
+  #if PIN_EXISTS(J_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(J))
     #define HAS_J_ENABLE 1
   #endif
   #if PIN_EXISTS(J_DIR)
@@ -1769,7 +1769,7 @@
 #endif
 
 #if HAS_K_AXIS
-  #if PIN_EXISTS(K_ENABLE) || AXIS_IS_L64XX(K) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(K))
+  #if PIN_EXISTS(K_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(K))
     #define HAS_K_ENABLE 1
   #endif
   #if PIN_EXISTS(K_DIR)
@@ -1789,7 +1789,7 @@
 #endif
 
 #if HAS_U_AXIS
-  #if PIN_EXISTS(U_ENABLE) || AXIS_IS_L64XX(U) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(U))
+  #if PIN_EXISTS(U_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(U))
     #define HAS_U_ENABLE 1
   #endif
   #if PIN_EXISTS(U_DIR)
@@ -1809,7 +1809,7 @@
 #endif
 
 #if HAS_V_AXIS
-  #if PIN_EXISTS(V_ENABLE) || AXIS_IS_L64XX(V) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(V))
+  #if PIN_EXISTS(V_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(V))
     #define HAS_V_ENABLE 1
   #endif
   #if PIN_EXISTS(V_DIR)
@@ -1829,7 +1829,7 @@
 #endif
 
 #if HAS_W_AXIS
-  #if PIN_EXISTS(W_ENABLE) || AXIS_IS_L64XX(W) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(W))
+  #if PIN_EXISTS(W_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(W))
     #define HAS_W_ENABLE 1
   #endif
   #if PIN_EXISTS(W_DIR)
@@ -1851,7 +1851,7 @@
 // Extruder steppers and solenoids
 #if HAS_EXTRUDERS
 
-  #if PIN_EXISTS(E0_ENABLE) || AXIS_IS_L64XX(E0) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E0))
+  #if PIN_EXISTS(E0_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E0))
     #define HAS_E0_ENABLE 1
   #endif
   #if PIN_EXISTS(E0_DIR)
@@ -1865,7 +1865,7 @@
   #endif
 
   #if E_STEPPERS > 1 || ENABLED(E_DUAL_STEPPER_DRIVERS)
-    #if PIN_EXISTS(E1_ENABLE) || AXIS_IS_L64XX(E1) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E1))
+    #if PIN_EXISTS(E1_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E1))
       #define HAS_E1_ENABLE 1
     #endif
     #if PIN_EXISTS(E1_DIR)
@@ -1880,7 +1880,7 @@
   #endif
 
   #if E_STEPPERS > 2
-    #if PIN_EXISTS(E2_ENABLE) || AXIS_IS_L64XX(E2) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E2))
+    #if PIN_EXISTS(E2_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E2))
       #define HAS_E2_ENABLE 1
     #endif
     #if PIN_EXISTS(E2_DIR)
@@ -1895,7 +1895,7 @@
   #endif
 
   #if E_STEPPERS > 3
-    #if PIN_EXISTS(E3_ENABLE) || AXIS_IS_L64XX(E3) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E3))
+    #if PIN_EXISTS(E3_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E3))
       #define HAS_E3_ENABLE 1
     #endif
     #if PIN_EXISTS(E3_DIR)
@@ -1910,7 +1910,7 @@
   #endif
 
   #if E_STEPPERS > 4
-    #if PIN_EXISTS(E4_ENABLE) || AXIS_IS_L64XX(E4) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E4))
+    #if PIN_EXISTS(E4_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E4))
       #define HAS_E4_ENABLE 1
     #endif
     #if PIN_EXISTS(E4_DIR)
@@ -1925,7 +1925,7 @@
   #endif
 
   #if E_STEPPERS > 5
-    #if PIN_EXISTS(E5_ENABLE) || AXIS_IS_L64XX(E5) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E5))
+    #if PIN_EXISTS(E5_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E5))
       #define HAS_E5_ENABLE 1
     #endif
     #if PIN_EXISTS(E5_DIR)
@@ -1940,7 +1940,7 @@
   #endif
 
   #if E_STEPPERS > 6
-    #if PIN_EXISTS(E6_ENABLE) || AXIS_IS_L64XX(E6) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E6))
+    #if PIN_EXISTS(E6_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E6))
       #define HAS_E6_ENABLE 1
     #endif
     #if PIN_EXISTS(E6_DIR)
@@ -1955,7 +1955,7 @@
   #endif
 
   #if E_STEPPERS > 7
-    #if PIN_EXISTS(E7_ENABLE) || AXIS_IS_L64XX(E7) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E7))
+    #if PIN_EXISTS(E7_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E7))
       #define HAS_E7_ENABLE 1
     #endif
     #if PIN_EXISTS(E7_DIR)

Marlin/src/inc/SanityCheck.h

@@ -350,7 +350,7 @@
 #elif defined(HAVE_TMC2208)
   #error "HAVE_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208."
 #elif defined(HAVE_L6470DRIVER)
-  #error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470."
+  #error "HAVE_L6470DRIVER is obsolete. L64xx stepper drivers are no longer supported in Marlin."
 #elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \
    || defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) || defined(E5_IS_TMC) || defined(E6_IS_TMC) || defined(E7_IS_TMC)
   #error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X."
@@ -363,9 +363,6 @@
 #elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \
    || defined(E0_IS_TMC2208) || defined(E1_IS_TMC2208) || defined(E2_IS_TMC2208) || defined(E3_IS_TMC2208) || defined(E4_IS_TMC2208) || defined(E5_IS_TMC2208) || defined(E6_IS_TMC2208) || defined(E7_IS_TMC2208)
   #error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208."
-#elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \
-   || defined(E0_IS_L6470) || defined(E1_IS_L6470) || defined(E2_IS_L6470) || defined(E3_IS_L6470) || defined(E4_IS_L6470) || defined(E5_IS_L6470) || defined(E6_IS_L6470) || defined(E7_IS_L6470)
-  #error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470."
 #elif defined(AUTOMATIC_CURRENT_CONTROL)
   #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS."
 #elif defined(FILAMENT_CHANGE_LOAD_LENGTH)
@@ -647,6 +644,26 @@
   #error "LEVEL_CENTER_TOO is now BED_TRAMMING_INCLUDE_CENTER."
 #endif
 
+// L64xx stepper drivers have been removed
+#define _L6470              0x6470
+#define _L6474              0x6474
+#define _L6480              0x6480
+#define _POWERSTEP01        0xF00D
+#if HAS_DRIVER(L6470)
+  #error "L6470 stepper drivers are no longer supported in Marlin."
+#elif HAS_DRIVER(L6474)
+  #error "L6474 stepper drivers are no longer supported in Marlin."
+#elif HAS_DRIVER(L6480)
+  #error "L6480 stepper drivers are no longer supported in Marlin."
+#elif HAS_DRIVER(POWERSTEP01)
+  #error "POWERSTEP01 stepper drivers are no longer supported in Marlin."
+#endif
+#undef _L6470
+#undef _L6474
+#undef _L6480
+#undef _POWERSTEP01
+
+// Check AXIS_RELATIVE_MODES
 constexpr float arm[] = AXIS_RELATIVE_MODES;
 static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _LOGICAL_AXES_STR "elements.");
 
@@ -3533,7 +3550,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * TMC SPI Chaining
  */
-#define IN_CHAIN(A) ((A##_CHAIN_POS > 0) && !HAS_L64XX)
+#define IN_CHAIN(A) A##_CHAIN_POS > 0
 #if  IN_CHAIN(X ) || IN_CHAIN(Y ) || IN_CHAIN(Z ) || IN_CHAIN(X2) || IN_CHAIN(Y2) || IN_CHAIN(Z2) || IN_CHAIN(Z3) || IN_CHAIN(Z4) \
   || IN_CHAIN(E0) || IN_CHAIN(E1) || IN_CHAIN(E2) || IN_CHAIN(E3) || IN_CHAIN(E4) || IN_CHAIN(E5) || IN_CHAIN(E6) || IN_CHAIN(E7)
   #define BAD_CHAIN(A) (IN_CHAIN(A) && !PIN_EXISTS(A##_CS))
@@ -3599,13 +3616,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 #undef IN_CHAIN
 
 /**
- * L64XX requirement
- */
-#if HAS_L64XX && NUM_AXES > 3
-  #error "L64XX requires NUM_AXES <= 3. Homing with L64XX is not yet implemented for NUM_AXES > 3."
-#endif
-
-/**
  * Digipot requirement
  */
 #if HAS_MOTOR_CURRENT_I2C

Marlin/src/libs/L64XX/L64XX_Marlin.h

@@ -1,141 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#include "../../inc/MarlinConfig.h"
-
-#include <L6470.h>
-#if !(L6470_LIBRARY_VERSION >= 0x000800)
-  #error 'L6470_LIBRARY_VERSION 0x000800 or later required'
-#endif
-
-#define L6470_GETPARAM(P,Q) stepper##Q.GetParam(P)
-
-#define dSPIN_STEP_CLOCK      0x58
-#define dSPIN_STEP_CLOCK_FWD dSPIN_STEP_CLOCK
-#define dSPIN_STEP_CLOCK_REV dSPIN_STEP_CLOCK+1
-#define HAS_L64XX_EXTRUDER (AXIS_IS_L64XX(E0) || AXIS_IS_L64XX(E1) || AXIS_IS_L64XX(E2) || AXIS_IS_L64XX(E3) || AXIS_IS_L64XX(E4) || AXIS_IS_L64XX(E5) || AXIS_IS_L64XX(E6) || AXIS_IS_L64XX(E7))
-
-#define _EN_ITEM(N) , E##N
-enum L64XX_axis_t : uint8_t { MAIN_AXIS_NAMES, X2, Y2, Z2, Z3, Z4 REPEAT(E_STEPPERS, _EN_ITEM), MAX_L64XX };
-#undef _EN_ITEM
-
-class L64XX_Marlin : public L64XXHelper {
-public:
-  static PGM_P const index_to_axis[MAX_L64XX];
-
-  static const uint8_t index_to_dir[MAX_L64XX];
-
-  static uint8_t dir_commands[MAX_L64XX];
-
-  // Flags to guarantee graceful switch if stepper interrupts L6470 SPI transfer
-  static volatile uint8_t spi_abort;
-  static uint8_t spi_active;
-
-  L64XX_Marlin() {}
-
-  static void init();
-  static void init_to_defaults();
-
-  static uint16_t get_stepper_status(L64XX &st);
-
-  static uint16_t get_status(const L64XX_axis_t axis);
-
-  static uint32_t get_param(const L64XX_axis_t axis, const uint8_t param);
-
-  static void set_param(const L64XX_axis_t axis, const uint8_t param, const uint32_t value);
-
-  //static void send_command(const L64XX_axis_t axis, uint8_t command);
-
-  static uint8_t get_user_input(uint8_t &driver_count, L64XX_axis_t axis_index[3], char axis_mon[3][3],
-                            float &position_max, float &position_min, float &final_feedrate, uint8_t &kval_hold,
-                            uint8_t over_current_flag, uint8_t &OCD_TH_val, uint8_t &STALL_TH_val, uint16_t &over_current_threshold);
-
-  static void transfer(uint8_t L6470_buf[], const uint8_t length);
-
-  static void say_axis(const L64XX_axis_t axis, const uint8_t label=true);
-  #if ENABLED(L6470_CHITCHAT)
-    static void error_status_decode(
-      const uint16_t status, const L64XX_axis_t axis,
-      const uint16_t _status_axis_th_sd, const uint16_t _status_axis_th_wrn,
-      const uint16_t _status_axis_step_loss_a, const uint16_t _status_axis_step_loss_b,
-      const uint16_t _status_axis_ocd, const uint8_t _status_axis_layout
-    );
-  #else
-    FORCE_INLINE static void error_status_decode(
-      const uint16_t, const L64XX_axis_t,
-      const uint16_t, const uint16_t,
-      const uint16_t, const uint16_t,
-      const uint16_t, const uint8_t
-    ){}
-  #endif
-
-  // ~40 bytes SRAM to simplify status decode routines
-  typedef struct {
-    uint8_t STATUS_AXIS_LAYOUT;              // Copy of L6470_status_layout
-    uint8_t AXIS_OCD_TH_MAX;              // Size of OCD_TH field
-    uint8_t AXIS_STALL_TH_MAX;            // Size of STALL_TH field
-    float AXIS_OCD_CURRENT_CONSTANT_INV;   // mA per count
-    float AXIS_STALL_CURRENT_CONSTANT_INV; // mA per count
-    uint8_t L6470_AXIS_CONFIG,            // Address of the CONFIG register
-            L6470_AXIS_STATUS;            // Address of the STATUS register
-    uint16_t L6470_ERROR_MASK,            // STATUS_UVLO | STATUS_TH_WRN | STATUS_TH_SD  | STATUS_OCD | STATUS_STEP_LOSS_A | STATUS_STEP_LOSS_B
-             L6474_ERROR_MASK,            // STATUS_UVLO | STATUS_TH_WRN | STATUS_TH_SD  | STATUS_OCD
-             STATUS_AXIS_RAW,             // Copy of status register contents
-             STATUS_AXIS,                 // Copy of status register contents but with all error bits active low
-             STATUS_AXIS_OCD,             // Overcurrent detected bit position
-             STATUS_AXIS_SCK_MOD,         // Step clock mode is active bit position
-             STATUS_AXIS_STEP_LOSS_A,     // Stall detected on A bridge bit position
-             STATUS_AXIS_STEP_LOSS_B,     // Stall detected on B bridge bit position
-             STATUS_AXIS_TH_SD,           // Thermal shutdown bit position
-             STATUS_AXIS_TH_WRN,          // Thermal warning bit position
-             STATUS_AXIS_UVLO,            // Undervoltage lockout is active bit position
-             STATUS_AXIS_WRONG_CMD,       // Last command not valid bit position
-             STATUS_AXIS_CMD_ERR,         // Command error bit position
-             STATUS_AXIS_NOTPERF_CMD;     // Last command not performed bit position
-  } L64XX_shadow_t;
-
-  static L64XX_shadow_t shadow;
-
-  #if ENABLED(MONITOR_L6470_DRIVER_STATUS)
-    static bool monitor_paused;
-    static void pause_monitor(const bool p) { monitor_paused = p; }
-    static void monitor_update(L64XX_axis_t stepper_index);
-    static void monitor_driver();
-  #else
-    static void pause_monitor(const bool) {}
-  #endif
-
-//protected:
-  // L64XXHelper methods
-  static void spi_init();
-  static uint8_t transfer_single(uint8_t data, int16_t ss_pin);
-  static uint8_t transfer_chain(uint8_t data, int16_t ss_pin, uint8_t chain_position);
-
-private:
-  static void append_stepper_err(char* &p, const uint8_t stepper_index, const char * const err=nullptr);
-
-};
-
-void echo_yes_no(const bool yes);
-
-extern L64XX_Marlin L64xxManager;

Marlin/src/libs/L64XX/README.md

@@ -1,98 +0,0 @@
-### L64XX Stepper Driver
-
-*Arduino-L6470* library revision 0.8.0 or above is required.
-
-This software can be used with the L6470, L6474, L6480 and the powerSTEP01 (collectively referred to as "L64xx" from now on). Different drivers can be mixed within a system.
-
-These devices use voltage PWMs to drive the stepper phases. On the L6474 the phase current is controlled by the `TVAL` register. On all the other drivers the phase current is indirectly controlled via the `KVAL_HOLD` register which scales the PWM duty cycle.
-
-This software assumes that all drivers are in one SPI daisy chain.
-
-### Hardware Setup
-
-- MOSI from controller tied to SDI on the first device
-
-- SDO of the first device is tied to SDI of the next device
-
-- SDO of the last device is tied to MISO of the controller
-
-- All devices share the same `SCK_PIN` and `SS_PIN` pins. The user must supply a macro to control the `RESET_PIN`(s).
-
-- Each L6470 passes the data it saw on its SDI to its neighbor on the **NEXT** SPI cycle (8 bit delay).
-
-- Each L6470 acts on the **last** SPI data it saw when the `SS_PIN` **goes high**.
-
-The L6474 uses the standard STEP DIR interface. Phase currents are changed in response to step pulses. The direction is set by the DIR pin. Instead of an ENA pin, stepper power is controlled with SPI commands.
-
-The other drivers operate in `STEP_CLOCK` mode. In this mode the Direction / Enable functions are done with SPI commands and the phase currents are changed in response to STEP pulses.
-
-### Hardware / Software Interaction
-
-Except for the L6474, powering up a stepper and setting the direction are done by the same command. You can't do one without the other.
-
-**All** directions are set **every time** a new block is popped off the queue by the stepper ISR.
-
-When setting direction, SPI transfers are minimized by using arrays and a specialized SPI method. *Arduino-L6470* library calls are not used. For N L64xx drivers, this results in N bytes transferred. If library calls were used then N<sup>2</sup> bytes would be sent.
-
-### Power-up (Reset) Sequence
-
-- Stepper objects are instantiated before the `setup()` entry point is reached.
-
-- In `setup()` (before stepper drivers are initialized) the `L6470_init()` method is called to do the following:
-
-  - If present, pulse the hardware reset pin.
-
-  - Populate the `L6470_chain` array, which maps positions in the SPI stream to commands/data for L64XX stepper drivers.
-
-  - Initialize the L64XX Software SPI pin states.
-
-  - Initialize L64XX drivers. They may be reset later by a call to `L6470_init_to_defaults()`.
-
-The steppers are **NOT** powered up (enabled) during this sequence.
-
-### `L6470_chain` array
-
-This array is used by all routines that transmit SPI data. For a chain with N devices, the array contains:
-
-Index|Value
------|-----
-0|Number of drivers in chain
-1|Axis index of the first device in the chain (closest to MOSI)
-...|
-N|Axis index of the last device chain (closest to MISO)
-
-### Set Direction and Enable
-
-The `DIR_WRITE` macros for the L64xx drivers are written so that the standard X, Y, Z and extruder logic used by the `set_directions()` routine is not altered. These macros write the correct forward/reverse command to the corresponding location in the array `L6470_dir_commands`. On the L6474 the array the command used just enables the stepper because direction is set by the DIR pin.
-
-At the end of the `set_directions()` routine, the array `L6470_chain` is used to grab the corresponding direction/enable commands out of the array `L6470_dir_commands` and put them in the correct sequence in the array `L6470_buf`. Array `L6470_buf` is then passed to the **`void`** `L6470_Transfer` function which actually sends the data to the devices.
-
-### Utilities, etc.
-
-The **absolute position** registers should accurately reflect Marlin’s stepper position counts. They are set to zero during initialization. `G28` sets them to the Marlin counts for the corresponding axis after homing. NOTE: These registers are often the negative of the Marlin counts. This is because the Marlin counts reflect the logical direction while the registers reflect the stepper direction. The register contents are displayed via the `M114 D` command.
-
-The `L6470_monitor` feature reads the status of each device every half second. It will report if there are any error conditions present or if communications has been lost/restored. The `KVAL_HOLD` value is reduced every 2 – 2.5 seconds if the thermal warning or thermal shutdown conditions are present.
-
-**M122** displays the settings of most of the bits in the status register plus a couple of other items.
-
-**M906** can be used to set the `KVAL_HOLD` register (`TVAL` on L6474) one driver at a time. If a setting is not included with the command then the contents of the registers that affect the phase current/voltage are displayed.
-
-**M916, M917 & M918**
-
-These utilities are used to tune the system. They can get you in the ballpark for acceptable jerk, acceleration, top speed and `KVAL_HOLD` settings (`TVAL` on L6474). In general they seem to provide an overly optimistic `KVAL_HOLD` (`TVAL`) setting because of the lag between setting `KVAL_HOLD` (`TVAL`) and the driver reaching final temperature. Enabling the `L6470_monitor` feature during prints will provide the **final useful setting**.
-
-The amount of power needed to move the stepper without skipping steps increases as jerk, acceleration, top speed, and micro-steps increase. The power dissipated by the driver increases as the power to the stepper increases. The net result is a balancing act between jerk, acceleration, top speed, micro-steps, and power dissipated by the driver.
-
-**M916** - Increases `KVAL_HOLD` (`TVAL`) while moving one axis until a thermal warning is generated. This routine is also useful for determining the approximate `KVAL_HOLD` (`TVAL`) where the stepper stops losing steps. The sound will get noticeably quieter as it stops losing steps.
-
-**M917** - Find minimum current thresholds. This is accomplished by doing the following steps while moving an axis:
-
-1. Decrease OCD current until overcurrent error.
-
-2. Increase OCD until overcurrent error goes away.
-
-3. Decrease stall threshold until stall error (not available on the L6474).
-
-4. Increase stall until stall error goes away (not available on the L6474).
-
-**M918** - Increase speed until error or max feedrate achieved.

Marlin/src/module/stepper.cpp

@@ -117,12 +117,6 @@ Stepper stepper; // Singleton
   #include "../feature/runout.h"
 #endif
 
-#if HAS_L64XX
-  #include "../libs/L64XX/L64XX_Marlin.h"
-  uint8_t L6470_buf[MAX_L64XX + 1];   // chip command sequence - element 0 not used
-  bool L64XX_OK_to_power_up = false;  // flag to keep L64xx steppers powered down after a reset or power up
-#endif
-
 #if ENABLED(AUTO_POWER_CONTROL)
   #include "../feature/power.h"
 #endif
@@ -618,27 +612,6 @@ void Stepper::set_directions() {
     #endif
   #endif // !LIN_ADVANCE
 
-  #if HAS_L64XX
-    if (L64XX_OK_to_power_up) { // OK to send the direction commands (which powers up the L64XX steppers)
-      if (L64xxManager.spi_active) {
-        L64xxManager.spi_abort = true;                    // Interrupted SPI transfer needs to shut down gracefully
-        for (uint8_t j = 1; j <= L64XX::chain[0]; j++)
-          L6470_buf[j] = dSPIN_NOP;                         // Fill buffer with NOOPs
-        L64xxManager.transfer(L6470_buf, L64XX::chain[0]);  // Send enough NOOPs to complete any command
-        L64xxManager.transfer(L6470_buf, L64XX::chain[0]);
-        L64xxManager.transfer(L6470_buf, L64XX::chain[0]);
-      }
-
-      // L64xxManager.dir_commands[] is an array that holds direction command for each stepper
-
-      // Scan command array, copy matches into L64xxManager.transfer
-      for (uint8_t j = 1; j <= L64XX::chain[0]; j++)
-        L6470_buf[j] = L64xxManager.dir_commands[L64XX::chain[j]];
-
-      L64xxManager.transfer(L6470_buf, L64XX::chain[0]);  // send the command stream to the drivers
-    }
-  #endif
-
   DIR_WAIT_AFTER();
 }
 
@@ -2351,13 +2324,11 @@ uint32_t Stepper::block_phase_isr() {
         else LA_isr_rate = LA_ADV_NEVER;
       #endif
 
-      if ( ENABLED(HAS_L64XX)       // Always set direction for L64xx (Also enables the chips)
-        || ENABLED(DUAL_X_CARRIAGE) // TODO: Find out why this fixes "jittery" small circles
+      if ( ENABLED(DUAL_X_CARRIAGE) // TODO: Find out why this fixes "jittery" small circles
         || current_block->direction_bits != last_direction_bits
         || TERN(MIXING_EXTRUDER, false, stepper_extruder != last_moved_extruder)
       ) {
         E_TERN_(last_moved_extruder = stepper_extruder);
-        TERN_(HAS_L64XX, L64XX_OK_to_power_up = true);
         set_directions(current_block->direction_bits);
       }
 

Marlin/src/module/stepper/L64xx.cpp

@@ -1,264 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
-/**
- * stepper/L64xx.cpp
- * Stepper driver indirection for L64XX drivers
- */
-
-#include "../../inc/MarlinConfig.h"
-
-#if HAS_L64XX
-
-#include "L64xx.h"
-
-#if AXIS_IS_L64XX(X)
-  L64XX_CLASS(X) stepperX(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(X2)
-  L64XX_CLASS(X2) stepperX2(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(Y)
-  L64XX_CLASS(Y) stepperY(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(Y2)
-  L64XX_CLASS(Y2) stepperY2(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(Z)
-  L64XX_CLASS(Z) stepperZ(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(Z2)
-  L64XX_CLASS(Z2) stepperZ2(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(Z3)
-  L64XX_CLASS(Z3) stepperZ3(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(Z4)
-  L64XX_CLASS(Z4) stepperZ4(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(I)
-  L64XX_CLASS(I) stepperI(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(J)
-  L64XX_CLASS(J) stepperJ(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(K)
-  L64XX_CLASS(K) stepperK(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(U)
-  L64XX_CLASS(u) stepperU(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(V)
-  L64XX_CLASS(v) stepperV(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(W)
-  L64XX_CLASS(w) stepperW(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E0)
-  L64XX_CLASS(E0) stepperE0(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E1)
-  L64XX_CLASS(E1) stepperE1(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E2)
-  L64XX_CLASS(E2) stepperE2(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E3)
-  L64XX_CLASS(E3) stepperE3(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E4)
-  L64XX_CLASS(E4) stepperE4(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E5)
-  L64XX_CLASS(E5) stepperE5(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E6)
-  L64XX_CLASS(E6) stepperE6(L6470_CHAIN_SS_PIN);
-#endif
-#if AXIS_IS_L64XX(E7)
-  L64XX_CLASS(E7) stepperE7(L6470_CHAIN_SS_PIN);
-#endif
-
-// Not using L64XX class init method because it
-// briefly sends power to the steppers
-
-inline void L6470_init_chip(L64XX &st, const int ms, const int oc, const int sc, const int mv, const int slew_rate) {
-  st.set_handlers(L64xxManager.spi_init, L64xxManager.transfer_single, L64xxManager.transfer_chain);  // specify which external SPI routines to use
-  switch (st.L6470_status_layout) {
-    case L6470_STATUS_LAYOUT: {
-      st.resetDev();
-      st.softFree();
-      st.SetParam(st.L64XX_CONFIG, CONFIG_PWM_DIV_1 | CONFIG_PWM_MUL_2 | CONFIG_OC_SD_DISABLE | CONFIG_VS_COMP_DISABLE | CONFIG_SW_HARD_STOP | CONFIG_INT_16MHZ);
-      st.SetParam(L6470_KVAL_RUN, 0xFF);
-      st.SetParam(L6470_KVAL_ACC, 0xFF);
-      st.SetParam(L6470_KVAL_DEC, 0xFF);
-      st.setMicroSteps(ms);
-      st.setOverCurrent(oc);
-      st.setStallCurrent(sc);
-      st.SetParam(L6470_KVAL_HOLD, mv);
-      st.SetParam(L6470_ABS_POS, 0);
-      uint32_t config_temp = st.GetParam(st.L64XX_CONFIG);
-      config_temp &= ~CONFIG_POW_SR;
-      switch (slew_rate) {
-        case 0: st.SetParam(st.L64XX_CONFIG, config_temp | CONFIG_SR_75V_us); break;
-        default:
-        case 1: st.SetParam(st.L64XX_CONFIG, config_temp | CONFIG_SR_110V_us); break;
-        case 3:
-        case 2: st.SetParam(st.L64XX_CONFIG, config_temp | CONFIG_SR_260V_us); break;
-      }
-      st.getStatus();
-      st.getStatus();
-      break;
-    }
-
-    case L6474_STATUS_LAYOUT: {
-      st.free();
-      //st.SetParam(st.L64XX_CONFIG, CONFIG_PWM_DIV_1 | CONFIG_PWM_MUL_2 | CONFIG_OC_SD_DISABLE | CONFIG_VS_COMP_DISABLE | CONFIG_SW_HARD_STOP | CONFIG_INT_16MHZ);
-      //st.SetParam(L6474_TVAL, 0xFF);
-      st.setMicroSteps(ms);
-      st.setOverCurrent(oc);
-      st.setTVALCurrent(sc);
-      st.SetParam(L6470_ABS_POS, 0);
-      uint32_t config_temp = st.GetParam(st.L64XX_CONFIG);
-      config_temp &= ~CONFIG_POW_SR & ~CONFIG_EN_TQREG;  // clear out slew rate and set current to be controlled by TVAL register
-      switch (slew_rate) {
-        case 0: st.SetParam(st.L64XX_CONFIG, config_temp | CONFIG_SR_75V_us); break;
-        default:
-        case 1: st.SetParam(st.L64XX_CONFIG, config_temp | CONFIG_SR_110V_us); break;
-        case 3:
-        case 2: st.SetParam(st.L64XX_CONFIG, config_temp | CONFIG_SR_260V_us); break;
-        //case 0: st.SetParam(st.L64XX_CONFIG, 0x2E88 | CONFIG_EN_TQREG | CONFIG_SR_75V_us); break;
-        //default:
-        //case 1: st.SetParam(st.L64XX_CONFIG, 0x2E88 | CONFIG_EN_TQREG | CONFIG_SR_110V_us); break;
-        //case 3:
-        //case 2: st.SetParam(st.L64XX_CONFIG, 0x2E88 | CONFIG_EN_TQREG | CONFIG_SR_260V_us); break;
-
-        //case 0: st.SetParam(st.L64XX_CONFIG, 0x2E88 ); break;
-        //default:
-        //case 1: st.SetParam(st.L64XX_CONFIG, 0x2E88 ); break;
-        //case 3:
-        //case 2: st.SetParam(st.L64XX_CONFIG, 0x2E88 ); break;
-      }
-      st.getStatus();
-      st.getStatus();
-      break;
-    }
-
-    case L6480_STATUS_LAYOUT: {
-      st.resetDev();
-      st.softFree();
-      st.SetParam(st.L64XX_CONFIG, CONFIG_PWM_DIV_1 | CONFIG_PWM_MUL_2 | CONFIG_OC_SD_DISABLE | CONFIG_VS_COMP_DISABLE | CONFIG_SW_HARD_STOP | CONFIG_INT_16MHZ);
-      st.SetParam(L6470_KVAL_RUN, 0xFF);
-      st.SetParam(L6470_KVAL_ACC, 0xFF);
-      st.SetParam(L6470_KVAL_DEC, 0xFF);
-      st.setMicroSteps(ms);
-      st.setOverCurrent(oc);
-      st.setStallCurrent(sc);
-      st.SetParam(+-L6470_KVAL_HOLD, mv);
-      st.SetParam(L6470_ABS_POS, 0);
-      st.SetParam(st.L64XX_CONFIG,(st.GetParam(st.L64XX_CONFIG) | PWR_VCC_7_5V));
-      st.getStatus();     // must clear out status bits before can set slew rate
-      st.getStatus();
-      switch (slew_rate) {
-        case 0: st.SetParam(L6470_GATECFG1, CONFIG1_SR_220V_us); st.SetParam(L6470_GATECFG2, CONFIG2_SR_220V_us); break;
-        default:
-        case 1: st.SetParam(L6470_GATECFG1, CONFIG1_SR_400V_us); st.SetParam(L6470_GATECFG2, CONFIG2_SR_400V_us); break;
-        case 2: st.SetParam(L6470_GATECFG1, CONFIG1_SR_520V_us); st.SetParam(L6470_GATECFG2, CONFIG2_SR_520V_us); break;
-        case 3: st.SetParam(L6470_GATECFG1, CONFIG1_SR_980V_us); st.SetParam(L6470_GATECFG2, CONFIG2_SR_980V_us); break;
-      }
-      break;
-    }
-  }
-}
-
-#define L6470_INIT_CHIP(Q) L6470_init_chip(stepper##Q, Q##_MICROSTEPS, Q##_OVERCURRENT, Q##_STALLCURRENT, Q##_MAX_VOLTAGE, Q##_SLEW_RATE)
-
-void L64XX_Marlin::init_to_defaults() {
-  #if AXIS_IS_L64XX(X)
-    L6470_INIT_CHIP(X);
-  #endif
-  #if AXIS_IS_L64XX(X2)
-    L6470_INIT_CHIP(X2);
-  #endif
-  #if AXIS_IS_L64XX(Y)
-    L6470_INIT_CHIP(Y);
-  #endif
-  #if AXIS_IS_L64XX(Y2)
-    L6470_INIT_CHIP(Y2);
-  #endif
-  #if AXIS_IS_L64XX(Z)
-    L6470_INIT_CHIP(Z);
-  #endif
-  #if AXIS_IS_L64XX(Z2)
-    L6470_INIT_CHIP(Z2);
-  #endif
-  #if AXIS_IS_L64XX(Z3)
-    L6470_INIT_CHIP(Z3);
-  #endif
-  #if AXIS_IS_L64XX(Z4)
-    L6470_INIT_CHIP(Z4);
-  #endif
-  #if AXIS_IS_L64XX(I)
-    L6470_INIT_CHIP(I);
-  #endif
-  #if AXIS_IS_L64XX(J)
-    L6470_INIT_CHIP(J);
-  #endif
-  #if AXIS_IS_L64XX(K)
-    L6470_INIT_CHIP(K);
-  #endif
-  #if AXIS_IS_L64XX(U)
-    L6470_INIT_CHIP(U);
-  #endif
-  #if AXIS_IS_L64XX(V)
-    L6470_INIT_CHIP(V);
-  #endif
-  #if AXIS_IS_L64XX(W)
-    L6470_INIT_CHIP(W);
-  #endif
-  #if AXIS_IS_L64XX(E0)
-    L6470_INIT_CHIP(E0);
-  #endif
-  #if AXIS_IS_L64XX(E1)
-    L6470_INIT_CHIP(E1);
-  #endif
-  #if AXIS_IS_L64XX(E2)
-    L6470_INIT_CHIP(E2);
-  #endif
-  #if AXIS_IS_L64XX(E3)
-    L6470_INIT_CHIP(E3);
-  #endif
-  #if AXIS_IS_L64XX(E4)
-    L6470_INIT_CHIP(E4);
-  #endif
-  #if AXIS_IS_L64XX(E5)
-    L6470_INIT_CHIP(E5);
-  #endif
-  #if AXIS_IS_L64XX(E6)
-    L6470_INIT_CHIP(E6);
-  #endif
-  #if AXIS_IS_L64XX(E7)
-    L6470_INIT_CHIP(E7);
-  #endif
-}
-
-#endif // HAS_L64XX

Marlin/src/module/stepper/L64xx.h

@@ -1,490 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * stepper/L64xx.h
- * Stepper driver indirection for L64XX drivers
- */
-
-#include "../../inc/MarlinConfig.h"
-#include "../../libs/L64XX/L64XX_Marlin.h"
-
-// Convert option names to L64XX classes
-#define CLASS_L6470       L6470
-#define CLASS_L6474       L6474
-#define CLASS_POWERSTEP01 powerSTEP01
-
-#define __L64XX_CLASS(TYPE) CLASS_##TYPE
-#define _L64XX_CLASS(TYPE)  __L64XX_CLASS(TYPE)
-#define L64XX_CLASS(ST)     _L64XX_CLASS(ST##_DRIVER_TYPE)
-
-#define L6474_DIR_WRITE(A,STATE) do{ L64xxManager.dir_commands[A] = dSPIN_L6474_ENABLE; WRITE(A##_DIR_PIN, STATE); }while(0)
-#define L64XX_DIR_WRITE(A,STATE) do{ L64xxManager.dir_commands[A] = (STATE) ? dSPIN_STEP_CLOCK_REV : dSPIN_STEP_CLOCK_FWD; }while(0)
-
-// X Stepper
-#if AXIS_IS_L64XX(X)
-  extern L64XX_CLASS(X)         stepperX;
-  #define X_ENABLE_INIT()       NOOP
-  #define X_ENABLE_WRITE(STATE) (STATE ? stepperX.hardStop() : stepperX.free())
-  #define X_ENABLE_READ()       (stepperX.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_X(L6474)
-    #define X_DIR_INIT()        SET_OUTPUT(X_DIR_PIN)
-    #define X_DIR_WRITE(STATE)  L6474_DIR_WRITE(X, STATE)
-    #define X_DIR_READ()        READ(X_DIR_PIN)
-  #else
-    #define X_DIR_INIT()        NOOP
-    #define X_DIR_WRITE(STATE)  L64XX_DIR_WRITE(X, STATE)
-    #define X_DIR_READ()        (stepper##X.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_X(L6470)
-      #define DISABLE_STEPPER_X() stepperX.free()
-    #endif
-  #endif
-#endif
-
-// Y Stepper
-#if AXIS_IS_L64XX(Y)
-  extern L64XX_CLASS(Y)         stepperY;
-  #define Y_ENABLE_INIT()       NOOP
-  #define Y_ENABLE_WRITE(STATE) (STATE ? stepperY.hardStop() : stepperY.free())
-  #define Y_ENABLE_READ()       (stepperY.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_Y(L6474)
-    #define Y_DIR_INIT()        SET_OUTPUT(Y_DIR_PIN)
-    #define Y_DIR_WRITE(STATE)  L6474_DIR_WRITE(Y, STATE)
-    #define Y_DIR_READ()        READ(Y_DIR_PIN)
-  #else
-    #define Y_DIR_INIT()        NOOP
-    #define Y_DIR_WRITE(STATE)  L64XX_DIR_WRITE(Y, STATE)
-    #define Y_DIR_READ()        (stepper##Y.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_Y(L6470)
-      #define DISABLE_STEPPER_Y() stepperY.free()
-    #endif
-  #endif
-#endif
-
-// Z Stepper
-#if AXIS_IS_L64XX(Z)
-  extern L64XX_CLASS(Z)         stepperZ;
-  #define Z_ENABLE_INIT()       NOOP
-  #define Z_ENABLE_WRITE(STATE) (STATE ? stepperZ.hardStop() : stepperZ.free())
-  #define Z_ENABLE_READ()       (stepperZ.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_Z(L6474)
-    #define Z_DIR_INIT()        SET_OUTPUT(Z_DIR_PIN)
-    #define Z_DIR_WRITE(STATE)  L6474_DIR_WRITE(Z, STATE)
-    #define Z_DIR_READ()        READ(Z_DIR_PIN)
-  #else
-    #define Z_DIR_INIT()        NOOP
-    #define Z_DIR_WRITE(STATE)  L64XX_DIR_WRITE(Z, STATE)
-    #define Z_DIR_READ()        (stepper##Z.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_Z(L6470)
-      #define DISABLE_STEPPER_Z() stepperZ.free()
-    #endif
-  #endif
-#endif
-
-// X2 Stepper
-#if HAS_X2_ENABLE && AXIS_IS_L64XX(X2)
-  extern L64XX_CLASS(X2)         stepperX2;
-  #define X2_ENABLE_INIT()       NOOP
-  #define X2_ENABLE_WRITE(STATE) (STATE ? stepperX2.hardStop() : stepperX2.free())
-  #define X2_ENABLE_READ()       (stepperX2.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_X2(L6474)
-    #define X2_DIR_INIT()        SET_OUTPUT(X2_DIR_PIN)
-    #define X2_DIR_WRITE(STATE)  L6474_DIR_WRITE(X2, STATE)
-    #define X2_DIR_READ()        READ(X2_DIR_PIN)
-  #else
-    #define X2_DIR_INIT()        NOOP
-    #define X2_DIR_WRITE(STATE)  L64XX_DIR_WRITE(X2, STATE)
-    #define X2_DIR_READ()        (stepper##X2.getStatus() & STATUS_DIR);
-  #endif
-#endif
-
-#if AXIS_DRIVER_TYPE_X2(L6470)
-  #define DISABLE_STEPPER_X2() stepperX2.free()
-#endif
-
-// Y2 Stepper
-#if HAS_Y2_ENABLE && AXIS_IS_L64XX(Y2)
-  extern L64XX_CLASS(Y2)         stepperY2;
-  #define Y2_ENABLE_INIT()       NOOP
-  #define Y2_ENABLE_WRITE(STATE) (STATE ? stepperY2.hardStop() : stepperY2.free())
-  #define Y2_ENABLE_READ()       (stepperY2.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_Y2(L6474)
-    #define Y2_DIR_INIT()        SET_OUTPUT(Y2_DIR_PIN)
-    #define Y2_DIR_WRITE(STATE)  L6474_DIR_WRITE(Y2, STATE)
-    #define Y2_DIR_READ()        READ(Y2_DIR_PIN)
-  #else
-    #define Y2_DIR_INIT()        NOOP
-    #define Y2_DIR_WRITE(STATE)  L64XX_DIR_WRITE(Y2, STATE)
-    #define Y2_DIR_READ()        (stepper##Y2.getStatus() & STATUS_DIR);
-  #endif
-#endif
-
-#if AXIS_DRIVER_TYPE_Y2(L6470)
-  #define DISABLE_STEPPER_Y2() stepperY2.free()
-#endif
-
-// Z2 Stepper
-#if HAS_Z2_ENABLE && AXIS_IS_L64XX(Z2)
-  extern L64XX_CLASS(Z2)         stepperZ2;
-  #define Z2_ENABLE_INIT()       NOOP
-  #define Z2_ENABLE_WRITE(STATE) (STATE ? stepperZ2.hardStop() : stepperZ2.free())
-  #define Z2_ENABLE_READ()       (stepperZ2.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_Z2(L6474)
-    #define Z2_DIR_INIT()        SET_OUTPUT(Z2_DIR_PIN)
-    #define Z2_DIR_WRITE(STATE)  L6474_DIR_WRITE(Z2, STATE)
-    #define Z2_DIR_READ()        READ(Z2_DIR_PIN)
-  #else
-    #define Z2_DIR_INIT()        NOOP
-    #define Z2_DIR_WRITE(STATE)  L64XX_DIR_WRITE(Z2, STATE)
-    #define Z2_DIR_READ()        (stepper##Z2.getStatus() & STATUS_DIR);
-  #endif
-#endif
-
-#if AXIS_DRIVER_TYPE_Z2(L6470)
-  #define DISABLE_STEPPER_Z2() stepperZ2.free()
-#endif
-
-// Z3 Stepper
-#if HAS_Z3_ENABLE && AXIS_IS_L64XX(Z3)
-  extern L64XX_CLASS(Z3)         stepperZ3;
-  #define Z3_ENABLE_INIT()       NOOP
-  #define Z3_ENABLE_WRITE(STATE) (STATE ? stepperZ3.hardStop() : stepperZ3.free())
-  #define Z3_ENABLE_READ()       (stepperZ3.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_Z3(L6474)
-    #define Z3_DIR_INIT()        SET_OUTPUT(Z3_DIR_PIN)
-    #define Z3_DIR_WRITE(STATE)  L6474_DIR_WRITE(Z3, STATE)
-    #define Z3_DIR_READ()        READ(Z3_DIR_PIN)
-  #else
-    #define Z3_DIR_INIT()        NOOP
-    #define Z3_DIR_WRITE(STATE)  L64XX_DIR_WRITE(Z3, STATE)
-    #define Z3_DIR_READ()        (stepper##Z3.getStatus() & STATUS_DIR);
-  #endif
-#endif
-
-#if AXIS_DRIVER_TYPE_Z3(L6470)
-  #define DISABLE_STEPPER_Z3() stepperZ3.free()
-#endif
-
-// Z4 Stepper
-#if HAS_Z4_ENABLE && AXIS_IS_L64XX(Z4)
-  extern L64XX_CLASS(Z4)         stepperZ4;
-  #define Z4_ENABLE_INIT()       NOOP
-  #define Z4_ENABLE_WRITE(STATE) (STATE ? stepperZ4.hardStop() : stepperZ4.free())
-  #define Z4_ENABLE_READ()       (stepperZ4.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_Z4(L6474)
-    #define Z4_DIR_INIT()        SET_OUTPUT(Z4_DIR_PIN)
-    #define Z4_DIR_WRITE(STATE)  L6474_DIR_WRITE(Z4, STATE)
-    #define Z4_DIR_READ()        READ(Z4_DIR_PIN)
-  #else
-    #define Z4_DIR_INIT()        NOOP
-    #define Z4_DIR_WRITE(STATE)  L64XX_DIR_WRITE(Z4, STATE)
-    #define Z4_DIR_READ()        (stepper##Z4.getStatus() & STATUS_DIR);
-  #endif
-#endif
-
-#if AXIS_DRIVER_TYPE_Z4(L6470)
-  #define DISABLE_STEPPER_Z4() stepperZ4.free()
-#endif
-
-// I Stepper
-#if AXIS_IS_L64XX(I)
-  extern L64XX_CLASS(I)         stepperI;
-  #define I_ENABLE_INIT()       NOOP
-  #define I_ENABLE_WRITE(STATE) (STATE ? stepperI.hardStop() : stepperI.free())
-  #define I_ENABLE_READ()       (stepperI.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_I(L6474)
-    #define I_DIR_INIT()        SET_OUTPUT(I_DIR_PIN)
-    #define I_DIR_WRITE(STATE)  L6474_DIR_WRITE(I, STATE)
-    #define I_DIR_READ()        READ(I_DIR_PIN)
-  #else
-    #define I_DIR_INIT()        NOOP
-    #define I_DIR_WRITE(STATE)  L64XX_DIR_WRITE(I, STATE)
-    #define I_DIR_READ()        (stepper##I.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_I(L6470)
-      #define DISABLE_STEPPER_I() stepperI.free()
-    #endif
-  #endif
-#endif
-
-// J Stepper
-#if AXIS_IS_L64XX(J)
-  extern L64XX_CLASS(J)         stepperJ;
-  #define J_ENABLE_INIT()       NOOP
-  #define J_ENABLE_WRITE(STATE) (STATE ? stepperJ.hardStop() : stepperJ.free())
-  #define J_ENABLE_READ()       (stepperJ.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_J(L6474)
-    #define J_DIR_INIT()        SET_OUTPUT(J_DIR_PIN)
-    #define J_DIR_WRITE(STATE)  L6474_DIR_WRITE(J, STATE)
-    #define J_DIR_READ()        READ(J_DIR_PIN)
-  #else
-    #define J_DIR_INIT()        NOOP
-    #define J_DIR_WRITE(STATE)  L64XX_DIR_WRITE(J, STATE)
-    #define J_DIR_READ()        (stepper##J.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_J(L6470)
-      #define DISABLE_STEPPER_J() stepperJ.free()
-    #endif
-  #endif
-#endif
-
-// K Stepper
-#if AXIS_IS_L64XX(K)
-  extern L64XX_CLASS(K)         stepperK;
-  #define K_ENABLE_INIT()       NOOP
-  #define K_ENABLE_WRITE(STATE) (STATE ? stepperK.hardStop() : stepperK.free())
-  #define K_ENABLE_READ()       (stepperK.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_K(L6474)
-    #define K_DIR_INIT()        SET_OUTPUT(K_DIR_PIN)
-    #define K_DIR_WRITE(STATE)  L6474_DIR_WRITE(K, STATE)
-    #define K_DIR_READ()        READ(K_DIR_PIN)
-  #else
-    #define K_DIR_INIT()        NOOP
-    #define K_DIR_WRITE(STATE)  L64XX_DIR_WRITE(K, STATE)
-    #define K_DIR_READ()        (stepper##K.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_K(L6470)
-      #define DISABLE_STEPPER_K() stepperK.free()
-    #endif
-  #endif
-#endif
-
-// U Stepper
-#if HAS_U_AXIS
-  #if AXIS_IS_L64XX(U)
-    extern L64XX_CLASS(U)         stepperU;
-    #define U_ENABLE_INIT()       NOOP
-    #define U_ENABLE_WRITE(STATE) (STATE ? stepperU.hardStop() : stepperU.free())
-    #define U_ENABLE_READ()       (stepperU.getStatus() & STATUS_HIZ)
-    #if AXIS_DRIVER_TYPE_U(L6474)
-      #define U_DIR_INIT()        SET_OUTPUT(U_DIR_PIN)
-      #define U_DIR_WRITE(STATE)  L6474_DIR_WRITE(U, STATE)
-      #define U_DIR_READ()        READ(U_DIR_PIN)
-    #else
-      #define U_DIR_INIT()        NOOP
-      #define U_DIR_WRITE(STATE)  L64XX_DIR_WRITE(U, STATE)
-      #define U_DIR_READ()        (stepper##U.getStatus() & STATUS_DIR);
-      #if AXIS_DRIVER_TYPE_U(L6470)
-        #define DISABLE_STEPPER_U() stepperU.free()
-      #endif
-    #endif
-  #endif
-#endif
-
-// V Stepper
-#if HAS_V_AXIS
-  #if AXIS_IS_L64XX(V)
-    extern L64XX_CLASS(V)         stepperV;
-    #define V_ENABLE_INIT()       NOOP
-    #define V_ENABLE_WRITE(STATE) (STATE ? stepperV.hardStop() : stepperV.free())
-    #define V_ENABLE_READ()       (stepperV.getStatus() & STATUS_HIZ)
-    #if AXIS_DRIVER_TYPE_V(L6474)
-      #define V_DIR_INIT()        SET_OUTPUT(V_DIR_PIN)
-      #define V_DIR_WRITE(STATE)  L6474_DIR_WRITE(V, STATE)
-      #define V_DIR_READ()        READ(V_DIR_PIN)
-    #else
-      #define V_DIR_INIT()        NOOP
-      #define V_DIR_WRITE(STATE)  L64XX_DIR_WRITE(V, STATE)
-      #define V_DIR_READ()        (stepper##V.getStatus() & STATUS_DIR);
-      #if AXIS_DRIVER_TYPE_V(L6470)
-        #define DISABLE_STEPPER_V() stepperV.free()
-      #endif
-    #endif
-  #endif
-#endif
-
-// W Stepper
-#if HAS_W_AXIS
-  #if AXIS_IS_L64XX(W)
-    extern L64XX_CLASS(w)         stepperW;
-    #define W_ENABLE_INIT()       NOOP
-    #define W_ENABLE_WRITE(STATE) (STATE ? stepperW.hardStop() : stepperW.free())
-    #define W_ENABLE_READ()       (stepperW.getStatus() & STATUS_HIZ)
-    #if AXIS_DRIVER_TYPE_W(L6474)
-      #define W_DIR_INIT()        SET_OUTPUT(W_DIR_PIN)
-      #define W_DIR_WRITE(STATE)  L6474_DIR_WRITE(W, STATE)
-      #define W_DIR_READ()        READ(W_DIR_PIN)
-    #else
-      #define W_DIR_INIT()        NOOP
-      #define W_DIR_WRITE(STATE)  L64XX_DIR_WRITE(W, STATE)
-      #define W_DIR_READ()        (stepper##W.getStatus() & STATUS_DIR);
-      #if AXIS_DRIVER_TYPE_W(L6470)
-        #define DISABLE_STEPPER_W() stepperW.free()
-      #endif
-    #endif
-  #endif
-#endif
-
-// E0 Stepper
-#if AXIS_IS_L64XX(E0)
-  extern L64XX_CLASS(E0)         stepperE0;
-  #define E0_ENABLE_INIT()       NOOP
-  #define E0_ENABLE_WRITE(STATE)  (STATE ? stepperE0.hardStop() : stepperE0.free())
-  #define E0_ENABLE_READ()       (stepperE0.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E0(L6474)
-    #define E0_DIR_INIT()        SET_OUTPUT(E0_DIR_PIN)
-    #define E0_DIR_WRITE(STATE)  L6474_DIR_WRITE(E0, STATE)
-    #define E0_DIR_READ()        READ(E0_DIR_PIN)
-  #else
-    #define E0_DIR_INIT()        NOOP
-    #define E0_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E0, STATE)
-    #define E0_DIR_READ()        (stepper##E0.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E0(L6470)
-      #define DISABLE_STEPPER_E0() do{ stepperE0.free(); }while(0)
-    #endif
-  #endif
-#endif
-
-// E1 Stepper
-#if AXIS_IS_L64XX(E1)
-  extern L64XX_CLASS(E1)         stepperE1;
-  #define E1_ENABLE_INIT()       NOOP
-  #define E1_ENABLE_WRITE(STATE) (STATE ? stepperE1.hardStop() : stepperE1.free())
-  #define E1_ENABLE_READ()       (stepperE1.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E1(L6474)
-    #define E1_DIR_INIT()        SET_OUTPUT(E1_DIR_PIN)
-    #define E1_DIR_WRITE(STATE)  L6474_DIR_WRITE(E1, STATE)
-    #define E1_DIR_READ()        READ(E1_DIR_PIN)
-  #else
-    #define E1_DIR_INIT()        NOOP
-    #define E1_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E1, STATE)
-    #define E1_DIR_READ()        (stepper##E1.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E1(L6470)
-      #define DISABLE_STEPPER_E1() do{ stepperE1.free(); }while(0)
-    #endif
-  #endif
-#endif
-
-// E2 Stepper
-#if AXIS_IS_L64XX(E2)
-  extern L64XX_CLASS(E2)         stepperE2;
-  #define E2_ENABLE_INIT()       NOOP
-  #define E2_ENABLE_WRITE(STATE) (STATE ? stepperE2.hardStop() : stepperE2.free())
-  #define E2_ENABLE_READ()       (stepperE2.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E2(L6474)
-    #define E2_DIR_INIT()        SET_OUTPUT(E2_DIR_PIN)
-    #define E2_DIR_WRITE(STATE)  L6474_DIR_WRITE(E2, STATE)
-    #define E2_DIR_READ()        READ(E2_DIR_PIN)
-  #else
-    #define E2_DIR_INIT()        NOOP
-    #define E2_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E2, STATE)
-    #define E2_DIR_READ()        (stepper##E2.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E2(L6470)
-      #define DISABLE_STEPPER_E2() do{ stepperE2.free(); }while(0)
-    #endif
-  #endif
-#endif
-
-// E3 Stepper
-#if AXIS_IS_L64XX(E3)
-  extern L64XX_CLASS(E3)         stepperE3;
-  #define E3_ENABLE_INIT()       NOOP
-  #define E3_ENABLE_WRITE(STATE) (STATE ? stepperE3.hardStop() : stepperE3.free())
-  #define E3_ENABLE_READ()       (stepperE3.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E3(L6474)
-    #define E3_DIR_INIT()        SET_OUTPUT(E3_DIR_PIN)
-    #define E3_DIR_WRITE(STATE)  L6474_DIR_WRITE(E3, STATE)
-    #define E3_DIR_READ()        READ(E3_DIR_PIN)
-  #else
-    #define E3_DIR_INIT()        NOOP
-    #define E3_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E3, STATE)
-    #define E3_DIR_READ()        (stepper##E3.getStatus() & STATUS_DIR);
-  #endif
-#endif
-
-// E4 Stepper
-#if AXIS_IS_L64XX(E4)
-  extern L64XX_CLASS(E4)         stepperE4;
-  #define E4_ENABLE_INIT()       NOOP
-  #define E4_ENABLE_WRITE(STATE) (STATE ? stepperE4.hardStop() : stepperE4.free())
-  #define E4_ENABLE_READ()       (stepperE4.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E4(L6474)
-    #define E4_DIR_INIT()        SET_OUTPUT(E4_DIR_PIN)
-    #define E4_DIR_WRITE(STATE)  L6474_DIR_WRITE(E4, STATE)
-    #define E4_DIR_READ()        READ(E4_DIR_PIN)
-  #else
-    #define E4_DIR_INIT()        NOOP
-    #define E4_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E4, STATE)
-    #define E4_DIR_READ()        (stepper##E4.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E4(L6470)
-      #define DISABLE_STEPPER_E4() do{ stepperE4.free(); }while(0)
-    #endif
-  #endif
-#endif
-
-// E5 Stepper
-#if AXIS_IS_L64XX(E5)
-  extern L64XX_CLASS(E5)         stepperE5;
-  #define E5_ENABLE_INIT()       NOOP
-  #define E5_ENABLE_WRITE(STATE) (STATE ? stepperE5.hardStop() : stepperE5.free())
-  #define E5_ENABLE_READ()       (stepperE5.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E5(L6474)
-    #define E5_DIR_INIT()        SET_OUTPUT(E5_DIR_PIN)
-    #define E5_DIR_WRITE(STATE)  L6474_DIR_WRITE(E5, STATE)
-    #define E5_DIR_READ()        READ(E5_DIR_PIN)
-  #else
-    #define E5_DIR_INIT()        NOOP
-    #define E5_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E5, STATE)
-    #define E5_DIR_READ()        (stepper##E5.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E5(L6470)
-      #define DISABLE_STEPPER_E5() do{ stepperE5.free(); }while(0)
-    #endif
-  #endif
-#endif
-
-// E6 Stepper
-#if AXIS_IS_L64XX(E6)
-  extern L64XX_CLASS(E6)         stepperE6;
-  #define E6_ENABLE_INIT()       NOOP
-  #define E6_ENABLE_WRITE(STATE) (STATE ? stepperE6.hardStop() : stepperE6.free())
-  #define E6_ENABLE_READ()       (stepperE6.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E6(L6474)
-    #define E6_DIR_INIT()        SET_OUTPUT(E6_DIR_PIN)
-    #define E6_DIR_WRITE(STATE)  L6474_DIR_WRITE(E6, STATE)
-    #define E6_DIR_READ()        READ(E6_DIR_PIN)
-  #else
-    #define E6_DIR_INIT()        NOOP
-    #define E6_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E6, STATE)
-    #define E6_DIR_READ()        (stepper##E6.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E6(L6470)
-      #define DISABLE_STEPPER_E6() do{ stepperE6.free(); }while(0)
-    #endif
-  #endif
-#endif
-
-// E7 Stepper
-#if AXIS_IS_L64XX(E7)
-  extern L64XX_CLASS(E7)         stepperE7;
-  #define E7_ENABLE_INIT()       NOOP
-  #define E7_ENABLE_WRITE(STATE) (STATE ? stepperE7.hardStop() : stepperE7.free())
-  #define E7_ENABLE_READ()       (stepperE7.getStatus() & STATUS_HIZ)
-  #if AXIS_DRIVER_TYPE_E7(L6474)
-    #define E7_DIR_INIT()        SET_OUTPUT(E7_DIR_PIN)
-    #define E7_DIR_WRITE(STATE)  L6474_DIR_WRITE(E7, STATE)
-    #define E7_DIR_READ()        READ(E7_DIR_PIN)
-  #else
-    #define E7_DIR_INIT()        NOOP
-    #define E7_DIR_WRITE(STATE)  L64XX_DIR_WRITE(E7, STATE)
-    #define E7_DIR_READ()        (stepper##E7.getStatus() & STATUS_DIR);
-    #if AXIS_DRIVER_TYPE_E7(L6470)
-      #define DISABLE_STEPPER_E7() do{ stepperE7.free(); }while(0)
-    #endif
-  #endif
-#endif

Marlin/src/module/stepper/indirection.cpp

@@ -38,7 +38,6 @@ void restore_stepper_drivers() {
 
 void reset_stepper_drivers() {
   TERN_(HAS_TMC26X, tmc26x_init_to_defaults());
-  TERN_(HAS_L64XX, L64xxManager.init_to_defaults());
   TERN_(HAS_TRINAMIC_CONFIG, reset_trinamic_drivers());
 }
 

Marlin/src/module/stepper/indirection.h

@@ -32,10 +32,6 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if HAS_L64XX
-  #include "L64xx.h"
-#endif
-
 #if HAS_TMC26X
   #include "TMC26X.h"
 #endif

Marlin/src/pins/pins.h

@@ -629,8 +629,6 @@
   #include "stm32f4/pins_RUMBA32_BTT.h"         // STM32F4                                env:rumba32
 #elif MB(BLACK_STM32F407VE)
   #include "stm32f4/pins_BLACK_STM32F407VE.h"   // STM32F4                                env:STM32F407VE_black
-#elif MB(STEVAL_3DP001V1)
-  #include "stm32f4/pins_STEVAL_3DP001V1.h"     // STM32F4                                env:STM32F401VE_STEVAL
 #elif MB(BTT_SKR_PRO_V1_1)
   #include "stm32f4/pins_BTT_SKR_PRO_V1_1.h"    // STM32F4                                env:BIGTREE_SKR_PRO env:BIGTREE_SKR_PRO_usb_flash_drive
 #elif MB(BTT_SKR_PRO_V1_2)
@@ -786,6 +784,7 @@
   #define BOARD_STM32F103R              99906
   #define BOARD_ESP32                   99907
   #define BOARD_STEVAL                  99908
+  #define BOARD_STEVAL_3DP001V1         99908
   #define BOARD_BIGTREE_SKR_V1_1        99909
   #define BOARD_BIGTREE_SKR_V1_3        99910
   #define BOARD_BIGTREE_SKR_V1_4        99911
@@ -841,7 +840,7 @@
   #elif MOTHERBOARD == BOARD_ESP32
     #error "BOARD_ESP32 has been renamed BOARD_ESPRESSIF_ESP32. Please update your configuration."
   #elif MB(STEVAL)
-    #error "BOARD_STEVAL has been renamed BOARD_STEVAL_3DP001V1. Please update your configuration."
+    #error "BOARD_STEVAL_3DP001V1 (BOARD_STEVAL) is no longer supported in Marlin."
   #elif MB(RUMBA32)
     #error "BOARD_RUMBA32 is now BOARD_RUMBA32_MKS or BOARD_RUMBA32_V1_0. Please update your configuration."
   #elif MB(RUMBA32_AUS3D)
@@ -873,7 +872,7 @@
   #undef BOARD_STM32F103R
   #undef BOARD_ESP32
   #undef BOARD_STEVAL
-  #undef BOARD_BIGTREE_SKR_MINI_E3
+  #undef BOARD_STEVAL_3DP001V1
   #undef BOARD_BIGTREE_SKR_V1_1
   #undef BOARD_BIGTREE_SKR_V1_3
   #undef BOARD_BIGTREE_SKR_V1_4
@@ -881,6 +880,7 @@
   #undef BOARD_BIGTREE_BTT002_V1_0
   #undef BOARD_BIGTREE_SKR_PRO_V1_1
   #undef BOARD_BIGTREE_SKR_MINI_V1_1
+  #undef BOARD_BIGTREE_SKR_MINI_E3
   #undef BOARD_BIGTREE_SKR_E3_DIP
   #undef BOARD_RUMBA32
   #undef BOARD_RUMBA32_AUS3D

Marlin/src/pins/pinsDebug_list.h

@@ -1826,21 +1826,6 @@
 #if PIN_EXISTS(K_SERIAL_RX)
   REPORT_NAME_DIGITAL(__LINE__, K_SERIAL_RX_PIN)
 #endif
-#if PIN_EXISTS(L6470_CHAIN_SCK)
-  REPORT_NAME_DIGITAL(__LINE__, L6470_CHAIN_SCK_PIN)
-#endif
-#if PIN_EXISTS(L6470_CHAIN_MISO)
-  REPORT_NAME_DIGITAL(__LINE__, L6470_CHAIN_MISO_PIN)
-#endif
-#if PIN_EXISTS(L6470_CHAIN_MOSI)
-  REPORT_NAME_DIGITAL(__LINE__, L6470_CHAIN_MOSI_PIN)
-#endif
-#if PIN_EXISTS(L6470_CHAIN_SS)
-  REPORT_NAME_DIGITAL(__LINE__, L6470_CHAIN_SS_PIN)
-#endif
-#if PIN_EXISTS(L6470_RESET_CHAIN)
-  REPORT_NAME_DIGITAL(__LINE__, L6470_RESET_CHAIN_PIN)
-#endif
 #if PIN_EXISTS(FET_SAFETY)
   REPORT_NAME_DIGITAL(__LINE__, FET_SAFETY_PIN)
 #endif

Marlin/src/pins/stm32f4/pins_STEVAL_3DP001V1.h

@@ -1,325 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-// Source: https://github.com/stm32duino/Arduino_Core_STM32/blob/master/variants/ST3DP001_EVAL/variant.cpp
-
-/**
- * HOW TO COMPILE
- *
- * PlatformIO - Use the STM32F401VE_STEVAL environment (or the "Auto Build Marlin" extension).
- *
- * Arduino - Tested with 1.8.10
- *      Install library per https://github.com/stm32duino/Arduino_Core_STM32
- *      Make the following selections under the TOOL menu in the Arduino IDE
- *          Board: "3D printer boards"
- *          Board part number: "STEVAL-3DP001V1"
- *          U(S)ART support: "Enabled (generic "Serial")"
- *          USB support (if available): "CDC (no generic "Serial")"
- *          Optimize: "Smallest (-Os default)"
- *          C Runtime Library: "newlib Nano (default)"
- */
-
-#include "env_validate.h"
-
-#ifndef MACHINE_NAME
-  #define MACHINE_NAME "STEVAL-3DP001V1"
-#endif
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN                           PD8   // X_STOP
-#define Y_MIN_PIN                           PD9   // Y_STOP
-#define Z_MIN_PIN                           PD10  // Z_STOP
-
-#define X_MAX_PIN                           PD0   // W_STOP
-#define Y_MAX_PIN                           PA8   // V_STOP
-#define Z_MAX_PIN                           PD11  // U_STOP
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-//#ifndef Z_MIN_PROBE_PIN
-//  #define Z_MIN_PROBE_PIN                 PA4   // SPI1_CS
-//#endif
-
-//
-// Filament runout
-//
-//#define FIL_RUNOUT_PIN                    PA3   // BED_THERMISTOR_3
-
-//
-// Steppers
-//
-
-#define X_STEP_PIN                          PE14  // X_PWM
-#define X_DIR_PIN                           PE15  // X_DIR
-#define X_ENABLE_PIN                        PE13  // X_RESET
-#define X_CS_PIN                            PA4   // SPI1_CS
-
-#define Y_STEP_PIN                          PB10  // Y_PWM
-#define Y_DIR_PIN                           PE9   // Y_DIR
-#define Y_ENABLE_PIN                        PE10  // Y_RESET
-#define Y_CS_PIN                            PA4   // SPI1_CS
-
-#define Z_STEP_PIN                          PC6   // Z_PWM
-#define Z_DIR_PIN                           PC0   // Z_DIR
-#define Z_ENABLE_PIN                        PC15  // Z_RESET
-#define Z_CS_PIN                            PA4   // SPI1_CS
-
-#define E0_STEP_PIN                         PD12  // E1_PW
-#define E0_DIR_PIN                          PC13  // E1_DIR
-#define E0_ENABLE_PIN                       PC14  // E1_RESET
-#define E0_CS_PIN                           PA4   // SPI1_CS
-
-#define E1_STEP_PIN                         PE5   // E2_PWM
-#define E1_DIR_PIN                          PE6   // E2_DIR
-#define E1_ENABLE_PIN                       PE4   // E2_RESET
-#define E1_CS_PIN                           PA4   // SPI1_CS
-
-#define E2_STEP_PIN                         PB8   // E3_PWM
-#define E2_DIR_PIN                          PE2   // E3_DIR
-#define E2_ENABLE_PIN                       PE3   // E3_RESET
-#define E2_CS_PIN                           PA4   // SPI1_CS
-
-// needed to pass a sanity check
-#define X2_CS_PIN                           PA4   // SPI1_CS
-#define Y2_CS_PIN                           PA4   // SPI1_CS
-#define Z2_CS_PIN                           PA4   // SPI1_CS
-#define Z3_CS_PIN                           PA4   // SPI1_CS
-#define E3_CS_PIN                           PA4   // SPI1_CS
-#define E4_CS_PIN                           PA4   // SPI1_CS
-#define E5_CS_PIN                           PA4   // SPI1_CS
-
-#if HAS_L64XX
-  #define L6470_CHAIN_SCK_PIN               PA5   // SPI1_SCK
-  #define L6470_CHAIN_MISO_PIN              PA6   // SPI1_MISO
-  #define L6470_CHAIN_MOSI_PIN              PA7   // SPI1_MOSI
-  #define L6470_CHAIN_SS_PIN                PA4   // SPI1_CS
-
-  //#define SD_SCK_PIN       L6470_CHAIN_SCK_PIN
-  //#define SD_MISO_PIN     L6470_CHAIN_MISO_PIN
-  //#define SD_MOSI_PIN     L6470_CHAIN_MOSI_PIN
-#else
-  //#define SD_SCK_PIN                      PB13  // SPI2_SCK
-  //#define SD_MISO_PIN                     PB14  // SPI2_MISO
-  //#define SD_MOSI_PIN                     PB15  // SPI2_MOSI
-#endif
-
-/**
- * Macro to reset/enable L6474 stepper drivers
- *
- * IMPORTANT - To disable (bypass) L6474s, install the corresponding
- *             resistors (R11 - R17) and change the "V" to "0" for the
- *             corresponding pins here:
- */
-#define ENABLE_RESET_L64XX_CHIPS(V)   do{ OUT_WRITE(X_ENABLE_PIN, V); \
-                                          OUT_WRITE(Y_ENABLE_PIN, V); \
-                                          OUT_WRITE(Z_ENABLE_PIN, V); \
-                                          OUT_WRITE(E0_ENABLE_PIN,V); \
-                                          OUT_WRITE(E1_ENABLE_PIN,V); \
-                                          OUT_WRITE(E2_ENABLE_PIN,V); \
-                                        }while(0)
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN                          PA0   // Analog Input 3
-#define TEMP_1_PIN                          PA1   // Analog Input 4
-#define TEMP_2_PIN                          PA2   // Analog Input 5
-#define TEMP_BED_PIN                        PC2   // Analog Input 0
-#define TEMP_BED_1_PIN                      PC3   // Analog Input 1
-#define TEMP_BED_2_PIN                      PA3   // Analog Input 2
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN                        PC7   // E1_HEAT_PWM
-#define HEATER_1_PIN                        PB0   // E2_HEAT_PWM
-#define HEATER_2_PIN                        PB1   // E3_HEAT_PWM
-#define HEATER_BED_PIN                      PD14  // BED_HEAT_1 FET
-#define HEATER_BED_1_PIN                    PD13  // BED_HEAT_2 FET
-#define HEATER_BED_2_PIN                    PD15  // BED_HEAT_3 FET
-
-#define FAN_PIN                             PC4   // E1_FAN   PWM pin, Part cooling fan FET
-#define FAN1_PIN                            PC5   // E2_FAN   PWM pin, Extruder fan FET
-#define FAN2_PIN                            PE8   // E3_FAN   PWM pin, Controller fan FET
-
-#ifndef E0_AUTO_FAN_PIN
-  #define E0_AUTO_FAN_PIN                   PC5   // FAN1_PIN
-#endif
-
-//
-// Misc functions
-//
-#define LED_PIN                             -1    // PE1  Green LED Heartbeat
-#define PS_ON_PIN                           -1
-#define KILL_PIN                            -1
-#define POWER_LOSS_PIN                      -1    // PWR_LOSS / nAC_FAULT
-
-//
-// LCD / Controller
-//
-//#define SD_DETECT_PIN                     PA15  // SD_CARD_DETECT
-//#define BEEPER_PIN                        PC9   // SDIO_D1
-//#define LCD_PINS_RS                       PE9   // Y_DIR
-//#define LCD_PINS_ENABLE                   PE8   // E3_FAN
-//#define LCD_PINS_D4                       PB12  // SPI2_CS
-//#define LCD_PINS_D5                       PB13  // SPI2_SCK
-//#define LCD_PINS_D6                       PB14  // SPI2_MISO
-//#define LCD_PINS_D7                       PB15  // SPI2_MOSI
-//#define BTN_EN1                           PC4   // E1_FAN
-//#define BTN_EN2                           PC5   // E2_FAN
-//#define BTN_ENC                           PC3   // BED_THERMISTOR_2
-
-//
-// Extension pins
-//
-//#define EXT0_PIN                          PB0   // E2_HEAT
-//#define EXT1_PIN                          PB1   // E3_HEAT
-//#define EXT2_PIN                          PB2   // not used (tied to ground)
-//#define EXT3_PIN                          PD8   // X_STOP
-//#define EXT4_PIN                          PD9   // Y_STOP
-//#define EXT5_PIN                          PD10  // Z_STOP
-//#define EXT6_PIN                          PD11  // U_STOP
-//#define EXT7_PIN                          PD12  // E1_PWM
-//#define EXT8_PIN                          PB10  // Y_PWM
-
-// WIFI
-// PD3   CTS
-// PD4   RTS
-// PD5   TX
-// PD6   RX
-// PB5   WIFI_WAKEUP
-// PE11  WIFI_RESET
-// PE12  WIFI_BOOT
-
-// I2C USER
-// PB7   SDA
-// PB6   SCL
-
-// JTAG
-// PA13  JTAG_TMS/SWDIO
-// PA14  JTAG_TCK/SWCLK
-// PB3   JTAG_TDO/SWO
-
-//
-// Onboard SD support
-//
-#ifndef SDCARD_CONNECTION
-  #define SDCARD_CONNECTION              ONBOARD
-#endif
-
-#if SD_CONNECTION_IS(ONBOARD)
-
-  #define SDIO_SUPPORT                            // Use SDIO for onboard SD
-  #if DISABLED(SDIO_SUPPORT)
-    #define SOFTWARE_SPI                          // Use soft SPI for onboard SD
-    #define SDSS                            PC11
-    #define SD_SCK_PIN                      PC12
-    #define SD_MISO_PIN                     PC8
-    #define SD_MOSI_PIN                     PD2
-  #endif
-
-  //#define SD_DETECT_PIN                   PA15
-
-#endif
-
-#ifndef SDSS
-  #define SDSS                              PA4   // SPI1_CS
-#endif
-
-// OTG
-// PA11   OTG_DM
-// PA12   OTG_DP
-
-// USER_PINS
-// PD7    USER3
-// PB9    USER1
-// PE0    USER2
-// PB4    USER4
-
-// USERKET
-// PE7    USER_BUTTON
-
-// PA9    TX
-// PA10   RX
-
-// IR/PROBE
-// PD1    IR_OUT
-// PC1    IR_ON
-
-/**
- * Logical pin vs. port/pin cross reference
- *
- * PA0    E1_THERMISTOR           PD0    W_STOP
- * PA1    E2_THERMISTOR           PD1    IR_OUT
- * PA2    E3_THERMISTOR           PD2    SDIO_CMD
- * PA3    BED_THERMISTOR_3        PD3    CTS
- * PA4    SPI1_CS                 PD4    RTS
- * PA5    SPI1_SCK                PD5    TX
- * PA6    SPI1_MISO               PD6    RX
- * PA7    SPI1_MOSI               PD7    USER3
- * PA8    V_STOP                  PD8    X_STOP
- * PA9    TX                      PD9    Y_STOP
- * PA10   RX                      PD10   Z_STOP
- * PA11   OTG_DM                  PD11   U_STOP
- * PA12   OTG_DP                  PD12   E1_PWM
- * PA13   JTAG_TMS/SWDIO          PD13   BED_HEAT_2
- * PA14   JTAG_TCK/SWCLK          PD14   BED_HEAT_1
- * PA15   SD_CARD_DETECT          PD15   BED_HEAT_3
- *
- * PB0    E2_HEAT_PWM             PE0    USER2
- * PB1    E3_HEAT_PWM             PE1    STATUS_LED
- * PB2    ---                     PE2    E3_DIR
- * PB3    JTAG_TDO/SWO            PE3    E3_RESET
- * PB4    USER4                   PE4    E2_RESET
- * PB5    WIFI_WAKEUP             PE5    E2_PWM
- * PB6    SCL                     PE6    E2_DIR
- * PB7    SDA                     PE7    USER_BUTTON
- * PB8    E3_PWM                  PE8    E3_FAN
- * PB9    USER1                   PE9    Y_DIR
- * PB10   Y_PWM                   PE10   Y_RESET
- * PB11   ---                     PE11   WIFI_RESET
- * PB12   SPI2_CS                 PE12   WIFI_BOOT
- * PB13   SPI2_SCK                PE13   X_RESET
- * PB14   SPI2_MISO               PE14   X_PWM
- * PB15   SPI2_MOSI               PE15   X_DIR
- *
- * PC0    Z_DIR
- * PC1    IR_ON
- * PC2    BED_THERMISTOR_1
- * PC3    BED_THERMISTOR_2
- * PC4    E1_FAN
- * PC5    E2_FAN
- * PC6    Z_PWM
- * PC7    E1_HEAT_PWM
- * PC8    SDIO_D0
- * PC9    SDIO_D1
- * PC10   SDIO_D2
- * PC11   SDIO_D3
- * PC12   SDIO_CK
- * PC13   E1_DIR
- * PC14   E1_RESET
- * PC15   Z_RESET
- */

buildroot/share/PlatformIO/boards/marlin_STEVAL_STM32F401VE.json

@@ -1,64 +0,0 @@
-{
-  "build": {
-    "core": "stm32",
-    "cpu": "cortex-m4",
-    "extra_flags": "-DSTM32F401xx -DARDUINO_STEVAL",
-    "f_cpu": "84000000L",
-    "hwids": [
-      [
-        "0x1EAF",
-        "0x0003"
-      ],
-      [
-        "0x0483",
-        "0x3748"
-      ]
-    ],
-    "mcu": "stm32f401vet6",
-    "variant": "MARLIN_STEVAL_F401VE"
-  },
-  "debug": {
-    "jlink_device": "STM32F401VE",
-    "openocd_target": "stm32f4x",
-    "svd_path": "STM32F40x.svd",
-    "tools": {
-      "stlink": {
-        "server": {
-          "arguments": [
-            "-f",
-            "scripts/interface/stlink.cfg",
-            "-c",
-            "transport select hla_swd",
-            "-f",
-            "scripts/target/stm32f4x.cfg",
-            "-c",
-            "reset_config none"
-          ],
-          "executable": "bin/openocd",
-          "package": "tool-openocd"
-        }
-      }
-    }
-  },
-  "frameworks": [
-    "arduino",
-    "stm32cube"
-  ],
-  "name": "STM32F401VE (96k RAM. 512k Flash)",
-  "upload": {
-    "disable_flushing": false,
-    "maximum_ram_size": 98304,
-    "maximum_size": 514288,
-    "protocol": "stlink",
-    "protocols": [
-      "stlink",
-      "dfu",
-      "jlink"
-    ],
-    "require_upload_port": true,
-    "use_1200bps_touch": false,
-    "wait_for_upload_port": false
-  },
-  "url": "https://www.st.com/en/evaluation-tools/steval-3dp001v1.html",
-  "vendor": "Generic"
-}

buildroot/share/PlatformIO/variants/MARLIN_STEVAL_F401VE/PeripheralPins.c

@@ -1,260 +0,0 @@
-
-/*
- *******************************************************************************
- * Copyright (c) 2019, STMicroelectronics
- * All rights reserved.
- *
- * This software component is licensed by ST under BSD 3-Clause license,
- * the "License"; You may not use this file except in compliance with the
- * License. You may obtain a copy of the License at:
- *                        opensource.org/licenses/BSD-3-Clause
- *
- *******************************************************************************
- * Automatically generated from STM32F401V(D-E)Tx.xml
- */
-#include "Arduino.h"
-#include "PeripheralPins.h"
-
-/* =====
- * Note: Commented lines are alternative possibilities which are not used per default.
- *       If you change them, you will have to know what you do
- * =====
- */
-
-//*** ADC ***
-
-#ifdef HAL_ADC_MODULE_ENABLED
-WEAK const PinMap PinMap_ADC[] = {
-  {PA_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
-  {PA_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
-  {PA_2,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
-  {PA_3,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
-  //{PA_4,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
-  //{PA_5,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
-  //{PA_6,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
-  //{PA_7,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
-  //{PB_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
-  //{PB_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
-  //{PC_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
-  //{PC_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
-  {PC_2,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
-  {PC_3,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
-  //{PC_4,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
-  //{PC_5,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
-  {NC,    NP,    0}
-};
-#endif
-
-//*** No DAC ***
-
-//*** I2C ***
-
-#ifdef HAL_I2C_MODULE_ENABLED
-WEAK const PinMap PinMap_I2C_SDA[] = {
-  //{PB_3,  I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C2)},
-  //{PB_4,  I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)},
-  {PB_7,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
-  //{PB_9,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
-  //{PC_9,  I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_I2C_SCL[] = {
-  //{PA_8,  I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
-  {PB_6,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
-  //{PB_8,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
-  //{PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
-  {NC,    NP,    0}
-};
-#endif
-
-//*** PWM ***
-
-#ifdef HAL_TIM_MODULE_ENABLED
-WEAK const PinMap PinMap_PWM[] = {
-  //{PA_0,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
-  //{PA_0,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
-  //{PA_1,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
-  //{PA_1,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
-  //{PA_2,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
-  //{PA_2,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3
-  //{PA_2,  TIM9,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
-  //{PA_3,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
-  //{PA_3,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4
-  //{PA_3,  TIM9,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
-  //{PA_5,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
-  //{PA_6,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
-  //{PA_7,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
-  //{PA_7,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
-  //{PA_8,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
-  //{PA_9,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
-  //{PA_10, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
-  //{PA_11, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
-  //{PA_15, TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
-  //{PB_0,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
-  {PB_0,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
-  //{PB_1,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
-  {PB_1,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
-  //{PB_3,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
-  //{PB_4,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
-  //{PB_5,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
-  //{PB_6,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
-  //{PB_7,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
-  //{PB_8,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
-  //{PB_8,  TIM10,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
-  //{PB_9,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
-  //{PB_9,  TIM11,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
-  {PB_10, TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
-  //{PB_13, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
-  //{PB_14, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
-  //{PB_15, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
-  {PC_6,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
-  {PC_7,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
-  //{PC_8,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
-  //{PC_9,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
-  {PD_12, TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
-  {PD_13, TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
-  {PD_14, TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
-  {PD_15, TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
-  {PE_5,  TIM9,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
-  //{PE_6,  TIM9,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
-  //{PE_8,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
-  //{PE_9,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
-  //{PE_10, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
-  //{PE_11, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
-  //{PE_12, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
-  //{PE_13, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
-  {PE_14, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
-  {NC,    NP,    0}
-};
-#endif
-
-//*** SERIAL ***
-
-#ifdef HAL_UART_MODULE_ENABLED
-WEAK const PinMap PinMap_UART_TX[] = {
-  //{PA_2,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  {PA_9,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
-  //{PA_11, USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
-  //{PB_6,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
-  //{PC_6,  USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
-  {PD_5,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_UART_RX[] = {
-  //{PA_3,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  {PA_10, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
-  //{PA_12, USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
-  //{PB_7,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
-  //{PC_7,  USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
-  {PD_6,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_UART_RTS[] = {
-  //{PA_1,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  //{PA_12, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
-  {PD_4,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_UART_CTS[] = {
-  //{PA_0,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  //{PA_11, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
-  {PD_3,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
-  {NC,    NP,    0}
-};
-#endif
-
-//*** SPI ***
-
-#ifdef HAL_SPI_MODULE_ENABLED
-WEAK const PinMap PinMap_SPI_MOSI[] = {
-  {PA_7,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PB_5,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PB_5,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PC_3,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  //{PD_6,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PE_6,  SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  //{PE_14, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_SPI_MISO[] = {
-  {PA_6,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PB_4,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PB_4,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PC_2,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  //{PE_5,  SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  //{PE_13, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_SPI_SCLK[] = {
-  {PA_5,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PB_3,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PB_3,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  //{PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  //{PD_3,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PE_2,  SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  //{PE_12, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  {NC,    NP,    0}
-};
-
-WEAK const PinMap PinMap_SPI_SSEL[] = {
-  {PA_4,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PA_4,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  //{PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
-  //{PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
-  //{PB_9,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
-  //{PE_4,  SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  //{PE_11, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
-  {NC,    NP,    0}
-};
-#endif
-
-//*** No CAN ***
-
-//*** No ETHERNET ***
-
-//*** No QUADSPI ***
-
-//*** USB ***
-
-#ifdef HAL_PCD_MODULE_ENABLED
-WEAK const PinMap PinMap_USB_OTG_FS[] = {
-  //{PA_8,  USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF
-  //{PA_9,  USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS
-  //{PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID
-  {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM
-  {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP
-  {NC,    NP,    0}
-};
-#endif
-
-//*** No USB_OTG_HS ***
-//*** SD ***
-
-#ifdef HAL_SD_MODULE_ENABLED
-WEAK const PinMap PinMap_SD[] = {
-  //{PB_8,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D4
-  //{PB_9,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D5
-  //{PC_6,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D6
-  //{PC_7,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D7
-  {PC_8,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D0
-  {PC_9,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1
-  {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2
-  {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D3
-  {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK
-  {PD_2,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CMD
-  {NC,    NP,    0}
-};
-#endif

buildroot/share/PlatformIO/variants/MARLIN_STEVAL_F401VE/PinNamesVar.h

@@ -1,33 +0,0 @@
-/* SYS_WKUP */
-#ifdef PWR_WAKEUP_PIN1
-  SYS_WKUP1 = PA_0,
-#endif
-#ifdef PWR_WAKEUP_PIN2
-  SYS_WKUP2 = NC,
-#endif
-#ifdef PWR_WAKEUP_PIN3
-  SYS_WKUP3 = NC,
-#endif
-#ifdef PWR_WAKEUP_PIN4
-  SYS_WKUP4 = NC,
-#endif
-#ifdef PWR_WAKEUP_PIN5
-  SYS_WKUP5 = NC,
-#endif
-#ifdef PWR_WAKEUP_PIN6
-  SYS_WKUP6 = NC,
-#endif
-#ifdef PWR_WAKEUP_PIN7
-  SYS_WKUP7 = NC,
-#endif
-#ifdef PWR_WAKEUP_PIN8
-  SYS_WKUP8 = NC,
-#endif
-/* USB */
-#ifdef USBCON
-  USB_OTG_FS_SOF  = PA_8,
-  USB_OTG_FS_VBUS = PA_9,
-  USB_OTG_FS_ID   = PA_10,
-  USB_OTG_FS_DM   = PA_11,
-  USB_OTG_FS_DP   = PA_12,
-#endif

buildroot/share/PlatformIO/variants/MARLIN_STEVAL_F401VE/hal_conf_custom.h

@@ -1,495 +0,0 @@
-/**
-  ******************************************************************************
-  * @file    stm32f4xx_hal_conf.h
-  * @brief   HAL configuration file.
-  ******************************************************************************
-  * @attention
-  *
-  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
-  * All rights reserved.</center></h2>
-  *
-  * This software component is licensed by ST under BSD 3-Clause license,
-  * the "License"; You may not use this file except in compliance with the
-  * License. You may obtain a copy of the License at:
-  *                        opensource.org/licenses/BSD-3-Clause
-  *
-  ******************************************************************************
-  */
-
-/* Define to prevent recursive inclusion -------------------------------------*/
-#ifndef __STM32F4xx_HAL_CONF_CUSTOM
-#define __STM32F4xx_HAL_CONF_CUSTOM
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* Exported types ------------------------------------------------------------*/
-/* Exported constants --------------------------------------------------------*/
-
-/* ########################## Module Selection ############################## */
- /**
-  * @brief This is the list of modules to be used in the HAL driver
-  */
-#define HAL_MODULE_ENABLED
-#define HAL_ADC_MODULE_ENABLED
-#define HAL_CRC_MODULE_ENABLED
-#define HAL_DMA_MODULE_ENABLED
-#define HAL_EXTI_MODULE_ENABLED   // Needed for Endstop (and other external) Interrupts
-#define HAL_FLASH_MODULE_ENABLED
-#define HAL_GPIO_MODULE_ENABLED
-#define HAL_I2C_MODULE_ENABLED
-#define HAL_IWDG_MODULE_ENABLED
-#define HAL_PWR_MODULE_ENABLED
-#define HAL_RCC_MODULE_ENABLED
-#define HAL_RTC_MODULE_ENABLED
-#define HAL_SD_MODULE_ENABLED
-#define HAL_SPI_MODULE_ENABLED
-#define HAL_TIM_MODULE_ENABLED
-#define HAL_CORTEX_MODULE_ENABLED
-//#define HAL_PCD_MODULE_ENABLED // Automatically added if any type of USB is enabled, as in Arduino IDE. (STM32 v3.10700.191028)
-
-//#define HAL_CAN_MODULE_ENABLED
-//#define HAL_CAN_LEGACY_MODULE_ENABLED
-//#define HAL_CEC_MODULE_ENABLED
-//#define HAL_CRYP_MODULE_ENABLED
-//#define HAL_DAC_MODULE_ENABLED
-//#define HAL_DCMI_MODULE_ENABLED
-//#define HAL_DMA2D_MODULE_ENABLED
-//#define HAL_ETH_MODULE_ENABLED
-//#define HAL_NAND_MODULE_ENABLED
-//#define HAL_NOR_MODULE_ENABLED
-//#define HAL_PCCARD_MODULE_ENABLED
-//#define HAL_SRAM_MODULE_ENABLED
-//#define HAL_SDRAM_MODULE_ENABLED
-//#define HAL_HASH_MODULE_ENABLED
-//#define HAL_SMBUS_MODULE_ENABLED
-//#define HAL_I2S_MODULE_ENABLED
-//#define HAL_LTDC_MODULE_ENABLED
-//#define HAL_DSI_MODULE_ENABLED
-//#define HAL_QSPI_MODULE_ENABLED
-//#define HAL_RNG_MODULE_ENABLED
-//#define HAL_SAI_MODULE_ENABLED
-//#define HAL_UART_MODULE_ENABLED // by default
-//#define HAL_USART_MODULE_ENABLED
-//#define HAL_IRDA_MODULE_ENABLED
-//#define HAL_SMARTCARD_MODULE_ENABLED
-//#define HAL_WWDG_MODULE_ENABLED
-//#define HAL_HCD_MODULE_ENABLED
-//#define HAL_FMPI2C_MODULE_ENABLED
-//#define HAL_SPDIFRX_MODULE_ENABLED
-//#define HAL_DFSDM_MODULE_ENABLED
-//#define HAL_LPTIM_MODULE_ENABLED
-//#define HAL_MMC_MODULE_ENABLED
-
-/* ########################## HSE/HSI Values adaptation ##################### */
-/**
-  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
-  *        This value is used by the RCC HAL module to compute the system frequency
-  *        (when HSE is used as system clock source, directly or through the PLL).
-  */
-#ifndef HSE_VALUE
-#define HSE_VALUE              8000000U /*!< Value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#ifndef HSE_STARTUP_TIMEOUT
-#define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
-#endif /* HSE_STARTUP_TIMEOUT */
-
-/**
-  * @brief Internal High Speed oscillator (HSI) value.
-  *        This value is used by the RCC HAL module to compute the system frequency
-  *        (when HSI is used as system clock source, directly or through the PLL).
-  */
-#ifndef HSI_VALUE
-#define HSI_VALUE              16000000U /*!< Value of the Internal oscillator in Hz */
-#endif /* HSI_VALUE */
-
-/**
-  * @brief Internal Low Speed oscillator (LSI) value.
-  */
-#ifndef LSI_VALUE
-#define LSI_VALUE               32000U    /*!< LSI Typical Value in Hz */
-#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
-The real value may vary depending on the variations
-in voltage and temperature. */
-/**
-  * @brief External Low Speed oscillator (LSE) value.
-  */
-#ifndef LSE_VALUE
-#define LSE_VALUE               32768U    /*!< Value of the External Low Speed oscillator in Hz */
-#endif /* LSE_VALUE */
-
-#ifndef LSE_STARTUP_TIMEOUT
-#define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
-#endif /* LSE_STARTUP_TIMEOUT */
-
-/**
-  * @brief External clock source for I2S peripheral
-  *        This value is used by the I2S HAL module to compute the I2S clock source
-  *        frequency, this source is inserted directly through I2S_CKIN pad.
-  */
-#ifndef EXTERNAL_CLOCK_VALUE
-#define EXTERNAL_CLOCK_VALUE     12288000U /*!< Value of the External oscillator in Hz*/
-#endif /* EXTERNAL_CLOCK_VALUE */
-
-/* Tip: To avoid modifying this file each time you need to use different HSE,
-   ===  you can define the HSE value in your toolchain compiler preprocessor. */
-
-/* ########################### System Configuration ######################### */
-/**
-  * @brief This is the HAL system configuration section
-  */
-#if !defined (VDD_VALUE)
-#define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
-#endif
-#if !defined (TICK_INT_PRIORITY)
-#define  TICK_INT_PRIORITY            0x00U /*!< tick interrupt priority */
-#endif
-#if !defined (USE_RTOS)
-#define  USE_RTOS                     0U
-#endif
-#if !defined (PREFETCH_ENABLE)
-#define  PREFETCH_ENABLE              1U
-#endif
-#if !defined (INSTRUCTION_CACHE_ENABLE)
-#define  INSTRUCTION_CACHE_ENABLE     1U
-#endif
-#if !defined (DATA_CACHE_ENABLE)
-#define  DATA_CACHE_ENABLE            1U
-#endif
-
-#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
-#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
-#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
-#define  USE_HAL_CRYP_REGISTER_CALLBACKS        0U /* CRYP register callback disabled      */
-#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
-#define  USE_HAL_DCMI_REGISTER_CALLBACKS        0U /* DCMI register callback disabled      */
-#define  USE_HAL_DFSDM_REGISTER_CALLBACKS       0U /* DFSDM register callback disabled     */
-#define  USE_HAL_DMA2D_REGISTER_CALLBACKS       0U /* DMA2D register callback disabled     */
-#define  USE_HAL_DSI_REGISTER_CALLBACKS         0U /* DSI register callback disabled       */
-#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
-#define  USE_HAL_HASH_REGISTER_CALLBACKS        0U /* HASH register callback disabled      */
-#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
-#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
-#define  USE_HAL_FMPI2C_REGISTER_CALLBACKS      0U /* FMPI2C register callback disabled    */
-#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
-#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
-#define  USE_HAL_LPTIM_REGISTER_CALLBACKS       0U /* LPTIM register callback disabled     */
-#define  USE_HAL_LTDC_REGISTER_CALLBACKS        0U /* LTDC register callback disabled      */
-#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
-#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
-#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
-#define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
-#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
-#define  USE_HAL_QSPI_REGISTER_CALLBACKS        0U /* QSPI register callback disabled      */
-#define  USE_HAL_RNG_REGISTER_CALLBACKS         0U /* RNG register callback disabled       */
-#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
-#define  USE_HAL_SAI_REGISTER_CALLBACKS         0U /* SAI register callback disabled       */
-#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
-#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
-#define  USE_HAL_SDRAM_REGISTER_CALLBACKS       0U /* SDRAM register callback disabled     */
-#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
-#define  USE_HAL_SPDIFRX_REGISTER_CALLBACKS     0U /* SPDIFRX register callback disabled   */
-#define  USE_HAL_SMBUS_REGISTER_CALLBACKS       0U /* SMBUS register callback disabled     */
-#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
-#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
-#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
-#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
-#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
-
-/* ########################## Assert Selection ############################## */
-/**
-  * @brief Uncomment the line below to expanse the "assert_param" macro in the
-  *        HAL drivers code
-  */
-/* #define USE_FULL_ASSERT    1U */
-
-/* ################## Ethernet peripheral configuration ##################### */
-
-/* Section 1 : Ethernet peripheral configuration */
-
-/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
-#define MAC_ADDR0   2U
-#define MAC_ADDR1   0U
-#define MAC_ADDR2   0U
-#define MAC_ADDR3   0U
-#define MAC_ADDR4   0U
-#define MAC_ADDR5   0U
-
-/* Definition of the Ethernet driver buffers size and count */
-#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
-#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
-#define ETH_RXBUFNB                    ((uint32_t)4U)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
-#define ETH_TXBUFNB                    ((uint32_t)4U)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
-
-/* Section 2: PHY configuration section */
-
-/* DP83848_PHY_ADDRESS Address*/
-#define DP83848_PHY_ADDRESS           0x01U
-/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
-#define PHY_RESET_DELAY                 0x000000FFU
-/* PHY Configuration delay */
-#define PHY_CONFIG_DELAY                0x00000FFFU
-
-#define PHY_READ_TO                     0x0000FFFFU
-#define PHY_WRITE_TO                    0x0000FFFFU
-
-/* Section 3: Common PHY Registers */
-
-#define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
-#define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
-
-#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
-#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
-#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
-#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
-#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
-#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
-#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
-#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
-#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
-#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
-
-#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
-#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
-#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
-
-/* Section 4: Extended PHY Registers */
-#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
-
-#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
-#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
-
-/* ################## SPI peripheral configuration ########################## */
-
-/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
- * Activated: CRC code is present inside driver
- * Deactivated: CRC code cleaned from driver
- */
-#ifndef USE_SPI_CRC
-#define USE_SPI_CRC                     0U
-#endif
-
-/* Includes ------------------------------------------------------------------*/
-/**
-  * @brief Include module's header file
-  */
-
-#ifdef HAL_RCC_MODULE_ENABLED
-#include "stm32f4xx_hal_rcc.h"
-#endif /* HAL_RCC_MODULE_ENABLED */
-
-#ifdef HAL_GPIO_MODULE_ENABLED
-#include "stm32f4xx_hal_gpio.h"
-#endif /* HAL_GPIO_MODULE_ENABLED */
-
-#ifdef HAL_EXTI_MODULE_ENABLED
-#include "stm32f4xx_hal_exti.h"
-#endif /* HAL_EXTI_MODULE_ENABLED */
-
-#ifdef HAL_DMA_MODULE_ENABLED
-#include "stm32f4xx_hal_dma.h"
-#endif /* HAL_DMA_MODULE_ENABLED */
-
-#ifdef HAL_CORTEX_MODULE_ENABLED
-#include "stm32f4xx_hal_cortex.h"
-#endif /* HAL_CORTEX_MODULE_ENABLED */
-
-#ifdef HAL_ADC_MODULE_ENABLED
-#include "stm32f4xx_hal_adc.h"
-#endif /* HAL_ADC_MODULE_ENABLED */
-
-#ifdef HAL_CAN_MODULE_ENABLED
-#include "stm32f4xx_hal_can.h"
-#endif /* HAL_CAN_MODULE_ENABLED */
-
-#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
-#include "stm32f4xx_hal_can_legacy.h"
-#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
-
-#ifdef HAL_CRC_MODULE_ENABLED
-#include "stm32f4xx_hal_crc.h"
-#endif /* HAL_CRC_MODULE_ENABLED */
-
-#ifdef HAL_CRYP_MODULE_ENABLED
-#include "stm32f4xx_hal_cryp.h"
-#endif /* HAL_CRYP_MODULE_ENABLED */
-
-#ifdef HAL_DMA2D_MODULE_ENABLED
-#include "stm32f4xx_hal_dma2d.h"
-#endif /* HAL_DMA2D_MODULE_ENABLED */
-
-#ifdef HAL_DAC_MODULE_ENABLED
-#include "stm32f4xx_hal_dac.h"
-#endif /* HAL_DAC_MODULE_ENABLED */
-
-#ifdef HAL_DCMI_MODULE_ENABLED
-#include "stm32f4xx_hal_dcmi.h"
-#endif /* HAL_DCMI_MODULE_ENABLED */
-
-#ifdef HAL_ETH_MODULE_ENABLED
-#include "stm32f4xx_hal_eth.h"
-#endif /* HAL_ETH_MODULE_ENABLED */
-
-#ifdef HAL_FLASH_MODULE_ENABLED
-#include "stm32f4xx_hal_flash.h"
-#endif /* HAL_FLASH_MODULE_ENABLED */
-
-#ifdef HAL_SRAM_MODULE_ENABLED
-#include "stm32f4xx_hal_sram.h"
-#endif /* HAL_SRAM_MODULE_ENABLED */
-
-#ifdef HAL_NOR_MODULE_ENABLED
-#include "stm32f4xx_hal_nor.h"
-#endif /* HAL_NOR_MODULE_ENABLED */
-
-#ifdef HAL_NAND_MODULE_ENABLED
-#include "stm32f4xx_hal_nand.h"
-#endif /* HAL_NAND_MODULE_ENABLED */
-
-#ifdef HAL_PCCARD_MODULE_ENABLED
-#include "stm32f4xx_hal_pccard.h"
-#endif /* HAL_PCCARD_MODULE_ENABLED */
-
-#ifdef HAL_SDRAM_MODULE_ENABLED
-#include "stm32f4xx_hal_sdram.h"
-#endif /* HAL_SDRAM_MODULE_ENABLED */
-
-#ifdef HAL_HASH_MODULE_ENABLED
-#include "stm32f4xx_hal_hash.h"
-#endif /* HAL_HASH_MODULE_ENABLED */
-
-#ifdef HAL_I2C_MODULE_ENABLED
-#include "stm32f4xx_hal_i2c.h"
-#endif /* HAL_I2C_MODULE_ENABLED */
-
-#ifdef HAL_SMBUS_MODULE_ENABLED
-#include "stm32f4xx_hal_smbus.h"
-#endif /* HAL_SMBUS_MODULE_ENABLED */
-
-#ifdef HAL_I2S_MODULE_ENABLED
-#include "stm32f4xx_hal_i2s.h"
-#endif /* HAL_I2S_MODULE_ENABLED */
-
-#ifdef HAL_IWDG_MODULE_ENABLED
-#include "stm32f4xx_hal_iwdg.h"
-#endif /* HAL_IWDG_MODULE_ENABLED */
-
-#ifdef HAL_LTDC_MODULE_ENABLED
-#include "stm32f4xx_hal_ltdc.h"
-#endif /* HAL_LTDC_MODULE_ENABLED */
-
-#ifdef HAL_PWR_MODULE_ENABLED
-#include "stm32f4xx_hal_pwr.h"
-#endif /* HAL_PWR_MODULE_ENABLED */
-
-#ifdef HAL_RNG_MODULE_ENABLED
-#include "stm32f4xx_hal_rng.h"
-#endif /* HAL_RNG_MODULE_ENABLED */
-
-#ifdef HAL_RTC_MODULE_ENABLED
-#include "stm32f4xx_hal_rtc.h"
-#endif /* HAL_RTC_MODULE_ENABLED */
-
-#ifdef HAL_SAI_MODULE_ENABLED
-#include "stm32f4xx_hal_sai.h"
-#endif /* HAL_SAI_MODULE_ENABLED */
-
-#ifdef HAL_SD_MODULE_ENABLED
-#include "stm32f4xx_hal_sd.h"
-#endif /* HAL_SD_MODULE_ENABLED */
-
-#ifdef HAL_SPI_MODULE_ENABLED
-#include "stm32f4xx_hal_spi.h"
-#endif /* HAL_SPI_MODULE_ENABLED */
-
-#ifdef HAL_TIM_MODULE_ENABLED
-#include "stm32f4xx_hal_tim.h"
-#endif /* HAL_TIM_MODULE_ENABLED */
-
-#ifdef HAL_UART_MODULE_ENABLED
-#include "stm32f4xx_hal_uart.h"
-#endif /* HAL_UART_MODULE_ENABLED */
-
-#ifdef HAL_USART_MODULE_ENABLED
-#include "stm32f4xx_hal_usart.h"
-#endif /* HAL_USART_MODULE_ENABLED */
-
-#ifdef HAL_IRDA_MODULE_ENABLED
-#include "stm32f4xx_hal_irda.h"
-#endif /* HAL_IRDA_MODULE_ENABLED */
-
-#ifdef HAL_SMARTCARD_MODULE_ENABLED
-#include "stm32f4xx_hal_smartcard.h"
-#endif /* HAL_SMARTCARD_MODULE_ENABLED */
-
-#ifdef HAL_WWDG_MODULE_ENABLED
-#include "stm32f4xx_hal_wwdg.h"
-#endif /* HAL_WWDG_MODULE_ENABLED */
-
-#ifdef HAL_PCD_MODULE_ENABLED
-#include "stm32f4xx_hal_pcd.h"
-#endif /* HAL_PCD_MODULE_ENABLED */
-
-#ifdef HAL_HCD_MODULE_ENABLED
-#include "stm32f4xx_hal_hcd.h"
-#endif /* HAL_HCD_MODULE_ENABLED */
-
-#ifdef HAL_DSI_MODULE_ENABLED
-#include "stm32f4xx_hal_dsi.h"
-#endif /* HAL_DSI_MODULE_ENABLED */
-
-#ifdef HAL_QSPI_MODULE_ENABLED
-#include "stm32f4xx_hal_qspi.h"
-#endif /* HAL_QSPI_MODULE_ENABLED */
-
-#ifdef HAL_CEC_MODULE_ENABLED
-#include "stm32f4xx_hal_cec.h"
-#endif /* HAL_CEC_MODULE_ENABLED */
-
-#ifdef HAL_FMPI2C_MODULE_ENABLED
-#include "stm32f4xx_hal_fmpi2c.h"
-#endif /* HAL_FMPI2C_MODULE_ENABLED */
-
-#ifdef HAL_SPDIFRX_MODULE_ENABLED
-#include "stm32f4xx_hal_spdifrx.h"
-#endif /* HAL_SPDIFRX_MODULE_ENABLED */
-
-#ifdef HAL_DFSDM_MODULE_ENABLED
-#include "stm32f4xx_hal_dfsdm.h"
-#endif /* HAL_DFSDM_MODULE_ENABLED */
-
-#ifdef HAL_LPTIM_MODULE_ENABLED
-#include "stm32f4xx_hal_lptim.h"
-#endif /* HAL_LPTIM_MODULE_ENABLED */
-
-#ifdef HAL_MMC_MODULE_ENABLED
-#include "stm32f4xx_hal_mmc.h"
-#endif /* HAL_MMC_MODULE_ENABLED */
-
-/* Exported macro ------------------------------------------------------------*/
-#ifdef USE_FULL_ASSERT
-/**
-  * @brief  The assert_param macro is used for function's parameters check.
-  * @param  expr If expr is false, it calls assert_failed function
-  *         which reports the name of the source file and the source
-  *         line number of the call that failed.
-  *         If expr is true, it returns no value.
-  * @retval None
-  */
-#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
-/* Exported functions ------------------------------------------------------- */
-void assert_failed(uint8_t *file, uint32_t line);
-#else
-#define assert_param(expr) ((void)0U)
-#endif /* USE_FULL_ASSERT */
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __STM32F4xx_HAL_CONF_CUSTOM_H */
-
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

buildroot/share/PlatformIO/variants/MARLIN_STEVAL_F401VE/ldscript.ld

@@ -1,187 +0,0 @@
-/*
-*****************************************************************************
-**
-**  File        : ldscript.ld
-**
-**  Abstract    : Linker script for STM32F401RETx Device with
-**                512KByte FLASH, 96KByte RAM
-**
-**                Set heap size, stack size and stack location according
-**                to application requirements.
-**
-**                Set memory bank area and size if external memory is used.
-**
-**  Target      : STMicroelectronics STM32
-**
-**
-**  Distribution: The file is distributed as is, without any warranty
-**                of any kind.
-**
-*****************************************************************************
-** @attention
-**
-** <h2><center>&copy; COPYRIGHT(c) 2014 Ac6</center></h2>
-**
-** Redistribution and use in source and binary forms, with or without modification,
-** are permitted provided that the following conditions are met:
-**   1. Redistributions of source code must retain the above copyright notice,
-**      this list of conditions and the following disclaimer.
-**   2. Redistributions in binary form must reproduce the above copyright notice,
-**      this list of conditions and the following disclaimer in the documentation
-**      and/or other materials provided with the distribution.
-**   3. Neither the name of Ac6 nor the names of its contributors
-**      may be used to endorse or promote products derived from this software
-**      without specific prior written permission.
-**
-** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-**
-*****************************************************************************
-*/
-
-/* Entry Point */
-ENTRY(Reset_Handler)
-
-/* Highest address of the user mode stack */
-_estack = 0x20018000;    /* end of RAM */
-/* Generate a link error if heap and stack don't fit into RAM */
-_Min_Heap_Size = 0x200;      /* required amount of heap  */
-_Min_Stack_Size = 0x400; /* required amount of stack */
-
-/* Specify the memory areas */
-MEMORY
-{
-FLASH (rx)      : ORIGIN = 0x08000000, LENGTH = 512K
-RAM (xrw)      : ORIGIN = 0x20000000, LENGTH = 96K
-}
-
-/* Define output sections */
-SECTIONS
-{
-  /* The startup code goes first into FLASH */
-  .isr_vector :
-  {
-    . = ALIGN(4);
-    KEEP(*(.isr_vector)) /* Startup code */
-    . = ALIGN(4);
-  } >FLASH
-
-  /* The program code and other data goes into FLASH */
-  .text :
-  {
-    . = ALIGN(4);
-    *(.text)           /* .text sections (code) */
-    *(.text*)          /* .text* sections (code) */
-    *(.glue_7)         /* glue arm to thumb code */
-    *(.glue_7t)        /* glue thumb to arm code */
-    *(.eh_frame)
-
-    KEEP (*(.init))
-    KEEP (*(.fini))
-
-    . = ALIGN(4);
-    _etext = .;        /* define a global symbols at end of code */
-  } >FLASH
-
-  /* Constant data goes into FLASH */
-  .rodata :
-  {
-    . = ALIGN(4);
-    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
-    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
-    . = ALIGN(4);
-  } >FLASH
-
-  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
-  .ARM : {
-    __exidx_start = .;
-    *(.ARM.exidx*)
-    __exidx_end = .;
-  } >FLASH
-
-  .preinit_array     :
-  {
-    PROVIDE_HIDDEN (__preinit_array_start = .);
-    KEEP (*(.preinit_array*))
-    PROVIDE_HIDDEN (__preinit_array_end = .);
-  } >FLASH
-  .init_array :
-  {
-    PROVIDE_HIDDEN (__init_array_start = .);
-    KEEP (*(SORT(.init_array.*)))
-    KEEP (*(.init_array*))
-    PROVIDE_HIDDEN (__init_array_end = .);
-  } >FLASH
-  .fini_array :
-  {
-    PROVIDE_HIDDEN (__fini_array_start = .);
-    KEEP (*(SORT(.fini_array.*)))
-    KEEP (*(.fini_array*))
-    PROVIDE_HIDDEN (__fini_array_end = .);
-  } >FLASH
-
-  /* used by the startup to initialize data */
-  _sidata = LOADADDR(.data);
-
-  /* Initialized data sections goes into RAM, load LMA copy after code */
-  .data :
-  {
-    . = ALIGN(4);
-    _sdata = .;        /* create a global symbol at data start */
-    *(.data)           /* .data sections */
-    *(.data*)          /* .data* sections */
-
-    . = ALIGN(4);
-    _edata = .;        /* define a global symbol at data end */
-  } >RAM AT> FLASH
-
-
-  /* Uninitialized data section */
-  . = ALIGN(4);
-  .bss :
-  {
-    /* This is used by the startup in order to initialize the .bss section */
-    _sbss = .;         /* define a global symbol at bss start */
-    __bss_start__ = _sbss;
-    *(.bss)
-    *(.bss*)
-    *(COMMON)
-
-    . = ALIGN(4);
-    _ebss = .;         /* define a global symbol at bss end */
-    __bss_end__ = _ebss;
-  } >RAM
-
-  /* User_heap_stack section, used to check that there is enough RAM left */
-  ._user_heap_stack :
-  {
-    . = ALIGN(4);
-    PROVIDE ( end = . );
-    PROVIDE ( _end = . );
-    . = . + _Min_Heap_Size;
-    . = . + _Min_Stack_Size;
-    . = ALIGN(4);
-  } >RAM
-
-
-
-  /* Remove information from the standard libraries */
-  /DISCARD/ :
-  {
-    libc.a ( * )
-    libm.a ( * )
-    libgcc.a ( * )
-  }
-
-  .ARM.attributes 0 : { *(.ARM.attributes) }
-}
-
-

buildroot/share/PlatformIO/variants/MARLIN_STEVAL_F401VE/variant.cpp

@@ -1,310 +0,0 @@
-/*
- *******************************************************************************
- * Copyright (c) 2017, STMicroelectronics
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * 1. Redistributions of source code must retain the above copyright notice,
- *    this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- *    this list of conditions and the following disclaimer in the documentation
- *    and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- *    may be used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *******************************************************************************
- */
-
-#include "pins_arduino.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-#ifdef ARDUINO_STEVAL
-// Pin number
-// This array allows to wrap Arduino pin number(Dx or x)
-// to STM32 PinName (PX_n)
-const PinName digitalPin[] = {
-  PA_9,  // TX
-  PA_10, // RX
-
-  // WIFI
-  PD_3,  // CTS
-  PD_4,  // RTS
-  PD_5,  // TX
-  PD_6,  // RX
-  PB_5,  // WIFI_WAKEUP
-  PE_11, // WIFI_RESET
-  PE_12, // WIFI_BOOT
-
-  // STATUS_LED
-  PE_1,  //STATUS_LED
-
-  // SPI USER
-  PB_12, // SPI_CS
-  PB_15, // SPI_MOSI
-  PB_14, // SPI_MISO
-  PB_13, // SPI_SCK
-
-  // I2C USER
-  PB_7,  // SDA
-  PB_6,  // SCL
-
-  // SPI
-  PA_4,  // SPI_CS
-  PA_5,  // SPI_SCK
-  PA_6,  // SPI_MISO
-  PA_7,  // SPI_MOSI
-
-  // JTAG
-  PA_13, // JTAG_TMS/SWDIO
-  PA_14, // JTAG_TCK/SWCLK
-  PB_3,  // JTAG_TDO/SWO
-
-  // SDCARD
-  PC_8,  // SDIO_D0
-  PC_9,  // SDIO_D1
-  PA_15, // SD_CARD_DETECT
-  PC_10, // SDIO_D2
-  PC_11, // SDIO_D3
-  PC_12, // SDIO_CK
-  PD_2,  // SDIO_CMD
-
-  // OTG
-  PA_11, // OTG_DM
-  PA_12, // OTG_DP
-
-  // IR/PROBE
-  PD_1,  // IR_OUT
-  PC_1,  // IR_ON
-
-  // USER_PINS
-  PD_7,  // USER3
-  PB_9,  // USER1
-  PE_0,  // USER2
-  PB_4,  // USER4
-
-  // USERKET
-  PE_7,  // USER_BUTTON
-
-  // ENDSTOPS
-  PD_8,  // X_STOP
-  PD_9,  // Y_STOP
-  PD_10, // Z_STOP
-  PD_11, // U_STOP
-  PA_8,  // V_STOP
-  PD_0,  // W_STOP
-
-  // HEATERS
-  PD_13, // BED_HEAT_2
-  PD_14, // BED_HEAT_1
-  PD_15, // BED_HEAT_3
-  PC_7,  // E1_HEAT_PWM
-  PB_0,  // E2_HEAT_PWM
-  PB_1,  // E3_HEAT_PWM
-
-  // THERMISTOR
-  PC_2,  // BED_THERMISTOR_1
-  PC_3,  // BED_THERMISTOR_2
-  PA_3,  // BED_THERMISTOR_3
-  PA_0,  // E1_THERMISTOR
-  PA_1,  // E2_THERMISTOR
-  PA_2,  // E3_THERMISTOR
-
-  // FANS
-  PC_4,  // E1_FAN
-  PC_5,  // E2_FAN
-  PE_8,  // E3_FAN
-
-  // X_MOTOR
-  PE_13, // X_RESET
-  PE_14, // X_PWM
-  PE_15, // X_DIR
-
-  // Y_MOTOR
-  PE_10, // Y_RESET
-  PB_10, // Y_PWM
-  PE_9,  // Y_DIR
-
-  // Z_MOTOR
-  PC_15, // Z_RESET
-  PC_6,  // Z_PWM
-  PC_0,  // Z_DIR
-
-  // E1_MOTOR
-  PC_14, // E1_RESET
-  PC_13, // E1_DIR
-  PD_12, // E1_PWM
-
-  // E2_MOTOR
-  PE_4,  // E2_RESET
-  PE_5,  // E2_PWM
-  PE_6,  // E2_DIR
-
-  // E3_MOTOR
-  PE_3,  // E3_RESET
-  PE_2,  // E3_DIR
-  PB_8   // E3_PWM
-};
-#endif
-
-#ifdef __cplusplus
-}
-#endif
-
-// ----------------------------------------------------------------------------
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-/**
-  * @brief  System Clock Configuration
-  *         The system Clock is configured as follow :
-  *            System Clock source            = PLL (HSI)
-  *            SYSCLK(Hz)                     = 84000000
-  *            HCLK(Hz)                       = 84000000
-  *            AHB Prescaler                  = 1
-  *            APB1 Prescaler                 = 2
-  *            APB2 Prescaler                 = 1
-  *            HSI Frequency(Hz)              = 16000000
-  *            PLL_M                          = 16
-  *            PLL_N                          = 336
-  *            PLL_P                          = 4
-  *            PLL_Q                          = 7
-  *            VDD(V)                         = 3.3
-  *            Main regulator output voltage  = Scale2 mode
-  *            Flash Latency(WS)              = 2
-  * @param  None
-  * @retval None
-  */
-WEAK void SystemClock_Config(void)
-{
-  RCC_OscInitTypeDef RCC_OscInitStruct = {};
-  RCC_ClkInitTypeDef RCC_ClkInitStruct = {};
-
-  /* Configure the main internal regulator output voltage */
-  __HAL_RCC_PWR_CLK_ENABLE();
-  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
-  /* Initializes the CPU, AHB and APB busses clocks */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
-  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
-  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
-  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-  RCC_OscInitStruct.PLL.PLLM = 15;
-  RCC_OscInitStruct.PLL.PLLN = 144;
-  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
-  RCC_OscInitStruct.PLL.PLLQ = 5;
-  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
-    Error_Handler();
-  }
-  /* Initializes the CPU, AHB and APB busses clocks */
-  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
-                                | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
-  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
-  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
-  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
-
-  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) {
-    Error_Handler();
-  }
-}
-
-#ifdef __cplusplus
-}
-#endif
-
-
-// PA_0  54 // E1_THERMISTOR
-// PA_1  55 // E2_THERMISTOR
-// PA_2  56 // E3_THERMISTOR
-// PA_3  53 // BED_THERMISTOR_3
-// PA_4  16 // SPI_CS
-// PA_5  17 // SPI_SCK
-// PA_6  18 // SPI_MISO
-// PA_7  19 // SPI_MOSI
-// PA_8  43 // V_STOP
-// PA_9   0 //TX
-// PA_10  1 //RX
-// PA_11 30 //OTG_DM
-// PA_12 31 //OTG_DP
-// PA_13 20 // JTAG_TMS/SWDIO
-// PA_14 21 // JTAG_TCK/SWCLK
-// PA_15 25 // SD_CARD_DETECT
-// PB_0  49 // E2_HEAT_PWM
-// PB_1  50 // E3_HEAT_PWM
-// PB_3  22 // JTAG_TDO/SWO
-// PB_4  37 // USER4
-// PB_5   6 // WIFI_WAKEUP
-// PB_6  15 // SCL
-// PB_7  14 // SDA
-// PB_8  77 // E3_PWM
-// PB_9  35 // USER1
-// PB_10 64 // Y_PWM
-// PB_12 10 // SPI_CS
-// PB_13 13 // SPI_SCK
-// PB_14 12 // SPI_MISO
-// PB_15 11 // SPI_MOSI
-// PC_0  68 // Z_DIR
-// PC_1  33 //IR_ON
-// PC_2  51 // BED_THERMISTOR_1
-// PC_3  52 // BED_THERMISTOR_2
-// PC_4  57 // E1_FAN
-// PC_5  58 // E2_FAN
-// PC_6  67 // Z_PWM
-// PC_7  48 // E1_HEAT_PWM
-// PC_8  23 // SDIO_D0
-// PC_9  24 // SDIO_D1
-// PC_10 26 // SDIO_D2
-// PC_11 27 // SDIO_D3
-// PC_12 28 // SDIO_CK
-// PC_13 70 // E1_DIR
-// PC_14 69 // E1_RESET
-// PC_15 66 // Z_RESET
-// PD_0  44 // W_STOP
-// PD_1  32 //IR_OUT
-// PD_2  29 // SDIO_CMD
-// PD_3   2 // CTS
-// PD_4   3 // RTS
-// PD_5   4 // TX
-// PD_6   5 // RX
-// PD_7  34 // USER3
-// PD_8  39 // X_STOP
-// PD_9  40 // Y_STOP
-// PD_10 41 // Z_STOP
-// PD_11 42 // U_STOP
-// PD_12 71 // E1_PWM
-// PD_13 45 // BED_HEAT_2
-// PD_14 46 // BED_HEAT_1
-// PD_15 47 // BED_HEAT_3
-// PE_0  36 // USER2
-// PE_1   9 // STATUS_LED
-// PE_2  76 // E3_DIR
-// PE_3  75 // E3_RESET
-// PE_4  72 // E2_RESET
-// PE_5  73 // E2_PWM
-// PE_6  74 // E2_DIR
-// PE_7  38 // USER_BUTTON
-// PE_8  59 // E3_FAN
-// PE_9  65 // Y_DIR
-// PE_10 63 // Y_RESET
-// PE_11  7 // WIFI_RESET
-// PE_12  8 // WIFI_BOOT
-// PE_13 60 // X_RESET
-// PE_14 61 // X_PWM
-// PE_15 62 // X_DIR

buildroot/share/PlatformIO/variants/MARLIN_STEVAL_F401VE/variant.h

@@ -1,327 +0,0 @@
-/*
- *******************************************************************************
- * Copyright (c) 2017, STMicroelectronics
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * 1. Redistributions of source code must retain the above copyright notice,
- *    this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- *    this list of conditions and the following disclaimer in the documentation
- *    and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- *    may be used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *******************************************************************************
- */
-
-#ifndef _VARIANT_ARDUINO_STM32_
-#define _VARIANT_ARDUINO_STM32_
-/*----------------------------------------------------------------------------
- *        Headers
- *----------------------------------------------------------------------------*/
-
-#ifdef __cplusplus
-extern "C" {
-#endif // __cplusplus
-
-/*----------------------------------------------------------------------------
- *        Pins
- *----------------------------------------------------------------------------*/
-#ifdef ARDUINO_STEVAL
-
-
-/*----------------------------------------------------------------------------
- *        Pins
- *----------------------------------------------------------------------------*/
-// USART1_MAIN
-#define PA9  0 //TX
-#define PA10 1 //RX
-
-// WIFI (USART2)
-#define PD3   2 // CTS
-#define PD4   3 // RTS
-#define PD5   4 // TX
-#define PD6   5 // RX
-#define PB5   6 // WIFI_WAKEUP
-#define PE11  7 // WIFI_RESET
-#define PE12  8 // WIFI_BOOT
-
-// STATUS_LED
-#define PE1   9 // STATUS_LED
-
-// SPI USER
-#define PB12 10 // SPI_CS
-#define PB15 11 // SPI_MOSI
-#define PB14 12 // SPI_MISO
-#define PB13 13 // SPI_SCK
-
-// I2C USER
-#define PB7  14 // SDA
-#define PB6  15 // SCL
-
-// SPI
-#define PA4  16 // SPI_CS
-#define PA5  17 // SPI_SCK
-#define PA6  18 // SPI_MISO
-#define PA7  19 // SPI_MOSI
-
-// JTAG
-#define PA13 20 // JTAG_TMS/SWDIO
-#define PA14 21 // JTAG_TCK/SWCLK
-#define PB3  22 // JTAG_TDO/SWO
-
-// SDCARD
-#define PC8  23 // SDIO_D0
-#define PC9  24 // SDIO_D1
-#define PA15 25 // SD_CARD_DETECT
-#define PC10 26 // SDIO_D2
-#define PC11 27 // SDIO_D3
-#define PC12 28 // SDIO_CK
-#define PD2  29 // SDIO_CMD
-
-// OTG
-#define PA11 30 //OTG_DM
-#define PA12 31 //OTG_DP
-
-// IR/PROBE
-#define PD1  32 //IR_OUT
-#define PC1  33 //IR_ON
-
-// USER_PINS
-#define PD7  34 // USER3
-#define PB9  35 // USER1
-#define PE0  36 // USER2
-#define PB4  37 // USER4
-
-// USERKET
-#define PE7  38 // USER_BUTTON
-
-// ENDSTOPS
-#define PD8  39 // X_STOP
-#define PD9  40 // Y_STOP
-#define PD10 41 // Z_STOP
-#define PD11 42 // U_STOP
-#define PA8  43 // V_STOP
-#define PD0  44 // W_STOP
-
-// HEATERS
-#define PD13 45 // BED_HEAT_2
-#define PD14 46 // BED_HEAT_1
-#define PD15 47 // BED_HEAT_3
-#define PC7  48 // E1_HEAT_PWM
-#define PB0  49 // E2_HEAT_PWM
-#define PB1  50 // E3_HEAT_PWM
-
-// THERMISTOR
-#define PC2  51 // BED_THERMISTOR_1
-#define PC3  52 // BED_THERMISTOR_2
-#define PA3  53 // BED_THERMISTOR_3
-#define PA0  54 // E1_THERMISTOR
-#define PA1  55 // E2_THERMISTOR
-#define PA2  56 // E3_THERMISTOR
-
-// FANS
-#define PC4  57 // E1_FAN
-#define PC5  58 // E2_FAN
-#define PE8  59 // E3_FAN
-
-// X_MOTOR
-#define PE13 60 // X_RESET
-#define PE14 61 // X_PWM
-#define PE15 62 // X_DIR
-
-// Y_MOTOR
-#define PE10 63 // Y_RESET
-#define PB10 64 // Y_PWM
-#define PE9  65 // Y_DIR
-
-// Z_MOTOR
-#define PC15 66 // Z_RESET
-#define PC6  67 // Z_PWM
-#define PC0  68 // Z_DIR
-
-// E1_MOTOR
-#define PC14 69 // E1_RESET
-#define PC13 70 // E1_DIR
-#define PD12 71 // E1_PWM
-
-// E2_MOTOR
-#define PE4  72 // E2_RESET
-#define PE5  73 // E2_PWM
-#define PE6  74 // E2_DIR
-
-// E3_MOTOR
-#define PE3  75 // E3_RESET
-#define PE2  76 // E3_DIR
-#define PB8  77 // E3_PWM
-
-// This must be a literal
-#define NUM_DIGITAL_PINS        78
-// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
-#define NUM_ANALOG_INPUTS       6
-#define NUM_ANALOG_FIRST        51
-
-// On-board LED pin number
-#define LED_BUILTIN             PE1
-#define LED_GREEN               LED_BUILTIN
-
-// On-board user button
-#define USER_BTN                PE7
-
-// UART Definitions
-#define SERIAL_UART_INSTANCE    1 // Connected to ST-Link
-//#define SERIAL_UART_INSTANCE    2 // Connected to WIFI
-
-// Default pin used for 'Serial' instance (ex: ST-Link)
-// Mandatory for Firmata
-#if SERIAL_UART_INSTANCE == 1             // ST-Link & J23
-  #define PIN_SERIAL_RX         PA10
-  #define PIN_SERIAL_TX         PA9
-#elif SERIAL_UART_INSTANCE == 2         // WIFI interface
-  #define PIN_SERIAL2_RX        PD6
-  #define PIN_SERIAL2_TX        PD5
-#else
-  #error "Invalid setting for SERIAL_UART_INSTANCE."
-#endif
-
-// Timer Definitions
-#define TIMER_SERVO             TIM4  // TIMER_SERVO must be defined in this file
-#define TIMER_TONE              TIM5  // TIMER_TONE must be defined in this file
-
-/* SD detect signal */
-/*
- * By default, R67 is not provided, so SD card detect is not used.
- * Note: SD CD (pin 16 of expansion connector J23) can be connected
- * to GND in order to be able to use SD_DETECT_PIN
- */
-/*#define SD_DETECT_PIN           PA15*/
-
-/* HAL configuration */
-#define HSE_VALUE               25000000U
-
-/* Extra HAL modules */
-#define HAL_SD_MODULE_ENABLED
-
-#endif
-
-#ifdef __cplusplus
-} // extern "C"
-#endif
-/*----------------------------------------------------------------------------
- *        Arduino objects - C++ only
- *----------------------------------------------------------------------------*/
-
-#ifdef __cplusplus
-// These serial port names are intended to allow libraries and architecture-neutral
-// sketches to automatically default to the correct port name for a particular type
-// of use.  For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
-// the first hardware serial port whose RX/TX pins are not dedicated to another use.
-//
-// SERIAL_PORT_MONITOR        Port which normally prints to the Arduino Serial Monitor
-//
-// SERIAL_PORT_USBVIRTUAL     Port which is USB virtual serial
-//
-// SERIAL_PORT_LINUXBRIDGE    Port which connects to a Linux system via Bridge library
-//
-// SERIAL_PORT_HARDWARE       Hardware serial port, physical RX & TX pins.
-//
-// SERIAL_PORT_HARDWARE_OPEN  Hardware serial ports which are open for use.  Their RX & TX
-//                            pins are NOT connected to anything by default.
-#define SERIAL_PORT_MONITOR     Serial
-#define SERIAL_PORT_HARDWARE    Serial1
-#endif
-
-#endif // _VARIANT_ARDUINO_STM32_
-
-// PA0  54 // E1_THERMISTOR
-// PA1  55 // E2_THERMISTOR
-// PA2  56 // E3_THERMISTOR
-// PA3  53 // BED_THERMISTOR_3
-// PA4  16 // SPI_CS
-// PA5  17 // SPI_SCK
-// PA6  18 // SPI_MISO
-// PA7  19 // SPI_MOSI
-// PA8  43 // V_STOP
-// PA9   0 //TX
-// PA10  1 //RX
-// PA11 30 //OTG_DM
-// PA12 31 //OTG_DP
-// PA13 20 // JTAG_TMS/SWDIO
-// PA14 21 // JTAG_TCK/SWCLK
-// PA15 25 // SD_CARD_DETECT
-// PB0  49 // E2_HEAT_PWM
-// PB1  50 // E3_HEAT_PWM
-// PB3  22 // JTAG_TDO/SWO
-// PB4  37 // USER4
-// PB5   6 // WIFI_WAKEUP
-// PB6  15 // SCL
-// PB7  14 // SDA
-// PB8  77 // E3_PWM
-// PB9  35 // USER1
-// PB10 64 // Y_PWM
-// PB12 10 // SPI_CS
-// PB13 13 // SPI_SCK
-// PB14 12 // SPI_MISO
-// PB15 11 // SPI_MOSI
-// PC0  68 // Z_DIR
-// PC1  33 //IR_ON
-// PC2  51 // BED_THERMISTOR_1
-// PC3  52 // BED_THERMISTOR_2
-// PC4  57 // E1_FAN
-// PC5  58 // E2_FAN
-// PC6  67 // Z_PWM
-// PC7  48 // E1_HEAT_PWM
-// PC8  23 // SDIO_D0
-// PC9  24 // SDIO_D1
-// PC10 26 // SDIO_D2
-// PC11 27 // SDIO_D3
-// PC12 28 // SDIO_CK
-// PC13 70 // E1_DIR
-// PC14 69 // E1_RESET
-// PC15 66 // Z_RESET
-// PD0  44 // W_STOP
-// PD1  32 //IR_OUT
-// PD2  29 // SDIO_CMD
-// PD3   2 // CTS
-// PD4   3 // RTS
-// PD5   4 // TX
-// PD6   5 // RX
-// PD7  34 // USER3
-// PD8  39 // X_STOP
-// PD9  40 // Y_STOP
-// PD10 41 // Z_STOP
-// PD11 42 // U_STOP
-// PD12 71 // E1_PWM
-// PD13 45 // BED_HEAT_2
-// PD14 46 // BED_HEAT_1
-// PD15 47 // BED_HEAT_3
-// PE0  36 // USER2
-// PE1   9 // STATUS_LED
-// PE2  76 // E3_DIR
-// PE3  75 // E3_RESET
-// PE4  72 // E2_RESET
-// PE5  73 // E2_PWM
-// PE6  74 // E2_DIR
-// PE7  38 // USER_BUTTON
-// PE8  59 // E3_FAN
-// PE9  65 // Y_DIR
-// PE10 63 // Y_RESET
-// PE11  7 // WIFI_RESET
-// PE12  8 // WIFI_BOOT
-// PE13 60 // X_RESET
-// PE14 61 // X_PWM
-// PE15 62 // X_DIR

buildroot/tests/FYSETC_F6

@@ -18,15 +18,11 @@ exec_test $1 $2 "FYSETC F6 1.3 with DGUS" "$3"
 # Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2
 #
 use_example_configs delta/generic
-opt_set MOTHERBOARD BOARD_FYSETC_F6_13 \
-        LCD_LANGUAGE ko_KR \
-        X_DRIVER_TYPE L6470 Y_DRIVER_TYPE L6470 Z_DRIVER_TYPE L6470 \
-        L6470_CHAIN_SCK_PIN 53 L6470_CHAIN_MISO_PIN 49 L6470_CHAIN_MOSI_PIN 40 L6470_CHAIN_SS_PIN 42 \
-        'ENABLE_RESET_L64XX_CHIPS(V)' NOOP
+opt_set MOTHERBOARD BOARD_FYSETC_F6_13 LCD_LANGUAGE ko_KR
 opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \
            Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL UBL_MESH_WIZARD \
            OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU
-exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
+exec_test $1 $2 "DELTA, FYSETC F6 1.3, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
 
 #
 # Test mixed TMC config

buildroot/tests/STM32F401VE_STEVAL

@@ -1,15 +0,0 @@
-#!/usr/bin/env bash
-#
-# Build tests for STM32F401VE_STEVAL
-#
-
-# exit on first failure
-set -e
-
-# Build examples
-restore_configs
-opt_set MOTHERBOARD BOARD_STEVAL_3DP001V1 SERIAL_PORT -1
-exec_test $1 $2 "STM32F401VE_STEVAL Default Config" "$3"
-
-# cleanup
-restore_configs

ini/features.ini

@@ -26,8 +26,6 @@ HAS_MOTOR_CURRENT_I2C                  = SlowSoftI2CMaster
                                          src_filter=+<src/feature/digipot>
 HAS_TMC26X                             = TMC26XStepper=https://github.com/MarlinFirmware/TMC26XStepper/archive/master.zip
                                          src_filter=+<src/module/stepper/TMC26X.cpp>
-HAS_L64XX                              = Arduino-L6470@0.8.0
-                                         src_filter=+<src/libs/L64XX> +<src/module/stepper/L64xx.cpp> +<src/gcode/feature/L6470> +<src/HAL/shared/HAL_spi_L6470.cpp>
 LIB_INTERNAL_MAX31865                  = src_filter=+<src/libs/MAX31865.cpp>
 NEOPIXEL_LED                           = adafruit/Adafruit NeoPixel@~1.8.0
                                          src_filter=+<src/feature/leds/neopixel.cpp>

ini/stm32f4.ini

@@ -29,17 +29,6 @@ build_flags   = ${common_stm32.build_flags}
                 -O2 -ffreestanding -fsigned-char -fno-move-loop-invariants -fno-strict-aliasing
 
 #
-# STM32F401VE
-# 'STEVAL-3DP001V1' STM32F401VE board - https://www.st.com/en/evaluation-tools/steval-3dp001v1.html
-#
-[env:STM32F401VE_STEVAL]
-extends           = stm32_variant
-board             = marlin_STEVAL_STM32F401VE
-build_flags       = ${stm32_variant.build_flags}
-                    -DSTM32F401xE -DDISABLE_GENERIC_SERIALUSB
-                    -DUSBD_USE_CDC_COMPOSITE -DUSE_USB_FS
-
-#
 # STM32F401RC
 #
 [env:FYSETC_CHEETAH_V20]